NICHIA NSSW061AT

No. STSE-CC6048A
<Cat.No.060417>
SPECIFICATIONS FOR NICHIA CHIP TYPE WHITE
MODEL : NSSW061AT
NICHIA CORPORATION
-0-
LED
Nichia STSE-CC6048A-3
<Cat.No.061212>
1.SPECIFICATIONS
(1) Absolute Maximum Ratings
Item
Forward Current
Pulse Forward Current
Reverse Voltage
Power Dissipation
Operating Temperature
Storage Temperature
Soldering Temperature
IFP Conditions
Symbol
IF
IFP
VR
PD
Topr
Tstg
Tsld
Pulse Width <
= 10msec.
:
(2) Initial Electrical/Optical Characteristics
Symbol
Item
Forward Voltage
VF
Reverse Current
IR
Luminous Intensity
Iv
(Chromaticity Coordinate 1)
½
x
Chromaticity Coordinate 1
y
Luminous Intensity
Iv
(Chromaticity Coordinate 2)
½
x
Chromaticity Coordinate 2
y
-
Absolute Maximum Rating
35
100
5
123
-30 ~ + 85
-40 ~ +100
Reflow Soldering : 260°C
Hand Soldering : 350°C
and
(Ta=25°C)
Unit
mA
mA
V
mW
°C
°C
for 10sec.
for 3sec.
Duty <
= 1/10
(Ta=25°C)
Max.
Unit
3.5
V
50
µA
Condition
IF=20[mA]
VR= 5[V]
Typ.
(3.2)
-
IF=20[mA]
(960)
-
mcd
IF=20[mA]
IF=20[mA]
0.275
0.255
-
-
IF=20[mA]
(1050)
-
mcd
IF=20[mA]
IF=20[mA]
0.31
0.32
-
-
½ Please refer to CIE 1931 chromaticity diagram.
(3) Ranking
Item
Rank U12
Rank U11
Luminous Intensity Rank T22
Rank T21
Rank T12
Symbol
Iv
Iv
Iv
Iv
Iv
Condition
IF=20[mA]
IF=20[mA]
IF=20[mA]
IF=20[mA]
IF=20[mA]
Min.
1100
1000
930
860
790
(Ta=25°C)
Max.
Unit
1200
mcd
1100
mcd
1000
mcd
930
mcd
860
mcd
½ Luminous Intensity Measurement allowance is ± 10%.
Color Ranks
x
y
x
y
0.280
0.248
Rank a52
0.272
0.282
0.258
0.272
0.283
0.244
Rank a56
0.280
0.288
0.248
0.262
0.288
0.262
x
y
0.291
0.258
x
y
-1-
0.272
0.258
(IF=20mA,Ta=25°C)
Rank a55
0.268
0.277
0.282
0.263
0.278
0.272
0.288
0.262
Rank a62
0.282
0.291
0.272
0.287
0.296
0.276
Nichia STSE-CC6048A
<Cat.No.060417>
x
y
x
y
x
y
x
y
0.282
0.272
Rank a65
0.277
0.287
0.278
0.295
0.274
0.236
Rank u12
0.265
0.272
0.245
0.258
0.277
0.233
Rank u16
0.274
0.280
0.236
0.248
0.259
0.232
Rank u25
0.253
0.260
0.237
0.250
0.291
0.287
x
y
0.280
0.248
x
y
0.283
0.244
x
y
0.265
0.245
x
y
0.291
0.258
Rank a66
0.288
0.296
0.262
0.276
0.298
0.271
0.265
0.245
Rank u15
0.260
0.268
0.250
0.263
0.272
0.258
0.269
0.224
Rank u22
0.259
0.265
0.232
0.245
0.274
0.236
0.271
0.222
Rank u26
0.269
0.274
0.224
0.236
0.277
0.233
Color Coordinates Measurement allowance is ± 0.01.
One delivery will include up to four color ranks and three luminous intensity ranks of the products.
The quantity-ratio of the ranks is decided by Nichia.
2.INITIAL
OPTICAL/ELECTRICAL
CHARACTERISTICS
Please refer to figure’s page.
3.OUTLINE
DIMENSIONS
AND
MATERIALS
Please refer to figure’s page.
