iC-LSB 8-CHANNEL ACTIVE PHOTOSENSOR ARRAY Rev C1, Page 1/7 FEATURES APPLICATIONS ♦ Monolithic array of independent photosensors with excellent matching ♦ Compact photosensor size of 800 µm x 300 µm enabling high-quality encoder scanning at reduced system dimensions ♦ Narrow track pitch of 0.42 mm cuts down illumination efforts ♦ Enhanced EMI immunity due to on-chip pre-amplification ♦ Dark current compensation permits high temperature operation ♦ Open-collector outputs as highside current source ♦ Simple gain setting and current-to-voltage conversion by external load resistors ♦ Single supply operation from 4 V to 5.5 V ♦ Low power consumption ♦ Space saving, RoHS compliant optoQFN and optoBGA packages ♦ Options: extended temperature range of -40 to 125 °C, customized COB modules, reticles and code discs ♦ Optical position encoding from analog sine/cosine signals ♦ Incremental encoders with index signal PACKAGES 14-pin optoBGA 6.2 mm x 5.2 mm BLOCK DIAGRAM Copyright © 2004, 2010 iC-Haus http://www.ichaus.com iC-LSB 8-CHANNEL ACTIVE PHOTOSENSOR ARRAY Rev C1, Page 2/7 DESCRIPTION The iC-LSB sensor array, coming with 8 independent channels, is a general purpose optoelectronic scanner made to suit a variety of encoding applications, such as rotary and linear encoders used for motion control, robotics, power tools etc. The sensor array features monolithically integrated photosensors with active areas of 800 µm x 300 µm each in combination with fast on-chip photocurrent amplifiers, enabling an analog output at reasonable signal strength to the circuit board. avoids a ground referenced signal and permits the subsequent electronics to adjust the gain. In its simplest form this is done by load resistors, for instance. The spectral sensitivity range includes visible to near infrared light, with the maximum sensitivity being close to a wavelength of 700 nm. Output currents of up to 50 µA are supplied under low light conditions, for instance when illuminated at only 3 µW/mm2 by an 850 nm LED. The photocurrent gain is 46 dB typically. The highside current source output construction PACKAGES PAD LAYOUT Chip size 2.80 mm x 1.96 mm PAD FUNCTIONS No. Name Function 1 2 3 4 5 6 7 8 9 10 VCC A1 B1 C1 D1 D2 C2 B2 A2 GND +4...5.5 V Supply Voltage Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Ground iC-LSB 8-CHANNEL ACTIVE PHOTOSENSOR ARRAY Rev C1, Page 3/7 PIN CONFIGURATION oBGA LS2C (6.2 mm x 5.2 mm) PIN FUNCTIONS No. Name Function 1 2 3 4 5 6...9 10 11 12 13 14 VCC A1 B1 C1 D1 n.c. D2 C2 B2 A2 GND +4...5.5 V Supply Voltage Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Highside Current Source Output Ground Pin numbers marked n.c. are not in use. For dimensional specifications refer to the relevant package data sheets, available separately. IC top markings, such as <LOT CODE>, indicate the orientation of the device. iC-LSB 8-CHANNEL ACTIVE PHOTOSENSOR ARRAY Rev C1, Page 4/7 ABSOLUTE MAXIMUM RATINGS These ratings do not imply operating conditions; functional operation is not guaranteed. Beyond these ratings device damage may occur. Item No. Symbol Parameter Conditions Unit Min. Max. G001 VCC Voltage at VCC -0.3 6 V G002 I(VCC) Current in VCC -20 20 mA G003 V() Pin Voltage, all signal outputs -0.3 VCC+0.3 V G004 I() Pin Current, all signal outputs -20 20 mA G005 Vd() ESD Susceptibility, all pins 2 kV G006 Tj Junction Temperature -40 150 °C G007 Ts Chip Storage Temperature -40 150 °C HBM, 100 pF discharged through 1.5 kΩ THERMAL DATA Item No. T01 Symbol Parameter Conditions Unit Min. Ta Operating Ambient Temperature Range package oBGA LS2C Ts Tpk Storage Temperature Range package oBGA LS2C Soldering Peak Temperature package oBGA LS2C Typ. Max. -20 90 °C -30 110 °C 245 230 °C °C (extended temperature range on request) T02 T03 tpk < 20 s, convection reflow tpk < 20 s, vapor phase soldering TOL (time on label) 8 h; Please refer to customer information file No. 7 for details. All voltages are referenced to ground unless otherwise stated. All currents flowing into the device pins are positive; all currents flowing out of the device pins are negative. iC-LSB 8-CHANNEL ACTIVE PHOTOSENSOR ARRAY Rev C1, Page 5/7 ELECTRICAL CHARACTERISTICS Operating conditions: VCC = 4...5.5 V, Tj = -40...125 °C, unless otherwise stated Item No. Symbol Parameter Conditions Unit Min. Typ. Max. Total Device 001 002 VCC Permissible Supply Voltage I(VCC) Supply Current in VCC, dark E() = 0 Tj = 27 °C 4 1.0 003 I(VCC) Supply Current in VCC λLED = λpk, E() = 0.1 mW/cm2 Tj = 27 °C 1.5 004 Vc()hi Clamp-Voltage hi at all pins I() = 