HYNIX HMT42GR7CMR4C-PB

240pin DDR3 SDRAM Registered DIMM
DDR3 SDRAM Registered DIMM
Based on 2Gb C-die
HMT325R7CFR8C
HMT351R7CFR8C
HMT351R7CFR4C
HMT31GR7CFR8C
HMT31GR7CFR4C
HMT42GR7CMR4C
*SK hynix reserves the right to change products or specifications without notice.
Rev. 1.0 /Jul. 2012
1
Revision History
Revision No.
History
Draft Date
0.1
Initial Release
Aug.2011
0.2
Typo Collected : 1866 Speed bin table update
Sep.2011
1.0
Latest JEDEC Spec and Product Line-up Updated
Jul.2012
Rev. 1.0 / Jul. 2012
Remark
2
Description
Registered DDR3 SDRAM DIMMs (Registered Double Data Rate Synchronous DRAM Dual In-Line Memory
Modules) are low power, high-speed operation memory modules that use DDR3 SDRAM devices. These
Registered SDRAM DIMMs are intended for use as main memory when installed in systems such as servers
and workstations.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Power Supply: VDD=1.5V (1.425V to 1.575V)
VDDQ = 1.5V (1.425V to 1.575V)
VDDSPD=3.0V to 3.6V
Functionality and operations comply with the DDR3 SDRAM datasheet
8 internal banks
Data transfer rates: PC3-14900, PC3-12800, PC3-10600, PC3-8500
Bi-Directional Differential Data Strobe
8 bit pre-fetch
Burst Length (BL) switch on-the-fly BL8 or BC4(Burst Chop)
Supports ECC error correction and detection
On-Die Termination (ODT)
Temperature sensor with integrated SPD
This product is in compliance with the RoHS directive.
Ordering Information
Part Number
Density
Organization
Component Composition
# of
ranks
FDHS
HMT325R7CFR8C-H9/PB/RD
2GB
256Mx72
256Mx8(H5TQG83CFR)*9
1
X
HMT351R7CFR8C-H9/PB/RD
4GB
512Mx72
256Mx8(H5TQ2G83CFR)*18
2
X
HMT351R7CFR4C-H9/PB/RD
4GB
512Mx72
512Mx4(H5TQ2G43CFR)*18
1
X
HMT31GR7CFR8C-G7/H9/PB
8GB
1Gx72
256Mx8(H5TQ2G83CFR)*36
4
O
HMT31GR7CFR4C-H9/PB/RD
8GB
1Gx72
512Mx4(H5TQ2G43CFR)*36
2
O
HMT42GR7CMR4C-G7/H9/PB
16GB
2Gx72
DDP 1Gx4(H5TQ4G43CMR)*36
4
O
* In order to uninstall FDHS, please contact sales administrator
Rev. 1.0 / Jul. 2012
3
Key Parameters
MT/s
Grade
tCK
(ns)
CAS
Latency
(tCK)
tRCD
(ns)
tRP
(ns)
tRAS
(ns)
tRC
(ns)
CL-tRCD-tRP
DDR3-1066
-G7
1.875
7
13.125
13.125
37.5
50.625
7-7-7
DDR3-1333
-H9
1.5
9
13.5
13.5
(13.125)* (13.125)*
36
49.5
(49.125)*
9-9-9
DDR3-1600
-PB
1.25
11
13.75
13.75
(13.125)* (13.125)*
35
48.75
(48.125)*
11-11-11
DDR3-1866
-RD
1.07
13
13.91
13.91
(13.125)* (13.125)*
34
47.91
(48.125)*
13-13-13
*SK hynix DRAM devices support optional downbinning to CL11, CL9 and CL7. SPD setting is programmed to match.
Speed Grade
Frequency [MHz]
Grade
Remark
CL6
CL7
CL8
CL9
CL10
-G7
800
1066
1066
-H9
800
1066
-PB
800
-RD
800
CL11
1066
1333
1333
1066
1066
1333
1333
1600
1066
1066
1333
1333
1600
CL12
CL13
1866
Address Table
2GB(1Rx8)
4GB(2Rx8)
4GB(1Rx4)
8GB(4Rx8)
8GB(2Rx4)
16GB(4Rx4)
Refresh
Method
8K/64ms
8K/64ms
8K/64ms
8K/64ms
8K/64ms
8K/64ms
Row Address
A0-A14
A0-A14
A0-A14
A0-A14
A0-A14
A0-A14
Column
Address
A0-A9
A0-A9
A0-A9,A11
A0-A9
A0-A9,A11
A0-A9,A11
Bank Address
BA0-BA2
BA0-BA2
BA0-BA2
BA0-BA2
BA0-BA2
BA0-BA2
Page Size
1KB
1KB
1KB
1KB
1KB
1KB
Rev. 1.0 / Jul. 2012
4
Pin Descriptions
Pin Name
Description
Num
ber
Pin Name
Description
Num
ber
CK0
Clock Input, positive line
1
ODT[1:0]
On Die Termination Inputs
2
CK0
Clock Input, negative line
1
DQ[63:0]
Data Input/Output
64
CK1
Clock Input, positive line
1
CB[7:0]
CK1
Clock Input, negative line
1
DQS[8:0]
Clock Enables
2
DQS[8:0]
RAS
Row Address Strobe
1
DM[8:0]/
DQS[17:9],
TDQS[17:9]
CAS
Column Address Strobe
1
DQS[17:9],
TDQS[17:9]
WE
Write Enable
1
EVENT
S[3:0]
Chip Selects
4
TEST
Memory bus test tool (Not Connected and Not Usable on DIMMs)
1
Address Inputs
14
RESET
Register and SDRAM control pin
1
A10/AP
Address Input/Autoprecharge
1
VDD
Power Supply
22
A12/BC
Address Input/Burst chop
1
VSS
Ground
59
BA[2:0]
SDRAM Bank Addresses
3
VREFDQ
Reference Voltage for DQ
1
Reference Voltage for CA
1
Termination Voltage
4
SPD Power
1
CKE[1:0]
A[9:0],A11,
A[15:13]
SCL
Serial Presence Detect (SPD)
Clock Input
1
VREFCA
SDA
SPD Data Input/Output
1
VTT
SA[2:0]
SPD Address Inputs
3
VDDSPD
Par_In
Parity bit for the Address and
Control bus
1
Err_Out
Parity error found on the
Address and Control bus
1
Rev. 1.0 / Jul. 2012
Data check bits Input/Output
Data strobes
Data strobes, negative line
Data Masks / Data strobes,
Termination data strobes
Data strobes, negative line,
Termination data strobes
Reserved for optional hardware
temperature sensing
8
9
9
9
9
1
5
Input/Output Functional Descriptions
Symbol
Type
Polarity
CK0
IN
Positive
Line
Positive line of the differential pair of system clock inputs that drives input to the onDIMM Clock Driver.
CK0
IN
Negative
Line
Negative line of the differential pair of system clock inputs that drives the input to the
on-DIMM Clock Driver.
CK1
IN
Positive
Line
Terminated but not used on RDIMMs.
CK1
IN
Negative
Line
Terminated but not used on RDIMMs.
IN
Active
High
CKE[1:0]
Function
CKE HIGH activates, and CKE LOW deactivates internal clock signals, and device input
buffers and output drivers of the SDRAMs. Taking CKE LOW provides PRECHARGE
POWER-DOWN and SELF REFRESH operation (all banks idle), or ACTIVE POWER DOWN
(row ACTIVE in any bank)
Enables the command decoders for the associated rank of SDRAM when low and disables decoders when high. When decoders are disabled, new commands are ignored
and previous operations continue. Other combinations of these input signals perform
unique functions, including disabling all outputs (except CKE and ODT) of the register(s)
on the DIMM or accessing internal control words in the register device(s). For modules
with two registers, S[3:2] operate similarly to S[1:0] for the second set of register outputs or register control words.
S[3:0]
IN
Active
Low
ODT[1:0]
IN
Active
High
On-Die Termination control signals
RAS, CAS, WE
IN
Active
Low
When sampled at the positive rising edge of the clock, CAS, RAS, and WE define the
operation to be executed by the SDRAM.
VREFDQ
Supply
Reference voltage for DQ0-DQ63 and CB0-CB7.
VREFCA
Supply
Reference voltage for A0-A15, BA0-BA2, RAS, CAS, WE, S0, S1, CKE0, CKE1, Par_In,
ODT0 and ODT1.
BA[2:0]
IN
—
Selects which SDRAM bank of eight is activated.
BA0 - BA2 define to which bank an Active, Read, Write or Precharge command is being
applied. Bank address also determines mode register is to be accessed during an MRS
cycle.
A[15:13,
12/BC,11,
10/AP,[9:0]
IN
—
Provided the row address for Active commands and the column address
and Auto Precharge bit for Read/Write commands to select one location out of the memory array in the respective bank. A10 is sampled during a Precharge command to determine whether the Precharge applies to one bank (A10 LOW) or all banks (A10 HIGH). If
only one bank is to be precharged, the bank is selected by BA. A12 is also utilized for BL
4/8 identification for ‘’BL on the fly’’ during CAS command. The address inputs also provide the op-code during Mode Register Set commands.
DQ[63:0],
CB[7:0]
I/O
—
Data and Check Bit Input/Output pins
DM[8:0]
IN
Active
High
VDD, VSS
Supply
Power and ground for the DDR SDRAM input buffers and core logic.
VTT
Supply
Termination Voltage for Address/Command/Control/Clock nets.
Rev. 1.0 / Jul. 2012
Masks write data when high, issued concurrently with input data.
6
Symbol
Type
Polarity
Function
DQS[17:0]
I/O
Positive
Edge
Positive line of the differential data strobe for input and output data.
DQS[17:0]
I/O
Negative
Edge
Negative line of the differential data strobe for input and output data.
TDQS/TDQS is applicable for X8 DRAMs only. When enabled via Mode Register A11=1 in
MR1,DRAM will enable the same termination resistance function on TDQS/TDQS that is
applied to DQS/DQS. When disabled via mode register A11=0 in MR1, DM/TDQS will
provide the data mask function and TDQS is not used. X4/X16 DRAMs must disable the
TDQS function via mode register A11=0 in MR1
TDQS[17:9]
TDQS[17:9]
OUT
SA[2:0]
IN
—
These signals are tied at the system planar to either VSS or VDDSPD to configure the
serial SPD EEPROM address range.
SDA
I/O
—
This bidirectional pin is used to transfer data into or out of the SPD EEPROM. A resistor
must be connected from the SDA bus line to VDDSPD on the system planar to act as a
pullup.
SCL
IN
—
This signal is used to clock data into and out of the SPD EEPROM. A resistor may be connected from the SCL bus time to VDDSPD on the system planar to act as a pullup.
EVENT
OUT
(open
drain)
VDDSPD
Supply
Serial EEPROM positive power supply wired to a separate power pin at the connector
which supports from 3.0 Volt to 3.6 Volt (nominal 3.3V) operation.
RESET
IN
The RESET pin is connected to the RESET pin on the register and to the RESET pin on
the DRAM.
Par_In
IN
Parity bit for the Address and Control bus. (“1 “: Odd, “0 “: Even)
Err_Out
OUT
(open
drain)
TEST
Rev. 1.0 / Jul. 2012
This signal indicates that a thermal event has been detected in the thermal sensing
device.The system should guarantee the electrical level requirement is met for the
Active Low
EVENT pin on TS/SPD part.
No pull-up resister is provided on DIMM.
Parity error detected on the Address and Control bus. A resistor may be connected from
Err_Out bus line to VDD on the system planar to act as a pull up.
Used by memory bus analysis tools (unused (NC) on memory DIMMs)
7
Pin Assignments
Pin #
Front Side
(left 1–60)
Pin #
Back Side
(right 121–180)
Pin #
Front Side
(left 61–120)
Pin #
Back Side
(right 181–240)
1
VREFDQ
121
VSS
61
A2
181
A1
2
VSS
122
DQ4
62
VDD
182
VDD
3
DQ0
123
DQ5
63
NC, CK1
183
VDD
4
DQ1
124
VSS
64
NC, CK1
184
CK0
5
VSS
125
DM0,DQS9,
TDQS9
65
VDD
185
CK0
6
DQS0
126
NC,DQS9,
TDQS9
66
VDD
186
VDD
7
DQS0
127
VSS
67
VREFCA
187
EVENT, NC
8
VSS
128
DQ6
68
Par_In, NC
188
A0
9
DQ2
129
DQ7
69
VDD
189
VDD
10
DQ3
130
VSS
70
A10 / AP
190
BA1
11
VSS
131
DQ12
71
BA0
191
VDD
12
DQ8
132
DQ13
72
VDD
192
RAS
13
DQ9
133
VSS
73
WE
193
S0
14
VSS
134
DM1,DQS10,
TDQS10
74
CAS
194
VDD
15
DQS1
135
NC,DQS10,
TDQS10
75
VDD
195
ODT0
16
DQS1
136
VSS
76
S1, NC
196
A13
17
VSS
137
DQ14
77
ODT1, NC
197
VDD
18
DQ10
138
DQ15
78
VDD
198
S3, NC
19
DQ11
139
VSS
79
S2, NC
199
VSS
20
VSS
140
DQ20
80
VSS
200
DQ36
21
DQ16
141
DQ21
81
DQ32
201
DQ37
22
DQ17
142
VSS
82
DQ33
202
VSS
83
VSS
203
DM4,DQS13,
TDQS13
23
VSS
143
DM2,DQS11,
TDQS11
24
DQS2
144
NC,DQS11,
TDQS11
84
DQS4
204
NC,DQS13,
TDQS13
25
DQS2
145
VSS
85
DQS4
205
VSS
26
VSS
146
DQ22
86
VSS
206
DQ38
27
DQ18
147
DQ23
87
DQ34
207
DQ39
28
DQ19
148
VSS
88
DQ35
208
VSS
29
VSS
149
DQ28
89
VSS
209
DQ44
30
DQ24
150
DQ29
90
DQ40
210
DQ45
31
DQ25
151
VSS
91
DQ41
211
VSS
NC = No Connect; RFU = Reserved Future Use
Rev. 1.0 / Jul. 2012
8
Pin #
Front Side
(left 1–60)
Pin #
Back Side
(right 121–180)
Pin #
Front Side
(left 61–120)
Pin #
Back Side
(right 181–240)
32
VSS
152
DM3,DQS12,
TDQS12
92
VSS
212
DM5,DQS14,
TDQS14
33
DQS3
153
NC,DQS12,
TDQS12
93
DQS5
213
NC,DQS14,
TDQS14
34
DQS3
154
VSS
94
DQS5
214
VSS
35
VSS
155
DQ30
95
VSS
215
DQ46
36
DQ26
156
DQ31
96
DQ42
216
DQ47
37
DQ27
157
VSS
97
DQ43
217
VSS
38
VSS
158
CB4, NC
98
VSS
218
DQ52
39
CB0, NC
159
CB5, NC
99
DQ48
219
DQ53
40
CB1, NC
160
VSS
100
DQ49
220
VSS
41
VSS
161
NC,DM8,DQS17,
TDQS17
101
VSS
221
DM6,DQS15,
TDQS15
42
DQS8
162
NC,DQS17,
TDQS17
102
DQS6
222
NC,DQS15,
TDQS15
43
DQS8
163
VSS
103
DQS6
223
VSS
44
VSS
164
CB6, NC
104
VSS
224
DQ54
45
CB2, NC
165
CB7, NC
105
DQ50
225
DQ55
46
CB3, NC
166
VSS
106
DQ51
226
VSS
47
VSS
167
NC(TEST)
107
VSS
227
DQ60
VTT, NC
168
RESET
108
DQ56
228
DQ61
109
DQ57
229
VSS
48
KEY
KEY
49
VTT, NC
169
CKE1, NC
110
VSS
230
DM7,DQS16,
TDQS16
50
CKE0
170
VDD
111
DQS7
231
NC,DQS16,
TDQS16
51
VDD
171
A15
112
DQS7
232
VSS
52
BA2
172
A14
113
VSS
233
DQ62
53
Err_Out, NC
173
VDD
114
DQ58
234
DQ63
54
VDD
174
A12 / BC
115
DQ59
235
VSS
55
A11
175
A9
116
VSS
236
VDDSPD
56
A7
176
VDD
117
SA0
237
SA1
57
VDD
177
A8
118
SCL
238
SDA
58
A5
178
A6
119
SA2
239
VSS
59
A4
179
VDD
120
VTT
240
VTT
60
VDD
180
A3
NC = No Connect; RFU = Reserved Future Use
Rev. 1.0 / Jul. 2012
9
Registering Clock Driver Specifications
Capacitance Values
Symbol
CI
CIR
Parameter
Conditions
Min
Typ
Max
Unit
Input capacitance, Data inputs
1.5
-
2.5
pF
Input capacitance, CK, CK, FBIN, FBIN
(up to DDR3-1600)
1.5
-
2.5
pF
-
-
3
pF
Input capacitance, RESET, MIRROR,
QCSEN
VI = VDD or GND; VDD = 1.5v
Input & Output Timing Requirements
Symbol
Parameter
Conditions
DDR3-800
1066/1333
DDR3-1600
DDR3-1866
Unit
Min
Max
Min
Max
Min
Max
fclock
Input clock frequency
Application frequency
300
670
300
810
300
945
Mhz
fTEST
Input clock frequency
Test frequency
70
300
70
300
70
300
Mhz
tSU
Setup time
Input valid before
CK/CK
100
-
50
-
40
-
ps
tH
Hold time
Input to remain
valid after CK/CK
175
-
125
-
75
-
ps
tPDM
Propagation
delay, single-bit CK/CK to output
switching
0.65
1.0
0.65
1.0
0.65
1.0
ns
tDIS
Output disable
Yn/Yn to output
0.5 +
time (1/2-Clock
tQSK1(min)
float
prelaunch)
-
0.5 +
tQSK1(min)
-
0.5 +
tQSK1(min)
-
ps
tEN
Output enable
Output driving to
0.5 time (1/2-Clock
tQSK1(max)
Yn/Yn
prelaunch)
-
0.5 tQSK1(max)
-
0.5 tQSK1(max)
-
ps
Rev. 1.0 / Jul. 2012
10
On DIMM Thermal Sensor
The DDR3 SDRAM DIMM temperature is monitored by integrated thermal sensor. The integrated thermal
sensor comply with JEDEC “TSE2002av, Serial Presence Detect with Temperature Sensor”.
