HD-LINX ™ GS1540 HDTV Serial Digital Non-Equalizing Receiver DATA SHEET DESCRIPTION • SMPTE 292M compliant The GS1540 is a high performance integrated Receiver designed for HDTV component signals, conforming to the SMPTE 292M standard. The GS1540 includes adjustmentfree clock and data recovery, and 1:20 serial to parallel conversion. • 1.485 and 1.485/1.001Gb/s operation • integrated adjustment-free reclocker • 1:20 serial to parallel conversion • selectable reclocked serial output The Clock and Data Recovery stage was designed to automatically recover the embedded clock signal and re-time the data from SMPTE 292M compliant digital video signals. There is also a selectable reclocked serial data buffer output and the ability to bypass the reclocker stage. • reclocker BYPASS capability • LOCK detect • input jitter indicator (IJI) • 20 bit output A unique feature, Input Jitter Indicator (IJI), is included for robust system design. This feature is used to indicate excessive input jitter before the chip mutes the outputs. • 74.25MHz or 74.25/1.001MHz clock output • Pb-free and Green • single +5.0V power supply • minimal component count for HD SDI receive solutions The Serial to Parallel conversion stage provides 1:20 S/P conversion. APPLICATIONS The GS1540 uses the GO1515 external VCO connected to the internal PLL circuitry to achieve ultra low noise PLL performance. SMPTE 292M Serial Digital Interfaces for Production Switchers, Master Control Switchers, NLE's, and VTR's. ORDERING INFORMATION PART NUMBER PACKAGE TEMPERATURE Pb-FREE AND GREEN GS1540-CQR 128 pin MQFP 0°C to 70°C No GS1540-CQRE3 128 pin MQFP 0°C to 70°C Yes BUFFER1 DDI (opt) DDI_VTT DDI DDOint DDOint RECLOCKER CORE DATA_OUT[19:0] S/P CONVERTER PCLK_OUT BUFFER DDO DDO DDO_EN SIMPLIFIED BLOCK DIAGRAM Revision Date: June 2004 Document No. 522 - 27 - 03 GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: [email protected] www.gennum.com GS1540 FEATURES LBCONT GO1515 LFA LFS LFS PLCAP PLCAP IJI VCO CHARGE PUMP PHASE LOCK LOGIC PLL_LOCK GS1540 PHASE DETECTOR PCLK_OUT S/P CONVERTER CORE DATA_OUT[19:0] MUTE BUFFER BYPASS MUX BUFFER DDI (opt) DDI_VTT DDO DDO DDI RECLOCKER CORE BYPASS DDO_EN FUNCTIONAL BLOCK DIAGRAM ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise indicated. PARAMETER VALUE Supply Voltage (VS) Input Voltage Range (any input) Operating Temperature Range Storage Temperature Range 5.5V VEE – 0.5 < VIN < VCC+ 0.5 0°C ≤ TA ≤ 70°C -40°C ≤ TS ≤ 150°C Power Dissipation (VCC = 5.25V) 1.85W Lead Temperature (soldering 10 seconds) 260°C Input ESD Voltage 1000V Junction Temperature 125°C 2 of 17 GENNUM CORPORATION 522 - 27 - 03 DC ELECTRICAL CHARACTERISTICS VCC = 5V, VEE = 0V, TA = 0°C to 70°C unless otherwise shown, Data Rate = 1.485Gb/s. PARAMETER CONDITIONS SYMBOL MIN TYP MAX UNITS TEST LEVEL Operating range VCC 4.75 5.00 5.25 V 3 Power Consumption VCC = 5; TA = 25°c PD - 1050 - mW 5 Supply Current VCC = 5 IS - 180 - mA 1 VCM 3.4 3.9 4.30 V 5 3.7 4.0 4.2 V 1 VSID 100 - 800 mV 3 VCM 2.5+VSID/2 - VCC-VSID/2 V 3 Output CM Voltage (DDO, DDO) Input DC Voltage (DDI, DDI) Serial Inputs (DDI, DDI) internal bias voltage Differential mode TA = 25°C Common mode TA = 25°C High Level Input Voltage (BYPASS) VCC = 5, TA = 25°C VIH 2.0 - - V 3 Low Level Input Voltage (BYPASS) VCC = 5, TA = 25°C VIL - - 0.8 V 3 High Level Output Voltage VCC = 5, VOH 2.4 - 3.0 V 1 (D[19:0], PCLK) ISOURCE =1.0mA Low Level Output Voltage VCC = 5, VOL - - 0.4 V 1 (D[19:0], PCLK) ISINK = 1.0mA High Level Output Voltage (PLL_LOCK) VCC = 5, VOH 2.4 3.0 - V 1 ISOURCE = 200µA Low Level Output Voltage VCC = 5, VOL - - 0.4 V 1 (PLL_LOCK) ISINK = 500µA TEST LEVELS 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1,2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. 