Material as follows ;
Package
Encapsulating Resin
Electrodes
Lens
:
:
:
:
-2-
Glass Fabric Based-Epoxy Resin
Resin (with Diffused + Phosphor)
Ag Plating Copper Alloy
Resin (Diffused)
Nichia STSE-CC6048A
<Cat.No.060417>
4.PACKAGING
· The LEDs are packed in cardboard boxes after taping.
Please refer to figure’s page.
The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity
· In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation.
· The LEDs may be damaged if the boxes are dropped or receive a strong impact against them,
so precautions must be taken to prevent any damage.
· The boxes are not water resistant and therefore must be kept away from water and moisture.
· When the LEDs are transported, we recommend that you use the same packing method as Nichia.
5.LOT
NUMBER
The first six digits number shows lot number.
The lot number is composed of the following characters;
-U
- Year
( 5 for 2005, 6 for 2006 )
- Month ( 1 for Jan., 9 for Sep., A for Oct.,
- Nichia's Product Number
U - Ranking by Color Coordinates
- Ranking by Luminous Intensity
-3-
B for Nov. )
Nichia STSE-CC6048A
<Cat.No.060417>
6.RELIABILITY
(1) TEST ITEMS AND RESULTS
Test Item
Resistance to
Soldering Heat
(Reflow Soldering)
Solderability
(Reflow Soldering)
Thermal Shock
Temperature Cycle
Moisture Resistance Cyclic
High Temperature Storage
Temperature Humidity
Storage
Low Temperature Storage
Steady State Operating Life
Condition 1
Steady State Operating Life
Condition 2
Steady State Operating Life
of High Temperature
Steady State Operating Life
of High Humidity Heat
Steady State Operating Life
of Low Temperature
Vibration
Standard
Test Method
JEITA ED-4701
300 301
JEITA ED-4701
300 303
JEITA ED-4701
300 307
JEITA ED-4701
100 105
JEITA ED-4701
200 203
JEITA ED-4701
200 201
JEITA ED-4701
100 103
JEITA ED-4701
200 202
JEITA ED-4701
400 403
Test Conditions
Tsld=260°C, 10sec.
(Pre treatment 30°C,70%,168hrs.)
Note
2 times
Number of
Damaged
0/50
Tsld=215 ± 5°C, 3sec.
(Lead Solder)
0°C ~ 100°C
15sec. 15sec.
-40°C ~ 25°C ~ 100°C ~ 25°C
30min. 5min. 30min. 5min.
25°C ~ 65°C ~ -10°C
90%RH 24hrs./1cycle
Ta=100°C
1 time
over 95%
20 cycles
0/50
100 cycles
0/50
10 cycles
0/50
1000 hrs.
0/50
Ta=60°C,
1000 hrs.
0/50
Ta=-40°C
1000 hrs.
0/50
Ta=25°C, IF=20mA
1000 hrs.
0/50
Ta=25°C, IF=35mA
500 hrs.
0/50
Ta=85°C, IF=8.5mA
1000 hrs.
0/50
60°C, RH=90%, IF=15mA
500 hrs.
0/50
Ta=-30°C, IF=20mA
1000 hrs.
0/50
48min.
0/50
1 time
0/50
1 time
0/50
RH=90%
Substrate Bending
JEITA ED-4702
100 ~ 2000 ~ 100Hz Sweep 4min.
200m/s2
3direction, 4cycles
3mm, 5 ± 1 sec.
Adhesion Strength
JEITA ED-4702
5N,
10 ± 1 sec.
0/50
(2) CRITERIA FOR JUDGING DAMAGE
Item
Symbol
Forward Voltage
VF
Reverse Current
IR
Luminous Intensity
IV
*) U.S.L. : Upper Standard Level
Test Conditions
Criteria for Judgement
Min.
Max.
IF=20mA
U.S.L.*)
VR=5V
U.S.L.*)
IF=20mA
L.S.L.**) 0.7
**) L.S.L. : Lower Standard Level
-4-
1.1
2.0
Nichia STSE-CC6048A-1
<Cat.No.060915>
7.CAUTIONS
The LEDs are devices which are materialized by combining Blue LEDs and special phosphors.
Consequently, the color of the LEDs is changed a little by an operating current.
Care should be taken after due consideration when using LEDs.