Connection of Thermal Sensor
EVENT
SCL
SDA
SA0
SPD with SA1
Integrated SA2
TS
EVENT
SCL
SA0
SDA
SA1
SA2
Temperature-to-Digital Conversion Performance
Parameter
Temperature Sensor Accuracy (Grade B)
Resolution
Rev. 1.0 / Jul. 2012
Condition
Min
Typ
Max
Unit
Active Range,
75°C < TA < 95°C
-
± 0.5
± 1.0
°C
Monitor Range,
40°C < TA < 125°C
-
± 1.0
± 2.0
°C
-20°C < TA < 125°C
-
± 2.0
± 3.0
°C
0.25
°C
11
RODT0B
PCK0B
RCKE0B
RWEB
PCK0B
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
CAS
WE
ODT
CK
CKE
CK
WE
CAS
D5
ODT
CK
CKE
CK
WE
CAS
D6
A[O:N]/BA[N:O]
ZQ
ODT
CK
CKE
CK
D7
A[N:O]/BA[N:O]
ZQ
WE
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
ZQ
A[O:N]/BA[N:O]
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
D0
RCASB
DQS7
DQS7
DM7/DQS16
DQS16
DQ[63:56]
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
CS
DQS6
DQS6
DM6/DQS15
DQS15
DQ[55:48]
D4
CAS
ODT
A[O:N]/BA[N:O]
A[N:O]/BA[N:O]
ODT
DQS
DQS
TDQS
TDQS
DQ [7:0]
RAS
ODT
ODT
CK
CKE
CK
CKE
CK
CKE
RS0B
RRASB
A[N:O]A
/BA[N:O]A
RODT0A
PCK0A
RCKE0A
CK
CKE
CK
CK
D1
WE
CAS
RAS
CK
WE
ZQ
DQS
DQS
TDQS
TDQS
DQ [7:0]
CS
CK
CAS
WE
WE
CAS
CAS
CAS
D2
WE
RAS
CS
CS
RAS
RAS
ZQ
DQS5
DQS5
DM5/DQS14
DQS14
DQ[47:40]
CS
DQS
DQS
TDQS
TDQS
DQ [7:0]
D3
DQS
DQS
TDQS
TDQS
DQ [7:0]
RAS
DQS1
DQS1
DM1/DQS10
DQS10
DQ[15:8]
ZQ
ZQ
DQS4
DQS4
DM4/DQS13
DQS13
DQ[39:32]
CS
DQS
DQS
TDQS
TDQS
DQ [7:0]
A[N:O]/BA[N:O]
DQS2
DQS2
DM2/DQS11
DQS11
DQ[23:16]
D8
A[O:N]/BA[N:O]
DQS
DQS
TDQS
TDQS
DQ [7:0]
RAS
DQS3
DQS3
DM3/DQS12
DQS12
DQ[31:24]
CS
DQS
DQS
TDQS
TDQS
DQ [7:0]
CS
RWEA
ZQ
DQS8
DQS8
DM8/DQS17
DQS17
CB[7:0]
DQS0
DQS0
DM0/DQS9
DQS9
DQ[7:0]
PCK0A
RS0A
RRASA
RCASA
2GB, 256Mx72 Module(1Rank of x8)
A[N:O]B
/BA[N:O]B
Functional Block Diagram
Vtt
VDDSPD
SPD
VDD
D0–D8
VTT
VREFCA
D0–D8
VREFDQ
D0–D8
VSS
D0–D8
Note:
1.DQ-to-I/O wiring may be changed within byte.
2.ZQ resistors are 240 Ω ±1%.For all other resistor values refer to the
appropriate wiring diagram.
Vtt
S0
S1
BA[N:0]
A[N:0]
RAS
CAS
WE
CKE0
ODT0
CK0
CK0
CK0
CK0
PAR_IN
120 Ω
±1%
1:
2
R
E
G
I
S
T
E
R
/
P
L
L
120 Ω
±1%
RESET
OERR
RST
RS0A → CS0: SDRAMs D[3:0], D8
RS0B → CS0: SDRAMs D[7:4]
RBA[N:0]A → BA[N:0]: SDRAMs D[3:0], D8
RBA[N:0]A → BA[N:0]: SDRAMs D[7:4]
RA[N:0]A → A[N:0]: SDRAMs D[3:0], D8
RA[N:0]A → A[N:0]: SDRAMs D[7:4]
RRASA → RAS: SDRAMs D[3:0], D8
RRASA → RAS: SDRAMs D[7:4]
RCASA → CAS: SDRAMs D[3:0], D8
RCASA → CAS: SDRAMs D[7:4]
RWEA → WE: SDRAMs D[3:0], D8
RWEA → WE: SDRAMs D[7:4]
RCKE0A → CKE0: SDRAMs D[3:0], D8
RCKE0B → CKE0: SDRAMs D[7:4]
RODT0A → ODT0: SDRAMs D[3:0], D8
RODT0B → ODT0: SDRAMs D[7:4]
PCK0A → CK: SDRAMs D[3:0], D8
PCK0B → CK: SDRAMs D[7:4]
PCK0A → CK: SDRAMs D[3:0], D8
PCK0B → CK: SDRAMs D[7:4]
VDDSPD
EVENT
SCL
SDA
VDDSPD
SA0
SA0
EVENT SPD with SA1
Integrated SA2
SCL
TS
VSS
SDA
SA1
SA2
VSS
Plan to use SPD with Integrated TS of Class B and
might be changed on customer’s requests. For more
details of SPD and Thermal sensor, please contact
local SK hynix sales representative
Err_Out
RST: SDRAMs D[8:0]
S[3:2], CKE1, ODT1, are NC (Unused register inputs ODT1 and CKE1 have a 330 Ω resistor to ground
Rev. 1.0 / Jul. 2012
12
RODT1B
A[N:O]/BA[N:O]
ODT
A[N:O]/BA[N:O]
A[O:N]/BA[N:O]
ODT
ODT
ODT
CK
CKE
CK
CKE
A[N:O]/BA[N:O]
PCK1B
CK
WE
CK
CKE
CK
CKE
CK
WE
WE
D16
CAS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
CK
WE
D15
CAS
CS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
CK
RAS
CS
CAS
D14
CAS
CS
RAS
A[N:O]/BA[N:O]
ZQ
PCK1B
RCKE1B
RS1B
A[N:O]B
/BA[N:O]B
A[N:O]/BA[N:O]
D13
DQS
DQS
TDQS
TDQS
DQ [7:0]
CS
ODT
CK
CKE
ZQ
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CKE
ODT
ODT
CK
CKE
CK
DQS
DQS
TDQS
TDQS
DQ [7:0]
A[N:O]/BA[N:O]
PCK0B
RCKE0B
RODT0B
PCK0B
RCASB
RWEB
WE
CK
CK
WE
WE
ZQ
D7
A[N:O]/BA[N:O]
ODT
CK
CKE
VDDSPD
EVENT
Vtt
SCL
SDA
Note:
1. DQ-to-I/O wiring may be changed within a byte.
2. Unless otherwise noted, resistor values are 15 Ω ±5%.
3. ZQ resistors are 240 Ω ±1%. For all other resistor values
refer to the appropriate wiring diagram.
4. See the wiring diagrams for all resistors associated with the
command, address and control bus.
Rev. 1.0 / Jul. 2012
WE
DQS
DQS
TDQS
TDQS
DQ [7:0]
CK
RS0B
RRASB
DQS7
DQS7
DM7/DQS16
DQS16
DQ[63:56]
D6
CAS
CS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
CAS
DQS6
DQS6
DM6/DQS15
DQS15
DQ55:48]
D5
CAS
CS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
RAS
DQS5
DQS5
DM5/DQS14
DQS14
DQ[47:40]
D4
CAS
CS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
CS
PCK1A
RODT1A
ODT
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
ODT
ODT
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CKE
A[O:N]/BA[N:O]
CK
CKE
CK
CKE
CK
CAS
WE
WE
D9
CAS
RAS
DQS4
DQS4
DM4/DQS13
DQS13
DQ[39:32]
Vtt
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
CAS
WE
WE
D10
CAS
CS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
CK
RAS
CS
D11
CK
RAS
CS
D12
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
WE
CAS
D17
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
PCK1A
RCKE1A
RS1A
CS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
CS
RODT0A
A[N:O]A
/BA[N:O]A
A[N:O]/BA[N:O]
ODT
ODT
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
ODT
ODT
ODT
A[O:N]/BA[N:O]
CK
CKE
CK
CKE
CK
CKE
CK
CKE
A[N:O]/BA[N:O]
RWEA
PCK0A
RCASA
PCK0A
RCKE0A
CK
CKE
CK
WE
CK
D0
WE
CS
CK
WE
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
D1
WE
CS
ZQ
DQS0
DQS0
DM0/DQS9
DQS9
DQ[7:0]
WE
DQS
DQS
TDQS
TDQS
DQ [7:0]
CAS
DQS1
DQS1
DM1/DQS10
DQS10
DQ[15:8]
D2
CAS
CS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
RAS
DQS2
DQS2
DM2/DQS11
DQS11
DQ[23:16]
D3
CAS
CS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
CAS
DQS3
DQS3
DM3/DQS12
DQS12
DQ[31:24]
D8
CAS
CS
ZQ
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
RAS
DQS8
DQS8
DM8/DQS17
DQS17
CB[7:0]
CK
RS0A
RRASA
4GB, 512Mx72 Module(2Rank of x8) - page1
VDDSPD
SA0
SA0
EVENT SPD with SA1
Integrated SA2
SCL
TS
VSS
SDA
SA1
SA2
VSS
Plan to use SPD with Integrated TS of Class B and
might be changed on customer’s requests. For more
details of SPD and Thermal sensor, please contact
local SK hynix sales representative
VDDSPD
Serial PD
VDD
D0–D17
VTT
VREFCA
D0–D17
VREFDQ
D0–D17
VSS
D0–D17
D0–D17
13
4GB, 512Mx72 Module(2Rank of x8) - page2
S0
1:2
S1
S[3:2] NC
BA[N:0]
R
E
G
I
S
T
E
R
/
P
L
L
A[N:0]
RAS
CAS
WE
CKE0
CKE1
ODT0
ODT1
CK0
120 Ω
±5%
CK0
CK1
CK1
120 Ω
±5%
PAR_IN
RS0A → CS0: SDRAMs D[3:0], D8
RS0B → CS0: SDRAMs D[7:4]
RS1A → CS1: SDRAMs D[12:9], D17
RS1B → CS1: SDRAMs D[16:13]
RBA[N:0]A → BA[N:0]: SDRAMs D[3:0], D[12:8], D17
RBA[N:0]B → BA[N:0]: SDRAMs D[7:4], D[16:13]
RA[N:0]A → A[N:0]: SDRAMs D[3:0], D[12:8], D17
RA[N:0]B → A[N:0]: SDRAMs D[7:4], D[16:13]
RRASA → RAS: SDRAMs D[3:0], D[12:8], D17
RRASB → RAS: SDRAMs D[7:4], D[16:13]
RCASA → CAS: SDRAMs D[3:0], D[12:8], D17
RCASB → CAS: SDRAMs D[7:4], D[16:13]
RWEA → WE: SDRAMs D[3:0], D[12:8], D17
RWEB → WE: SDRAMs D[7:4], D[16:13]
RCKE0A → CKE0: SDRAMs D[3:0], D8
RCKE0B → CKE0: SDRAMs D[7:4]
RCKE1A → CKE1: SDRAMs D[12:9], D17
RCKE1B → CKE1: SDRAMs D[16:13]
RODT0A → ODT0: SDRAMs D[3:0], D8
RODT0B → ODT0: SDRAMs D[7:4]
RODT1A → ODT1: SDRAMs D[12:9], D17
RODT1A → ODT1: SDRAMs D[16:13]
PCK0A → CK: SDRAMs D[3:0], D8
PCK0B → CK: SDRAMs D[7:4]
PCK1A → CK: SDRAMs D[12:9], D17
PCK1B → CK: SDRAMs D[16:13]
PCK0A → CK: SDRAMs D[3:0], D8
PCK0B → CK: SDRAMs D[7:4]
PCK1A → CK: SDRAMs D[12:9], D17
PCK1B → CK: SDRAMs D[16:13]
OERR Err_Out
RESET
RST
RST: SDRAMs D[17:0]
* S[3:2], CK1 and CK1 are NC
Rev. 1.0 / Jul. 2012
14
ODT
CK
CKE
CK
VSS
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
WE
CAS
VSS
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
VSS
A[O:N]/BA[O:N]
ODT
CK
CK
CKE
D15
ODT
CK
CKE
VSS
D16
A[O:N]/BA[O:N]
ZQ
CK
RAS
CS
CAS
ZQ
CAS
RAS
CS
D14
CAS
ODT
A[O:N]/BA[O:N]
A[O:N]/BA[O:N]
ODT
CK
CKE
D7
RAS
DQS
DQS
DM
DQ [3:0]
ZQ
WE
DQS16
DQS16
VSS
DQ[63:60]
ZQ
RAS
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
CKE
D6
D13
WE
DQS
DQS
DM
DQ [3:0]
ZQ
ZQ
WE
DQS15
DQS15
VSS
DQ[55;52]
CS
VSS
VSS
A[O:N]/BA[O:N]
DQS
DQS
DM
DQ [3:0]
VSS
ODT
VSS
DQS14
DQS14
VSS
DQ[47:44]
CS
RODT0B
A[O:N]B
/BA[O:N]B
RWEB
PCK0B
RCASB
PCK0B
RCKE0B
CK
CKE
CK
WE
CK
WE
CAS
CAS
CAS
CAS
RAS
CS
DQS
DQS
DM
DQ [3:0]
Vtt
VSS
D9
A[O:N]/BA[O:N]
ZQ
RAS
CS
CS
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
WE
CAS
D10
D5
CK
DQS
DQS
DM
DQ [3:0]
DQS13
DQS13
VSS
DQ[39:36]
ZQ
WE
DQS7
DQS7
VSS
DQ[59:56]
ZQ
RAS
A[O:N]/BA[O:N]
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
WE
CAS
D11
D4
CK
DQS
DQS
DM
DQ [3:0]
ZQ
WE
RS0B
RRASB
DQS6
DQS6
VSS
DQ[51:48]
ZQ
RAS
DQS
DQS
DM
DQ [3:0]
CS
VSS
A[O:N]/BA[O:N]
VSS
DQS5
DQS5
VSS
DQ[43:40]
VSS
ODT
DQS
DQS
DM
DQ [3:0]
VSS
ODT
CK
CKE
CK
WE
CAS
D12
WE
CS
RAS
RAS
CS
DQS4
DQS4
VSS
DQ[35:32]
ZQ
CAS
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
WE
D0
CK
CKE
DQS
DQS
DM
DQ [3:0]
ZQ
D17
CK
DQS9
DQS9
VSS
DQ[7:4]
CS
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
WE
CAS
D1
ZQ
WE
DQS
DQS
DM
DQ [3:0]
CAS
DQS10
DQS10
VSS
DQ[15:12]
ZQ
RAS
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
WE
CAS
D2
RAS
DQS
DQS
DM
DQ [3:0]
CS
DQS11
DQS11
VSS
DQ23:20]
ZQ
RAS
A[O:N]/BA[O:N]
ODT
CK
CKE
CK
WE
CAS
D3
CS
PCK0A
RCKE0A
RODT0A
RWEA
PCK0A
A[O:N]A
/BA[O:N]A
VSS
CAS
DQS
DQS
DM
DQ [3:0]
ZQ
CAS
CS
RAS
RAS
CS
CS
RAS
RAS
CS
A[O:N]/BA[O:N]
DQS
DQS
DM
DQ [3:0]
VSS
DQS0
DQS0
VSS
DQ[3:0]
DQS12
DQS12
VSS
DQ[31:28]
VSS
DQS
DQS
DM
DQ [3:0]
DQS
DQS
DM
DQ [3:0]
VSS
DQS1
DQS1
VSS
DQ[11;8]
DQS17
DQS17
VSS
CB[7:4]
VSS
DQS
DQS
DM
DQ [3:0]
ODT
DQS2
DQS2
VSS
DQ[19:16]
D8
CK
CKE
DQS
DQS
DM
DQ [3:0]
ZQ
CK
DQS3
DQS3
VSS
DQ[27:24]
RAS
DQS
DQS
DM
DQ [3:0]
CS
DQS8
DQS8
VSS
CB[3:0]
WE
RS0A
RRASA
RCASA
4GB, 512Mx72 Module(1Rank of x4) - page1
Vtt
VDDSPD
EVENT
SCL
SDA
SA0
SA0
EVENT SPD with SA1
Integrated SA2
SCL
TS
VSS
SDA
VDDSPD
SA1
SA2
VSS
Plan to use SPD with Integrated TS of Class B and
might be changed on customer’s requests. For more
details of SPD and Thermal sensor, please contact
local SK hynix sales representative
Note:
1. DQ-to-I/O wiring may be changed within a nibble.
2. Unless otherwise noted, resistor values are 15%.
 5
3. See the wiring diagrams for all resistors associated with the command, address and control bus.
 For
 1 all other resistor values refer to the appro4. ZQ resistors are 240%.
priate wiring diagram.
Rev. 1.0 / Jul. 2012
VDDSPD
SPD
VDD
D0–D17
VTT
VREFCA
D0–D17
VREFDQ
D0–D17
VSS
D0–D17
D0–D17
15
4GB, 512Mx72 Module(1Rank of x4) - page2
S0
S1
1:2
BA[N:0]
R
E
A[N:0]
G
RAS
I
S
T
E
R
/
P
L
L
CAS
WE
CKE0
ODT0
RS0A → CS0: SDRAMs D[3:0], D[12:8], D17
RS0B → CS0: SDRAMs D[7:4], D[16:13]
RS1A → CS1: SDRAMs D[12:9], D17
RS1B → CS1: SDRAMs D[16:13]
RBA[N:0]A → BA[N:0]: SDRAMs D[3:0], D[12:8], D17
RBA[N:0]B → BA[N:0]: SDRAMs D[7:4], D[16:13]
RA[N:0]A → A[N:0]: SDRAMs D[3:0], D[12:8], D17
RA[N:0]B → A[N:0]: SDRAMs D[7:4], D[16:13]
RRASA → RAS: SDRAMs D[3:0], D[12:8], D17
RRASB → RAS: SDRAMs D[7:4], D[16:13]
RCASA → CAS: SDRAMs D[3:0], D[12:8], D17
RCASB → CAS: SDRAMs D[7:4], D[16:13]
RWEA → WE: SDRAMs D[3:0], D[12:8], D17
RWEB → WE: SDRAMs D[7:4], D[16:13]
RCKE0A → CKE0: SDRAMs D[3:0], D[12:8], D17
RCKE0B → CKE0: SDRAMs D[7:4], D[16:13]
RODT0A → ODT0: SDRAMs D[3:0], D[12:8]. D17
RODT0B → ODT0: SDRAMs D[7:4], D[16:13]
CK0
PCK0A → CK: SDRAMs D[3:0], D8
PCK0B → CK: SDRAMs D[7:4]
CK0
PCK0A → CK: SDRAMs D[3:0], D8
PCK0B → CK: SDRAMs D[7:4]
PAR_IN
OERR Err_Out
RESET
RST
RST: SDRAMs D[17:0]
* S[3:2], CKE1, ODT1, CK1 and CK1 are NC (Unused register inputs ODT1 and CKE1 have a 330 resistor to ground.)
