HI-8200H, HI-8201H, HI-8202H Quad 10 Ohm +/-12V outside-the-rails Analog Switch with High Operating Temperature August 2013 GENERAL DESCRIPTION The HI-8200H family are quad analog CMOS switches fabricated with Silicon-on-Insulator (SOI) technology for latch-up free operation and maximum switch isolation. They are optimized for use in high temperature avionics applications. The devices are capable of operating at extended temperature ranges of -55°C to 175°C for plastic packages and -55°C to 200°C for the ceramic CERDIP-16 package. High voltage gate drive is entirely created on-chip enabling +/-12V switching range from a single 3.3V or 5V supply. These switches are ideally suited for applications demanding low switch leakage when the power pins are 0V. FEATURES · Extended Temperature Ranges ·-55°C to 175°C (plastic packages) ·-55°C to 200°C (ceramic CERDIP-16 package) · CMOS analog switches with up to +/-12V switching range from a single 3.3V or 5V supply · Low RON: 10W max at 25°C · Robust CMOS Silicon-on-Insulator (SOI) technology · Switch nodes are open-circuit when chip is powered down · SOI switch isolation with 1nA typical Off leakage · ESD protection > 4KV HBM At 25°C and with VDD from 3.0V to 5.5V, the switch resistance (RON) is typically 8W. RON is independent of VDD. In a switching range of -5V to +5V, the maximum deviation of RON from flat is less than 5%. These switches conduct equally well in either direction. Power down and Off state leakages are less than 10nA maximum. Charge injection is less than 10pC. Switching times are typically 180ns to the On state and 60ns to the Off state. The onboard charge pump allows an On/Off cycle time of 5KHz for all four switches simultaneously before the switching range becomes restricted. The HI-8200H provides four each normally open switches when the switch control inputs are low. The HI-8201H provides four each normally closed switches when the switch control inputs are low. The HI-8202H provides a combination of two normally closed and two normally open switches. · Fast switching time with break-before-make · Low power PIN CONFIGURATIONS (Top Views) IN1 1 20 IN2 S1A 2 19 S2A -3 18 - S1B 4 17 S2B V- 5 16 V+ GND 6 15 VLOGIC S4B 7 14 S3B -8 13 - S4A 9 12 S3A IN4 10 11 IN3 APPLICATIONS HI-8200PSHF 20-Pin TSSOP package · Down-hole drilling and oil exploration · High temperature avionics · Data bus isolation · Sample-and-Hold circuits · Test Equipment · Communications Systems (DS8200H Rev. New) PRODUCT OPTIONS PART TYPE IN1 HI-8200H 0 1 HI-8201H 0 1 HI-8202H 0 1 HOLT INTEGRATED CIRCUITS www.holtic.com Switch 1 Open Closed Closed Open Open Closed IN2 0 1 0 1 0 1 Switch 2 Open Closed Closed Open Closed Open IN3 0 1 0 1 0 1 Switch 3 Open Closed Closed Open Closed Open IN4 0 1 0 1 0 1 Switch 4 Open Closed Closed Open Open Closed 08/13 HI-8200H, HI-8201H, HI-8202H PIN DESCRIPTIONS SIGNAL FUNCTION IN1 S1A S1B VGND S4B S4A IN4 IN3 S3A S3B VLOGIC V+ S2B S2A IN2 Logic Input Switch Node Switch Node CAP Supply Switch Node Switch Node Logic Input Logic Input Switch Node Switch Node Supply CAP + Switch