(1) Moisture Proof Package
· When moisture is absorbed into the SMT package it may vaporize and expand during soldering.
There is a possibility that this can cause exfoliation of the contacts and damage to the optical
characteristics of the LEDs.
For this reason, the moisture proof package is used to keep moisture
to a minimum in the package.
· The moisture proof package is made of an aluminum moisture proof bag.
A package of
a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag.
The silica gel changes its color from blue to pink as it absorbs moisture.
(2) Storage
· Storage Conditions
Before opening the package :
The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a
year.
When storing the LEDs, moisture proof packaging with absorbent material (silica gel)
is recommended.
After opening the package :
The LEDs should be kept at 30°C or less and 70%RH or less.
The LEDs should be soldered
within 168 hours (7days) after opening the package.
If unused LEDs remain, they should be
stored in moisture proof packages, such as sealed containers with packages of moisture absorbent
material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag
and to reseal the moisture proof bag again.
· If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage
time, baking treatment should be performed using the following conditions.
Baking treatment : more than 24 hours at 65 ± 5°C
· Nichia LED electrodes are silver plated copper alloy. The silver surface may be affected by
environments which contain corrosive substances. Please avoid conditions which may cause the LED
to corrode, tarnish or discolor. This corrosion or discoloration might lower solderability or might
affect on optical characteristics.
· Please avoid rapid transitions in ambient temperature, especially in high humidity environments where
condensation can occur.
(3) Heat Generation
· Thermal design of the end product is of paramount importance.
Please consider the heat generation
of the LED when making the system design. The coefficient of temperature increase per input
electric power is affected by the thermal resistance of the circuit board and density of LED placement
on the board, as well as other components. It is necessary to avoid intense heat generation and operate
within the maximum ratings given in this specification.
· The operating current should be decided after considering the ambient maximum temperature of LEDs.
-5-
Nichia STSE-CC6048A-2
<Cat.No.061129>
(4) Soldering Conditions
· The LEDs can be soldered in place using the reflow soldering method.
Nichia cannot make a
guarantee on the LEDs after they have been assembled using the dip soldering method.
· Recommended soldering conditions
Pre-heat
Pre-heat time
Peak
temperature
Soldering time
Condition
Reflow Soldering
Lead Solder
Lead-free Solder
180 ~ 200°C
120 ~ 150°C
120 sec. Max.
120 sec. Max.
240°C Max.
260°C Max.
Hand Soldering
Temperature
Soldering time
350°C Max.
3 sec. Max.
(one time only)
10 sec. Max.
10 sec. Max.
refer to
refer to
Temperature - profile 1. Temperature - profile 2.
(N2 reflow is recommended.)
Although the recommended soldering conditions are specified in the above table, reflow or hand
soldering at the lowest possible temperature is desirable for the LEDs.
A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.
[Temperature-profile (Surface of circuit board)]
Use the conditions shown to the under figure.
<1 : Lead Solder>
<2 : Lead-free Solder>
1~ 5°C / sec.
2.5 ~ 5°C / sec.
2.5 ~ 5°C / sec.
Pre-heating
120 ~ 150°C 60sec.Max.
Above 200°C
240°C Max.
10sec. Max.
1~ 5°C / sec.
Pre-heating
180 ~ 200°C 60sec.Max.
Above 220°C
260°C Max.
10sec. Max.
120sec.Max.
120sec.Max.
[optional soldering pad design]
Use the following conditions shown in the figure.
1.25
1
0.75
1
(Unit : mm)
· Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere
during air reflow.
It is recommended that the User use the nitrogen reflow method.
· Repairing should not be done after the LEDs have been soldered.
When repairing is unavoidable,
a double-head soldering iron should be used.
It should be confirmed beforehand whether the
characteristics of the LEDs will or will not be damaged by repairing.
· Reflow soldering should not be done more than two times.
· When soldering, do not put stress on the LEDs during heating.
· After soldering, do not warp the circuit board.
(5) Cleaning
· It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs.
When using
other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the
resin or not.
Freon solvents should not be used to clean the LEDs because of worldwide regulations.
· Do not clean the LEDs by the ultrasonic.
When it is absolutely necessary, the influence of ultrasonic
cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition.
Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur.