Rev. 1.0 / Jul. 2012
16
CS
CS
CS
CS
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
DQS8
DQS8
DM8/TDQS17
TDQS17
CB[7:0]
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
Rev. 1.0 / Jul. 2012
U6
CKE
U15
U24
A[N:O]
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
ODT
BA[N:O]
BA[N:O]
CKE
A[N:O]
U32
ODT
CKE
CKE
CK
CK
BA[N:O]
A[N:O]
ODT
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
CK
WE
CAS
CS
CKE
CK
CK
WE
CAS
RAS
BA[N:O]
A[N:O]
ODT
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
CK
WE
CAS
CS
RAS
BA[N:O]
A[N:O]
ODT
CKE
CK
CK
WE
CAS
PCK0
CK
BA[N:O]
A[N:O]
ODT
CKE
CK
CK
WE
CAS
RAS
CS
BA[N:O]
A[N:O]
VDD
WCKE1
PCK2
PCK2
CS3
WCKE0
WODT1
CKE
CK
ODT
PCK2
PCK2
CK
WE
CAS
RAS
CS
BA[N:O]
CS2
WCKE01
VDD
CKE
A[N:O]
ODT
PCK0
PCK0
CK
CS1
CK
WE
CAS
RAS
CS
WA[N:0]
WBA[N:0]
A[N:O]
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
A[N:O]
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
WE
CAS
U23
CS
U22
RAS
A[N:O]
BA[N:O]
U21
RAS
A[N:O]
BA[N:O]
ODT
CKE
CK
CK
WE
CAS
CS
RAS
U20
CS
BA[N:O]
CKE
ODT
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CKE
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
CK
WE
CAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
CK
CS
RAS
BA[N:O]
A[N:O]
ODT
CKE
CK
CK
WE
CAS
WWE
PCK0
CK
WCAS
WE
WRAS
CS0
CAS
CS
RAS
BA[N:O]
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
ODT
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
WE
CAS
U14
CS
U13
RAS
BA[N:O]
U12
RAS
BA[N:O]
A[N:O]
ODT
CKE
CK
CK
WE
CAS
CS
RAS
U11
CS
BA[N:O]
CKE
A[N:O]
ODT
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
A[N:O]
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
CK
WE
CAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
CK
CS
RAS
BA[N:O]
A[N:O]
ODT
CKE
CK
CK
WE
CAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
ODT
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
WE
CAS
U5
CS
U4
RAS
BA[N:O]
A[N:O]
ODT
CKE
CK
CK
WE
CAS
U3
RAS
BA[N:O]
A[N:O]
ODT
CKE
CK
CK
WE
CAS
U2
CS
BA[N:O]
A[N:O]
ODT
CKE
CK
CK
WE
CAS
WCKE0
DQS3
DQS3
DM3/TDQS12
TDQS12
DQ[31:24]
WODT0
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CKE
DQS2
DQS2
DM2/TDQS11
TDQS11
DQ[32:16]
ODT
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
RAS
DQS1
DQS1
DM1/TDQS10
TDQS10
DQ[15:8]
RAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
RAS
DQS0
DQS0
DM0/TDQS9
TDQS9
DQ[7:0]
RAS
8GB, 1Gx72 Module(4Rank of x8) - page1
U29
U30
U31
U33
Vtt
17
BA[N:O]
VDD
ODT
A[N:O]
WCKE1
PCK2
CK
CK
WE
CKE
PCK2
BA[N:O]
ODT
A[N:O]
CKE
CK
CK
ODT
A[N:O]
BA[N:O]
ODT
BA[N:O]
CKE
CK
A[N:O]
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CKE
CK
U36
WE
CAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
CAS
WE
WE
CAS
U35
CK
CAS
CS3
CS
RAS
RAS
CS
CS
RAS
BA[N:O]
A[N:O]
A[N:O]
BA[N:O]
CKE
ODT
U34
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CS
A[N:O]
BA[N:O]
ODT
CKE
CKE
ODT
CK
U28
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
RAS
A[N:O]
BA[N:O]
WCKE0
WODT1
CKE
ODT
PCK2
PCK2
CK
WE
CK
CK
U27
WE
CAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CK
WE
CAS
CK
CK
WE
CAS
U26
CK
CAS
CS2
CS
RAS
RAS
CS
CS
RAS
BA[N:O]
BA[N:O]
U25
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CS
BA[N:O]
ODT
A[N:O]
CKE
CKE
A[N:O]
ODT
ODT
A[N:O]
CKE
U19
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
RAS
BA[N:O]
WCKE01
VDD
CKE
ODT
CK
CK
CK
CK
U18
WE
CAS
CK
WE
CAS
CK
CK
WE
CAS
U17
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
A[N:O]
PCK0
PCK0
CK
WE
CAS
CS1
CS
RAS
RAS
CS
CS
RAS
BA[N:O]
A[N:O]
A[N:O]
BA[N:O]
U16
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CS
A[N:O]
BA[N:O]
CK
ODT
CKE
CKE
ODT
CK
CK
CKE
U10
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
RAS
WA[N:0]
WBA[N:0]
A[N:O]
BA[N:O]
PCK0
WCKE0
WODT0
CK
CKE
ODT
WWE
PCK0
CK
CK
U9
ODT
CAS
RAS
CS
CS
CAS
RAS
CK
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
U8
CK
WCAS
DQS3
DQS3
DM3/TDQS12
TDQS12
DQ[31:24]
WE
WRAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
WE
DQS6
DQS6
DM6/TDQS15
TDQS15
DQ[55:48]
U7
WE
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
CS
DQS5
DQS5
DM5/TDQS14
TDQS14
DQ[47:40]
CAS
DQS
DQS
TDQS
TDQS
DQ [7:0]
ZQ
RAS
DQS4
DQS4
DM4/TDQS13
TDQS13
DQ[39:32]
WE
CS0
CAS
CS
RAS
8GB, 1Gx72 Module(4Rank of x8) - page2
U37
Vtt
VDDSPD
EVENT
SCL
SDA
VDDSPD
SA0
SA0
EVENT SPD with SA1
Integrated SA2
SCL
TS
SDA
VSS
SA1
SA2
Plan to use SPD with Integrated TS of Class B and
might be changed on customer’s requests. For more
details of SPD and Thermal sensor, please contact
local SK hynix sales representative
VSS
VDDSPD
Notes:
1. DQ-to-I/O wiring may be changed within a byte.
2. See wiring diagrams for resistor values.
3. ZQ pins of each SDRAM are connected to individual RZQ resistors (240+/-1%) ohms.
Rev. 1.0 / Jul. 2012
VDD
Serial PD
U1–U37
VTT
VREFCA
U1-U37
VREFDQ
U1-U37
VSS
U1-U37
18
8GB, 1Gx72 Module(4Rank of x8) - page3
S0
S1
S2
S3
BA[N:0]
1:2
R
E
G
I
S
T
E
R
/
P
L
L
A[N:0]
RAS
CAS
WE
CKE0
CKE1
ODT0
ODT1
CK0
CK0
CK1
CK1
120 Ω
±5%
PAR_IN
CS0 → CS0: SDRAMs U[10:2]
CS1 → CS1: SDRAMs U[19:11]
CS2 → CS2: SDRAMs U[28:20]
CS3 → CS3: SDRAMs U[37:29]
WBA[N:0] → BA[N:0]: SDRAMs U[6:2], U[15:11], U[24:20], U[33:29]
EBA[N:0] → BA[N:0]: SDRAMs U[10:7], U[19:16], U[28:25], U[37:34]
WA[N:0] → A[N:0]: SDRAMs U[6:2], U[15:11], U[24:20], U[33:29]
EA[N:0] → A[N:0]: SDRAMs U[10:7], U[19:16], U[28:25], U[37:34]
WRAS → RAS: SDRAMs U[6:2], U[15:11], U[24:20], U[33:29]
ERAS → RAS: SDRAMs U[10:7], U[19:16], U[28:25], U[37:34]
WCAS → CAS: SDRAMs U[6:2], U[15:11], U[24:20], U[33:29]
ECAS → CAS: SDRAMs U[10:7], U[19:16], U[28:25], U[37:34]
WWE → WE: SDRAMs U[6:2], U[15:11], U[24:20], U[33:29]
EWE → WE: SDRAMs U[10:7], U[19:16], U[28:25], U[37:34]
WCKE0 → CKE0: SDRAMs U[6:2], U[24:20]
ECKE0 → CKE0: SDRAMs U[10:7], U[28:25]
WCKE1 → CKE1: SDRAMs U[15:11], U[33:29]
ECKE1 → CKE1: SDRAMs U[19:16], U[37:34]
WODT0 → ODT0: SDRAMs U[6:2]
EODT0 → ODT0: SDRAMs U[10:7]
WODT0 → ODT1: SDRAMs U[24:20]
EODT0 → ODT1: SDRAMs U[28:25]
PCK0 → CK: SDRAMs U[6:2], U[15:11]
PCK1 → CK: SDRAMs U[10:7], U[28:25]
PCK2 → CK: SDRAMs U[24:20], U[33:29]
PCK3 → CK: SDRAMs U[19:16], U[37:34]
PCK0 → CK: SDRAMs U[6:2], U[15:11]
PCK1 → CK: SDRAMs U[10:7], U[28:25]
PCK2 → CK: SDRAMs U[24:20], U[33:29]
PCK3 → CK: SDRAMs U[19:16], U[37:34]
Err_Out
RESET
RST
RST: SDRAMs U[37:2]
Rev. 1.0 / Jul. 2012
19
DQS0
DQS0
VSS
DQ[3:0]
DQS
DQS
DM
DQ [3:0]
Vtt
Rev. 1.0 / Jul. 2012
D0
D18
DQS9
DQS9
VSS
DQ[7:4]
DQS
DQS
DM
DQ [3:0]
D9
DQS
DQS
DM
DQ [3:0]
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
D27
ODT
D19
ODT
CK
CKE
DQS
DQS
DM
DQ [3:0]
CK
CKE
D21
D20
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
D26
A[N:O]/BA[N:O]
ODT
CK
CKE
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
D1
CS
D2
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
D3
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
D8
A[N:O]/BA[N:O]
ODT
DQS
DQS
DM
DQ [3:0]
CK
CKE
DQS1
DQS1
VSS
DQ[11:8]
CK
DQS
DQS
DM
DQ [3:0]
RAS
DQS2
DQS2
VSS
DQ[19:16]
RAS
DQS
DQS
DM
DQ [3:0]
CS
DQS3
DQS3
VSS
DQ[27:24]
RAS
CS
A[N:O]/BA[N:O]
ODT
DQS
DQS
DM
DQ [3:0]
CS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
DQS8
DQS8
VSS
CB[3:0]
WE
CAS
RAS
D28
CS
D29
A[N:O]/BA[N:O]
ODT
CK
CKE
D30
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
D35
A[N:O]/BA[N:O]
ODT
DQS
DQS
DM
DQ [3:0]
CK
CKE
DQS
DQS
DM
DQ [3:0]
CK
CKE
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
D10
A[N:O]/BA[N:O]
D11
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
D12
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
DQS
DQS
DM
DQ [3:0]
D17
CS
CS
DQS10
DQS10
VSS
DQ[15:12]
RAS
DQS
DQS
DM
DQ [3:0]
ODT
CS
DQS11
DQS11
VSS
DQ[23:20]
RAS
DQS
DQS
DM
DQ [3:0]
CK
CKE
CS
DQS12
DQS12
VSS
DQ[31:28]
RAS
DQS
DQS
DM
DQ [3:0]
CK
CS
DQS17
DQS17
VSS
CB[7:4]
WE
CAS
RAS
CS
R0DT1A
RCKE1A
PCK1A
PCK1A
RS1A
A[O:N]A
/BA[O:N]A
RODT0A
PCK0A
RCKE0A
PCK0A
RWEA
RCASA
RS0A
RRASA
R0DT1A
RCKE1A
PCK1A
PCK1A
RS1A
A[O:N]A
/BA[O:N]A
RODT0A
PCK0A
RCKE0A
PCK0A
RWEA
RCASA
RS0A
RRASA
8GB, 1Gx72 Module(2Rank of x4) - page1
Vtt
20
R0DT1B
A[N:O]/BA[N:O]
ODT
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
ODT
ODT
ODT
CK
CKE
CK
CKE
CK
CKE
A[N:O]/BA[N:O]
RCKE1B
PCK1B
PCK1B
CK
CKE
CK
WE
D24
WE
CAS
DQS
DQS
DM
DQ [3:0]
CK
D33
WE
CAS
RAS
CS
DQS
DQS
DM
DQ [3:0]
CK
WE
D23
CK
CAS
RAS
CS
DQS
DQS
DM
DQ [3:0]
RAS
A[N:O]B
/BA[N:O]B
RS1B
D31
CAS
RAS
CS
DQS
DQS
DM
DQ [3:0]
CS
ODT
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CKE
ODT
ODT
CK
CKE
D6
A[N:O]/BA[N:O]
PCK0B
RCKE0B
RWEB
RODT0B
CK
CKE
CK
CK
CAS
CAS
CAS
CAS
RAS
CS
CS
RAS
RAS
CS
CK
DQS
DQS
DM
DQ [3:0]
D15
CK
DQS6
DQS6
VSS
DQ[51:48]
PCK0B
RCASB
DQS
DQS
DM
DQ [3:0]
WE
DQS15
DQS15
VSS
DQ[55:52]
D5
WE
DQS
DQS
DM
DQ [3:0]
D13
WE
DQS5
DQS5
VSS
DQ[43:40]
RAS
DQS
DQS
DM
DQ [3:0]
CS
DQS13
DQS13
VSS
DQ[39:36]
WE
RS0B
RRASB
R0DT1B
A[N:O]/BA[N:O]
ODT
ODT
A[N:O]/BA[N:O]
PCK1B
Vtt
A[N:O]/BA[N:O]
ODT
ODT
CK
CKE
CK
CKE
WE
CAS
D25
A[N:O]/BA[N:O]
CK
WE
CAS
CK
CKE
CK
CKE
CK
WE
CAS
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
D34
CK
RAS
RCKE1B
PCK1B
RS1B
CS
RAS
RAS
CS
D22
DQS
DQS
DM
DQ [3:0]
CS
A[N:O]B
/BA[N:O]B
A[N:O]/BA[N:O]
D32
DQS
DQS
DM
DQ [3:0]
RAS
ODT
CK
CKE
CK
DQS
DQS
DM
DQ [3:0]
CS
CK
CKE
ODT
ODT
CK
CKE
CK
WE
WE
A[N:O]/BA[N:O]
PCK0B
RCKE0B
RODT0B
RWEB
PCK0B
CK
WE
CAS
CAS
D7
CAS
RAS
CS
CS
RAS
RAS
CS
D16
A[N:O]/BA[N:O]
DQS
DQS
DM
DQ [3:0]
D4
A[N:O]/BA[N:O]
DQS7
DQS7
VSS
DQ[59:56]
ODT
DQS
DQS
DM
DQ [3:0]
CK
CKE
DQS16
DQS16
VSS
DQ[63:60]
CK
DQS
DQS
DM
DQ [3:0]
D14
CAS
DQS4
DQS4
VSS
DQ[35:32]
RAS
DQS
DQS
DM
DQ [3:0]
CS
DQS14
DQS14
VSS
DQ[47:44]
WE
RS0B
RRASB
RCASB
8GB, 1Gx72 Module(2Rank of x4) - page2
Vtt
VDDSPD
SPD
VDD
D0–D35
VTT
VREFCA
D0–D35
VREFDQ
D0–D35
VSS
D0–D35
D0–D35
VDDSPD
EVENT
SCL
SDA
VDDSPD
SA0
SA0
EVENT SPD with SA1
Integrated SA2
SCL
TS
VSS
SDA
SA1
SA2
VSS
Plan to use SPD with Integrated TS of Class B and
might be changed on customer’s requests. For more
details of SPD and Thermal sensor, please contact
local SK hynix sales representative
Note:
1. DQ-to-I/O wiring may be changed within a nibble.
2. See wiring diagrams for all resistors values.
3. ZQ pins of each SDRAM are connected to individual RZQ resistors (240+/-1%) ohms.
Rev. 1.0 / Jul. 2012
21
8GB, 1Gx72 Module(2Rank of x4) - page3
S0
1:2
S1
R
E
G
I
S
T
E
R
/
P
L
L
BA[N:0]
A[N:0]
RAS
CAS
WE
CKE0
CKE1
ODT0
ODT1
CK0
CK0
CK1
CK1
120 Ω
±5%
PAR_IN
RS0A → CS0: SDRAMs D[3:0], D[12:8], D17
RS0B → CS0: SDRAMs D[7:4], D[16:13]
RS1A → CS1: SDRAMs D[21:18], D[30:26], D35
RS1B → CS1: SDRAMs D[25:22], D[34:31]
RBA[N:0]A → BA[N:0]: SDRAMs D[3:0], D[12:8], D[21:17], D[30:26], D35
RBA[N:0]B → BA[N:0]: SDRAMs D[7:4], D[16:13], D[25:22], D[34:31]
RA[N:0]A → A[N:0]: SDRAMs D[3:0], D[12:8], D[21:17], D[30:26], D35
RA[N:0]B → A[N:0]: SDRAMs D[7:4], D[16:13], D[25:22], D[34:31]
RRASA → RAS: SDRAMs D[3:0], D[12:8], D[21:17], D[30:26], D35
RRASB → RAS: SDRAMs D[7:4], D[16:13], D[25:22], D[34:31]
RCASA → CAS: SDRAMs D[3:0], D[12:8], D[21:17], D[30:26], D35
RCASB → CAS: SDRAMs D[7:4], D[16:13], D[25:22], D[34:31]
RWEA → WE: SDRAMs D[3:0], D[12:8], D[21:17], D[30:26], D35
RWEB → WE: SDRAMs D[7:4], D[16:13], D[25:22], D[34:31]
RCKE0A → CKE0: SDRAMs D[3:0], D[12:8], D17
RCKE0B → CKE0: SDRAMs D[7:4], D[16:13]
RCKE1A → CKE1: SDRAMs D[21:18], D[30:26], D35
RCKE1B → CKE1: SDRAMs D[25:22], D[34:31]
RODT0A → ODT0: SDRAMs D[3:0], D[12:8], D17
RODT0B → ODT0: SDRAMs D[7:4], D[16:13]
RODT1A → ODT1: SDRAMs D[21:18], D[30:26], D35
RODT1A → ODT1: SDRAMs D[25:22], D[34:31]
PCK0A → CK: SDRAMs D[3:0], D[12:8], D17
PCK0B → CK: SDRAMs D[7:4], D[16:13]
PCK1A → CK: SDRAMs D[21:18], D[30:26], D35
PCK1B → CK: SDRAMs D[25:22], D[34:31]
PCK0A → CK: SDRAMs D[3:0], D[12:8], D17
PCK0B → CK: SDRAMs D[7:4], D[16:13]
PCK1A → CK: SDRAMs D[21:18], D[30:26], D35
PCK1B → CK: SDRAMs D[25:22], D[34:31]
Err_Out
RESET
RST
RST: SDRAMs D[35:0]
* S[3:2], CK1 and CK1 are NC
Rev. 1.0 / Jul. 2012
22
VSS
DQS0
DQS0
VSS
DQ[3:0]
ZQ
DQS
DQS
DM
DQ [3:0]
Rev. 1.0 / Jul. 2012
D1
ZQ
DQS
DQS
DM
DQ [3:0]
D0
D53
ZQ
DQS
DQS
DM
DQ [3:0]
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
D52
ODT
D50
ODT
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
D46
D48
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
D44
A[N:O]/BA[N:O]
ODT
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
VSS
CAS
VSS
RAS
CS
VSS
CAS
VSS
RAS
D51
A[N:O]/BA[N:O]
ODT
CK
WE
CAS
RAS
VSS
CS
D49
A[N:O]/BA[N:O]
ODT
CK
CKE
D47
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
CS
D45
A[N:O]/BA[N:O]
ODT
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
VSS
CAS
VSS
RAS
CS
VSS
RAS
CS
VSS
RAS
D2
A[N:O]/BA[N:O]
ODT
CK
WE
VSS
CS
D4
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
D6
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
D8
A[N:O]/BA[N:O]
ODT
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CAS
WE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
VSS
CAS
VSS
RAS
CS
VSS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CAS
WE
VSS
CAS
D3
A[N:O]/BA[N:O]
ODT
D5
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CAS
WE
D7
A[N:O]/BA[N:O]
CK
CKE
CK
CAS
WE
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
D9
RAS
CS
VSS
DQS1
DQS1
VSS
DQ[11:8]
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
VSS
CS
CS
VSS
DQS2
DQS2
VSS
DQ[19:16]
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
ODT
CS
VSS
DQS3
DQS3
VSS
DQ[27:24]
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
CS
VSS
DQS8
DQS8
VSS
CB[3:0]
CK
CAS
WE
RAS
CS
VDD
BRCKE1A
BRS3A
BRA[N:O]A
/BRBA[N:O]A
BRODT1A
BPCK0A
BRCKE0A
BPCK0A
BRWEA
BRCASA
BRS2A
BRRASA
VDD
ARCKE1A
ARS1A
ARA[N:O]A
/ARBA[N:O]A
ARODT0A
APCK0A
ARCKE0A
APCK0A
ARWEA
ARCASA
ARS0A
ARRASA
16GB, 2Gx72 Module(4Rank of x4) - page1
Vtt
23
VSS
DQS9
DQS9
VSS
DQ[7:4]
ZQ
DQS
DQS
DM
DQ [3:0]
Rev. 1.0 / Jul. 2012
D19
ZQ
DQS
DQS
DM
DQ [3:0]
D18
D71
ZQ
DQS
DQS
DM
DQ [3:0]
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
D70
ODT
D68
ODT
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
D64
D66
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
D62
A[N:O]/BA[N:O]
ODT
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
VSS
CAS
VSS
RAS
CS
VSS
CAS
VSS
RAS
D69
A[N:O]/BA[N:O]
ODT
CK
WE
CAS
RAS
VSS
CS
D67
A[N:O]/BA[N:O]
ODT
CK
CKE
D65
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
CS
D63
A[N:O]/BA[N:O]
ODT
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
VSS
CAS
VSS
RAS
CS
VSS
RAS
CS
VSS
RAS
D20
A[N:O]/BA[N:O]
ODT
CK
WE
VSS
CS
D22
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
D24
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
D26
A[N:O]/BA[N:O]
ODT
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CAS
WE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
VSS
CAS
VSS
RAS
CS
VSS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CAS
WE
VSS
CAS
D21
A[N:O]/BA[N:O]
ODT
D23
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CAS
WE
D25
A[N:O]/BA[N:O]
CK
CKE
CK
CAS
WE
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
D27
RAS
CS
VSS
DQS10
DQS10
VSS
DQ[15:12]
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
VSS
CS
CS
VSS
DQS11
DQS11
VSS
DQ[23:20]
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
ODT
CS
VSS
DQS12
DQS12
VSS
DQ[31:28]
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
CS
VSS
DQS17
DQS17
VSS
CB[7:4]
CK
CAS
WE
RAS
CS
VDD
BRCKE1A
BRS3A
BRA[N:O]A
/BRBA[N:O]A
BRODT1A
BPCK0A
BRCKE0A
BPCK0A
BRWEA
BRCASA
BRS2A
BRRASA
VDD
ARCKE1A
ARS1A
ARA[N:O]A
/ARBA[N:O]A
ARODT0A
APCK0A
ARCKE0A
APCK0A
ARWEA
ARCASA
ARS0A
ARRASA
16GB, 2Gx72 Module(4Rank of x4) - page2
Vtt
24
VSS
DQS7
DQS7
VSS
DQ[59:56]
ZQ
DQS
DQS
DM
DQ [3:0]
Rev. 1.0 / Jul. 2012
D17
D16
D37
ZQ
DQS
DQS
DM
DQ [3:0]
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
D36
ODT
CK
CKE
D38
ODT
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
D40
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
D42
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
VSS
RAS
CS
VSS
CAS
VSS
RAS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
VSS
CS
D39
A[N:O]/BA[N:O]
ODT
CK
CKE
D41
A[N:O]/BA[N:O]
ODT
CK
CKE
WE
CAS
RAS
CS
D13
A[N:O]/BA[N:O]
ODT
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
RAS
CS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
VSS
CAS
VSS
RAS
CS
VSS
RAS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
VSS
CS
D14
A[N:O]/BA[N:O]
ODT
D12
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
CAS
RAS
CS
D10
A[N:O]/BA[N:O]
ODT
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
CAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
CAS
RAS
CS
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CAS
WE
ZQ
DQS
DQS
DM
DQ [3:0]
CK
WE
VSS
CAS
VSS
RAS
CS
VSS
RAS
D15
A[N:O]/BA[N:O]
ODT
D13
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
CAS
WE
D11
A[N:O]/BA[N:O]
CK
CKE
CK
CAS
WE
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
VSS
CS
CS
VSS
DQS6
DQS6
VSS
DQ[51:48]
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
ODT
CS
VSS
DQS5
DQS5
VSS
DQ[43:40]
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
CS
VSS
DQS4
DQS4
VSS
DQ[35:32]
CK
CAS
WE
RAS
CS
VDD
BRCKE1B
BRS3B
BRA[N:O]B
/BRBA[N:O]B
BRODT1B
BPCK0B
BRCKE0B
BPCK0B
BRWEB
BRCASB
BRS2B
BRRASB
VDD
ARCKE1B
ARS1B
ARA[N:O]B
/ARBA[N:O]B
ARODT0B
APCK0B
ARCKE0B
APCK0B
ARWEB
ARCASB
ARS0B
ARRASB
16GB, 2Gx72 Module(4Rank of x4) - page3
Vtt
25
BRCKE1B
VDD
A[N:O]/BA[N:O]
CK
CKE
CK
ODT
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
ODT
ODT
ODT
CK
CKE
CK
CKE
CK
CKE
CAS
WE
WE
CK
CK
WE
WE
D54
CK
CS
RAS
RAS
CS
CAS
CAS
RAS
CS
D56
ZQ
DQS
DQS
DM
DQ [3:0]
CS
A[N:O]/BA[N:O]
D58
ZQ
DQS
DQS
DM
DQ [3:0]
CAS
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
ODT
ODT
CK
CKE
WE
D55
D60
ZQ
DQS
DQS
DM
DQ [3:0]
RAS
A[N:O]/BA[N:O]
CK
CKE
CK
ODT
ODT
CK
CKE
CK
CKE
VSS
ZQ
DQS
DQS
DM
DQ [3:0]
ZQ
DQS
DQS
DM
DQ [3:0]
A[N:O]/BA[N:O]
BRS3B
BRA[N:O]B
/BRBA[N:O]B
BPCK0B
BRCKE0B
BRODT1B
BRWEB
BPCK0B
BRCASB
D57
WE
CAS
RAS
CS
CK
WE
VSS
CK
CAS
RAS
CS
D59
CK
BRS2B
BRRASB
CAS
RAS
CS
WE
VSS
ZQ
DQS
DQS
DM
DQ [3:0]
CAS
ODT
CK
CKE
CK
WE
CAS
D34
A[N:O]/BA[N:O]
VSS
ZQ
DQS
DQS
DM
DQ [3:0]
D61
ZQ
DQS
DQS
DM
DQ [3:0]
CS
ODT
CK
CKE
CK
WE
CAS
D32
A[N:O]/BA[N:O]
VSS
VSS
ZQ
DQS
DQS
DM
DQ [3:0]
RAS
VDD
ODT
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
ODT
CK
CKE
CK
WE
D30
CAS
CS
RAS
RAS
CK
CKE
VSS
ZQ
DQS
DQS
DM
DQ [3:0]
CS
CK
WE
CAS
RAS
CS
D28
ZQ
DQS
DQS
DM
DQ [3:0]
CS
D35
A[N:O]/BA[N:O]
VSS
VSS
ZQ
DQS
DQS
DM
DQ [3:0]
RAS
A[N:O]/BA[N:O]
ODT
ODT
A[N:O]/BA[N:O]
A[N:O]/BA[N:O]
ODT
CK
CAS
WE
D33
ARCKE1B
ARS1B
ARA[N:O]B
/ARBA[N:O]B
ARODT0B
ARWEB
APCK0B
CK
CAS
WE
CK
CAS
WE
VSS
CAS
WE
RAS
CS
CS
RAS
RAS
CS
D31
ODT
ZQ
DQS
DQS
DM
DQ [3:0]
CK
CKE
VSS
DQS16
DQS16
VSS
DQ[63:60]
VSS
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
D29
CK
CKE
VSS
DQS15
DQS15
VSS
DQ[55:52]
VSS
CK
CKE
ZQ
DQS
DQS
DM
DQ [3:0]
APCK0B
ARCKE0B
ARCASB
VSS
DQS14
DQS14
VSS
DQ[47:44]
RAS
ZQ
DQS
DQS
DM
DQ [3:0]
CS
VSS
DQS13
DQS13
VSS
DQ[39:36]
CK
ARS0B
ARRASB
16GB, 2Gx72 Module(4Rank of x4) - page4
Vtt
VDDSPD
VDD
SPD
D0–D71
VTT
VREFCA
D0–D71
VREFDQ
D0–D71
VSS
D0–D71
VDDSPD
EVENT
SCL
SDA
VDDSPD
SA0
SA0
EVENT SPD with SA1
Integrated SA2
SCL
TS
SDA
VSS
SA1
SA2
VSS
Plan to use SPD with Integrated TS of Class B and
might be changed on customer’s requests. For more
details of SPD and Thermal sensor, please contact
local SK hynix sales representative
Note:
1. DQ-to-I/O wiring may be changed within a nibble.
2. Unless otherwise noted, resistor values are 15 Ohms ±5%.
3. See the wiring diagrams for all resistors associated with the command, address and
control bus.
4. ZQ resistors are 240 Ohms ±1%. For all other resistor values refer to the appropriate
wiring diagram.
Rev. 1.0 / Jul. 2012
26
16GB, 2Gx72 Module(4Rank of x4) - page5
S0
1:2
WE
R
E
G
I
S
T
E
R
/
P
L
L
CKE0
A
S1
BA[N:0]
A[N:0]
RAS
CAS
CKE1
ODT0
CK0
120 Ω
±5%
CK0
PAR_IN
RESET
ARS0A → CS1: SDRAMs D1,D3,D5,D7 D9,
D19, D21, D23, D25, D27
ARS0B → CS1: SDRAMs D11, D13, D15, D17,
D29, D31, D33, D35
S2
1:2
S3
ARS1A → CS0: SDRAMs D0, D2, D4, D6, D8,
D18, D20, D22, D24, D26
ARS1B → CS0: SDRAMs D10, D12, D14, D16,
D28, D30, D32, D34
ARBA[N:0]A → BA[N:0]: SDRAMs D[9:0],D[27:18] BA[N:0]
ARBA[N:0]B → BA[N:0]: SDRAMs D[17:10],D[35:28]
ARA[N:0]A → A[N:0]: SDRAMs D[9:0],D[27:18]
A[N:0]
ARA[N:0]B → A[N:0]: SDRAMs D[17:10],D[35:28]
RAS
ARRASA → RAS: SDRAMs D[9:0],D[27:18]
ARRASB → RAS: SDRAMs D[17:10],D[35:28]
ARCASA → CAS: SDRAMs D[9:0],D[27:18]
CAS
ARCASB → CAS: SDRAMs D[17:10],D[35:28]
ARWEA → WE: SDRAMs D[9:0],D[27:18]
WE
ARWEB → WE: SDRAMs D[17:10],D[35:28]
ARCKE0A → CKE1: SDRAMs D1,D3,D5,D7,D9,
CKE0
D19, D21, D23, D25, D27
ARCKE0B → CKE1: SDRAMs D11,D13,D15,D17,
D29, D31, D33, D35
CKE1
ARCKE1A → CKE0: SDRAMs D0,D2,D4,D6,D8,
D18, D20, D22, D24, D26
ARCKE1B → CKE0: SDRAMs D10,D12,D14,D16,
D28, D30, D32, D34
ARODT0A → ODT1: SDRAMs D1,D3,D5,D7,D9,
ODT1
D19, D21, D23, D25, D27
ARODT0B → ODT0: SDRAMs D11,D13,D15,D17,
D29, D31, D33, D35
APCK0A → CK: SDRAMs D[9:0]
CK0
APCK0B → CK: SDRAMs D[17:10]
120 Ω
APCK1A → CK: SDRAMs D[27:18]
±5%
APCK1B → CK: SDRAMs D[35:28]
APCK0A → CK: SDRAMs D[9:0]
CK0
APCK0B → CK: SDRAMs D[17:10]
APCK1A → CK: SDRAMs D[27:18]
APCK1B → CK: SDRAMs D[35:28]
Err_Out
RST
R
E
G
I
S
T
E
R
/
P
L
L
B
PAR_IN
RESET
BRS2A → CS1: SDRAMs D45,D47,D49,D51,D53
D63,D65,D67,D69,D71
BRS2B → CS1: SDRAMs D37,D39,D41,D43,
D55,D57,D59,D61
BRS3A → CS0: SDRAMs D44.D46,D48,D50,D52,
D62,D64,D66,D68,D70
BRS3B → CS0: SDRAMs D36,D38,D40,D42,
D54,D56,D58,D60
BRBA[N:0]A → BA[N:0]: SDRAMs D[53:44],D[71:62]
BRBA[N:0]B → BA[N:0]: SDRAMs D[43:36],D[61:54]
BRA[N:0]A → A[N:0]: SDRAMs D[55:44],D[71:62]
BRA[N:0]B → A[N:0]: SDRAMs D[43:36],D[61:54]
BRRASA → RAS: SDRAMs D[53:44],D[71:62]
BRRASB → RAS: SDRAMs D[43:36],D[61:54]
BRCASA → CAS: SDRAMs D[53:44],D[71:62]
BRCASB → CAS: SDRAMs D[43:36],D[61:54]
BRWEA → WE: SDRAMs D[53:44],D[71:62]
BRWEB → WE: SDRAMs D[43:36],D[61:54]
BRCKE0A → CKE1: SDRAMs D45,D47,D49,D51,D53,
D63,D65,D67,D69,D71
BRCKE0B → CKE1: SDRAMs D37,D39,D41,D43,
D55,D57,D59,D61
BRCKE1A → CKE0: SDRAMs D44.D46,D48,D50,D52,
D62,D64,D66,D68,D70
BRCKE1B → CKE0: SDRAMs D36,D38,D40,D42,
D54,D56,D58,D60
BRODT1A → ODT1: SDRAMs D45,D47,D49,D51,D53
D63,D65,D67,D69,D71
BRODT1B → ODT0: SDRAMs D37,D39,D41,D43
D55,D57,D59,D61
BPCK0A → CK: SDRAMs D[53:44]
BPCK0B → CK: SDRAMs D[43:36]
BPCK1A → CK: SDRAMs D[71:62]
BPCK1B → CK: SDRAMs D[61:54]
BPCK0A → CK: SDRAMs D[53:44]
BPCK0B → CK: SDRAMs D[43:36]
BPCK1A → CK: SDRAMs D[71:62]
BPCK1B → CK: SDRAMs D[61:54]
Err_Out
RST
RST: SDRAMs D[35:0]
CK1
CK1
120 Ω
±5%
1. CK0 and CK0 are differentially terminated with a single 120 Ohms ±5% resistor.
2. CK1 and CK1 are differentially terminated with a single 120 Ohms ±5% resistor, but is not used.
3. Unused register inputs ODT1 for Register A and ODT0 for Register B are tied to ground.
4. The module drawing on this page is not drawn to scale.
Rev. 1.0 / Jul. 2012
27
Absolute Maximum Ratings
Absolute Maximum DC Ratings
Absolute Maximum DC Ratings
Symbol
VDD
VDDQ
Parameter
Rating
Units
Notes
Voltage on VDD pin relative to Vss
- 0.4 V ~ 1.80 V
V
1,3
Voltage on VDDQ pin relative to Vss
- 0.4 V ~ 1.80 V
V
1,3
- 0.4 V ~ 1.80 V
V
1
C
1, 2
VIN, VOUT Voltage on any pin relative to Vss
TSTG
-55 to +100
Storage Temperature
o
Notes:
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
2. Storage Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement
conditions, please refer to JESD51-2 standard.
3. VDD and VDDQ must be within 300mV of each other at all times; and VREF must not be greater than
0.6XVDDQ,When VDD and VDDQ are less than 500mV; VREF may be equal to or less than 300mV.

DRAM Component Operating Temperature Range
Temperature Range
Symbol
TOPER
Parameter
Rating
Units
Notes
Normal Operating Temperature Range
0 to 85
oC
1,2
Extended Temperature Range
85 to 95
oC
1,3
Notes:
1. Operating Temperature TOPER is the case surface temperature on the center / top side of the DRAM. For measurement conditions, please refer to the JEDEC document JESD51-2.
2. The Normal Temperature Range specifies the temperatures where all DRAM specifications will be supported. During operation, the DRAM case temperature must be maintained between 0 - 85oC under all operating conditions.
3. Some applications require operation of the DRAM in the Extended Temperature Range between 85oC and 95oC
case temperature. Full specifications are guaranteed in this range, but the following additional conditions apply:
a. Refresh commands must be doubled in frequency, therefore reducing the Refresh interval tREFI to 3.9 µs. It
is also possible to specify a component with 1X refresh (tREFI to 7.8µs) in the Extended Temperature Range.
Please refer to the DIMM SPD for option availability
b. If Self-Refresh operation is required in the Extended Temperature Range, then it is mandatory to either use
the Manual Self-Refresh mode with Extended Temperature Range capability (MR2 A6 = 0b and MR2 A7 = 1b)
or enable the optional Auto Self-Refresh mode (MR2 A6 = 1b and MR2 A7 = 0b). DDR3 SDRAMs support Auto
Self-Refresh and in Extended Temperature Range and please refer to component datasheet and/or the DIMM
SPD for tREFI requirements in the Extended Temperature Range
Rev. 1.0 / Jul. 2012
28
AC & DC Operating Conditions
Recommended DC Operating Conditions
Recommended DC Operating Conditions
Symbol
VDD
VDDQ
Parameter
Rating
Units
Notes
1.575
V
1,2
1.575
V
1,2
Min.
Typ.
Max.