Node Switch Node Logic input DESCRIPTION HI-8200H and HI-8202H are normally Open when input Low Switch 1 Node Switch 1 Node Bulk storage capacitor. Add 0.1uF ceramic capacitor to GND. (20V or higher). Reference Ground Switch 4 Node Switch 4 Node HI-8200H and HI-8202H are normally Open when input Low HI-8201H and HI-8202H are normally Closed when input Low Switch 3 Node Switch 3 Node 3.3V or 5.0V Logic supply Bulk storage capacitor. Add 0.1uF ceramic capacitor to GND. (20V or higher). Switch 2 Node Switch 2 Node HI-8201H and HI-8202H are normally Closed when input Low NOTE: V+ and V- pins are only to be used for connection of bulk storage capacitors and MUST NOT be loaded. 35W 30W T = -55C T = +200C 25W T = +125C 20W T = +25C 15W 10W 5W -18V -12V -6V 0V VSWITCH 6V 12V 18V Typical RON as a function of VSWITCH and Temperature (10mA switch current, VSUPPLY = +3.3V) HOLT INTEGRATED CIRCUITS 2 HI-8200H, HI-8201H, HI-8202H ABSOLUTE MAXIMUM RATINGS (Voltages referenced to GND = 0V) Supply Voltage, VLOGIC .........................................................................7.0V Operating Temperature Range: (Plastic) ........................ -55°C to +175°C (Ceramic) ...................... -55°C to +200°C Switch Current (either direction, DC): .................................................20mA Peak Switch Current (1 ms pulse, 10% duty cycle max.)..................100mA Digital Input Voltage (IN1-4):.....................................-0.3V to VLOGIC + 0.3V Storage Temperature Range: ......................................-65°C to +150°C Reflow Soldering Temperature: .......................................... +260°C Max. NOTE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS VLOGIC = 3.3V or 5.0V, GND = 0V. Operating temperature range (unless otherwise noted). PARAMETER SYMBOL CONDITIONS FIGURE MIN TYP MAX UNIT RON 12V > Vs > -12V 1 6 8 10 W |ISWLEAK| Switch voltage ± 12V, 125°C Switch voltage ± 12V, 200°C 2 1 10 2 nA µA SWITCH PARAMETERS Switch Resistance, 25°C, 10mA Leakage - (open circuit and power down) LOGIC INPUTS Input High Voltage VIH Input Low Voltage VIL Input Current IIH IIL 75% V 25% V 0.5 2 µA µA µA µA 5.5 V inputs static VLogic = 3.3V Vlogic = 5.0V 1.0 2.5 mA mA any load 5 Khz 80K Ohm pulldown VLogic = 3.3V Vlogic = 5.0V 125°C 200°C 45 65 SUPPLY VLogic Operating Range VDD VLogic Operating Current IDD 3.0 DYNAMIC PARAMETERS Max Vin On/Off cycling fcycle Turn On Time TON 3 180 250 ns Turn Off time TOFF 3 80 150 ns Break-Before-Make Time TD 4 Charge Injection Q VS=0V, RS=0W, 25°C Off Isolation RR f = 1 MHz, 25°C Crosstalk 40 80 ns 5 -20 pC 6 65 dB CR f = 1 MHz, 25°C 7 90 dB Capacitance COFF CON Switch Off, 25°C Switch On, 25°C 8 9 15 60 pF pF Charge Pump Power On Tvon V+ and V- = +/-14.5V VLogic = 5.0V 10 HOLT INTEGRATED CIRCUITS 3 10 ms HI-8200H, HI-8201H, HI-8202H TEST CIRCUITS IDS V1 SA VS + - RON = V1/IDS + - VS Figure 1 - On Resistance +3.3V 0.1µF 0.1µF (20V) V+ SA VD + - Figure 2 - Off Leakage VIN (HI-8201) VLOGIC ID(OFF) SB A IS(OFF) SA A SB 50% 50% 50% 50% VIN (HI-8200) SB VOUT IN VS GND + - V- 35pF 90% 300W 50% VOUT 