-6-
Nichia STSE-CC6048A-1
<Cat.No.060915>
(6) Static Electricity
· Static electricity or surge voltage damages the LEDs.
It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.
· All devices, equipment and machinery must be properly grounded. It is recommended that precautions
be taken against surge voltage to the equipment that mounts the LEDs.
· When inspecting the final products in which LEDs were assembled, it is recommended to check
whether the assembled LEDs are damaged by static electricity or not.
It is easy to find
static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended).
· Damaged LEDs will show some unusual characteristics such as the leak current remarkably
increases, the forward voltage becomes lower, or the LEDs do not light at the low current.
Criteria : (VF > 2.0V at IF=0.5mA)
(7) Others
· NSSW061A complies with RoHS Directive.
· It is requested to avoid any stress added to the resin portion while it is heated.
· It is requested to avoid any friction by sharp metal nail etc, to the resin portion.
· Care must be taken to ensure that the reverse voltage will not exceed the absolute maximum rating
when using the LEDs with matrix drive.
· The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent
looking directly at the LEDs with unaided eyes for more than a few seconds.
· Flashing lights have been known to cause discomfort in people; you can prevent this by taking
precautions during use. Also, people should be cautious when using equipment that has had LEDs
incorporated into it.
· The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such
as office equipment, communications equipment, measurement instruments and household appliances).
Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality
and reliability are required, particularly when the failure or malfunction of the LEDs may directly
jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor
control systems, automobiles, traffic control equipment, life support systems and safety devices).
· User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written
consent from Nichia.
When defective LEDs are found, the User shall inform Nichia directly before
disassembling or analysis.
· The formal specifications must be exchanged and signed by both parties before large volume purchase begins.
· The appearance and specifications of the product may be modified for improvement without notice.
-7-
Nichia STSE-CC6048A
<Cat.No.060417>
ICI Chromaticity Diagram
0.9
520
530
0.8
540
510
550
0.7
560
0.6
570
500
0.5
580
y
590
0.4
600
610
620
a52
a65 a62
a55
a66
u15
a56
u25
u16
u12 u22 u26
0.3 490
0.2
630
480
0.1
470
460
0
0
0.1
0.2
0.3
0.4
x
½ Color Coordinates Measurement allowance is ± 0.01.
-8-
0.5
0.6
0.7
0.8
50
20
10
5
1
2.0 2.5 3.0 3.5 4.0 4.5 5.0
Forward Voltage VF (V)
3.0
2.5
2.0
1.5
1.0
0.5
0
0
20 40 60 80 100 120
Forward Current IFP (mA)
Ambient Temperature vs.
Forward Voltage
Ambient Temperature vs.
Relative Luminosity
5.0
2.0
4.6
4.2
IFP=60mA
IFP=20mA
IFP=5mA
3.8
3.4
3.0
2.6
2.2
-40 -20 0 20 40 60 80 100
Ambient Temperature Ta (°C)
Relative Luminosity (a.u.)
-9Forward Voltage VF (V)
Ta=25°C
3.5
IFP=20mA
1.0
0.5
0.2
-40 -20 0 20 40 60 80 100
Ambient Temperature Ta (°C)
Allowable Forward Current IFP (mA)
Relative Luminosity (a.u.)
Forward Current IFP (mA)
Ta=25°C
200
Ta=25°C
100
50
35
20
10
1
5 10 20
50 100
Duty Ratio (%)
Ambient Temperature vs.
Allowable Forward Current
Allowable Forward Current IF (mA)
4.0
200
100
Duty Ratio vs.
Allowable Forward Current
Forward Current vs.
Relative Luminosity
Forward Voltage vs.
Forward Current
50
40
30
20
10
8.5
0
0
20
40
60
80 100
Ambient Temperature Ta (°C)
NICHIA CORPORATION
NSSW061A
Title
CHARACTERISTICS
No.
060407649771
Nichia STSE-CC6048A
<Cat.No.060417>
Model
Forward Current vs.
Chromaticity Coordinate
Ta=25°C
0.27
1mA
5mA
20mA
50mA
100mA
y
0.26
0.25
0.24
0.23
0.25 0.26 0.27 0.28 0.29 0.30
Relative Emission Intensity (a.u.)
0.28
Spectrum
x
Ambient Temperature vs.
