CRYSTAL CLOCK OSCILLATORS Data Sheet 0515F Rev. F VCXO Series (PECL) SU-A369X Series PATENT PENDING Description The SU-A369X Series of voltage controlled quartz crystal oscillators provide frequency control by applying a voltage to Pin 1. This unit supplies DPECL compatible outputs which are enabled when Pin 2 is set to a logic low or left open. Features • Frequency range–300.0MHz to 1.500GHz • Wide Absolute Pull Range • Will withstand SMD reflow temperatures of 183°C for 4 minutes maximum • Space-saving alternative to discrete component oscillators • High shock resistance, to 1000g • 3.3 volt operation • Low Jitter - Wavecrest jitter characterization available • High Reliability - NEL HALT/HASS qualified for crystal oscillator start-up conditions • High Q Crystal actively tuned oscillator circuit • Power supply decoupling internal • No internal PLL avoids cascading PLL problems • High frequencies due to proprietary design • Gold plated pads Electrical Connection Pad 1 2 3 4 5 6 Connection VCO Enable VEE Output Output Complement VCC 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: [email protected] www.nelfc.com Data Sheet 0515F CRYSTAL CLOCK OSCILLATORS SU-A369X Series VCXO (PECL) Rev. F Continued Operating Conditions and Output Characteristics Electrical Characteristics Parameter Frequency Duty Cycle Logic 0 Logic 1 Rise & Fall Time Jitter, RMS(1) Absolute Pull Range(3) Vco input impedance Vco linearity Transfer Function (2) Modulation Bandwidth Enable Voltage (4) Disable Voltage Symbol --------VOL VOH tr,tf ----APR ------------MBW --------- Conditions ----@ VO /2 --------20-80%VO ----VCO=0.3 to 3.0V 50na dc current max VCO=0.3 to 3.0V VCO=0.3 to 3.0V @ -3dB, 0<VCO<3.3V with VEE=0V with VEE=0V Min 300.0MHz 45/55% Vcc-1.810Vdc Vcc-1.200Vdc ------------100K ohm --------25kHz 0V 2.0V Typical --------------------3 psec ±100ppm --------Positive ------------- Max 1.500GHz 55/45% Vcc-1.620Vdc Vcc-0.880Vdc 600 ps ------------10% --------0.8V VCC General Characteristics Parameter Supply Voltage Supply Current Output current Operating temperature Storage temperature Power Dissipation Lead temperature Load Symbol Conditions Min 3.3V±5% 3.135V VCC-VEE ICC ------------0.0 mA IO TA -----0°C TS -----55°C --------PD TL Soldering, 10 sec. ----50 Ohm to VCC-2V or Thevenin Equivalent, Bias Required Typical 3.3V ------------------------- Max 3.465V 150 mA ±50.0 mA 70°C 125°C 520 mW 300°C Environmental and Mechanical Characteristics Mechanical Shock Thermal Shock Vibration Soldering Condition Hermetic Seal Per MIL-STD-202, Method 213, Condition E Per MIL-STD-833, Method 1011, Condition A 0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz 300°C for 10 seconds Leak rate less than 1 x 10 -8 atm.cc/sec of helium Footnotes: 1) Jitter performance is frequency dependent. Please contact factory for full Wavecrest characterization. RMS jitter bandwidth of 12kHz to 20MHz. 2) Frequency increase with increase in control voltage and is monotonic. 3) Pullability is frequency dependant. Consult factory. 4) Open to Enable pin also enables the outputs Creating a Part Number SU - A369X - FREQ Package Code SU 6 Pad 9x14mm SMD Tolerance/Performance 1 ±50ppm 0-70°C 9 Customer Specific B ±50ppm -40 to +85°C Input Voltage Code Specification A 3.3V 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: [email protected] www.nelfc.com