3 of 17 GENNUM CORPORATION 522 - 27 - 03 GS1540 Positive Supply Voltage AC ELECTRICAL CHARACTERISTICS - RECLOCKER STAGE VCC = 5V, TA = 25°C PARAMETER Serial Input – Data Rate CONDITIONS SYMBOL MIN TYP MAX UNITS TEST LEVEL BRSDI 1.485/1.001 1.485 - Gb/s 3 SMPTE 292M Sinewave Modulation (p – p) JTOL - 0.6 - UI 9 Phase Lock Time - Asynchronous Loop bandwidth approximately 1.4MHz @ 0.2 UI input jitter modulation (LBCONT floating). TALOCK - 120 145 ms 7 Phase Lock Time - Synchronous Loop bandwidth approximately 1.4MHz @ 0.2 UI input jitter modulation (LBCONT floating). TSLOCK - 2 3.2 µs 7 Carrier Detect Time Loop bandwidth approximately 1.4MHz @ 0.2 UI input jitter modulation (LBCONT floating). - 12 14 ms 7 Phase Lock/Unlock Time Loop bandwidth approximately 1.4MHz @ 0.2 UI input jitter modulation (LBCONT floating). 80 - - µs 7 VDDO 355 400 480 mV 1 tR-DDO, tF- - 160 - ps 7 - 30 - ps 7 (1nF PLCAP) Digital Data Output (DDO) – Signal Swing Digital Data Output (DDO) - DDO Rise and Fall Time Digital Data Output (DDO) – Rise and Fall Time Mismatch Digital Data Output (DDO) – Intrinsic Jitter Loop bandwidth (RMS Jitter for clean PRN 223 – 1 input on DDI/DDI inputs) tIJ - 10 - ps 9 @ 0.2UI jitter modulation 1.2 1.4 1.5 - MHz 7 - - 0.1 dB 7 LBCONT floating Jitter peaking 4 of 17 GENNUM CORPORATION 522 - 27 - 03 GS1540 Serial Input – Jitter Tolerance AC ELECTRICAL CHARACTERISTICS - SERIAL TO PARALLEL STAGE VCC = 5V, TA = 25°C PARAMETER Parallel Output Clock Frequency CONDITIONS SYMBOL MIN TYP MAX UNITS TEST LEVEL SMPTE 292M PCLK_OUT 74.25/1.001 74.25 - MHz 3 15pF load tPWL 7 - 6.1 ns 7 Clock Pulse Width High 15pF load tPWH 6 - 6.4 ns 7 Output signal Rise/Fall time 15pF load tr, tf - 2.70 3.60 ns 7 Output Signal Rise/Fall Time Matching 15pF load trfm - 1.00 1.60 ns 7 Output Setup Time 15pF load tOD 5 5.5 - ns 7 Output Hold Time 15pF load tOH 6.2 7.1 - ns 7 GS1540 Clock Pulse Width Low TEST LEVELS 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1,2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. 5 of 17 GENNUM CORPORATION 522 - 27 - 03 NC 65 38 NC NC 66 37 NC NC 67 36 PCLK_VEE NC 68 35 PCLK_VCC NC 69 34 PCLK_OUT NC 70 33 SP_VEE NC 71 32 SP_VEE LFA_VCC 72 31 SP_VCC LFA 73 30 SP_VCC LBCONT 74 29 NC LFA_VEE 75 28 NC DFT_VEE 76 27 NC NC 77 26 NC NC 78 25 NC DM 79 24 NC DM 80 23 NC LFS 81 22 NC NC 82 21 DDO_VCC NC 83 20 DDO_EN NC 84 19 DDO_VEE LFS 85 18 DDO IJI 86 17 DDO NC 87 16 NC NC 88 15 NC VCO 89 14 NC NC 90 13 NC VCO 91 12 NC NC 92 11 NC PLCAP 93 10 NC NC 94 9 NC NC 95 8 NC PLCAP 96 7 NC NC 97 6 NC PLL_LOCK 98 5 NC NC 99 4 NC NC 100 3 NC NC 101 2 NC NC 102 1 NC NC NC BYPASS DDI_VTT NC DDI DDI PD_VCC NC PDSUB_VEE PD_VEE NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 GS1540 TOP VIEW GS1540 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 DATA_OUT[19] DATA_OUT[18] DATA_OUT[17] DATA_OUT[16] DATA_OUT[15] DATA_OUT[14] NC NC DATA_OUT[13] DATA_OUT[12] DATA_OUT[11] DATA_OUT[10] NC NC DATA_OUT[9] DATA_OUT[8] DATA_OUT[7] DATA_OUT[6] DATA_OUT[5] DATA_OUT[4] DATA_OUT[3] DATA_OUT[2] DATA_OUT[1] DATA_OUT[0] NC NC PIN CONNECTIONS 6 of 17 GENNUM CORPORATION 522 - 27 - 03 PIN DESCRIPTIONS NUMBER SYMBOL LEVEL TYPE NC No Connect. Leave these pins floating. GS1540 1, 2, 3, 4, 6, 5, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 22, 23, 24, 25, 26, 27, 28, 29, 37, 38, 39, 40, 51, 52, 57, 58, 65, 66, 67, 68, 69, 70, 71, 77, 78, 82, 83, 84, 87, 88, 90, 92, 94, 95, 97, 99, 100, 101, 102, 103, 104, 107, 111, 114, 115, 116, 117, 118, 119, 120, 121, 122, 123, 124, 125, 126, 127, 128 DESCRIPTION 17, 18 DDO, DDO ECL/PECL compatible Output Digital Data Output. Differential serial outputs. 