Chromaticity Coordinate
0.8
0.6
0.4
0.2
0
350
450
550
650
Wavelength λ (nm)
-10-
-30°C
0°C
y
25°C
0.25
50°C
85°C
0.23
0.25 0.26 0.27 0.28 0.29 0.30
x
Relative Luminosity (a.u.)
IFP=20mA
750
Y
0°
1.0
0.26
0.24
Ta=25°C
IF=20mA
1.0
Directivity
0.28
0.27
1.2
X
10° 20°
X
30°
Y
40°
50°
60°
0.5
Ta=25°C
IFP=20mA
X-X
Y-Y
0
90°
60°
30°
Radiation Angle
70°
80°
0°
0.5
NICHIA CORPORATION
NSSW061A
Title
CHARACTERISTICS
No.
060407649781
Nichia STSE-CC6048A
<Cat.No.060417>
Model
90°
1.0
Cathode mark
2.8
(1.6)
Anode
(0.35)
Cathode
. 1)
(1.35)
(1.55)
(2.45)
(R
0
0.4 ± 0.07
0.2 ± 0.07
.07
±0
.88
R0
(0.55)
0.5 ± 0.05
1.32
0.37
-11-
(0.94)
0.94
1.88
MATERIALS
PACKAGE
ENCAPSULATING RESIN
ELECTRODES
LENS
Glass Fabric Based-Epoxy Resin
Resin (with Diffused + Phosphor)
Ag Plating Copper Alloy
Resin (Diffused)
A
(NOTE)
The LED may have flash/flange which exceeds
the tolerance of this print.
½½ The gap between the center of the lens and the center
of electrodes should be kept within 0.15mm.
½
Model
NICHIA CORPORATION
Title
No.
NSSW061x
OUTLINE DIMENSIONS
060330649832
Unit
mm
20/1
Scale
Allow
±0.1
Nichia STSE-CC6048A
<Cat.No.060417>
K
ITEM
4±0.1
φ 1+0.2
-0
1.13±0.05
(1.6)
0.65±0.05
φ 180+0
-3
11.4±1
9±0.3
φ 60+1
-0
φ2
1 ±0.8
3.1±0.1
(2.75)
3.5±0.05
Cathode mark
(1.8)
2±0.05
Reel part
0.2±0.05
8+0.3
- 0.1
φ
4±0.1
1.5+0.1
-0
1.75±0.1
Taping part
±0.2
φ 13
Label
WHITE LED
TYPE NSSW061AT
LOT XXXXXX-U„
QTY
pcs
Reel End of tape
LEDs mounting part
No LEDs
No LEDs
-12Top cover
tape
Pull direction
Embossed carrier tape
Reel Lead Min.160mm (No LEDs)
Reel Lead Min.100mm
(No LEDs )
Reel Lead Min.400mm
Model
Taping is based on the JIS C 0806 : Packaging of Electronic
Components on Continuous Tapes.
NICHIA CORPORATION
Title
No.
NSSW061AT
TAPING DIMENSIONS
060215649851
Unit
mm
Scale
Allow
Nichia STSE-CC6048A
<Cat.No.060417>
5,000pcs/Reel
Nichia STSE-CC6048A
<Cat.No.060417>
The reel and moisture absorbent material are put in the moisture proof foil bag
and then heat sealed.
Reel
Label
NICHIA
Seal
WHITE LED
TYPE
LOT
QTY
NSSW061xT
xxxxxx-U„
PCS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Moisture
absorbent material
Moisture proof foil bag
The box is partitioned with the
cardboard.
Label
NICHIA
Nichia
WHITE LED
LED
TYPE
RANK
QTY
NSSW061xT
U„
PCS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Packing unit
Moisture proof foil bag
Cardboard box
Cardboard box S
Cardboard box M
Cardboard box L
Reel/bag
1reel
Quantity/bag (pcs)
5,000 MAX.
Dimensions (mm)
291¯237¯120¯8t
259¯247¯243¯5t
444¯262¯259¯8t
Reel/box
7reel MAX.
15reel MAX.
30reel MAX.
Model
NICHIA CORPORATION
-13-
Quantity/box (pcs)
35,000 MAX.
75,000 MAX.
150,000 MAX.
NSSW061xT
Title
PACKING
No.
060215545032