4 mA 005 Vc()lo Clamp-Voltage lo at all pins I() = -4 mA -1.2 5.5 V 2 mA mA 4 mA mA 11 V -0.3 V 0.2 mW/ cm2 Photosensors 101 E()mxr Permissible Irradiance λLED = λpk 102 103 Aph() Radiant Sensitive Area 0.8 mm x 0.3 mm per sensor λar Spectral Application Range Se(λar) = 0.25 x S(λ)max see Figure 1 104 λpk Peak Sensitivity Wavelength see Figure 1 680 nm 105 S(λ) Spectral Sensitivity λLED = λpk 0.45 A/W mm2 0.24 400 950 nm Photocurrent Amplifiers 201 Iph() Permissible Photocurrent Operating Range 202 η()r 203 per sensor 0 200 nA Photo Sensitivity λLED = 740 nm (light-to-voltage conversion ratio) 60 120 A/W CR() Photocurrent Gain 150 200 204 fc()hi Cut-off Frequency (-3 dB) 150 200 205 ∆Iout()m Channel Matching deviation from mean value 206 ∆Iout()m Channel Cross Talk only one photosensor illuminated at the same time CR() = Iout() / Iph() -15 250 kHz +15 0 % % Current Source Outputs 301 Vout() Permissible Output Voltage (Operating Range) 302 Iout() Permissible Output Current Vout() = 1 V ... VCC - 1.5 V VCC = 4.5...5.5 V, Vout() = 1 V ... VCC - 2 V 303 tr(), tf() Output Current Rise/Fall Time Iph: 0 → 100 nA, 1T settling (63%); Vout() = constant CL = 30 pF, RL() = 10 kΩ 304 Iout()0 1 Output Dark Current Figure 1: Relative spectral response VCC 1.5 -50 -200 µA µA 0.7 0.8 -0.6 V µs µs +0.6 Figure 2: Typical directional characteristics µA iC-LSB 8-CHANNEL ACTIVE PHOTOSENSOR ARRAY Rev C1, Page 6/7 APPLICATION CIRCUITS Figure 3: Optical encoder application example. Here, the sine-to-digital converter iC-NV is employed to output spike-free encoder quadrature signals featuring a minimum transition distance. iC-Haus expressly reserves the right to change its products and/or specifications. An Infoletter gives details as to any amendments and additions made to the relevant current specifications on our internet website www.ichaus.de/infoletter; this letter is generated automatically and shall be sent to registered users by email. Copying – even as an excerpt – is only permitted with iC-Haus approval in writing and precise reference to source. iC-Haus does not warrant the accuracy, completeness or timeliness of the specification on this site and does not assume liability for any errors or omissions in the materials. The data specified is intended solely for the purpose of product description. No representations or warranties, either express or implied, of merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to information/specification or the products to which information refers and no guarantee with respect to compliance to the intended use is given. In particular, this also applies to the stated possible applications or areas of applications of the product. iC-Haus conveys no patent, copyright, mask work right or other trade mark right to this product. iC-Haus assumes no liability for any patent and/or other trade mark rights of a third party resulting from processing or handling of the product and/or any other use of the product. As a general rule our developments, IPs, principle circuitry and range of Integrated Circuits are suitable and specifically designed for appropriate use in technical applications, such as in devices, systems and any kind of technical equipment, in so far as they do not infringe existing patent rights. In principle the range of use is limitless in a technical sense and refers to the products listed in the inventory of goods compiled for the 2008 and following export trade statistics issued annually by the Bureau of Statistics in Wiesbaden, for example, or to any product in the product catalogue published for the 2007 and following exhibitions in Hanover (Hannover-Messe). We understand suitable application of our published designs to be state-of-the-art technology which can no longer be classed as inventive under the stipulations of patent law. Our explicit application notes are to be treated only as mere examples of the many possible and extremely advantageous uses our products can be put to. iC-LSB 8-CHANNEL ACTIVE PHOTOSENSOR ARRAY Rev C1, Page 7/7 ORDERING INFORMATION Type Package iC-LSB - Options Order Designation iC-LSB chip 14-pin optoBGA 6.2 mm x 5.2 mm glass lid iC-LSB oBGA LS2C 14-pin optoBGA 6.2 mm x 5.2 mm on-chip reticle iC-LSB oBGA LS2C-LSBxR For technical support, information about prices and terms of delivery please contact: iC-Haus GmbH Am Kuemmerling 18 D-55294 Bodenheim GERMANY Tel.: +49 (61 35) 92 92-0 Fax: +49 (61 35) 92 92-192 Web: http://www.ichaus.com E-Mail: [email protected] Appointed local distributors: http://www.ichaus.com/sales_partners