50Ω pull up resistors are included on chip. Note that these outputs are not cable drivers. Ensure that the trace length between the GS1540 and the GS1508 Cable driver is kept to a minimum and that a PCB trace characteristic impedance of 50Ω is maintained between the GS1508 and the GS1540. 50Ω end termination is recommended. 19 DDO_VEE Power Input Negative Supply. Most negative power supply connection for serial data output stage. 20 DDO_EN Power Input Control Signal Input. Used to enable or disable the serial output stage. If a loop through function is not required, then this pin should be tied to the most positive power supply voltage. When DDO_EN is tied to the most negative power supply voltage, the DDO, DDO outputs are enabled. When DDO_EN is tied to the most positive power supply voltage, the DDO, DDO outputs are disabled. 21 DDO_VCC Power Input Positive Supply. Most positive power supply connection for serial data output stage. 30, 31 SP_VCC Power Input Positive Supply. Most positive power supply connection for serial to parallel converter stage. 32, 33 SP_VEE Power Input Negative Supply. Most negative power supply connection for the parallel output stage. 34 PCLK_OUT TTL Output 35 PCLK_VCC Power Input Positive Supply. Most positive supply connection for parallel clock output stage. 36 PCLK_VEE Power Input Negative Supply. Most negative power supply connection for parallel clock output stage. DATA_OUT[19:0] TTL Output 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 53, 54, 55, 56, 59, 60, 61, 62, 63, 64 Output Clock. The device uses PCLK_OUT for clocking the output data stream from DATA_OUT[19:0]. This clock is also used to clock the data into the GS1500 HDTV Deformatter, or GS1510 HDTV Deformatter. Parallel Data Output Bus. The device outputs a 20 bit parallel data stream running at 74.25 or 74.25/1.001MHz on DATA_OUT[19:0]. DATA_OUT[19] is the MSB and DATA_OUT[0] is the LSB. 7 of 17 GENNUM CORPORATION 522 - 27 - 03 PIN DESCRIPTIONS (Continued) NUMBER SYMBOL LEVEL TYPE DESCRIPTION 72 LFA_VCC Power Input 73 LFA Analog Output 74 LBCONT Analog Input Control Signal Input. Used to provide electronic control of Loop Bandwidth. 75 LFA_VEE Power Input Negative Supply. Loop filter most negative power supply connection. 76 DFT_VEE Power Input Most negative power supply connection - enables the jitter demodulator functionality. This pin should be connected to ground. If left floating, the DM function is disabled resulting in a current saving of 340µA. 79, 80 DM, DM Analog Output Positive Supply. Loop filter most positive power supply connection. Control Signal Output. Control voltage for GO1515 VCO. These pins must be floating for normal operation. LFS, LFS Analog Input 86 IJI Analog Output Status Signal Output. Approximates the amount of excessive jitter on the incoming DDI and DDI input. 89 VCO Analog Input Control Signal Input. Input pin is AC coupled to ground using a 50Ω transmission line. 91 VCO Analog Input Control Signal Input. Voltage controlled oscillator input. This pin is connected to the output pin of the GO1515 VCO. 81, 85 Loop Filter Connections. This pin must be connected to the GO1515 VCO output pin via a 50Ω transmission line. 93, 96 PLCAP, PLCAP Analog Input PLL_LOCK TTL Output 98 Control Signal Input. Phase lock detect time constant capacitor. Status Indicator Signal. This signal is a combination (logical AND) of the carrier detect and phase lock signals. When input is present and PLL is locked, the PLL_LOCK goes high and the outputs are valid. When the PLL_LOCK output is low the data output is muted (latched at the last state). PLL_LOCK is independent of the BYPASS signal. 