ELECTRIC DOUBLE LAYER CAPACITORS "EVerCAP " JC Snap-in Terminal Type series Excellent in voltage holding property. Suitable for quick charge and discharge. Wild temperature range (– 25°C ~ + 60°C). Adapted to the RoHS directive (2002/95/EC). Specifications Item Performance Characteristics Category Temperature Range – 25 ~ +60°C Rated Voltage Range 2.5V Rated Capacitance Range 15 ~ 150F Capacitance Tolerance ± 20% (20°C) Leakage Current 0.5C (mA) [ C : Rated Capacitance(F) ] ( After 30 minutes' application of rated voltage, 2.5V) Stability at Low Temperature Capacitance ( – 25°C) / Capacitance ( +20°C) ×100 ESR, DCR* Refer to the list below (20°C). * DC internal resistance Endurance After an application of DC voltage for 2000 hours at 60°C, capacitors meet the characteristic requirements listed at right. See Note 70% After storing the capacitors under no load at 60°C for 2000 hours, they will meet the characteristic requirements listed at right. Shelf Life Marking Capacitance change Within ±30% of initial value ESR 300% or less of initial specified value Leakage current Initial specified value or less Capacitance change Within ±30% of initial value ESR 300% or less of initial specified value Leakage current Initial specified value or less Printed with white color letter on black sleeve. Drawing Type numbering system (Example : 2.5V 120F) Polarity bar Sleeve (P.E.T.) 1 2 3 4 5 6 7 8 9 10 11 12 f D +1MAX. J JC 0E 127 MEL C 10 L±2 Pressure relief vent Configuration Capacitance tolerance (±20%) Rated Capacitance (120F) Rated voltage (2.5V) Series name Type 4.0±0.5 0.8 +0.2 -0.1 .2 +0 0.8 -0.1 4.0± 0.5 2.5 10± 0.1 2-2 f ±0.1 Case dia. code fD Code 22 Z 25 A 30 B 35 C 1.5 +0.2 -0.1 (Terminal dimensions) (PC board hole dimensions) Dimensions Rated Voltage ( code ) 2.5V (0E) Cap. (F) Cap. code ESR(mΩ) DCR(mΩ) (at 1kHz ) φ 22 (Z) 22 × 20 15 156 120 500 18 186 120 400 22 226 90 300 27 276 90 250 33 336 80 200 39 396 80 200 22 × 35 47 476 70 160 22 × 40 56 566 70 140 68 686 60 110 82 826 60 100 100 107 50 90 120 127 50 70 150 157 40 60 Case size φ D × L (mm) φ 25 (A) φ 30 (B) φ 35 (C) 25 × 20 30 × 20 22 × 30 30 × 20 25 × 30 35 × 20 25 × 30 35 × 20 Note : To calculate capacitance, the capacitor must be charged at the rated voltage of 2.5V for 30 minutes. Measure the time of duration ∆T (sec.) it takes go from 2V to 1V when a constant current discharge of i (A) = 0.01 × nominal capacitance is carried out. It is then possible to calculate capacitance based on the calculation provided below. Capacitance (F) = I × ∆T 25 × 35 25 × 40 30 × 30 25 × 50 30 × 40 35 × 30 35 × 35 30 × 50 35 × 40 35 × 50 CAT.8100V