Supply Voltage
1.425
1.500
Supply Voltage for Output
1.425
1.500
Notes:
1. Under all conditions, VDDQ must be less than or equal to VDD.
2. VDDQ tracks with VDD. AC parameters are measured with VDD and VDDQ tied together.
Rev. 1.0 / Jul. 2012
29
AC & DC Input Measurement Levels
AC and DC Logic Input Levels for Single-Ended Signals
AC and DC Input Levels for Single-Ended Command and Address Signals
Single Ended AC and DC Input Levels for Command and ADDress
DDR3-800/1066/1333/1600
Symbol
Min
VIH.CA(DC100)
VIL.CA(DC100)
VIH.CA(AC175)
VIL.CA(AC175)
VIH.CA(AC150)
VIL.CA(AC150)
VIH.CA(AC135)
VIL.CA(AC135)
VIH.CA(AC125)
VIL.CA(AC125)
VRefCA(DC)
DDR3-1866
Parameter
DC input logic high
Vref + 0.100
DC input logic low
VSS
AC input logic high
Vref + 0.175
AC input logic low
Note2
AC Input logic high
Vref + 0.150
AC input logic low
Note2
AC input logic high
AC input logic low
AC Input logic high
AC input logic low
Reference Voltage for
0.49 * VDD
ADD, CMD inputs
Unit
Notes
VDD
Vref - 0.100
Note2
Vref - 0.135
Note2
Vref - 0.125
V
V
V
V
V
V
V
V
V
V
1, 5
1, 6
1, 2, 7
1, 2, 8
1, 2, 7
1, 2, 8
1, 2, 7
1, 2, 8
1, 2, 7
1, 2, 8
0.51 * VDD
V
3, 4
Max
Min
Max
VDD
Vref - 0.100
Note2
Vref - 0.175
Note2
Vref - 0.150
-
Vref + 0.100
VSS
Vref + 0.135
Note2
Vref + 0.125
Note2
0.51 * VDD
0.49 * VDD
Notes:
1. For input only pins except RESET, Vref = VrefCA (DC).
2. Refer to "Overshoot and Undershoot Specifications" on page 43.
3. The ac peak noise on VRef may not allow VRef to deviate from VRefCA(DC) by more than +/-1% VDD (for
reference: approx. +/- 15 mV).
4. For reference: approx. VDD/2 +/- 15 mV.
5. VIH(dc) is used as a simplified symbol for VIH.CA(DC100)
6. VIL(dc) is used as a simplified symbol for VIL.CA(DC100)
7. VIH(ac) is used as simplified symbol for VIH.CA(AC175), VIH.CA(AC150), VIH.CA(AC135), and
VIH.CA(AC125); VIH.CA(AC175) value is used when Vref + 0.175V is referenced, VIH.CA(AC150) value is
used when Vref + 0.150V is referenced, VIH.CA(AC135) value is used when Vref + 0.135V is referenced,
and VIH.CA(AC125) value is used when Vref + 0.125V is referenced.
8. VIL(ac) is used as simplified symbol for VIL.CA(AC175), VIL.CA(AC150), VIL.CA(AC135), and
VIL.CA(AC125); VIL.CA(AC175) value is used when Vref - 0.175V is referenced, VIL.CA(AC150) value is
used when Vref - 0.150V is referenced, VIL.CA(AC135) value is used when Vref - 0.135V is referenced, and
VIL.CA(AC125) value is used when Vref - 0.125V is referenced.
Rev. 1.0 / Jul. 2012
30
AC and DC Input Levels for Single-Ended Signals
DDR3 SDRAM will support two Vih/Vil AC levels for DDR3-800 and DDR3-1066 as specified in the table
below. DDR3 SDRAM will also support corresponding tDS values (Table 41 and Table 47 in “ DDR3 Device
Operation”) as well as derating tables in Table 44 of “DDR3 Device Operation” depending on Vih/Vil AC levels.
Single Ended AC and DC Input Levels for DQ and DM
Symbol
VIH.DQ(DC100)
VIL.DQ(DC100)
VIH.DQ(AC175)
VIL.DQ(AC175)
VIH.DQ(AC150)
VIL.DQ(AC150)
VIH.CA(AC135)
VIL.CA(AC135)
VRefDQ(DC)
DDR3-800/1066
DDR3-1333/1600
Min
Min
DDR3-1866
Parameter
DC input logic high
DC input logic low
AC input logic high
AC input logic low
AC Input logic high
AC input logic low
AC input logic high
AC input logic low
Reference Voltage
for DQ, DM inputs
Unit Notes
Max
Max
Min
Max
Vref + 0.100
VDD
Vref + 0.100
VDD
Vref + 0.100
VDD
V
1, 5
VSS
Vref - 0.100
VSS
Vref - 0.100
VSS
Vref - 0.100 V
1, 6
Vref + 0.175 Note2
V 1, 2, 7
Note2
Vref - 0.175
V 1, 2, 8
Vref + 0.150 Note2 Vref + 0.150 Note2 Vref + 0.150 Note2
V 1, 2, 7
Note2
Vref - 0.150
Note2
Vref - 0.150
Note2
Vref - 0.150 V 1, 2, 8
Vref + 0.135 Note2
mV 1, 2, 7
Note2
Vref - 0.135 mV 1, 2, 8
0.49 * VDD 0.51 * VDD 0.49 * VDD 0.51 * VDD 0.49 * VDD 0.51 * VDD
V
3, 4
Notes:
1. Vref = VrefDQ (DC).
2. Refer to "Overshoot and Undershoot Specifications" on page 43.
3. The ac peak noise on VRef may not allow VRef to deviate from VRefDQ(DC) by more than +/-1% VDD (for
reference: approx. +/- 15 mV).
4. For reference: approx. VDD/2 +/- 15 mV.
5. VIH(dc) is used as a simplified symbol for VIH.DQ(DC100)
6. VIL(dc) is used as a simplified symbol for VIL.DQ(DC100)
7. VIH(ac) is used as simplified symbol for VIH.DQ(AC175), VIH.DQ(AC150), and VIH.DQ(AC135);
VIH.DQ(AC175) value is used when Vref + 0.175V is referenced, VIH.DQ(AC150) value is used when Vref
+ 0.150V is referenced, and VIH.DQ(AC135) value is used when Vref + 0.135V is referenced.
8. VIL(ac) is used as simplified symbol for VIL.DQ(AC175), VIL.DQ(AC150), and VIL.DQ(AC135);
VIL.DQ(AC175) value is used when Vref - 0.175V is referenced, VIL.DQ(AC150) value is used when Vref 0.150V is referenced, and VIL.DQ(AC135) value is used when Vref - 0.135V is referenced.
Rev. 1.0 / Jul. 2012
31
Vref Tolerances
The dc-tolerance limits and ac-noise limits for the reference voltages VRefCA and VRefDQ are illustrated in
figure below. It shows a valid reference voltage VRef (t) as a function of time. (VRef stands for VRefCA and
VRefDQ likewise).
VRef (DC) is the linear average of VRef (t) over a very long period of time (e.g. 1 sec). This average has to
meet the min/max requirements in the table "Differential Input Slew Rate Definition" on page 38. Furthermore VRef (t) may temporarily deviate from VRef (DC) by no more than +/- 1% VDD.
voltage
VDD
VRef ac-noise
VRef(DC)
VRef(t)
VRef(DC)max
VDD/2
VRef(DC)min
VSS
time
Illustration of VRef(DC) tolerance and VRef ac-noise limits
The voltage levels for setup and hold time measurements VIH(AC), VIH(DC), VIL(AC), and VIL(DC) are dependent on VRef.
“VRef ” shall be understood as VRef(DC), as defined in figure above.
This clarifies that dc-variations of VRef affect the absolute voltage a signal has to reach to achieve a valid
high or low level and therefore the time to which setup and hold is measured. System timing and voltage
budgets need to account for VRef(DC) deviations from the optimum position within the data-eye of the input
signals.
This also clarifies that the DRAM setup/hold specification and derating values need to include time and
voltage associated with VRefac-noise. Timing and voltage effects due to ac-noise on VRef up to the specified limit (+/- 1% of VDD) are included in DRAM timings and their associated deratings.
Rev. 1.0 / Jul. 2012
32
AC and DC Logic Input Levels for Differential Signals
Differential signal definition
tDVAC
Differential Input Voltage(i.e.DQS - DQS#, CK - CK#)
VIL.DIFF.AC.MIN
VIL.DIFF.MIN
0
half cycle
VIL.DIFF.MAX
VIL.DIFF.AC.MAX
tDVAC
time
Definition of differential ac-swing and “time above ac-level” tDVAC
Rev. 1.0 / Jul. 2012
33
Differential swing requirements for clock (CK - CK) and strobe (DQS-DQS)
Differential AC and DC Input Levels
DDR3-800, 1066, 1333, 1600
Symbol
Parameter
VIHdiff
VILdiff
VIHdiff (ac)
VILdiff (ac)
Unit Notes
Differential input high
Differential input logic low
Differential input high ac
Differential input low ac
Min
Max
+ 0.180
Note 3
2 x (VIH (ac) - Vref)
Note 3
Note 3
- 0.180
Note 3
2 x (VIL (ac) - Vref)
V
V
V
V
1
1
2
2
Notes:
1. Used to define a differential signal slew-rate.
2. For CK - CK use VIH/VIL (ac) of AADD/CMD and VREFCA; for DQS - DQS, DQSL, DQSL, DQSU, DQSU use VIH/VIL
(ac) of DQs and VREFDQ; if a reduced ac-high or ac-low levels is used for a signal group, then the reduced level
applies also here.
3. These values are not defined; however, the single-ended signals Ck, CK, DQS, DQS, DQSL, DQSL, DQSU, DQSU
need to be within the respective limits (VIH (dc) max, VIL (dc) min) for single-ended signals as well as the limitations for overshoot and undershoot. Refer to "Overshoot and Undershoot Specifications" on page 43.
Allowed time before ringback (tDVAC) for CK - CK and DQS - DQS
DDR3-800/1066/1333/1600
Slew Rate
[V/ns]
tDVAC [ps]
@ VIH/Ldiff (ac)
= 350mV
min
max
tDVAC [ps]
@ VIH/Ldiff (ac)
= 300mV
min
max
DDR3-1866
tDVAC [ps]
@ VIH/Ldiff (ac)
= 270mV
(DQS-DQS)only
(Optional)
min
max
tDVAC [ps]
@ VIH/Ldiff (ac|
= 270mV
min
max
> 4.0
75
-
175
-
214
-
134
-
4.0
57
-
170
-
214
-
134
-
3.0
50
-
167
-
191
-
112
-
2.0
38
-
119
1.8
34
-
102
-
131
-
52
-
1.6
29
-
81
-
113
-
33
-
1.4
22
-
54
-
88
-
9
-
1.2
note
-
19
-
56
-
note
-
1.0
note
-
note
-
11
-
note
-
< 1.0
note
-
note
-
note
-
note
-
146
67
note : Rising input differential signal shall become equal to or greater than VIHdiff(ac) level and Falling
input differential signal shall become equal to or less than VIL(ac) level.
Rev. 1.0 / Jul. 2012
34
Single-ended requirements for differential signals
Each individual component of a differential signal (CK, DQS, DQSL, DQSU, CK, DQS, DQSL, of DQSU) has
also to comply with certain requirements for single-ended signals.
CK and CK have to approximately reach VSEHmin / VSELmax (approximately equal to the ac-levels (VIH
(ac) / VIL (ac)) for ADD/CMD signals) in every half-cycle.
DQS, DQSL, DQSU, DQS, DQSL have to reach VSEHmin / VSELmax (approximately the ac-levels (VIH (ac)
/ VIL (ac)) for DQ signals) in every half-cycle preceding and following a valid transition.
Note that the applicable ac-levels for ADD/CMD and DQ’s might be different per speed-bin etc. E.g., if
VIH.CA(AC150)/VIL.CA(AC150) is used for ADD/CMD signals, then these ac-levels apply also for the singleended signals CK and CK.
VDD or VDDQ
VSEHmin
VSEH
VDD/2 or VDDQ/2
CK or DQS
VSELmax
VSS or VSSQ
VSEL
time
Single-ended requirements for differential signals.
Note that, while ADD/CMD and DQ signal requirements are with respect to Vref, the single-ended components of differential signals have a requirement with respect to VDD / 2; this is nominally the same. the
transition of single-ended signals through the ac-levels is used to measure setup time. For single-ended
components of differential signals the requirement to reach VSELmax, VSEHmin has no bearing on timing,
but adds a restriction on the common mode characteristics of these signals.
Rev. 1.0 / Jul. 2012
35
Single-ended levels for CK, DQS, DQSL, DQSU, CK, DQS, DQSL or DQSU
DDR3-800, 1066, 1333, 1600
Symbol
VSEH
VSEL
Parameter
Single-ended high level for strobes
Single-ended high level for Ck, CK
Single-ended low level for strobes
Single-ended low level for CK, CK
Unit Notes
Min
Max
(VDD / 2) + 0.175
(VDD /2) + 0.175
Note 3
Note 3
Note 3
Note 3
(VDD / 2) = 0.175
(VDD / 2) = 0.175
V
V
V
V
1,2
1,2
1,2
1,2
Notes:
1. For CK, CK use VIH/VIL (ac) of ADD/CMD; for strobes (DQS, DQS, DQSL, DQSL, DQSU, DQSU) use VIH/VIL (ac)
of DQs.
2. VIH (ac)/VIL (ac) for DQs is based on VREFDQ; VIH (ac)/VIL (ac) for ADD/CMD is based on VREFCA; if a reduced
ac-high or ac-low level is used for a signal group, then the reduced level applies also here.
3. These values are not defined; however, the single-ended signals Ck, CK, DQS, DQS, DQSL, DQSL, DQSU, DQSU
need to be within the respective limits (VIH (dc) max, VIL (dc) min) for single-ended signals as well as the limitations for overshoot and undershoot. Refer to "Overshoot and Undershoot Specifications" on page 43.
Rev. 1.0 / Jul. 2012
36
Differential Input Cross Point Voltage
To guarantee tight setup and hold times as well as output skew parameters with respect to clock and
strobe, each cross point voltage of differential input signals (CK, CK and DQS, DQS) must meet the
requirements in table below. The differential input cross point voltage VIX is measured from the actual
cross point of true and complement signals to the midlevel between of VDD and VSS
Vix Definition
Cross point voltage for differential input signals (CK, DQS)
DDR3-800, 1066, 1333, 1600 & 1866
Symbol
VIX
VIX
Parameter
Differential Input Cross Point Voltage
relative to VDD/2 for CK, CK
Differential Input Cross Point Voltage
relative to VDD/2 for DQS, DQS
Unit Notes
Min
Max
-150
150
mV
1
-150
150
mV
1
Notes:
1. The relation between Vix Min/Max and VSEL/VSEH should satisfy following.
(VDD/2) + Vix (Min) - VSEL  25mV 
VSEH - ((VDD/2) + Vix (Max))  25mV
Rev. 1.0 / Jul. 2012
37
Slew Rate Definitions for Single-Ended Input Signals
See 7.5 “Address / Command Setup, Hold and Derating” on page 134 in “DDR3 Device Operation” for single-ended slew rate definitions for address and command signals.

See 7.6 “Data Setup, Hold and Slew Rate Derating” on page 142 in “DDR3 Device Operation” for singleended slew rate definition for data signals.
Slew Rate Definitions for Differential Input Signals
Input slew rate for differential signals (CK, CK and DQS, DQS) are defined and measured as shown in table
and figure below.
Differential Input Slew Rate Definition
Measured
Description
Min
Differential input slew rate for rising edge
(CK-CK and DQS-DQS)
Differential input slew rate for falling edge
(CK-CK and DQS-DQS)
Defined by
Max
VILdiffmax
VIHdiffmin [VIHdiffmin-VILdiffmax] / DeltaTRdiff
VIHdiffmin
VILdiffmax [VIHdiffmin-VILdiffmax] / DeltaTFdiff
Notes:
Differential Input Voltage (i.e. DQS-DQS; CK-CK)
The differential signal (i.e. CK-CK and DQS-DQS) must be linear between these thresholds.
Delta
TRdiff
vIHdiffmin
0
vILdiffmax
Delta
TFdiff
Differential Input Slew Rate Definition for DQS, DQS# and CK, CK#
Differential Input Slew Rate Definition for DQS, DQS and CK, CK
Rev. 1.0 / Jul. 2012
38
AC & DC Output Measurement Levels
Single Ended AC and DC Output Levels
Table below shows the output levels used for measurements of single ended signals.
Single-ended AC and DC Output Levels
Symbol
Parameter
VOH(DC)
DC output high measurement level (for IV curve linearity)
VOM(DC)
DC output mid measurement level (for IV curve linearity)
VOL(DC)
VOH(AC)
DDR3-800, 1066,
1333 and 1600
0.8 x VDDQ
Unit
Notes
V
V
DC output low measurement level (for IV curve linearity)
0.5 x VDDQ
0.2 x VDDQ
AC output high measurement level (for output SR)
VTT + 0.1 x VDDQ
V
1
AC output low measurement level (for output SR)
VTT - 0.1 x VDDQ
V
1
VOL(AC)
V
Notes:
1. The swing of ±0.1 x VDDQ is based on approximately 50% of the static single ended output high or low
swing with a driver impedance of 40 Ω and an effective test load of 25 Ω to VTT = VDDQ / 2.
Differential AC and DC Output Levels
Table below shows the output levels used for measurements of single ended signals.
Differential AC and DC Output Levels
DDR3-800, 1066,
Symbol
Parameter
VOHdiff (AC)
AC differential output high measurement level (for output SR)
1333 and 1600
+ 0.2 x VDDQ
VOLdiff (AC)
AC differential output low measurement level (for output SR)
- 0.2 x VDDQ
Unit
Notes
V
1
V
1
Notes:
1. The swing of ±0.2 x VDDQ is based on approximately 50% of the static differential output high or low
swing with a driver impedance of 40 Ω and an effective test load of 25 Ω to VTT = VDDQ/2 at each of the
differential outputs.
Rev. 1.0 / Jul. 2012
39
Single Ended Output Slew Rate
When the Reference load for timing measurements, output slew rate for falling and rising edges is defined
and measured between VOL(AC) and VOH(AC) for single ended signals are shown in table and figure below.
Single-ended Output slew Rate Definition
Measured
Description
Defined by
From
To
Single-ended output slew rate for rising edge
VOL(AC)
VOH(AC)
[VOH(AC)-VOL(AC)] / DeltaTRse
Single-ended output slew rate for falling edge
VOH(AC)
VOL(AC)
[VOH(AC)-VOL(AC)] / DeltaTFse
Notes:
1. Output slew rate is verified by design and characterisation, and may not be subject to production test.
Single Ended Output Voltage(l.e.DQ)
Delta TRse
vOH(AC)
V∏
vOl(AC)
Delta TFse
Single Ended Output Slew Rate Definition
Single Ended Output slew Rate Definition
Output Slew Rate (single-ended)
DDR3-800 DDR3-1066 DDR3-1333 DDR3-1600 DDR3-1866
Parameter
Single-ended Output Slew Rate
Symbol Min
SRQse
2.5
Max
Min
Max
Min
Max
Min
Max
Min
Max
5
2.5
5
2.5
5
2.5
5
2.5
51)
Units
V/ns
Description: SR; Slew Rate
Q: Query Output (like in DQ, which stands for Data-in, Query-Output)
se: Single-ended Signals
For Ron = RZQ/7 setting
Note 1): In two cases, a maximum slew rate of 6V/ns applies for a single DQ signal within a byte lane.
Case 1 is a defined for a single DQ signal within a byte lane which is switching into a certain direction (either from high
to low or low to high) while all remaining DQ signals in the same byte lane are static (i.e. they stay at either high or low).