105 BYPASS TTL Input Control Signal Input. Selectable input that controls whether the input signal is reclocked or passed through the chip. When BYPASS is high; the input signal is reclocked. When BYPASS is low; the input signal is passed through the chip and not reclocked. Muting does not effect bypassed signal. 106 DDI_VTT Analog Input Bias Input. Selectable input for interfacing standard ECL outputs requiring 50Ω pull down to VTT power supply for a seamless interface. See Typical Application Circuit for recommended circuit application. 108, 109 DDI, DDI Differential ECL/PECL Input Digital Data Input Signals. Digital input signals from a GS1504 Equalizer or HD crosspoint switch. Because of on chip 50Ω termination resistors, a PCB trace characteristic impedance of 50Ω is recommended. 110 PD_VCC Power 112 PDSUB_VEE Power Input Substrate Connection. Connect to phase detector’s most negative power supply. 113 PD_VEE Power Input Negative Supply. Phase detector most negative power supply connection. Positive Supply. Phase detector most positive power supply connection. 8 of 17 GENNUM CORPORATION 522 - 27 - 03 GS1540 Test Signal. Used for manufacturing test only. INPUT/OUTPUT CIRCUITS PD_VCC 5k PD_VCC 10k PLCAP GS1540 20k PLCAP 20k 100µA PD_VEE DDI 50 DDI 50 PD_VEE DDI_VTT Fig. 4 PLCAP/PLCAP Output Circuit Fig. 1 DDI/DDI Input Circuit PD_VCC 5k LFA_VCC 5k 500 LFA 10k 10k 40 40 31p 5mA VCO 100µA PD_VEE 50 LFA_VEE VCO Fig. 5 LFA Circuit Fig. 2 VCO/VCO Input Circuit LFA_VCC PD_VCC 25k 10k 10k DM DM LFS 400µA 85µA LFA_VEE DFT_VEE Fig. 6 LFS Output Circuit Fig. 3 DM/DM Output Circuit 9 of 17 GENNUM CORPORATION 522 - 27 - 03 LFA_VCC 10k PD_VCC 5k 16k 100µA + - BYPASS V = 2.4V 100µA 100µA 100µA 100µA LFA_VEE PD_VEE Fig. 7 LFS Input Circuit Fig. 10 BYPASS Circuit PD_VCC LFA_VCC 20k 10k LBCONT PLL_LOCK 5k PD_VEE LFA_VEE Fig. 8 PLL_LOCK Output Circuit Fig. 11 LBCONT Circuit PD_VCC 10k SP_VCC IJI 5k 100 D[19:0] VCC 30k A 27k SP_VEE PD_VEE Fig. 9 IJI Output Circuit Fig. 12 D[19:0] Output Circuit 10 of 17 GENNUM CORPORATION 522 - 27 - 03 GS1540 LFS DETAILED DESCRIPTION The GS1540 is a single standard receiver for serial digital HDTV signals at 1.485Gb/s and 1.485/1.001Gb/s. PCLK_VCC UNIQUE SLEW PHASE LOCK LOOP (S-PLL): PCLK 27k PCLK_VEE Fig. 13 PCLK Output Circuit PHASE (UI) 0.2 DDO_VCC DDO_EN INPUT 0.1 OUTPUT 0.0 20k SLEW PLL RESPONSE 2k 0.2 PHASE (UI) DDO_VEE Fig. 14 DDO_EN Circuit INPUT 0.1 OUTPUT 0.0 LINEAR (CONVENTIONAL) PLL RESPONSE Fig. 16 PLL Characteristics zDDO_VCC 50 50 DDO DDO Slew PLLs offer several advantages such as excellent noise immunity. Because of the infinite bandwidth for an infinitely small input jitter modulation (or jitter introduced by VCO), the loop corrects for that immediately thus the small signal noise of the VCO is cancelled. The GS1540 uses a very clean, external VCO called the GO1515 (refer to the GO1515 Data Sheet for details). In addition, the bi-level digital phase detector provides constant loop bandwidth that is predominantly independent of the data transition density. The loop bandwidth of a conventional tri-stable charge pump drops with reducing data transitions. During pathological signals, the data transition density reduces from 0.5 to 0.05, but the slew PLL’s performance essentially remains unchanged. DDO_VEE Fig. 15 Serial (DDO) Output Stage Circuit 11 of 17 GENNUM CORPORATION 522 - 27 - 03 GS1540 A unique feature of the GS1540 is the innovative slew phase lock loop (S-PLL). When a step phase change is applied to the PLL, the output phase gains constant rate of change with respect to time. This behaviour is termed slew. Figure 16 shows an example of input and output phase variation over time for slew and linear (conventional) PLLs. Since the slewing is a nonlinear behavior, the small signal analysis cannot be done in the same way as the standard PLL. However, it is still possible to plot input jitter transfer characteristics at a constant input jitter modulation. 