17.0-21.0 GHz GaAs MMIC Power Amplifier Velocium Products 18 - 20 GHz HPA - APH478 P1009 May 2006 - Rev 10-May-06 Features Excellent Linear Output Amplifier Stage 20.0 dB Small Signal Gain +29.5 dBm P1dB Compression Point +38.0 dBm Third Order Intercept (OIP3) 100% On-Wafer RF, DC and Output Power Testing 100% Visual Inspection to MIL-STD-883 Method 2010 Chip Device Layout General Description Mimix Broadband’s two stage 17.0-21.0 GHz GaAs MMIC power amplifier is optimized for linear operation with a third order intercept point of +38.0 dBm. This MMIC uses Mimix Broadband’s 0.15 µm GaAs PHEMT device model technology, and is based upon electron beam lithography to ensure high repeatability and uniformity. The chip has surface passivation to protect and provide a rugged part with backside via holes and gold metallization to allow either a conductive epoxy or eutectic solder die attach process. This device is well suited for Millimeter-wave Point-to-Point Radio, LMDS, SATCOM and VSAT applications. Absolute Maximum Ratings Supply Voltage (Vd) Supply Current (Id1,2) Gate Bias Voltage Input Power (Pin) Storage Temperature (Tstg) Operating Temperature (Ta) Channel Temperature (Tch) +5.5 VDC 330,660 mA +0.3 VDC +12 dBm -65 to +165 OC -55 to MTTF TAble3 MTTF Table 3 (3) Channel temperature affects a device's MTTF. It is recommended to keep channel temperature as low as possible for maximum life. Electrical Characteristics (Ambient Temperature T = 25 oC) Parameter Frequency Range (f ) Input Return Loss (S11) Output Return Loss (S22) Small Signal Gain (S21) Gain Flatness ( S21) Reverse Isolation (S12) Output Power for 1 dB Compression (P1dB) 2 Output Third Order Intercept Point (OIP3) 1,2 Drain Bias Voltage (Vd1,2) Gate Bias Voltage (Vg1,2) Supply Current (Id) (Vd=5.0V, Vg=-0.3V Typical) Units GHz dB dB dB dB dB dBm dBm VDC VDC mA Min. 17.0 -1.0 - Typ. 8.0 7.0 20.0 +/-0.5 +29.5 +38.0 +5.0 -0.3 900 Max. 21.0 0.0 - (1) Measured at +18 dBm per tone output carrier level across the full frequency band. (2) Measured using constant current. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 1 of 6 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 17.0-21.0 GHz GaAs MMIC Power Amplifier Velocium Products 18 - 20 GHz HPA - APH478 P1009 May 2006 - Rev 10-May-06 Power Amplifier Measurements Measured performance characteristics (Typical at 25°C) Vd1= 5 V, Id= 30 0 mA; Vd2= 5V, Vd2= 600 mA 22 20 Pout (dBm) Gain (dB) 18 16 14 12 10 17 18 19 20 21 40 39 38 37 36 35 34 33 32 31 30 29 28 22 17 18 Frequency (GHz) -2 -1 Output Return Loss (dB) Input Return Loss (dB) 0 -4 -6 -8 -10 -12 18.5 19 Frequency (GHz) 19.5 21 22 20 20.5 IP3@18dBm/Tone Psat P1dB *Fixtured data 0 18 20 Frequency (GHz) *Fixtured data -14 17.5 19 -2 -3 -4 -5 -6 -7 -8 -9 17.5 18 18.5 19 19.5 20 20.5 Frequency (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 2 of 6 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 17.0-21.0 GHz GaAs MMIC Power Amplifier Velocium Products 18 - 20 GHz HPA - APH478 P1009 May 2006 - Rev 10-May-06 S-Parameters Measured performance characteristics (Typical at 25°C) Vd1= 5 V, Id= 30 0 mA; Vd2= 5V, Vd2= 600 mA FreqGHz 17.5 17.752 18.004 18.256 18.508 18.76 19.012 19.246 19.498 19.75 20.002 20.254 20.5 S11Mag -12.1 -11.083 -9.815 -8.232 -7.303 -6.66 -6.134 -6.229 -6.278 -7.16 -8.421 -10.568 -11.674 11Ang 152.45 148.677 141.67 137.03 134.36 135.133 136.387 140.378 142.695 146.815 152.483 158.787 165.758 S21Mag -49.302 -49.981 -48.911 -49.572 -50.903 -48.936 -51.589 -49.295 -46.339 -47.459 -49.064 -50.862 -46.658 21Ang 25.102 -2.561 -22.915 -31.609 -81.416 -101.36 -65.147 -83.276 -39.293 72.955 117.411 -7.302 43.109 S12Mag 20.483 20.551 20.729 20.672 20.761 20.685 20.604 20.443 20.622 20.326 20.405 20.472 20.552 S12Ang 89.053 78.835 53.522 28.712 5.571 -18.044 -40.128 -60.3 -82.436 -104.583 -127.721 -152.625 -164.338 Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com S22Mag -8.18 -7.96 -7.52 -7.192 -6.904 -6.632 -6.522 -6.538 -6.732 -7.011 -7.269 -7.822 -8.006 S22Ang 80.704 76.458 68.884 62.961 59.498 56.325 53.576 52.3 52.947 54.435 57.592 62.087 64.406 Page 3 of 6 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 17.0-21.0 GHz GaAs MMIC Power Amplifier P1009 May 2006 - Rev 10-May-06 Mechanical Drawing 1.280 (0.050) 0.736 (0.029) 2 1 6 0.0 0.0 5 4 0.736 (0.029) 3 0.785 1.185 1.585 (0.031) (0.047) (0.062) 3.920 (0.154) 2.185 (0.086) Units: millimeters (inches) Bond pad dimensions are shown to center of bond pad. Thickness: 0.110 +/- 0.010 (0.0043 +/- 0.0004), Backside is ground, Bond Pad/Backside Metallization: Gold All Bond Pads are 0.100 x 0.100 (0.004 x 0.004). Bond pad centers are approximately 0.109 (0.004) from the edge of the chip. Dicing tolerance: +/- 0.005 (+/- 0.0002). Approximate weight: 3.111 mg. Bond Pad #1 (RF In) Bond Pad #2 (RF Out) Bond Pad #3 (Vd2) Bond Pad #4 (Vg2) Bond Pad #5 (Vd1) Bond Pad #6 (Vg1) Bias Arrangement RF In 2 1 6 Vg1 5 4 Vd1 Bypass Capacitors - See App Note [2] 3 10 10 RF Out Vg2 Vd2 Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 4 of 6 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 17.0-21.0 GHz GaAs MMIC Power Amplifier P1009 May 2006 - Rev 10-May-06 App Note [1] Biasing - It is recommended to separately bias each stage at Vd(1,2)=5.0V Id1=300mA, and Id2=600mA. It is also recommended to use active biasing to keep the currents constant as the RF power and temperature vary; this gives the most reproducible results. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current and thus drain voltage. The typical gate voltage needed to do this is -0.3V. Typically the gate is protected with Silicon diodes to limit the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply. App Note [2] Bias Arrangement - For Parallel Stage Bias (Recommended for general applications) -- The same as Individual Stage Bias but all the drain or gate pad DC bypass capacitors (~100-200 pF) can be combined. Additional DC bypass capacitance (~0.01 uF) is also recommended to all DC or combination (if gate or drains are tied together) of DC bias pads. For Individual Stage Bias (Recommended for Saturated Applications) -- Each DC pad (Vd1,2 and Vg1,2) needs to have DC bypass capacitance (~100-200 pF) as close to the device as possible. Additional DC bypass capacitance (~0.01 uF) is also recommended. MTTF Table (TBD) These numbers were calculated based on accelerated life test information and thermal model analysis received from the fabricating foundry. Backplate Temperature Channel Temperature Rth MTTF Hours FITs 55 deg Celsius deg Celsius C/W E+ E+ 75 deg Celsius deg Celsius C/W E+ E+ 95 deg Celsius deg Celsius C/W E+ E+ Bias Conditions: Vd1=Vd2=5.0V, Id1=300 mA, Id2=600 mA Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 5 of 6 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 17.0-21.0 GHz GaAs MMIC Power Amplifier Velocium Products 18 - 20 GHz HPA - APH478 P1009 May 2006 - Rev 10-May-06 Handling and Assembly Information CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: Do not ingest. Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ESD - Gallium Arsenide (GaAs) devices are susceptible to electrostatic and mechanical damage. Die are supplied in antistatic containers, which should be opened in cleanroom conditions at an appropriately grounded antistatic workstation. Devices need careful handling using correctly designed collets, vacuum pickups or, with care, sharp tweezers. Die Attachment - GaAs Products from Mimix Broadband are 0.100 mm (0.004") thick and have vias through to the backside to enable grounding to the circuit. Microstrip substrates should be brought as close to the die as possible. The mounting surface should be clean and flat. If using conductive epoxy, recommended epoxies are Ablestick 84-1LMI or 84-1LMIT cured in a nitrogen atmosphere per manufacturer's cure schedule. Apply epoxy sparingly to avoid getting any on to the top surface of the die. An epoxy fillet should be visible around the total die periphery. If eutectic mounting is preferred, then a fluxless gold-tin (AuSn) preform, approximately 0.001 2 thick, placed between the die and the attachment surface should be used. A die bonder that utilizes a heated collet and provides scrubbing action to ensure total wetting to prevent void formation in a nitrogen atmosphere is recommended. The gold-tin eutectic (80% Au 20% Sn) has a melting point of approximately 280 C (Note: Gold Germanium should be avoided). The work station temperature should be 310 C +- 10 C. Exposure to these extreme temperatures should be kept to minimum. The collet should be heated, and the die pre-heated to avoid excessive thermal shock. Avoidance of air bridges and force impact are critical during placement. Wire Bonding - Windows in the surface passivation above the bond pads are provided to allow wire bonding to the die's gold bond pads. The recommended wire bonding procedure uses 0.076 mm x 0.013 mm (0.003" x 0.0005") 99.99% pure gold ribbon with 0.5-2% elongation to minimize RF port bond inductance. Gold 0.025 mm (0.001") diameter wedge or ball bonds are acceptable for DC Bias connections. Aluminum wire should be avoided. Thermo-compression bonding is recommended though thermosonic bonding may be used providing the ultrasonic content of the bond is minimized. Bond force, time and ultrasonics are all critical parameters. Bonds should be made from the bond pads on the die to the package or substrate. All bonds should be as short as possible. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 6 of 6 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.