Case 2 is a defined for a single DQ signal within a byte lane which is switching into a certain direction (either from high
to low or low to high) while all remaining DQ signals in the same byte lane switching into the opposite direction (i.e. from
low to high of high to low respectively). For the remaining DQ signal switching in to the opposite direction, the regular
maximum limite of 5 V/ns applies.
Rev. 1.0 / Jul. 2012
40
Differential Output Slew Rate
With the reference load for timing measurements, output slew rate for falling and rising edges is defined
and measured between VOLdiff (AC) and VOHdiff (AC) for differential signals as shown in table and figure
below.
Differential Output Slew Rate Definition
Measured
Description
Defined by
From
To
Differential output slew rate for rising edge
VOLdiff (AC)
VOHdiff (AC)
[VOHdiff (AC)-VOLdiff (AC)] / DeltaTRdiff
Differential output slew rate for falling edge
VOHdiff (AC)
VOLdiff (AC)
[VOHdiff (AC)-VOLdiff (AC)] / DeltaTFdiff
Notes:
1. Output slew rate is verified by design and characterization, and may not be subject to production test.
Differential Output Voltage(i.e. DQS-DQS)
Delta
TRdiff
vOHdiff(AC)
O
vOLdiff(AC)
Delta
TFdiff
Differential Output Slew Rate Definition
Differential Output slew Rate Definition
Differential Output Slew Rate
DDR3-800
DDR3-1066 DDR3-1333 DDR3-1600 DDR3-1866
Parameter
Symbol
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Differential Output Slew Rate
SRQdiff
5
12
5
12
5
12
5
12
5
12
Units
V/ns
Description: SR; Slew Rate
Q: Query Output (like in DQ, which stands for Data-in, Query-Output)
se: Single-ended Signals
For Ron = RZQ/7 setting
Rev. 1.0 / Jul. 2012
41
Reference Load for AC Timing and Output Slew Rate
Figure below represents the effective reference load of 25 ohms used in defining the relevant AC timing
parameters of the device as well as output slew rate measurements.
It is not intended as a precise representation of any particular system environment or a depiction of the
actual load presented by a production tester. System designers should use IBIS or other simulation tools to
correlate the timing reference load to a system environment. Manufacturers correlate to their production
test conditions, generally one or more coaxial transmission lines terminated at the tester electronics.
VDDQ
CK, CK
DUT
DQ
DQS
DQS
25 Ohm
VTT = VDDQ/2
Reference Load for AC Timing and Output Slew Rate
Rev. 1.0 / Jul. 2012
42
Overshoot and Undershoot Specifications
Address and Control Overshoot and Undershoot Specifications
AC Overshoot/Undershoot Specification for Address and Control Pins
DDR3- DDR3- DDR3- DDR3- DDR3-
Parameter
800
Maximum peak amplitude allowed for overshoot area. (See Figure below)
Maximum peak amplitude allowed for undershoot area. (See Figure below)
Maximum overshoot area above VDD (See Figure below)
Maximum undershoot area below VSS (See Figure below)
1066 1333
0.4
0.4
0.67
0.67
0.4
0.4
0.5
0.5
0.4
0.4
0.4
0.4
1600 1866
0.4
0.4
0.33
0.33
Units
0.4
V
0.4
V
0.28 V-ns
0.28 V-ns
(A0-A15, BA0-BA3, CS, RAS, CAS, WE, CKE, ODT)
See figure below for each parameter definition
M axim um A m plitude
O vershoot A rea
V olts
(V)
VDD
V SS
U ndershoot Area
M axim um A m plitud e
Tim e (ns)
Add ress and Control O vershoot and U ndershoot D efinition
Address and Control Overshoot and Undershoot Definition
Rev. 1.0 / Jul. 2012
43
Clock, Data, Strobe and Mask Overshoot and Undershoot Specifications
AC Overshoot/Undershoot Specification for Clock, Data, Strobe and Mask
DDR3- DDR3- DDR3- DDR3- DDR3-
Parameter
Maximum peak amplitude allowed for overshoot area. (See Figure below)
Maximum peak amplitude allowed for undershoot area. (See Figure below)
Maximum overshoot area above VDD (See Figure below)
Maximum undershoot area below VSS (See Figure below)
800
1066 1333 1600 1866
0.4
0.4
0.25
0.25
0.4
0.4
0.19
0.19
0.4
0.4
0.15
0.15
0.4
0.4
0.13
0.13
Units
0.4
V
0.4
V
0.11 V-ns
0.11 V-ns
(CK, CK, DQ, DQS, DQS, DM)
See figure below for each parameter definition
M a x im u m A m p litu d e
O v e rs h o o t A re a
V o lts
(V )
VDDQ
VSSQ
U n d e rs h o o t A re a
M a x im u m A m p litu d e
T im e (n s )
C lo c k , D a ta S tro b e a n d M a s k O v e rs h o o t a n d U n d e rs h o o t D e fin itio n
Clock, Data, Strobe and Mask Overshoot and Undershoot Definition
Rev. 1.0 / Jul. 2012
44
Refresh parameters by device density
Refresh parameters by device density
Parameter
REF command ACT or
REF command time
Average periodic
refresh interval
Rev. 1.0 / Jul. 2012
RTT_Nom Setting
512Mb
1Gb
2Gb
4Gb
8Gb
tRFC
90
110
160
260
350
ns
7.8
7.8
7.8
7.8
7.8
us
3.9
3.9
3.9
3.9
3.9
us
tREFI
0 C  TCASE  85 C
85 C  TCASE  95 C
Units Notes
1
45
Standard Speed Bins
DDR3 SDRAM Standard Speed Bins include tCK, tRCD, tRP, tRAS and tRC for each corresponding bin.
DDR3-800 Speed Bins
For specific Notes See "Speed Bin Table Notes" on page 51.
Speed Bin
DDR3-800E
CL - nRCD - nRP
6-6-6
Unit
Parameter
Symbol
min
max
Internal read command to first data
tAA
15
20
ns
ACT to internal read or write delay time
tRCD
15
—
ns
PRE command period
tRP
15
—
ns
ACT to ACT or REF command period
tRC
52.5
—
ns
ACT to PRE command period
tRAS
37.5
9 * tREFI
ns
tCK(AVG)
2.5
3.3
ns
CL = 6
CWL = 5
Supported CL Settings
6
nCK
Supported CWL Settings
5
nCK
Rev. 1.0 / Jul. 2012
Notes
1,2,3
46
DDR3-1066 Speed Bins
For specific Notes See "Speed Bin Table Notes" on page 51.
Speed Bin
DDR3-1066F
CL - nRCD - nRP
Parameter
Symbol
Unit
7-7-7
min
max
Note
Internal read command to
first data
tAA
13.125
20
ns
ACT to internal read or
write delay time
tRCD
13.125
—
ns
PRE command period
tRP
13.125
—
ns
ACT to ACT or REF
command period
tRC
50.625
—
ns
ACT to PRE command
period
tRAS
37.5
9 * tREFI
ns
CWL = 5
tCK(AVG)
2.5
3.3
ns
1,2,3,6
CWL = 6
tCK(AVG)
Reserved
ns
1,2,3,4
CWL = 5
tCK(AVG)
Reserved
ns
4
CWL = 6
tCK(AVG)
ns
1,2,3,4
CWL = 5
tCK(AVG)
ns
4
CWL = 6
tCK(AVG)
ns
1,2,3
CL = 6
CL = 7
CL = 8
1.875
< 2.5
Reserved
1.875
< 2.5
Supported CL Settings
6, 7, 8
nCK
Supported CWL Settings
5, 6
nCK
Rev. 1.0 / Jul. 2012
47
DDR3-1333 Speed Bins
For specific Notes See "Speed Bin Table Notes" on page 51.
Speed Bin
DDR3-1333H
CL - nRCD - nRP
Parameter
Symbol
Unit
9-9-9
min
max
Note
Internal read
command to first data
tAA
13.5
(13.125)5,10
20
ns
ACT to internal read or
write delay time
tRCD
13.5
(13.125)5,10
—
ns
PRE command period
tRP
13.5
(13.125)5,10
—
ns
ACT to ACT or REF
command period
tRC
49.5
(49.125)5,10
—
ns
ACT to PRE command
period
tRAS
36
9 * tREFI
ns
CWL = 5
tCK(AVG)
2.5
3.3
ns
1,2,3,7
CWL = 6
tCK(AVG)
Reserved
ns
1,2,3,4,7
CWL = 7
tCK(AVG)
Reserved
ns
4
CWL = 5
tCK(AVG)
Reserved
ns
4
CWL = 6
tCK(AVG)
ns
1,2,3,4,7
CWL = 7
tCK(AVG)
Reserved
ns
1,2,3,4
CWL = 5
tCK(AVG)
Reserved
ns
4
CWL = 6
tCK(AVG)
ns
1,2,3,7
CWL = 7
tCK(AVG)
Reserved
ns
1,2,3,4
CWL = 5, 6
tCK(AVG)
Reserved
ns
4
CL = 6
CL = 7
CL = 8
CL = 9
CWL = 7
tCK(AVG)
CWL = 5, 6
tCK(AVG)
CWL = 7
tCK(AVG)
1.875
< 2.5
5,10
(Optional)
1.875
< 2.5
ns
1,2,3,4
ns
4
(Optional)
ns
ns
1,2,3
5
Supported CL Settings
6, 7, 8, 9, 10
nCK
Supported CWL Settings
5, 6, 7
nCK
CL = 10
Rev. 1.0 / Jul. 2012
1.5
<1.875
Reserved
1.5
<1.875
48
DDR3-1600 Speed Bins
For specific Notes See "Speed Bin Table Notes" on page 51.
Speed Bin
DDR3-1600K
CL - nRCD - nRP
Parameter
Symbol
Unit
11-11-11
min
max
Note
Internal read
command to first data
tAA
13.75
(13.125)5,10
20
ns
ACT to internal read or
write delay time
tRCD
13.75
(13.125)5,10
—
ns
PRE command period
tRP
13.75
(13.125)5,10
—
ns
ACT to ACT or REF
command period
tRC
48.75
(48.125)5,10
—
ns
ACT to PRE command
period
tRAS
35
9 * tREFI
ns
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
2.5
3.3
ns
1,2,3,8
Reserved
ns
1,2,3,4,8
Reserved
ns
4
ns
4
CWL = 5
CL = 6
CWL = 6
CWL = 7
CWL = 5
CL = 7
CWL = 6
tCK(AVG)
CWL = 7
CWL = 5, 6
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
tCK(AVG)
CWL = 7
tCK(AVG)
CWL = 8
CWL = 5
CL = 8
CWL = 6
CWL = 7
CWL = 8
CL = 9
tCK(AVG)
CWL = 5, 6 tCK(AVG)
tCK(AVG)
CL = 10 CWL = 7
tCK(AVG)
CWL = 8
CWL = 5, 6,7 tCK(AVG)
CL = 11
tCK(AVG)
CWL = 8
Reserved
1.875
< 2.5
(Optional)5,10
Reserved
ns
1,2,3,4,8
ns
1,2,3,4,8
Reserved
ns
4
Reserved
ns
4
1.875
< 2.5
ns
1,2,3,8
ns
1,2,3,4,8
Reserved
ns
1,2,3,4
Reserved
ns
4
ns
1,2,3,4,8
ns
1,2,3,4
Reserved
1.5
<1.875
5,10
(Optional)
Reserved
CWL = 8
Reserved
ns
4
ns
1,2,3,8
Reserved
ns
1,2,3,4
Reserved
ns
4
ns
1,2,3
1.5
<1.875
1.25
<1.5
Supported CL Settings
5, 6, 7, 8, 9, 10, 11
Supported CWL Settings
5, 6, 7, 8
Rev. 1.0 / Jul. 2012
nCK
nCK
49
DDR3-1866 Speed Bins
For specific Notes See "Speed Bin Table Notes" on page 51.
Speed Bin
DDR3-1866M
CL - nRCD - nRP
Parameter
Symbol
Internal read command
to first data
tAA
ACT to internal read or
write delay time
tRCD
PRE command period
tRP
ACT to PRE command
period
tRAS
ACT to ACT or PRE
command period
tRC
tCK(AVG)
tCK(AVG)
CWL = 6
CWL = 7,8,9 tCK(AVG)
tCK(AVG)
CWL = 5
tCK(AVG)
CWL = 6
CWL = 7,8,9 tCK(AVG)
tCK(AVG)
CWL = 5
tCK(AVG)
CWL = 6
tCK(AVG)
CWL = 7
tCK(AVG)
CWL = 8,9
tCK(AVG)
CWL = 5, 6
tCK(AVG)
CWL = 7
tCK(AVG)
CWL = 8
tCK(AVG)
CWL = 9
tCK(AVG)
CWL = 5, 6
tCK(AVG)
CWL = 7
tCK(AVG)
CWL = 8
CWL = 5,6,7 tCK(AVG)
tCK(AVG)
CWL = 8
tCK(AVG)
CWL = 9
CWL = 5,6,7,8 tCK(AVG)
tCK(AVG)
CWL = 9
CWL = 5,6,7,8 tCK(AVG)
tCK(AVG)
CWL = 9
CWL = 5
CL = 6
CL = 7
CL = 8
CL = 9
CL = 10
CL = 11
CL = 12
CL = 13
Unit
13-13-13
min
13.91
max
20
ns
—
ns
—
ns
9 * tREFI
ns
-
ns
3.3
ns
1,2,3,9
Reserved
ns
1,2,3,4,9
Reserved
ns
4
(13.125)5,11
13.91
(13.125)5,11
13.91
(13.125)5,11
34
47.91
(47.125)5,11
2.5
Reserved
ns
4
ns
1,2,3,4,9
Reserved
ns
4
Reserved
ns
4
1.875
< 2.5
1.875
ns
1,2,3,9
Reserved
< 2.5
ns
1,2,3,4,9
Reserved
ns
4
Reserved
ns
4
ns
1,2,3,4,9
Reserved
ns
1,2,3,4,9
Reserved
ns
4
1.5
<1.875
Reserved
ns
4
ns
1,2,3,9
Reserved
ns
1,2,3,4,9
Reserved
ns
4
ns
1,2,3,4,9
ns
1,2,3,4
1.5
<1.875
1.25
<1.5
Reserved
Reserved
ns
4
Reserved
ns
1,2,3,4
Reserved
1.07
<1.25
Supported CL Settings
6, 7, 8, 9, 10, 11, 13
Supported CWL Settings
5, 6, 7, 8, 9
Rev. 1.0 / Jul. 2012
Note
ns
4
ns
1, 2, 3
nCK
nCK
50
Speed Bin Table Notes
Absolute Specification (TOPER; VDDQ = VDD = 1.5V +/- 0.075 V);
1. The CL setting and CWL setting result in tCK(AVG).MIN and tCK(AVG).MAX requirements. When making a selection of tCK(AVG), both need to be fulfilled: Requirements from CL setting as well as requirements from CWL setting.
2. tCK(AVG).MIN limits: Since CAS Latency is not purely analog - data and strobe output are synchronized by the DLL - all possible intermediate frequencies may not be guaranteed. An application should
use the next smaller JEDEC standard tCK(AVG) value (3.0, 2.5, 1.875, 1.5, or 1.25 ns) when calculating CL [nCK] = tAA [ns] / tCK(AVG) [ns], rounding up to the next ‘Supported CL’, where tCK(AVG) =
3.0 ns should only be used for CL = 5 calculation.
3. tCK(AVG).MAX limits: Calculate tCK(AVG) = tAA.MAX / CL SELECTED and round the resulting tCK(AVG)
down to the next valid speed bin (i.e. 3.3ns or 2.5ns or 1.875 ns or 1.25 ns). This result is
tCK(AVG).MAX corresponding to CL SELECTED.
4. ‘Reserved’ settings are not allowed. User must program a different value.
5. ‘Optional’ settings allow certain devices in the industry to support this setting, however, it is not a mandatory feature. Refer to DIMM data sheet and/or the DIMM SPD information if and how this setting is
supported.
6. Any DDR3-1066 speed bin also supports functional operation at lower frequencies as shown in the
table which are not subject to Production Tests but verified by Design/Characterization.
7. Any DDR3-1333 speed bin also supports functional operation at lower frequencies as shown in the
table which are not subject to Production Tests but verified by Design/Characterization.
8. Any DDR3-1600 speed bin also supports functional operation at lower frequencies as shown in the
table which are not subject to Production Tests but verified by Design/Characterization.
9. Any DDR3-1866 speed bin also supports functional operation at lower frequencies as shown in the
table which are not subject to Production Tests but verified by Design/Characterization.
10. DDR3 SDRAM devices supporting optional down binning to CL=7 and CL=9, and tAA/tRCD/tRP must
be 13.125 ns or lower. SPD settings must be programmed to match. For example, DDR3-1333H
devices supporting down binning to DDR3-1066F should program 13.125 ns in SPD bytes for tAAmin
(Byte 16), tRCDmin (Byte 18), and tRPmin (Byte 20). DDR3-1600K devices supporting down binning to
DDR3-1333H or DDR3-1600F should program 13.125 ns in SPD bytes for tAAmin (Byte 16), tRCDmin
(Byte 18), and tRPmin (Byte 20). Once tRP (Byte 20) is programmed to 13.125ns, tRCmin (Byte 21,23)
also should be programmed accordingly. For example, 49.125ns (tRASmin + tRPmin = 36 ns + 13.125
ns) for DDR3-1333H and 48.125ns (tRASmin + tRPmin = 35 ns + 13.125 ns) for DDR3-1600K.
11. DDR3 SDRAM devices supporting optional down binning to CL=11, CL=9 and CL=7, tAA/tRCD/tRPmin
must be 13.125ns. SPD setting must be programed to match. For example, DDR3-1866 devices supporting down binning to DDR3-1600 or DDR3-1333 or 1066 should program 13.125ns in SPD bytes for
tAAmin(byte 16), tRCDmin(byte 18) and tRPmin(byte 20) is programmed to 13.125ns, tRCmin(byte
21,23) also should be programmed accordingly. For example, 47.125ns (tRASmin + tRPmin = 34ns +
13.125ns)
Rev. 1.0 / Jul. 2012
51
Environmental Parameters
Symbol
Parameter
Rating
TOPR
Operating temperature
See Note
HOPR
Operating humidity (relative)
10 to 90
TSTG
Storage temperature
HSTG
Storage humidity (without condensation)
PBAR
Barometric Pressure (operating & storage)
Units
Notes
3
%
1
o
C
1
5 to 95
%
1
105 to 69
K Pascal
1, 2
-50 to +100
Note:
1. Stress greater than those listed may cause permanent damage to the device. This is a stress rating only,
and device functional operation at or above the conditions indicated is not implied. Expousure to absolute
maximum rating conditions for extended periods may affect reliablility.
2. Up to 9850 ft.
3. The designer must meet the case temperature specifications for individual module components.
Rev. 1.0 / Jul. 2012
52
IDD and IDDQ Specification Parameters and Test Conditions
IDD and IDDQ Measurement Conditions
In this chapter, IDD and IDDQ measurement conditions such as test load and patterns are defined. Figure
1. shows the setup and test load for IDD and IDDQ measurements.