100 DIGITAL INPUT BUFFER The input buffer is a self-biased circuit. On-chip 50Ω termination resistors provide a seamless interface for other HD-LINX™ products such as the GS1504 Adaptive Cable Equalizer. PHASE DETECTOR The phase detector portion of the slew PLL used in the GS1540 is a bi-level digital phase detector. It indicates whether the data transition occurred before or after with respect to the falling edge of the internal clock. When the phase detector is locked, the data transition edges are aligned to the falling edge of the clock. The input data is then sampled by the rising edge of the clock, as shown in Figure 17. In this manner, the allowed input jitter is 1UI p-p in an ideal situation. However, due to setup and hold time, the GS1540 typically achieves 0.5UI p-p input jitter tolerance without causing any errors in this block. When the signal is locked to the internal clock, the control output from the phase detector is refreshed at the transition of each rising edge of the data input. During this time, the phase of the clock drifts in one direction. PHASE ALIGNMENT EDGE RE-TIMING EDGE IN-PHASE CLOCK CHARGE PUMP The charge pump in a slew PLL is different from the charge pump in a linear PLL. There are two main functions of the charge pump. One function is to hold the frequency information of the input data. This information is held by CCP1, which is connected between LFS and LFS. The other capacitor, CCP2 between LFS and LFA_GND is used to remove common mode noise. Both CCP1 and CCP2 should be the same value. The second function of the charge pump is to provide a binary control voltage to the VCO depending upon the phase detector output. The output pin, LFA controls the VCO. Internally there is a 500Ω pull-up resistor, which is driven with a 100µA current called ΙP. Another analog current ΙF, with 5mA maximum drive proportional to the voltage across the CCP1, is applied at the same node. The voltage at the LFA node is VLFA_VCC - 500(ΙP+ΙF) at any time. Because of the integrator, ΙF changes very slowly whereas ΙP could change at the positive edge of the data transition as often as a clock period. In the locked position, the average voltage at the LFA (VLFA_VCC – 500(ΙP/2+ΙF) is such that VCO generates frequency ƒ, equal to the data rate clock frequency. Since ΙP is changing all the time between 0A and 100µA, there will be two levels generated at the LFA output. VCO The GO1515 is an external hybrid VCO, which has a centre frequency of 1.485GHz and is also guaranteed to provide 1.485/1.001GHz within the control voltage (3.1V – 4.65V) of the GS1540 over process, power supply and temperature. The GO1515 is a very clean frequency source and, because of the internal high Q resonator, it is an order of magnitude more immune to external noise as compared to on-chip VCOs. The VCO gain, Kƒ, is nominally 16MHz/V. The control voltage around the average LFA voltage will be 500 x ΙP/2. This will produce two frequencies off from the centre by ƒ=Kƒ x 500 x ΙP/2. 