LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * Designed for ease in circuit board assembly. * Black case enhance contrast ratio. * Solid state light source. * Reliable and rugged. Package Dimensions Lamp Part No. Lens Source Color LTL-10223WP Red Diffused Hi.Eff.Red Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25mm(.010") unless otherwise noted. 3. The holder color is black. 4. The holder raw material is PC. 5. Specifications are subject to change without notice. Part No. : LTL-523-11 BNS-OD-C131/A4 Page : 1 of 6 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Absolute Maximum Ratings at Ta=25℃ Parameter Maximum Rating Unit 100 mW 120 mA DC Forward Current 30 mA Derating Linear From 50℃ 0.4 mA/℃ 5 V Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) Reverse Voltage Operating Temperature Range -55℃ to + 100℃ Storage Temperature Range -55℃ to + 100℃ Lead Soldering Temperature [1.6mm(.063") From Body] Part No. : LTL-523-11 BNS-OD-C131/A4 260℃ for 5 Seconds Page : 2 of 6 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electrical Optical Characteristics at Ta=25℃ Parameter Symbol Min. Typ. IV 19 60 mcd 2θ1/2 60 deg Peak Emission Wavelength λp 635 nm Dominant Wavelength λd 623 nm Spectral Line Half-Width Δλ 40 nm Forward Voltage VF 2.0 Reverse Current IR Capacitance C Luminous Intensity Viewing Angle 20 Max. Unit Test Condition IF = 10 mA Note 1,4 Note 2 (Fig.6) Measurement @Peak (Fig.1) Note 3 2.6 V IF = 20 mA 100 μA VR = 5V PF VF = 0 , f = 1MHZ NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Iv needs ±15% additionary for guaranteed limits. Part No. : LTL-523-11 BNS-OD-C131/A4 Page : 3 of 6 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Part No. : LTL-523-11 BNS-OD-C131/A4 Page : 4 of 6 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications). Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant or in a dessicator with nitrogen ambient. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary. 4. Lead Forming & Assembly During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens. Do not use the base of the leadframe as a fulcrum during forming. Lead forming must be done before soldering at normal temperature. During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress 5. Soldering When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point. Dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering condition (for Lamp): Soldering iron Wave soldering 300°C Max. 3 sec. Max. (one time only) Temperature Soldering time Pre-heat Pre-heat time Solder wave Soldering time 100°C Max. 60 sec. Max. 260°C Max. 10 sec. Max. Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR re-flow is not suitable process for through hole type LED lamp production. 6. Drive Method An LED is a current operated device, In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application; it is recommended that a current limiting resistor be incorporated in the drive circuit. In series with each LED as shown in Circuit A below. (A) Recommended circuit. Circuit model A LED Circuit model B LED (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs Part No. : LTL-523-11 BNS-OD-C131/A4 Page : 5 of 6 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 7. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL-523-11 BNS-OD-C131/A4 Page : 6 of 6