IKSEMICON IL339_11

TECHNI CAL DATA
Quad Single Supply Comparator
The IL339 consists of four independent precision voltage
comparators with an offset voltage specification as low as 2.0 mV
max for four comparators which were designed specifically to
operate from a single power supply over a wide range of voltages.
Application areas include limit comparators, simple analog to
digital converters; pulse, squarewave and time delay generators;
wide range VCO; MOS clock timers; multivibrators and high voltage
digital logic gates.
•
Single or Split Supply Operation
•
Low Input Bias Current
•
Low Input Offset Current
•
Input Common Mode Voltage Range to Gnd
•
Low Output Saturation Voltage
•
TTL and CMOS Compatible
IL339
ORDERING INFORMATION
IL339N Plastic
IL339D SOIC
TA = -40° to 85° C for all
packages.
LOGIC DIAGRAM
PIN ASSIGNMENT
PIN 3 = VCC
PIN 12 = GND
2011, January, ver.01
I L 339
MAXIMUM RATINGS*
Symbol
VCC
Parameter
Value
Unit
36
±18
V
36
V
V
Power Supply Voltages
Single Supply
Split Supplies
VIDR
Input Differential Voltage Range
VICR
Input Common Mode Voltage Range (1)
-0.3 to VCC
ISC
Output Short Circuit to Ground
Continuous
IIN
Input Current, per pin (2)
TJ
Junction Temperature
Plastic Packages
Tstg
TL
Storage Temperature
Lead Temperature, 1mm from Case for 10
Seconds
50
mA
150
°C
-65 to +150
°C
260
°C
PD
Power Dissipation @TA=25°C
1.0
W
Plastic Package
8.0
mW/°C
Derate above 25°C
* Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device.
These are stress ratings only and functional operation of the device at these or any other conditions beyond those
indicated under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Functional operation should be restricted to the Recommended Operating Conditions.
Notes:
1. Split Power Supplies.
2. VIN<-0.3V. This input current will only exist when voltage at any of the input leads is driven negative.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
VCC
DC Supply Voltage
TA
Operating Temperature, All Package Types
Min
Max
Unit
±2.5
or 5.0
±15 or
30
V
-40
+85
°C
This device contains protection circuitry to guard against damage due to high static voltages or
electric fields. However, precautions must be taken to avoid applications of any voltage higher than
maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be
constrained to the range GND≤(VIN or VOUT)≤VCC.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC).
Unused outputs must be left open.
2011, January, ver.01
I L 339
DC ELECTRICAL CHARACTERISTICS (TA=-40 to +85°C)
Guaranteed Limit
Symbol
Parameter
VIO
Input Offset Voltage
Test Conditions
Min
V0=1.4V
VCC=5.0-30V;RS≤100Ω
VICR=0V - (VCC-1.5)V
-
Typ
Max
Unit
9.0
mV
5.0*
IIB
Input Bias Current
V0=1.4V
VCC=5.0-30V
VICR=0V - (VCC-1.5)V
-
400
nA
IIO
Input Offset Current
V0=1.4V
VCC=5.0-30V
VICR=0V - (VCC-1.5)V
-
±150
nA
VICR
Input Common
Mode Voltage
Range
VCC=5.0-30V
0
VCC2.0V
V
ICC
Supply Current
RL=∞,VCC=5.0
-
2.0*
mA
RL=∞,VCC=30V
-
2.5*
Voltage Gain
VCC=15V, RL=15KΩ
-
200*
-
V/mV
t1
Large Signal
Response Time
VIN=TTL Logic Swing,
Vref=1.4V, VCC=5.0V,
RL=5.1KΩ, VRL=5.0V
-
300*
-
ns
t2
Response Time
VCC=5.0V, RL=5.1KΩ,
VRL=5.0V
-
1.3*
-
µs
Isink
Output Sink Current
VI(-)=1.0V, VI(+)=0V,
V0≤1.5V, VCC=5.0V
6.0*
-
-
mA
Vsat
Saturation Voltage
VI(-)=1.0V, VI(+)=0V,
Isink≤4.0mA, VCC=5.0V
-
-
700
mV
IOL
Output Leakage
Current
VI(+)=1.0V, VI(-)=0V,
V0=5.0V
V0=30V
AVOL
VIDR
Differential Input
Voltage Range
All VIN≥GND or V-Supply
(if used)
nA
0.1*
1000
VCC*
V
*[email protected]°C
2011, January, ver.01
I L 339
TYPICAL PERFORMANCE CHARACTERISTICS
(VCC=1.5V, TA=+25°C, (each comporator))
Figure 1. Normalized Input Offset Voltage
Figure 2. Input Bias Current
Figure 3. Output Sink Current versus
Output Saturation Voltage
2011, January, ver.01
I L 339
N SUFFIX PLASTIC DIP
(MS - 001AA)
A
Dimension, mm
8
14
B
7
1
Symbol
MIN
MAX
A
18.67
19.69
B
6.1
7.11
C
F
L
C
-T- SEATING
PLANE
N
G
M
K
J
H
D
0.25 (0.010) M T
NOTES:
1. Dimensions “A”, “B” do not include mold flash or protrusions.
Maximum mold flash or protrusions 0.25 mm (0.010) per side.
5.33
D
0.36
0.56
F
1.14
1.78
G
2.54
H
7.62
J
0°
10°
K
2.92
3.81
L
7.62
8.26
M
0.2
0.36
N
0.38
D SUFFIX SOIC
(MS - 012AB)
Dimension, mm
A
14
8
H
B
1
G
P
7
R x 45
C
-TK
D
SEATING
PLANE
J
0.25 (0.010) M T C M
NOTES:
1. Dimensions A and B do not include mold flash or protrusion.
2. Maximum mold flash or protrusion 0.15 mm (0.006) per side
for A; for B ‑ 0.25 mm (0.010) per side.
F
M
Symbol
MIN
MAX
A
8.55
8.75
B
3.8
4
C
1.35
1.75
D
0.33
0.51
F
0.4
1.27
G
1.27
H
5.27
J
0°
8°
K
0.1
0.25
M
0.19
0.25
P
5.8
6.2
R
0.25
0.5
2011, January, ver.01