0.5UI INPUT DATA WITH JITTER LBCONT OUTPUT DATA Fig. 17 Phase Detector Characteristics During pathological signals, the amount of jitter that the phase detector will add can be calculated. By choosing the proper loop bandwidth, the amount of phase detector induced jitter can also be limited. Typically, for a 1.41MHz loop bandwidth at 0.2UI input jitter modulation, the phase detector induced jitter is about 0.015UIp-p. This is not very significant, even for the pathological signals. The LBCONT pin is used to adjust the loop bandwidth by externally changing the internal charge pump current. For maximum loop bandwidth, connect LBCONT to the most positive power supply. For medium loop bandwidth, connect LBCONT through a pull-up resistor (RPULL-UP). For low loop bandwidth, leave LBCONT floating. The formula below shows the loop bandwidth for various configurations. ( 25kΩ + R PULL – UP ) LBW = LBW NOMINAL × -----------------------------------------------------( 5kΩ + R PULL – UP ) where LBW nominal is the loop bandwidth when LBCONT is left floating. 12 of 17 GENNUM CORPORATION 522 - 27 - 03 GS1540 Because most of the PLL circuitry is digital, it is more like other digital systems which are generally more robust than their analog counterparts. Additionally, signals like DM/DM which represent the internal functionality can be generated without adding additional artifacts. Thus, system debugging is also possible with these features. The complete slew PLL is made up of several blocks including the phase detector, the charge pump and an external Voltage Controlled Oscillator (VCO). INPUT JITTER INDICATOR (IJI) Since the feed back loop has only digital circuits, the small signal analysis does not apply to the system. The effective loop bandwidth scales with the amount of input jitter modulation index. This signal indicates the amount of excessive jitter (beyond the quadrature clock window 0.5UI), which occurs beyond the quadrature clock window (see Figure 18). All the input data transitions occurring outside the quadrature clock window, will be captured and filtered by the low pass filter as mentioned in the Phase Lock section. The running time average of the ratio of the transitions inside the quadrature clock and outside the quadrature is available at the PLCAP/PLCAP pins. A signal, IJI, which is the buffered signal available at the PLCAP is provided so that loading does not effect the filter circuit. The signal at IJI is referenced with the power supply such that the factor VIJI /V CC is a constant over process and power supply for a given input jitter modulation. The IJI signal has 10kΩ output impedance. Figure 19 shows the relationship of the IJI signal with respect to the sine wave modulated input jitter. PHASE LOCK The phase lock circuit is used to determine the phase locked condition. It is done by generating a quadrature clock by delaying the in-phase clock (the clock whose falling edge is aligned to the data transition) by 166ps (0.25UI at 1.5GHz) with the tolerance of 0.05UI. When the PLL is locked, the falling edge of the in-phase clock is aligned with the data edges as shown in Figure 18. The quadrature clock is in a logic high state in the vicinity of input data transitions. The quadrature clock is sampled and latched by positive edges of the data transitions. The generated signal is low pass filtered with an RC network. The R is an on-chip 20kΩ resistor and CPL is an external capacitor (recommended value 10nF). The time constant is about 67µs, or more than a video line. PHASE ALIGNMENT EDGE P-P SINE WAVE JITTER IN UI IJI VOLTAGE 0.00 4.75 0.15 4.75 0.30 4.75 0.39 4.70 0.45 4.60 0.48 4.50 0.52 4.40 0.55 4.30 0.58 4.20 0.60 4.10 0.63 3.95 RE-TIMING EDGE IN-PHASE CLOCK 0.5UI INPUT DATA WITH JITTER 0.25UI QUADERATURE CLOCK PLCAP SIGNAL 5.0 PLCAP SIGNAL Fig. 18 PLL Circuit Principles If the signal is not locked, the data transition phase could be anywhere with respect to the internal clock or the quadrature clock. In this case, the normalized filtered sample of the quadrature clock will be 0.5. When VCO is locked to the incoming data, data will only sample the quadrature clock when it is logic high. The normalized filtered sample quadrature clock will be 1.0. We