0.1µF (20V) t ON t OFF Figure 3. Switching Times 0.1µF +3.3V 0.1µF (20V) 3.3V VLOGIC VIN V+ 50% 50% 0V VS1 VS2 S1A S1B S2A S2B IN VOUT1 VOUT2 35pF GND V- 35pF 90% 50% VOUT1 300W 300W 90% VOUT2 50% 0.1µF (20V) tD Figure 4. Break-Before-Make Time Delay (HI-8202H) HOLT INTEGRATED CIRCUITS 4 tD HI-8200H, HI-8201H, HI-8202H +3.3V VLOGIC RS 0.1µF (20V) V+ SA SB VOUT VIN IN VS GND + - CL 10nF V- DVOUT VOUT 0.1µF (20V) QINJ = CL x DVOUT Figure 5. Charge Injection 0.1µF 0.1µF +3.3V +3.3V 0.1µF (20V) 0.1µF (20V) V+ VLOGIC VLOGIC SA1 V+ SA SB SB1 50W IN1 VOUT VS IN IN2 GND 50W V- VS SB2 VOUT 0.1µF (20V) 50W SA2 GND NC V- 0.1µF (20V) Figure 6 - Off Isolation Figure 7 - Channel-to-Channel Crosstalk 0.1µF +3.3V VLOGIC 0.1µF (20V) V+ SA Capacitance Meter f=1MHz 0.1µF VLOGIC SB SA Capacitance Meter f=1MHz IN GND +3.3V V- 0.1µF (20V) V+ SB IN GND V- 0.1µF (20V) 0.1µF (20V) Figure 8 - Off Capacitance Figure 9 - On Capacitance HOLT INTEGRATED CIRCUITS 5 VS HI-8200H, HI-8201H, HI-8202H 15V +3.3V 0.1µF (20V) 10V VLOGIC V+ 5V T=0 0V -5V GND +3.3V +- V- -10V -15V 0.1µF (20V) T=0 2ms Figure 10. Charge Pump Power On Additional package configurations IN1 1 16 IN2 S1A 2 15 S2A S1B 3 14 S2B V- 4 GND 5 13 V+ 12 VLOGIC S4B 6 11 S3B S4A 7 10 S3A IN4 8 9 IN3 HI-8200CRH 16-Pin CERDIP package HOLT INTEGRATED CIRCUITS 6 4ms 6ms Time 8ms 10ms HI-8200H, HI-8201H, HI-8202H ORDERING INFORMATION HI - 820x PS H F PART NUMBER F PART NUMBER PS PART NUMBER LEAD FINISH 100% Matte Tin (Pb-free, RoHS compliant) PACKAGE DESCRIPTION o o 20 PIN PLASTIC TSSOP (20HS): -55 C to +175 C. FUNCTION 8200 QUAD SWITCH, NORMALLY OPEN 8201 QUAD SWITCH, NORMALLY CLOSED 8202 QUAD SWITCH, TWO NORMALLY OPEN, TWO NORMALLY CLOSED HI - 820x CR H PART NUMBER CR PART NUMBER PACKAGE DESCRIPTION o o 16 PIN CERDIP (16D) not available Pb-free: -55 C to +200 C. FUNCTION 8200 QUAD SWITCH, NORMALLY OPEN 8201 QUAD SWITCH, NORMALLY CLOSED 8202 QUAD SWITCH, TWO NORMALLY OPEN, TWO NORMALLY CLOSED HOLT INTEGRATED CIRCUITS 7 HI-8200H, HI-8201H, HI-8202H REVISION HISTORY P/N Rev DS8200H New Date 08/27/13 Description of Change Initial release HOLT INTEGRATED CIRCUITS 8 HI-8200H PACKAGE DIMENSIONS inches (millimeters) 20-PIN PLASTIC TSSOP Package Type: 20HS .2555 ± .0035 (6.500 ± .100) .252 ± .006 (6.400 ± .150) .006 ± .002 (.145 ± .055) .173 ± .004 (4.400 ± .100) Pin 1 See Detail A .0095 ± .0025 (.245 ± .055) .036 ± .005 (.925 ± .125) .026 BSC (.650) 0° to 8° .004 ± .002 (.100 ± .050) .018 - .029 (.450 - .750) BSC = “Basic Spacing between Centers” is theoretical true position dimension and has no tolerance. (JEDEC Standard 95) Detail A inches (millimeters) 16-PIN CERDIP Package Type: 16D .050 max (1.27 max) .790 max (20.006 max) .005 min (.127 min) .288 ±.005 (7.315 ±.125) .056 typ (1.422 typ) .100 BSC (2.54) .310 ±.010 (7.874 ±.254) .180 max (4.572 max) .200 max (5.080 max) .015 min (.381 min) .125 min (3.175 min) .018 ±.003 (.457 ±.760) 0° to 15° BSC = “Basic Spacing between Centers” is theoretical true position dimension and has no tolerance. (JEDEC Standard 95) HOLT INTEGRATED CIRCUITS 9 .010 ±.002 (.254 ±.051)