IKSEMICON IL4558

TECHNICAL DATA
Dual Operational Amplifiers
IL4558
The IL4558 is dual general purpose operational amplifiers.
The high common-mode input voltage range and the absence
of latch-up make these amplifiers ideal for voltage follower application.
The devices are short circuit protected and the internal frequency
Compensation ensures stability without external components.
FEATURE
•
•
•
•
•
•
•
•
Short Circuit Protection
Wide common-mode and differential ranges
No frequency compensation required
Low power consumption
No latch-up
3 MHz unity gain bandwidth guaranteed
Gain and phase match between amplifiers
Possible to exchange the position of Pin9 for Pin1
because of Pin Connection being symmetric(IL4558S only)
ORDERING INFORMATION
IL4558N Plastic
IL4558D SOIC
IL4558S-9 SIP-9
IL4558S SIP-8
TA = -40° to 85° C for all packages.
BLOCK DIAGRAM
PIN ASSIGNMENT
PIN 4 = GND (V-)
PIN 8 = VCC (V+)
2011, January, Rev. 02
IL4558
SCHEMATIC DIAGRAM
(One Section Only)
MAXIMUM RATINGS*
Symbol
Value
Unit
Supply Voltage
18
V
Supply Voltage
-18
V
VIDR
Differential Input Voltage
±30
V
VIN
Input Voltage
±15
V
PD
Power Dissipation in Still Air
570
mW
Ta
Operation Temperature Ranfe
-40 to 85
°C
Storage Temperature Range
-55 to 125
°C
V
+
-
V
Tstg
Parameter
*
Stresses beyond those listed under “ absolute maximum ratings” may cause permanent damage to the device.
These are stress ratings only and functional operation of the device at these or any other conditions beyond those
indicated under “ recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Functional operation should be restricted to the Recommended Operating Conditions.
RECOMMENDED OPERATING CONDITIONS
Symbol
V
+
-
V
Parameter
Min
Max
Unit
Supply Voltage
16
V
Supply Voltage
-16
V
2011, January, Rev. 02
IL4558
ELECTRICAL CHARACTERISTICS (TA = 25°C, V+ = +15 V, V- = -15 V)
Symbol
Parameter
Test Conditions
Guaranteed Limits
Min
Max
± 5.0
mV
Input Offset Current
± 200
nA
IIB
Input Bias Current
- 500
nA
ri
Input Resistance
VIO
Input Offset Voltage
IIO
AV
VOM
VICR
RS ≤ 10KΩ
Unit
RL ≥ 10KΩ
± 12
V
RL ≥ 2KΩ
± 10
V
± 12
V
70
dB
Input Common-Mode Voltage
Range
PSRR
Supply Voltage Rejection Ratio
RS ≤ 10KΩ
Slew Rate
RL ≥ 2KΩ
I ,I
V/mV
Output Voltage Swing
RS ≤ 10KΩ
-
20
RL ≥ 2KΩ, VC = ± 10V
Common Mode Rejection Ratio
+
MΩ
Large-Signal Voltage Gain
CMRR
SR
0.3
150
0.8
Supply Current
µV/V
1.6
5.6
mA
SR
Slew Rate
RL = 2KΩ
PC
Power Consumption
RL = ∞
170
mW
VN
Input Noise Voltage
RS = 1KΩ
f = 30Hz ∼ 30KHz
3.5
µVrms
Isource
Isink
V/µs
Sourse Current
- 20
mA
Sink Current
20
mA
Transient Response Test Circuit
Unused OpAmp
2011, January, Rev. 02
IL4558
TYPICAL PERFORMANCE CURVES
VOp-p - RL
FREQUENCY f (Hz)
LOAD RESISTANCE RL (kΩ)
VNI - f
VOM - VCC, VEE
FREQUENCY f (Hz)
SUPPLY VOLTAGE V+, V- (±V)
VOp-p- f
II - T A
FREQUENCY f (Hz)
AMBIENT TEMPERATURE TA (°C)
2011, January, Rev. 02
IL4558
2011, January, Rev. 02
IL4558
N SUFFIX PLASTIC DIP
(MS – 001BA)
A
Dimension, mm
5
8
B
1
4
MIN
MAX
A
8.51
10.16
B
6.1
7.11
C
L
F
Symbol
C
5.33
D
0.36
0.56
F
1.14
1.78
-T- SEATING
PLANE
N
G
M
K
0.25 (0.010) M
J
H
D
T
NOTES:
1. Dimensions “A”, “B” do not include mold flash or protrusions.
Maximum mold flash or protrusions 0.25 mm (0.010) per side.
G
2.54
H
7.62
J
0°
10°
K
2.92
3.81
L
7.62
8.26
M
0.2
0.36
N
0.38
D SUFFIX SOIC
(MS - 012AA)
Dimension, mm
A
8
5
B
H
1
G
P
4
D
K
MIN
MAX
A
4.8
5
B
3.8
4
C
1.35
1.75
D
0.33
0.51
F
0.4
1.27
R x 45
C
-T-
Symbol
SEATING
PLANE
J
F
0.25 (0.010) M T C M
NOTES:
1. Dimensions A and B do not include mold flash or protrusion.
2. Maximum mold flash or protrusion 0.15 mm (0.006) per side
for A; for B ‑ 0.25 mm (0.010) per side.
M
G
1.27
H
5.72
J
0°
8°
K
0.1
0.25
M
0.19
0.25
P
5.8
6.2
R
0.25
0.5
2011, January, Rev. 02
IL4558
SIP-9
2011, January, Rev. 02
IL4558
SIP-8
2011, January, Rev. 02