chose a threshold of 0.66 to generate the phase lock signal. Because the threshold is lower than 1, it allows jitter to be greater than 0.5UI before the phase lock circuit reads it as “not phase locked”. IJI SIGNAL (V) 4.8 4.6 4.4 4.2 4.0 3.8 3.6 0.00 0.20 0.40 0.60 0.80 INPUT JITTER (UI) Fig. 19 Input Jitter Indicator (Typical at TA = 25°C) 13 of 17 GENNUM CORPORATION 522 - 27 - 03 GS1540 LOOP BANDWIDTH OPTIMIZATION LOCK LOGIC The differential jitter demodulation (DM) signal is available at the DM and DM pins. This signal is the phase correction signal of the PLL loop, which is amplified and buffered. If the input jitter is modulated, the PLL tracks the jitter if it is within loop bandwidth. To track the input jitter, the VCO has to be adjusted by the phase detector via the charge pump. Thus, the signal which controls the VCO contains the information of the input jitter modulation. The jitter demodulation signal is only valid if the input jitter is less than 0.5UIp-p. The DM/DM signals have 10kΩ output impedance, which could be low pass filtered with appropriate capacitors to eliminate high frequency noise. DFT_VEE should be connected to GND to activate DM/DM signals. Logic is used to produce the PLL_LOCK signal which is based on the LFS signal and phase lock signal. When there is not any data input, the integrator will charge and eventually saturate at either end. By sensing the saturation of the integrator, it is determined that no data is present. If either data is not present or phase lock is low, the lock signal is made low. Logic signals are used to acquire the frequency by sweeping the integrator. Injecting a current into the summing node of the integrator achieves the sweep. The sweep is disabled once phase lock is asserted. The direction of the sweep is also changed once LFS saturates at either end. The DM signals can be used as diagnostic tools. Assume there is an HDTV SDI source, which contains excessive noise during the horizontal blanking because of the transient current flowing in the power supply. In order to discover the source of the noise, one could probe around the source board with a low frequency oscilloscope (Bandwidth < 20MHz) that is triggered with an appropriately filtered DM/DM signal. The true cause of the modulation will be synchronous and will appear as a stationary signal with respect to the DM/DM signal. Figure 20 shows an example of such a situation. An HDTV SDI signal is modulated with a modulation signal causing about 0.2UI jitter in Figure 20 (Channel 1). The GS1540 receives this signal and locks to it. Figure 20 (Channel 2) shows the DM signal. Notice the wave shape of the DM signal, which is synchronous to the modulating signal. The DM/DM signal could also be used to compare the output jitter of the HDTV signal source. BYPASS The BYPASS block bypasses the reclocked/mute path of the data whenever a logic low input is applied to the BYPASS input. In the bypass mode, the mute does not have any effect on the outputs. Also, the internal PLL still locks to a valid HDTV signal and shows PLL_LOCK. SERIAL OUTPUT STAGE The serial output (DDO, DDO) signals have a nominal voltage of 400mVpp differential, or 200mVpp single ended when terminated with 50Ω. DDO_EN The DDO_EN enables or disables the serial output driver. To disable the driver, tie DDO_EN to VCC. To enable the driver, tie DDO_EN to VEE. When disabled, the supply current is reduced by approximately 10mA. SERIAL TO PARALLEL CONVERTER The high-speed serial to parallel converter accepts differential clock and data signals from the reclocker core. The S/P core converts this serial output into a 20-bit wide data stream (D[19:0]). Note that this data stream is not