43.5-46.5 GHz GaAs MMIC Power Amplifier P1015-BD August 2007 - Rev 10-Aug-07 Features Excellent Saturated Output Stage Balanced Design Provides Good Input/Output Match 13.0 dB Small Signal Gain +31.0 dBm P1dB Compression Point 100% On-Wafer RF, DC and Output Power Testing 100% Visual Inspection to MIL-STD-883 Method 2010 Chip Device Layout General Description Mimix Broadband's three stage balanced 43.5 - 46.5 GHz GaAs MMIC power amplifier has a small signal gain of 13.0 dB with a +31.0 dBm P1dB output compression point. The device also includes Lange couplers to achieve good input and output return loss. This MMIC uses Mimix Broadband’s 0.15 µm GaAs PHEMT device model technology, and is based upon electron beam lithography to ensure high repeatability and uniformity. The chip has surface passivation to protect and provide a rugged part with backside via holes and gold metallization to allow either a conductive epoxy or eutectic solder die attach process. This device is well suited for Millimeter-wave Point-to-Point Radio, LMDS, SATCOM and VSAT applications. Absolute Maximum Ratings Supply Voltage (Vd) Supply Current (Id1,2,3) Gate Bias Voltage (Vg) Input Power (Pin) Storage Temperature (Tstg) Operating Temperature (Ta) Channel Temperature (Tch) +6.0 VDC 945,945,1915 mA +0.3 VDC +26 dBm -65 to +165 OC -55 to MTTF Table1 MTTF Table 1 (1) Channel temperature affects a device's MTTF. It is recommended to keep channel temperature as low as possible for maximum life. Electrical Characteristics (Ambient Temperature T = 25 oC) Parameter Frequency Range (f ) Input Return Loss (S11) Output Return Loss (S22) Small Signal Gain (S21) Gain Flatness ( S21) Reverse Isolation (S12) Output Power for 1dB Compression (P1dB) 2 Drain Bias Voltage (Vd1,2,3) Gate Bias Voltage (Vg1,2,3) Supply Current (Id1) (Vd=5.0V, Vg=-0.5V Typical) Supply Current (Id2) (Vd=5.0V, Vg=-0.5V Typical) Supply Current (Id3) (Vd=5.0V, Vg=-0.5V Typical) Units GHz dB dB dB dB dB dBm VDC VDC mA mA mA Min. 43.5 -1.0 - Typ. 20.0 20.0 13.0 +/-1.0 45.0 +31.0 +5.0 -0.5 720 720 1440 Max. 46.5 +5.5 0.0 860 860 1740 (2) Measured using constant current. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 1 of 5 Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 43.5-46.5 GHz GaAs MMIC Power Amplifier P1015-BD August 2007 - Rev 10-Aug-07 Power Amplifier Measurements S parameters XP1015-BD wafer sweep XO1015-BD_wafer sweep: Pout vs. Freq at Pin=22 dBm 20 18 16 14 12 10 8 6 4 2 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 33 0475, DeviceCoord=R10C3 32.5 0475, DeviceCoord=R10C4 32 0475, DeviceCoord=R10C5 0475, DeviceCoord=R10C6 31.5 0475, DeviceCoord=R10C7 31 0475, DeviceCoord=R10C8 0475, DeviceCoord=R11C2 30.5 PoutCorr 0475, DeviceCoord=R11C4 30 0475, DeviceCoord=R11C6 29.5 0475, DeviceCoord=R11C8 0475, DeviceCoord=R12C2 29 0475, DeviceCoord=R12C5 28.5 0475, DeviceCoord=R12C7 28 0475, DeviceCoord=R13C4 0475, DeviceCoord=R13C5 27.5 0475, DeviceCoord=R13C7 27 0475, DeviceCoord=R9C2 0475, DeviceCoord=R9C3 26.5 0475, DeviceCoord=R9C4 35 36 37 38 39 40 41 42 43 44 Frequency (GHz) 45 46 47 48 49 50 26 0475, DeviceCoord=R9C5 25.5 25 43.4 0475, DeviceCoord=R9C6 0475, DeviceCoord=R9C7 43.5 43.6 43.7 43.8 43.9 44 44.1 44.2 44.3 44.4 44.5 44.6 freq (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 2 of 5 Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 43.5-46.5 GHz GaAs MMIC Power Amplifier P1015-BD August 2007 - Rev 10-Aug-07 Mechanical Drawing 1.226 (0.048) 1.725 (0.068) 2 3 4.630 (0.182) 2.620 (0.103) 2.225 2.625 (0.088) (0.103) 4 5 3.225 (0.127) 3.827 (0.151) 6 7 1 8 14 13 1.226 (0.048) 1.725 (0.068) 0.0 0.0 12 11 2.225 2.625 (0.088) (0.103) 10 9 3.225 (0.127) 3.827 (0.151) 2.006 (0.079) 4.650 (0.183) (Note: Engineering designator is 44MPA0475) Units: millimeters (inches) Bond pad dimensions are shown to center of bond pad. Thickness: 0.110 +/- 0.010 (0.0043 +/- 0.0004), Backside is ground, Bond Pad/Backside Metallization: Gold All DC Bond Pads are 0.100 x 0.100 (0.004 x 0.004). All RF Bond Pads are 0.100 x 0.200 (0.004 x 0.008) Bond pad centers are approximately 0.109 (0.004) from the edge of the chip. Dicing tolerance: +/- 0.005 (+/- 0.0002). Approximate weight: 13.349 mg. Bond Pad #1 (RF In) Bond Pad #2 (Vg1A) Bond Pad #3 (Vd1A) Bond Pad #4 (Vg2A) Bias Arrangement Vg1 2 RF In 3 Bond Pad #5 (Vd2A) Bond Pad #6 (Vg3A) Bond Pad #7 (Vd3A) Bond Pad #8 (RF Out) Vg2 4 5 Vg3 6 Bond Pad #9 (Vd3B) Bond Pad #10 (Vg3B) Bond Pad #11 Vd2B) Bond Pad #12 (Vg2B) Bond Pad #13 (Vd1B) Bond Pad #14 (Vg1B) Bypass Capacitors - See App Note [2] 7 1 8 14 13 12 Vd1 11 10 Vd2 RF Out 9 Vd3 Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 3 of 5 Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 43.5-46.5 GHz GaAs MMIC Power Amplifier P1015-BD August 2007 - Rev 10-Aug-07 App Note [1] Biasing - It is recommended to separately bias each amplifier stage Vd1 through Vd3 at Vd(1,2,3)=5.0V with Id1=Id2=720mA and Id3=1440mA. Separate biasing is recommended if the amplifier is to be used at high levels of saturation, where gate rectification will alter the effective gate control voltage. For non-critical applications it is possible to parallel all stages and adjust the common gate voltage for a total drain current Id(total)=2880 mA. It is also recommended to use active biasing to keep the currents constant as the RF power and temperature vary; this gives the most reproducible results. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current and thus drain voltage. The typical gate voltage needed to do this is -0.5V. Typically the gate is protected with Silicon diodes to limit the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply. App Note [2] Bias Arrangement - For Parallel Stage Bias (Recommended for general applications) -- The same as Individual Stage Bias but all the drain or gate pad DC bypass capacitors (~100-200 pF) can be combined. Additional DC bypass capacitance (~0.01 uF) is also recommended to all DC or combination (if gate or drains are tied together) of DC bias pads. All DC pads have been tied together on chip and can be biased from either side. For Individual Stage Bias (Recommended for saturated applications) -- Each DC pad (Vd1,2,3 and Vg1,2,3) needs to have DC bypass capacitance (~100-200 pF) as close to the device as possible. Additional DC bypass capacitance (~0.01 uF) is also recommended. All DC pads have been tied together on chip and can be biased from either side. MTTF Table (TBD) These numbers were calculated based on accelerated life test information and thermal model analysis received from the fabricating foundry. Backplate Temperature Channel Temperature Rth MTTF Hours FITs 55 deg Celsius deg Celsius C/W E+ E+ 75 deg Celsius deg Celsius C/W E+ E+ 95 deg Celsius deg Celsius C/W E+ E+ Bias Conditions: Vd1=Vd2=Vd3=5.0V, Id1=Id2=720 mA, Id3=1440 mA Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 4 of 5 Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 43.5-46.5 GHz GaAs MMIC Power Amplifier P1015-BD August 2007 - Rev 10-Aug-07 Handling and Assembly Information CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: • Do not ingest. • Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. • Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ESD - Gallium Arsenide (GaAs) devices are susceptible to electrostatic and mechanical damage. Die are supplied in antistatic containers, which should be opened in cleanroom conditions at an appropriately grounded anti-static workstation. Devices need careful handling using correctly designed collets, vacuum pickups or, with care, sharp tweezers. Die Attachment - GaAs Products from Mimix Broadband are 0.100 mm (0.004") thick and have vias through to the backside to enable grounding to the circuit. Microstrip substrates should be brought as close to the die as possible. The mounting surface should be clean and flat. If using conductive epoxy, recommended epoxies are Tanaka TS3332LD, Die Mat DM6030HK or DM6030HK-Pt cured in a nitrogen atmosphere per manufacturer's cure schedule. Apply epoxy sparingly to avoid getting any on to the top surface of the die. An epoxy fillet should be visible around the total die periphery. For additional information please see the Mimix "Epoxy Specifications for Bare Die" application note. If eutectic mounting is preferred, then a fluxless gold-tin (AuSn) preform, approximately 0.0012 thick, placed between the die and the attachment surface should be used. A die bonder that utilizes a heated collet and provides scrubbing action to ensure total wetting to prevent void formation in a nitrogen atmosphere is recommended. The gold-tin eutectic (80% Au 20% Sn) has a melting point of approximately 280 ºC (Note: Gold Germanium should be avoided). The work station temperature should be 310 ºC +/- 10 ºC. Exposure to these extreme temperatures should be kept to minimum. The collet should be heated, and the die pre-heated to avoid excessive thermal shock. Avoidance of air bridges and force impact are critical during placement. Wire Bonding - Windows in the surface passivation above the bond pads are provided to allow wire bonding to the die's gold bond pads. The recommended wire bonding procedure uses 0.076 mm x 0.013 mm (0.003" x 0.0005") 99.99% pure gold ribbon with 0.5-2% elongation to minimize RF port bond inductance. Gold 0.025 mm (0.001") diameter wedge or ball bonds are acceptable for DC Bias connections. Aluminum wire should be avoided. Thermo-compression bonding is recommended though thermosonic bonding may be used providing the ultrasonic content of the bond is minimized. Bond force, time and ultrasonics are all critical parameters. Bonds should be made from the bond pads on the die to the package or substrate. All bonds should be as short as possible. Ordering Information Part Number for Ordering XP1015-BD-000V XP1015-BD-EV1 Description Where “V” is RoHS compliant die packed in vacuum release gel paks XP1015 die evaluation module Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 5 of 5 Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.