•
IDD currents (such as IDD0, IDD1, IDD2N, IDD2NT, IDD2P0, IDD2P1, IDD2Q, IDD3N, IDD3P, IDD4R,
IDD4W, IDD5B, IDD6, IDD6ET and IDD7) are measured as time-averaged currents with all VDD balls
of the DDR3 SDRAM under test tied together. Any IDDQ current is not included in IDD currents.
•
IDDQ currents (such as IDDQ2NT and IDDQ4R) are measured as time-averaged currents with all
VDDQ balls of the DDR3 SDRAM under test tied together. Any IDD current is not included in IDDQ currents.
Attention: IDDQ values cannot be directly used to calculate IO power of the DDR3 SDRAM. They can
be used to support correlation of simulated IO power to actual IO power as outlined in Figure 2. In
DRAM module application, IDDQ cannot be measured separately since VDD and VDDQ are using one
merged-power layer in Module PCB.
For IDD and IDDQ measurements, the following definitions apply:
•
”0” and “LOW” is defined as VIN <= VILAC(max).
•
”1” and “HIGH” is defined as VIN >= VIHAC(max).
•
“MID_LEVEL” is defined as inputs are VREF = VDD/2.
•
Timing used for IDD and IDDQ Measurement-Loop Patterns are provided in Table 1.
•
Basic IDD and IDDQ Measurement Conditions are described in Table 2.
•
Detailed IDD and IDDQ Measurement-Loop Patterns are described in Table 3 through Table 10.
•
IDD Measurements are done after properly initializing the DDR3 SDRAM. This includes but is not limited to setting
RON = RZQ/7 (34 Ohm in MR1);
Qoff = 0B (Output Buffer enabled in MR1);
RTT_Nom = RZQ/6 (40 Ohm in MR1);
RTT_Wr = RZQ/2 (120 Ohm in MR2);
TDQS Feature disabled in MR1
•
Attention: The IDD and IDDQ Measurement-Loop Patterns need to be executed at least one time
before actual IDD or IDDQ measurement is started.
•
Define D = {CS, RAS, CAS, WE}:= {HIGH, LOW, LOW, LOW}
•
Define D = {CS, RAS, CAS, WE}:= {HIGH, HIGH, HIGH, HIGH}
Rev. 1.0 / Jul. 2012
53
IDDQ (optional)
IDD
VDD
VDDQ
RESET
CK/CK
DDR3
SDRAM
CKE
CS
RAS, CAS, WE
DQS, DQS
DQ, DM,
TDQS, TDQS
A, BA
ODT
ZQ
VSS
RTT = 25 Ohm
VDDQ/2
VSSQ
Figure 1 - Measurement Setup and Test Load for IDD and IDDQ (optional) Measurements
[Note: DIMM level Output test load condition may be different from above
Application specific
memory channel
environment
IDDQ
Test Load
Channel
IO Power
Simulation
IDDQ
Simulation
IDDQ
Simulation
Correction
Channel IO Power
Number
Figure 2 - Correlation from simulated Channel IO Power to actual Channel IO Power supported
by IDDQ Measurement
Rev. 1.0 / Jul. 2012
54
Table 1 -Timings used for IDD and IDDQ Measurement-Loop Patterns
Symbol
tCK
DDR3-1066
DDR3-1333
DDR3-1600
DDR3-1866
7-7-7
9-9-9
11-11-11
13-13-13
1.875
1.5
1.25
1.25
Unit
ns
CL
7
9
11
11
nCK
nRCD
7
9
11
11
nCK
nRC
27
33
39
39
nCK
nRAS
20
24
28
28
nCK
nRP
7
9
11
11
nCK
1KB page size
20
20
24
24
nCK
2KB page size
27
30
32
32
nCK
1KB page size
4
4
5
5
nCK
nFAW
nRRD
6
5
6
6
nCK
nRFC -512Mb
2KB page size
48
60
72
72
nCK
nRFC-1 Gb
59
74
88
88
nCK
nRFC- 2 Gb
86
107
128
128
nCK
nRFC- 4 Gb
139
174
208
208
nCK
nRFC- 8 Gb
187
234
280
280
nCK
Table 2 -Basic IDD and IDDQ Measurement Conditions
Symbol
Description
Operating One Bank Active-Precharge Current
CKE: High; External clock: On; tCK, nRC, nRAS, CL: see Table 1; BL: 8a); AL: 0; CS: High between ACT and
IDD0
PRE; Command, Address, Bank Address Inputs: partially toggling according to Table 3; Data IO: MID-LEVEL;
DM: stable at 0; Bank Activity: Cycling with one bank active at a time: 0,0,1,1,2,2,... (see Table 3); Output Buffer and RTT: Enabled in Mode Registersb); ODT Signal: stable at 0; Pattern Details: see Table 3.
Operating One Bank Active-Precharge Current
CKE: High; External clock: On; tCK, nRC, nRAS, nRCD, CL: see Table 1; BL: 8a); AL: 0; CS: High between ACT,
IDD1
RD and PRE; Command, Address; Bank Address Inputs, Data IO: partially toggling according to Table 4; DM:
stable at 0; Bank Activity: Cycling with on bank active at a time: 0,0,1,1,2,2,... (see Table 4); Output Buffer and
RTT: Enabled in Mode Registersb); ODT Signal: stable at 0; Pattern Details: see Table 4.
Rev. 1.0 / Jul. 2012
55
Symbol
Description
Precharge Standby Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 8a); AL: 0; CS: stable at 1; Command, Address, Bank
IDD2N
Address Inputs: partially toggling according to Table 5; Data IO: MID_LEVEL; DM: stable at 0; Bank Activity: all
banks closed; Output Buffer and RTT: Enabled in Mode Registersb); ODT Signal: stable at 0; Pattern Details:
see Table 5.
Precharge Standby ODT Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 8a); AL: 0; CS: stable at 1; Command, Address, Bank
IDD2NT Address Inputs: partially toggling according to Table 6; Data IO: MID_LEVEL; DM: stable at 0; Bank Activity: all
banks closed; Output Buffer and RTT: Enabled in Mode Registersb); ODT Signal: toggling according to Table 6;
Pattern Details: see Table 6.
Precharge Power-Down Current Slow Exit
IDD2P0
CKE: Low; External clock: On; tCK, CL: see Table 1; BL: 8a); AL: 0; CS: stable at 1; Command, Address, Bank
Address Inputs: stable at 0; Data IO: MID_LEVEL; DM: stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registersb); ODT Signal: stable at 0; Precharge Power Down Mode: Slow Exitc)
Precharge Power-Down Current Fast Exit
IDD2P1
CKE: Low; External clock: On; tCK, CL: see Table 1; BL: 8a); AL: 0; CS: stable at 1; Command, Address, Bank
Address Inputs: stable at 0; Data IO: MID_LEVEL; DM: stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registersb); ODT Signal: stable at 0; Precharge Power Down Mode: Fast Exitc)
Precharge Quiet Standby Current
IDD2Q
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 8a); AL: 0; CS: stable at 1; Command, Address, Bank
Address Inputs: stable at 0; Data IO: MID_LEVEL; DM: stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registersb); ODT Signal: stable at 0
Active Standby Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 8a); AL: 0; CS: stable at 1; Command, Address, Bank
IDD3N
Address Inputs: partially toggling according to Table 5; Data IO: MID_LEVEL; DM: stable at 0; Bank Activity: all
banks open; Output Buffer and RTT: Enabled in Mode Registersb); ODT Signal: stable at 0; Pattern Details: see
Table 5.
Active Power-Down Current
IDD3P
CKE: Low; External clock: On; tCK, CL: see Table 1; BL: 8a); AL: 0; CS: stable at 1; Command, Address, Bank
Address Inputs: stable at 0; Data IO: MID_LEVEL; DM: stable at 0; Bank Activity: all banks open; Output Buffer
and RTT: Enabled in Mode Registersb); ODT Signal: stable at 0
Rev. 1.0 / Jul. 2012
56
Symbol
Description
Operating Burst Read Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 8a); AL: 0; CS: High between RD; Command, Address,
IDD4R
Bank Address Inputs: partially toggling according to Table 7; Data IO: seamless read data burst with different
data between one burst and the next one according to Table 7; DM: stable at 0; Bank Activity: all banks open,
RD commands cycling through banks: 0,0,1,1,2,2,...(see Table 7); Output Buffer and RTT: Enabled in Mode
Registersb); ODT Signal: stable at 0; Pattern Details: see Table 7.
Operating Burst Write Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 8a); AL: 0; CS: High between WR; Command, Address,
IDD4W
Bank Address Inputs: partially toggling according to Table 8; Data IO: seamless read data burst with different
data between one burst and the next one according to Table 8; DM: stable at 0; Bank Activity: all banks open,
WR commands cycling through banks: 0,0,1,1,2,2,...(see Table 8); Output Buffer and RTT: Enabled in Mode
Registersb); ODT Signal: stable at HIGH; Pattern Details: see Table 8.
Burst Refresh Current
CKE: High; External clock: On; tCK, CL, nRFC: see Table 1; BL: 8a); AL: 0; CS: High between REF; Command,
IDD5B
Address, Bank Address Inputs: partially toggling according to Table 9; Data IO: MID_LEVEL; DM: stable at 0;
Bank Activity: REF command every nREF (see Table 9); Output Buffer and RTT: Enabled in Mode Registersb);
ODT Signal: stable at 0; Pattern Details: see Table 9.
Self-Refresh Current: Normal Temperature Range
TCASE: 0 - 85 oC; Auto Self-Refresh (ASR): Disabledd);Self-Refresh Temperature Range (SRT): Normale); CKE:
IDD6
Low; External clock: Off; CK and CK: LOW; CL: see Table 1; BL: 8a); AL: 0; CS, Command, Address, Bank
Address Inputs, Data IO: MID_LEVEL; DM: stable at 0; Bank Activity: Self-Refresh operation; Output Buffer
and RTT: Enabled in Mode Registersb); ODT Signal: MID_LEVEL
Self-Refresh Current: Extended Temperature Range (optional)
TCASE: 0 - 95 oC; Auto Self-Refresh (ASR): Disabledd);Self-Refresh Temperature Range (SRT): Extendede);
IDD6ET
CKE: Low; External clock: Off; CK and CK: LOW; CL: see Table 1; BL: 8a); AL: 0; CS, Command, Address, Bank
Address Inputs, Data IO: MID_LEVEL; DM: stable at 0; Bank Activity: Extended Temperature Self-Refresh
operation; Output Buffer and RTT: Enabled in Mode Registersb); ODT Signal: MID_LEVEL
Rev. 1.0 / Jul. 2012
57
Symbol
Description
Operating Bank Interleave Read Current
CKE: High; External clock: On; tCK, nRC, nRAS, nRCD, NRRD, nFAW, CL: see Table 1; BL: 8a),f); AL: CL-1; CS:
High between ACT and RDA; Command, Address, Bank Address Inputs: partially toggling according to Table
IDD7
10; Data IO: read data burst with different data between one burst and the next one according to Table 10;
DM: stable at 0; Bank Activity: two times interleaved cycling through banks (0, 1,...7) with different addressing, wee Table 10; Output Buffer and RTT: Enabled in Mode Registersb); ODT Signal: stable at 0; Pattern
Details: see Table 10.
a) Burst Length: BL8 fixed by MRS: set MR0 A[1,0]=00B
b) Output Buffer Enable: set MR1 A[12] = 0B; set MR1 A[5,1] = 01B; RTT_Nom enable: set MR1 A[9,6,2]
= 011B; RTT_Wr enable: set MR2 A[10,9] = 10B
c) Precharge Power Down Mode: set MR0 A12=0B for Slow Exit or MR0 A12 = 1B for Fast Exit
d) Auto Self-Refresh (ASR): set MR2 A6 = 0B to disable or 1B to enable feature
e) Self-Refresh Temperature Range (SRT): set MR2 A7 = 0B for normal or 1B for extended temperature
range
f) Read Burst Type: Nibble Sequential, set MR0 A[3] = 0B
Rev. 1.0 / Jul. 2012
58
Command
CS
RAS
CAS
WE
ODT
BA[2:0]
A[15:11]
A[10]
A[9:7]
A[6:3]
A[2:0]
0
ACT
0
0
1
1
0
0
00
0
0
0
0
-
1,2
D, D
1
0
0
0
0
0
00
0
0
0
0
-
D, D
1
1
1
1
0
0
00
0
0
0
0
-
0
0
0
-
Cycle
Number
Datab)
Sub-Loop
CKE
CK, CK
Table 3 - IDD0 Measurement-Loop Patterna)
0
3,4
...
nRAS
Static High
toggling
...
repeat pattern 1...4 until nRAS - 1, truncate if necessary
PRE
0
0
1
0
0
0
00
0
repeat pattern 1...4 until nRC - 1, truncate if necessary
1*nRC+0
ACT
0
0
1
1
0
0
00
0
0
F
0
-
1*nRC+1, 2
D, D
1
0
0
0
0
0
00
0
0
F
0
-
D, D
1
1
1
1
0
0
00
0
0
F
0
-
0
-
1*nRC+3, 4
...
1*nRC+nRAS
repeat pattern 1...4 until 1*nRC + nRAS - 1, truncate if necessary
PRE
0
0
1
0
0
0
00
0
0
...
repeat pattern 1...4 until 2*nRC - 1, truncate if necessary
1
2*nRC
repeat Sub-Loop 0, use BA[2:0] = 1 instead
2
4*nRC
repeat Sub-Loop 0, use BA[2:0] = 2 instead
3
6*nRC
repeat Sub-Loop 0, use BA[2:0] = 3 instead
4
8*nRC
repeat Sub-Loop 0, use BA[2:0] = 4 instead
5
10*nRC
repeat Sub-Loop 0, use BA[2:0] = 5 instead
6
12*nRC
repeat Sub-Loop 0, use BA[2:0] = 6 instead
7
14*nRC
repeat Sub-Loop 0, use BA[2:0] = 7 instead
F
a) DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
b) DQ signals are MID-LEVEL.
Rev. 1.0 / Jul. 2012
59
Command
CS
RAS
CAS
WE
ODT
BA[2:0]
A[15:11]
A[10]
A[9:7]
A[6:3]
A[2:0]
0
ACT
0
0
1
1
0
0
00
0
0
0
0
-
1,2
D, D
1
0
0
0
0
0
00
0
0
0
0
-
D, D
1
1
1
1
0
0
00
0
0
0
0
-
0
0
00000000
0
0
-
Cycle
Number
Datab)
Sub-Loop
CKE
CK, CK
Table 4 - IDD1 Measurement-Loop Patterna)
0
3,4
...
nRCD
...
nRAS
Static High
toggling
...
repeat pattern 1...4 until nRCD - 1, truncate if necessary
RD
0
1
0
1
0
0
00
0
0
repeat pattern 1...4 until nRAS - 1, truncate if necessary
PRE
0
0
1
0
0
0
00
0
0
repeat pattern 1...4 until nRC - 1, truncate if necessary
1*nRC+0
ACT
0
0
1
1
0
0
00
0
0
F
0
-
1*nRC+1,2
D, D
1
0
0
0
0
0
00
0
0
F
0
-
D, D
1
1
1
1
0
0
00
0
0
F
0
-
1*nRC+3,4
...
1*nRC+nRCD
...
1*nRC+nRAS
repeat pattern nRC + 1,...4 until nRC + nRCE - 1, truncate if necessary
RD
0
1
0
1
0
0
00
0
0
F
0
00110011
repeat pattern nRC + 1,...4 until nRC + nRAS - 1, truncate if necessary
PRE
0
0
1
0
0
0
00
0
0
F
...
repeat pattern nRC + 1,...4 until *2 nRC - 1, truncate if necessary
1
2*nRC
repeat Sub-Loop 0, use BA[2:0] = 1 instead
2
4*nRC
repeat Sub-Loop 0, use BA[2:0] = 2 instead
3
6*nRC
repeat Sub-Loop 0, use BA[2:0] = 3 instead
4
8*nRC
repeat Sub-Loop 0, use BA[2:0] = 4 instead
5
10*nRC
repeat Sub-Loop 0, use BA[2:0] = 5 instead
6
12*nRC
repeat Sub-Loop 0, use BA[2:0] = 6 instead
7
14*nRC
repeat Sub-Loop 0, use BA[2:0] = 7 instead
0
-
a) DM must be driven LOW all the time. DQS, DQS are used according to RD Commands, otherwise MIDLEVEL.
b) Burst Sequence driven on each DQ signal by Read Command. Outside burst operation, DQ signals are
MID_LEVEL.
Rev. 1.0 / Jul. 2012
60
Static High
CS
RAS
CAS
WE
ODT
BA[2:0]
A[15:11]
A[10]
A[9:7]
A[6:3]
A[2:0]
0
D
1
0
0
0
0
0
0
0
0
0
0
-
1
D
1
0
0
0
0
0
0
0
0
0
0
-
2
D
1
1
1
1
0
0
0
0
0
F
0
-
3
D
1
1
1
1
0
0
0
0
0
F
0
-
Cycle
Number
Command
0
toggling
Datab)
Sub-Loop
CKE
CK, CK
Table 5 - IDD2N and IDD3N Measurement-Loop Patterna)
1
4-7
repeat Sub-Loop 0, use BA[2:0] = 1 instead
2
8-11
repeat Sub-Loop 0, use BA[2:0] = 2 instead
3
12-15
repeat Sub-Loop 0, use BA[2:0] = 3 instead
4
16-19
repeat Sub-Loop 0, use BA[2:0] = 4 instead
5
20-23
repeat Sub-Loop 0, use BA[2:0] = 5 instead
6
24-17
repeat Sub-Loop 0, use BA[2:0] = 6 instead
7
28-31
repeat Sub-Loop 0, use BA[2:0] = 7 instead
a) DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
b) DQ signals are MID-LEVEL.
Static High
CS
RAS
CAS
WE
ODT
BA[2:0]
A[15:11]
A[10]
A[9:7]
A[6:3]
A[2:0]
0
D
1
0
0
0
0
0
0
0
0
0
0
-
1
D
1
0
0
0
0
0
0
0
0
0
0
-
2
D
1
1
1
1
0
0
0
0
0
F
0
-
3
D
1
1
1
1
0
0
0
0
0
F
0
-
Cycle
Number
Command
0
toggling
Datab)
Sub-Loop
CKE
CK, CK
Table 6 - IDD2NT and IDDQ2NT Measurement-Loop Patterna)
1
4-7
repeat Sub-Loop 0, but ODT = 0 and BA[2:0] = 1
2
8-11
repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 2
3
12-15
repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 3
4
16-19
repeat Sub-Loop 0, but ODT = 0 and BA[2:0] = 4
5
20-23
repeat Sub-Loop 0, but ODT = 0 and BA[2:0] = 5
6
24-17
repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 6
7
28-31
repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 7
a) DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
b) DQ signals are MID-LEVEL.