word aligned or descrambled. It also provides a parallel clock, which is 1/20th the serial clock rate (PCLK_OUT). The outputs of the S/P block are TTL compatible. When the PLL loses lock, the parallel clock continues to freewheel. The parallel clock and data outputs were designed for seamless interfaces to the GS1500 and GS1510 deformatters. Fig. 20 Jitter Demodulation Signal 14 of 17 GENNUM CORPORATION 522 - 27 - 03 GS1540 JITTER DEMODULATION (DM) J6 Note that these outputs are not cable drivers J5 4µ7 C32 All resistors in ohms, all capacitors in farads, unless otherwise shown. 4µ7 C33 10n BYPASS 123 nc 124 nc 125 nc 126 nc 127 nc 128 nc 116 nc 117 nc 118 nc 119 nc 120 nc 121 nc 122 nc 106 DDI_V TT 107 nc 108 DDI 109 DDI 110 PD_V CC 111 nc 112 PDSUB_VEE 113 PD_V EE 114 nc 115 nc 10n VCO POWER PLANE 2 nc 3 nc C25 103 nc 104 nc 105 BYPASS nc 102 1 nc nc 99 98 PLL_LOCK nc 97 4 nc 5 nc VCC nc 101 nc 100 PLL_LOCK PLCAP PLCAP 96 nc 95 nc 94 93 VCO 91 0Ω R116 VCO 92 nc 6 nc 7 nc 8 nc 9 nc 10 nc 11 nc 10n C26 100n C59 10µ C60 100n C61 10µ C64 nc 90 VCO 89 12 nc 13 nc C27 1µ L11 LFS 1µ + 4µ7 C23 4µ7 C24 + VCC 0Ω V C35 CC 10n L8 J4 J7 100n 10µ C50 C51 10µ 100n C49 C52 MAIN POWER PLANE DIGITAL POWER PLANE GS1540 nc IJI 86 LFS 85 84 nc 17 DDO 18 DDO 19 DDO_V EE C34 + 25 nc 26 nc nc 88 nc 87 14 nc 15 nc 16 nc C28 + DDO_EN DDO_EN 21 DDO_VCC 22 nc 27 nc nc 23 LFA_VEE 75 LBCONT 74 VCC VCC 28 nc 29 nc nc 83 nc 82 81 20 DM 80 79 DM nc 78 nc 77 DFT_VEE 76 24 LFA LFA 73 LFA_VCC 72 nc 71 VCC SP_VCC nc 70 nc 69 0Ω R19 nc 68 nc 67 VCC 33 SP_V EE 34 PCLK_OUT 35 PCLK_V CC 36 PCLK_V EE 31 SP_V CC 32 SP_V EE VCC 30 nc 66 nc 65 37 nc 38 nc GENNUM CORPORATION VCC 10n 10n 10n 60 61 41 42 D0 nc 40 nc 39 D1 D2 43 nc 51 D9 50 49 D8 48 D7 47 D6 46 D5 45 D4 D3 44 D10 53 nc 52 56 D13 D12 55 D11 54 59 D14 nc 58 nc 57 D15 D16 62 D19 64 D18 63 D17 10n C65 PCLK D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 (110/112) (19/21) (30-31/32-33) (35/36) C31 C30 C29 VCC GS1540 VCC TYPICAL APPLICATION CIRCUIT 15 of 17 522 - 27 - 03 TYPICAL APPLICATION CIRCUIT (continued) GO1515 VCO POWER CONNECT LFA VCC C43 C41 VCC + 100n 10µ C42 + C44 VCTR 1 2 GND 6 GND GND 100n 8 GS1540 LOCK DETECT VCC 7 nc VCC 3 U2 GND GO1515 5 O/P 4 GS1540 10µ R27 R26 PLL_LOCK VCO Q3 LED3 150 22k GS1540 CONFIGURATION JUMPERS VCC BYPASS VCC DDO_EN All resistors in ohms, all capacitors in farads, unless otherwise shown. APPLICATION INFORMATION Please refer to the EBHDRX evaluation board documentation for more detailed application and circuit information on using the GS1540 with the GS1500 and GS1510 Deformatters. 16 of 17 GENNUM CORPORATION 522 - 27 - 03 PACKAGE DIMENSIONS 23.20 ±0.25 20.0 ±0.10 18.50 REF GS1540 12 TYP 12.50 REF 0.75 MIN 17.20 ±0.25 0 -7 14.0 ±0.10 0.30 MAX RADIUS 0-7 0.13 MIN. RADIUS 0.88 ±0.15 1.6 REF 3.00 MAX 0.50 BSC 0.27 ±0.08 128 pin MQFP All dimensions are in millimetres. 2.80 ±0.25 CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION DOCUMENT IDENTIFICATION REVISION NOTES: Added lead-free and green information. For latest product information, visit www.gennum.com PRELIMINARY DATA SHEET The product is in a preproduction phase and specifications are subject to change without notice. GENNUM CORPORATION MAILING ADDRESS: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 SHIPPING ADDRESS: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F 6-14-1, Nishi Shinjuku Shinjuku-ku, Tokyo 160-0023 Japan Tel: +81 (03) 3349-5501 Fax: +81 (03) 3349-5505 GENNUM UK LIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523 Gennum Corporation assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. © Copyright May 2000 Gennum Corporation. All rights reserved. Printed in Canada. 17 of 17 522 - 27 - 03