Rev. 1.0 / Jul. 2012
61
CS
RAS
CAS
WE
ODT
BA[2:0]
A[15:11]
A[10]
A[9:7]
A[6:3]
A[2:0]
0
RD
0
1
0
1
0
0
00
0
0
0
0
00000000
1
D
1
0
0
0
0
0
00
0
0
0
0
-
2,3
D,D
1
1
1
1
0
0
00
0
0
0
0
-
4
RD
0
1
0
1
0
0
00
0
0
F
0
00110011
5
D
1
0
0
0
0
0
00
0
0
F
0
-
D,D
1
1
1
1
0
0
00
0
0
F
0
-
Cycle
Number
Command
Static High
0
toggling
Datab)
Sub-Loop
CKE
CK, CK
Table 7 - IDD4R and IDDQ4R Measurement-Loop Patterna)
6,7
1
8-15
repeat Sub-Loop 0, but BA[2:0] = 1
2
16-23
repeat Sub-Loop 0, but BA[2:0] = 2
3
24-31
repeat Sub-Loop 0, but BA[2:0] = 3
4
32-39
repeat Sub-Loop 0, but BA[2:0] = 4
5
40-47
repeat Sub-Loop 0, but BA[2:0] = 5
6
48-55
repeat Sub-Loop 0, but BA[2:0] = 6
7
56-63
repeat Sub-Loop 0, but BA[2:0] = 7
a) DM must be driven LOW all the time. DQS, DQS are used according to RD Commands, otherwise MID-LEVEL.
b) Burst Sequence driven on each DQ signal by Read Command. Outside burst operation, DQ signals are MID-LEVEL.
0,
0,
0,
0,
0,
0,
0,
1
1
1
1
1
1
=
=
=
=
=
=
=
A[2:0]
ODT
0
0
1
0
0
1
BA[2:0]
BA[2:0]
BA[2:0]
BA[2:0]
BA[2:0]
BA[2:0]
BA[2:0]
A[6:3]
0
0
1
0
0
1
but
but
but
but
but
but
but
WE
CAS
RAS
CS
0
1
1
0
1
1
0
1
1
0
1
1
Sub-Loop
Sub-Loop
Sub-Loop
Sub-Loop
Sub-Loop
Sub-Loop
Sub-Loop
A[9:7]
WR
D
D,D
WR
D
D,D
repeat
repeat
repeat
repeat
repeat
repeat
repeat
A[10]
1
2
3
4
5
6
7
1
2,3
4
5
6,7
8-15
16-23
24-31
32-39
40-47
48-55
56-63
A[15:11]
0
BA[2:0]
0
Command
Cycle
Number
Sub-Loop
CKE
Static High
toggling
CK, CK
Table 8 - IDD4W Measurement-Loop Patterna)
Datab)
0
0
0
0
0
0
00
00
00
00
00
00
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
F
F
F
0
0
0
0
0
0
00000000
00110011
-
1
2
3
4
5
6
7
a) DM must be driven LOW all the time. DQS, DQS are used according to WR Commands, otherwise MID-LEVEL.
b) Burst Sequence driven on each DQ signal by Write Command. Outside burst operation, DQ signals are MID-LEVEL.
Rev. 1.0 / Jul. 2012
62
Command
CS
RAS
CAS
WE
ODT
BA[2:0]
A[15:11]
A[10]
A[9:7]
A[6:3]
A[2:0]
0
0
REF
0
0
0
1
0
0
0
0
0
0
0
-
1
1.2
D, D
1
0
0
0
0
0
00
0
0
0
0
-
D, D
1
1
1
1
0
0
00
0
0
F
0
-
Cycle
Number
Datab)
Sub-Loop
CKE
CK, CK
Table 9 - IDD5B Measurement-Loop Patterna)
Static High
toggling
3,4
2
5...8
repeat cycles 1...4, but BA[2:0] = 1
9...12
repeat cycles 1...4, but BA[2:0] = 2
13...16
repeat cycles 1...4, but BA[2:0] = 3
17...20
repeat cycles 1...4, but BA[2:0] = 4
21...24
repeat cycles 1...4, but BA[2:0] = 5
25...28
repeat cycles 1...4, but BA[2:0] = 6
29...32
repeat cycles 1...4, but BA[2:0] = 7
33...nRFC-1
repeat Sub-Loop 1, until nRFC - 1. Truncate, if necessary.
a) DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
b) DQ signals are MID-LEVEL.
Rev. 1.0 / Jul. 2012
63
Table 10 - IDD7 Measurement-Loop Patterna)
2
3
4
Static High
5
6
7
8
9
10
4*nRRD
nFAW
nFAW+nRRD
nFAW+2*nRRD
nFAW+3*nRRD
nFAW+4*nRRD
2*nFAW+0
2*nFAW+1
2&nFAW+2
11
2*nFAW+nRRD
2*nFAW+nRRD+1
2&nFAW+nRRD+2
12
13
2*nFAW+2*nRRD
2*nFAW+3*nRRD
14
2*nFAW+4*nRRD
15
16
17
18
3*nFAW
3*nFAW+nRRD
3*nFAW+2*nRRD
3*nFAW+3*nRRD
19
3*nFAW+4*nRRD
00110011
-
0
-
0
-
0
0
0
00110011
-
0
0
0
00000000
-
0
-
0
-
A[10]
0
0
0
ODT
00000000
-
WE
0
0
0
CAS
ACT
0
0
1
1
0
0
00
0
0
0
RDA
0
1
0
1
0
0
00
1
0
0
D
1
0
0
0
0
0
00
0
0
0
repeat above D Command until nRRD - 1
ACT
0
0
1
1
0
1
00
0
0
F
RDA
0
1
0
1
0
1
00
1
0
F
D
1
0
0
0
0
1
00
0
0
F
repeat above D Command until 2* nRRD - 1
repeat Sub-Loop 0, but BA[2:0] = 2
repeat Sub-Loop 1, but BA[2:0] = 3
D
1
0
0
0
0
3
00
0
0
F
Assert and repeat above D Command until nFAW - 1, if necessary
repeat Sub-Loop 0, but BA[2:0] = 4
repeat Sub-Loop 1, but BA[2:0] = 5
repeat Sub-Loop 0, but BA[2:0] = 6
repeat Sub-Loop 1, but BA[2:0] = 7
D
1
0
0
0
0
7
00
0
0
F
Assert and repeat above D Command until 2* nFAW - 1, if necessary
ACT
0
0
1
1
0
0
00
0
0
F
RDA
0
1
0
1
0
0
00
1
0
F
D
1
0
0
0
0
0
00
0
0
F
Repeat above D Command until 2* nFAW + nRRD - 1
ACT
0
0
1
1
0
1
00
0
0
0
RDA
0
1
0
1
0
1
00
1
0
0
D
1
0
0
0
0
1
00
0
0
0
Repeat above D Command until 2* nFAW + 2* nRRD - 1
repeat Sub-Loop 10, but BA[2:0] = 2
repeat Sub-Loop 11, but BA[2:0] = 3
D
1
0
0
0
0
3
00
0
0
0
Assert and repeat above D Command until 3* nFAW - 1, if necessary
repeat Sub-Loop 10, but BA[2:0] = 4
repeat Sub-Loop 11, but BA[2:0] = 5
repeat Sub-Loop 10, but BA[2:0] = 6
repeat Sub-Loop 11, but BA[2:0] = 7
D
1
0
0
0
0
7
00
0
0
0
Assert and repeat above D Command until 4* nFAW - 1, if necessary
RAS
Datab)
CS
A[9:7]
A[15:11]
BA[2:0]
Command
A[2:0]
1
0
1
2
...
nRRD
nRRD+1
nRRD+2
...
2*nRRD
3*nRRD
A[6:3]
0
toggling
Cycle
Number
Sub-Loop
CKE
CK, CK
ATTENTION! Sub-Loops 10-19 have inverse A[6:3] Pattern and Data Pattern than Sub-Loops 0-9
a) DM must be driven LOW all the time. DQS, DQS are used according to RD Commands, otherwise MID-LEVEL.
b) Burst Sequence driven on each DQ signal by Read Command. Outside burst operation, DQ signals are MID-LEVEL.
Rev. 1.0 / Jul. 2012
64
IDD Specifications (Tcase: 0 to 95oC)
* Module IDD values in the datasheet are only a calculation based on the component IDD spec and register power.
The actual measurements may vary according to DQ loading cap.
2GB, 256M x 72 R-DIMM: HMT325R7CFR8C
Symbol
IDD0
IDD1
IDD2N
IDD2NT
IDD2P0
IDD2P1
IDD2Q
IDD3N
IDD3P
IDD4R
IDD4W
IDD5B
IDD6
IDD6ET
IDD7
DDR3 1333
1124
1214
944
989
336
363
971
1007
363
1574
1529
1799
336
354
2384
DDR3 1600
1169
1259
989
1034
336
363
971
1034
384
1709
1619
1844
336
354
2429
DDR3 1866
1169
1304
989
1034
336
381
989
1034
390
1889
1844
1844
336
354
2564
Unit
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
note
DDR3 1866
1439
1574
1214
1304
444
534
1214
1304
552
2159
2114
2114
444
480
2834
Unit
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
note
4GB, 512M x 72 R-DIMM: HMT351R7CFR8C
Symbol
IDD0
IDD1
IDD2N
IDD2NT
IDD2P0
IDD2P1
IDD2Q
IDD3N
IDD3P
IDD4R
IDD4W
IDD5B
IDD6
IDD6ET
IDD7
Rev. 1.0 / Jul. 2012
DDR3 1333
1304
1394
1124
1214
444
498
1178
1250
498
1754
1709
1979
444
480
2564
DDR3 1600
1439
1529
1214
1304
444
498
1178
1304
534
1979
1889
2114
444
480
2699
65
4GB, 512M x 72 R-DIMM: HMT351R7CFR4C
Symbol
IDD0
IDD1
IDD2N
IDD2NT
IDD2P0
IDD2P1
DDR3 1333
1484
1664
1124
1214
444
498
DDR3 1600
1574
1754
1214
1304
444
498
DDR3 1866
1574
1844
1214
1304
444
534
Unit
mA
mA
mA
mA
mA
mA
IDD2Q
IDD3N
IDD3P
IDD4R
IDD4W
IDD5B
IDD6
IDD6ET
IDD7
1178
1250
498
2384
2294
2834
444
480
4004
1178
1304
534
2654
2474
2924
444
480
4094
1214
1304
552
3014
2924
2924
444
480
4364
mA
mA
mA
mA
mA
mA
mA
mA
mA
DDR3 1600
1979
2069
1664
1844
660
768
1592
1844
840
2519
2429
2654
660
732
3239
Unit
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
note
8GB, 1G x 72 R-DIMM: HMT31GR7CFR8C
Symbol
IDD0
IDD1
IDD2N
IDD2NT
IDD2P0
IDD2P1
IDD2Q
IDD3N
IDD3P
IDD4R
IDD4W
IDD5B
IDD6
IDD6ET
IDD7
Rev. 1.0 / Jul. 2012
DDR3 1066
1664
1754
1484
1664
660
768
1484
1664
768
1979
1979
2294
660
732
2609
DDR3 1333
1664
1754
1484
1664
660
768
1592
1736
768
2114
2069
2339
660
732
2924
note
66
8GB, 1G x 72 R-DIMM: HMT31GR7CFR4C
Symbol
IDD0
IDD1
IDD2N
IDD2NT
IDD2P0
IDD2P1
DDR3 1333
1844
2024
1484
1664
660
768
DDR3 1600
2114
2294
1664
1844
660
768
DDR3 1866
2114
2384
1664
1844
660
840
Unit
mA
mA
mA
mA
mA
mA
IDD2Q
IDD3N
IDD3P
IDD4R
IDD4W
IDD5B
IDD6
IDD6ET
IDD7
1592
1736
768
2744
2654
3194
660
732
4364
1592
1844
840
3194
3014
3464
660
732
4634
1664
1844
879
3554
3464
3464
660
732
4904
mA
mA
mA
mA
mA
mA
mA
mA
mA
DDR3 1600
3194
3374
2564
2924
1092
1308
2420
2924
1452
4274
4094
4544
1092
1236
5714
Unit
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
note
16GB, 2G x 72 R-DIMM: HMT42GR7CMR4C
Symbol
IDD0
IDD1
IDD2N
IDD2NT
IDD2P0
IDD2P1
IDD2Q
IDD3N
IDD3P
IDD4R
IDD4W
IDD5B
IDD6
IDD6ET
IDD7
Rev. 1.0 / Jul. 2012
DDR3 1066
2564
2744
2204
2564
1092
1308
2204
2564
1308
3194
3194
3824
1092
1236
4454
DDR3 1333
2564
2744
2204
2564
1092
1308
2420
2708
1308
3464
3374
3914
1092
1236
5084
note
67
Module Dimensions
256Mx72 - HMT325R7CFR8C
Front
133.35
128.95
Detail A
Detail B
1
Detail C
120
1
2X3.00±0.10
5.175
47.00
30.00
Registering
Clock Driver
4X3.00±0.10
9.50
17.30
SPD/TS
2.10±0.15
71.00
5.0
Back
121
240
1
2x R0.75 Max
Side
3.43mm max
0.80± 0.05
3.80
0.35
2.50±0.20
2.50
2.50±0.20
1.20± 0.15
3± 0.1
Detail of Contacts C
Detail of Contacts B
0.3 ±0.15
Detail of Contacts A
0.3~0.1
1.00
1.50 ±0.10
5.00
1.27±010mm
max
Note:
1.  0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.0 / Jul. 2012
68
512Mx72 - HMT351R7CFR8C
Front
133.35
128.95
SPD/TS
2.10±0.15
Detail C
Detail B
1
120
1
2X3.00±0.10
5.175
47.00
30.00
4X3.00±0.10
9.50
17.30
23.30
Registering
Clock Driver
Detail A
71.00
5.0
Back
121
240
1
2x R0.75 Max
Side
3.43mm max
0.80± 0.05
2.50±0.20
3.80
2.50
2.50±0.20
0.35
3± 0.1
Detail of Contacts C
Detail of Contacts B
1.20± 0.15
0.3 ±0.15
Detail of Contacts A
0.3+0.1
1.00
1.50 ±0.10
5.00
1.27±010mm
max
Note:
1.  0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.0 / Jul. 2012
69
512Mx72 - HMT351R7CFR4C
Front
133.35
128.95
SPD/TS
2.10±0.15
Detail C
Detail B
1
120
1
2X3.00±0.10
5.175
47.00
30.00
4X3.00±0.10
9.50
17.30
23.30
Registering
Clock Driver
Detail A
71.00
5.0
Back
121
240
1
2x R0.75 Max
Side
3.43mm max
0.80± 0.05
2.50±0.20
3.80
2.50
2.50±0.20
0.35
3± 0.1
Detail of Contacts C
Detail of Contacts B
1.20± 0.15
0.3 ±0.15
Detail of Contacts A
0.3+0.1
1.00
1.50 ±0.10
5.00
1.27±010mm
max
Note:
1.  0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.0 / Jul. 2012
70
1Gx72 - HMT31GR7CFR8C
Front
133.35
Detail B
128.95
SPD/TS
2.10±0.15
1
120
1
2X3.00±0.10
47.00
Detail C
5.175
9.50
17.30
23.30
Registering
Clock Driver
4X3.00±0.10
30.00
Detail A
71.00
5.0 Detail D
Back
121
240
1
2x R0.75 Max
Side
Detail of Contacts A
Detail of Contacts D
Detail of Contacts C
Detail of Contacts B
1.20± 0.15
3.46mm max
0.80± 0.05
2.50
14.90
2.50±0.20
0.3 ±0.15
0.35
2.50±0.20
13.60
3± 0.1
3.80
0.4
0.3~0.1
1.00
1.50 ±0.10
5.00
1.27±010mm
max
Note:
1.  0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.0 / Jul. 2012
71
1Gx72 - HMT31GR7CFR8C - Heat Spreader
Front
133.75
133.35
127
42.7
2.786
8
36.7
22.00
30.20
6.3
2.15
7.74
14.214
Registering
Clock Driver
3.69
5.39
10
20.9
6.35
120
1
7.36
33.4
33.4
46.46
80.54
119.64
57.2
Back
15.36
Registering
Clock Driver
121
22.00
2.7
240
2x R0.75 Max
Side
7.19mm max
1.27±010mm
max
Note:
1.  0.13 tolerance on all dimensions unless otherwise stated.
2.In order to uninstall FDHS, please contact sales administrator.
Rev. 1.0 / Jul. 2012
Units: millimeters
72
1Gx72 - HMT31GR7CFR4C
Front
133.35
Detail B
128.95
SPD/TS
2.10±0.15
1
120
1
2X3.00±0.10
47.00
Detail C
5.175
9.50
17.30
23.30
Registering
Clock Driver
4X3.00±0.10
30.00
Detail A
71.00
5.0 Detail D
Back
121
240
1
2x R0.75 Max
Side
Detail of Contacts A
Detail of Contacts D
Detail of Contacts C
Detail of Contacts B
1.20± 0.15
3.46mm max
0.80± 0.05
2.50
14.90
2.50±0.20
0.3 ±0.15
0.35
2.50±0.20
13.60
3± 0.1
3.80
0.4
0.3~0.1
1.00
1.50 ±0.10
5.00
1.27±010mm
max
Note:
1.  0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.0 / Jul. 2012
73
1Gx72 - HMT31GR7CFR4C - Heat Spreader
Front
133.75
133.35
127
42.7
2.786
8
36.7
22.00
30.20
6.3
2.15
7.74
14.214
Registering
Clock Driver
3.69
5.39
10
20.9
6.35
120
1
7.36
33.4
33.4
46.46
80.54
119.64
57.2
Back
15.36
Registering
Clock Driver
121
22.00
2.7
240
2x R0.75 Max
Side
7.19mm max
1.27±010mm
max
Note:
1.  0.13 tolerance on all dimensions unless otherwise stated.
2.In order to uninstall FDHS, please contact sales administrator.
Rev. 1.0 / Jul. 2012
Units: millimeters
74
2Gx72 - HMT42GR7CMR4C
Front
133.35
Detail B
128.95
SPD/TS
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
Detail A
DDP
1
120
1
2X3.00±0.10
47.00
Detail C
5.175
9.50
17.30
23.30
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
Registering
Clock Driver
4X3.00±0.10
30.00
2.10±0.15
71.00
5.0 Detail D
Back
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
DDP
121
240
1
2x R0.75 Max
Side
Detail of Contacts A
Detail of Contacts D
Detail of Contacts C
Detail of Contacts B
1.20± 0.15
3.46mm max
0.80± 0.05
2.50
14.90
2.50±0.20
0.3 ±0.15
0.35
2.50±0.20
13.60
3± 0.1
3.80
0.4
0.3~0.1
1.00
1.50 ±0.10
5.00
1.27±010mm
max
Note:
1.  0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.0 / Jul. 2012
75
2Gx72 - HMT42GR7CMR4C - Heat Spreader
Front
133.75
133.35
127
42.7
2.786
8
36.7
22.00
30.20
6.3
2.15
7.74
14.214
Registering
Clock Driver
3.69
5.39
10
20.9
6.35
120
1
7.36
33.4
33.4
46.46
80.54
119.64
57.2
Back
15.36
Registering
Clock Driver
121
22.00
2.7
240
2x R0.75 Max
Side
7.19mm max
1.27±010mm
max
Note:
1.  0.13 tolerance on all dimensions unless otherwise stated.
2.In order to uninstall FDHS, please contact sales administrator.
Rev. 1.0 / Jul. 2012
Units: millimeters
76