MBR(F,B)1635 thru MBR(F,B)1660 FEATURES • Guardring for overvoltage protection ITO-220AC TO-220AC • Lower power losses, high efficiency • Low forward voltage drop • High forward surge capability 1 1 MBR16xx • High frequency operation 2 2 • Meets MSL level 1, per J-STD-020, LF maximum peak of 245 °C (for TO-263AB package) MBRF16xx PIN 1 PIN 1 • Solder dip 260 °C, 40 s (for TO-220AC and ITO-220AC package) CASE PIN 2 PIN 2 TO-263AB • Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC K 2 TYPICAL APPLICATIONS For use in low voltage, high frequency rectifier of switching mode power supplies, freewheeling diodes, dc-to-dc converters and polarity protection application. 1 MBRB16xx PIN 1 PIN 2 K HEATSINK MECHANICAL DATA Case: TO-220AC, ITO-220AC, TO-263AB Epoxy meets UL 94V-0 flammability rating Terminals: Matte tin plated leads, solderable per J-STD-002 and JESD22-B102 E3 suffix for consumer grade, meets JESD 201 class 1A whisker test, HE3 suffix for high reliability grade (AEC Q101 qualified), meets JESD 201 class 2 whisker test Polarity: As marked Mounting Torque: 10 in-lbs maximum PRIMARY CHARACTERISTICS IF(AV) 16 A VRRM 35 V to 60 V IFSM 150 A VF 0.57 V, 0.65 V TJ max. 150 °C MAXIMUM RATINGS (TC = 25 °C unless otherwise noted) PARAMETER SYMBOL MBR1635 MBR1645 MBR1650 MBR1660 UNIT Maximum repetitive peak reverse voltage VRRM 35 45 50 60 V Working peak reverse voltage VRWM 35 45 50 60 V Maximum DC blocking voltage VDC 35 45 50 60 V Maximum average forward rectified current at TC = 125 °C IF(AV) 16 A Peak forward surge current 8.3 ms single half sine-wave superimposed on rated load IFSM 150 A Peak repetitive reverse current at tp = 2.0 µs, 1 kHz IRRM Voltage rate of change (rated VR) dV/dt 10 000 V/µs Operating junction temperature range 1.0 0.5 A TJ - 65 to + 150 °C Storage temperature range TSTG - 65 to + 175 °C Isolation voltage (ITO-220AC only) from terminal to heatsink t = 1 min VAC 1500 V www.kersemi.com 1 MBR(F,B)1635 thru MBR(F,B)1660 ELECTRICAL CHARACTERISTICS (TC = 25 °C unless otherwise noted) PARAMETER TEST CONDITIONS Maximum instantaneous forward voltage (1) IF = 16 A IF = 16 A Maximum instantaneous reverse current at rated DC blocking voltage (1) SYMBOL MBR1635 MBR1645 MBR1650 MBR1660 UNIT TC = 25 °C TC = 125 °C VF 0.63 0.57 0.75 0.65 V TC = 25 °C TC = 125 °C IR 0.2 40 1.0 50 mA Note: (1) Pulse test: 300 µs pulse width, 1 % duty cycle THERMAL CHARACTERISTICS (TC = 25 °C unless otherwise noted) PARAMETER Typical thermal resistance from junction to case SYMBOL MBR MBRF MBRB UNIT RθJC 1.5 3.0 1.5 °C/W ORDERING INFORMATION (Example) PACKAGE PREFERRED P/N UNIT WEIGHT (g) PACKAGE CODE BASE QUANTITY DELIVERY MODE TO-220AC MBR1645-E3/45 1.80 45 50/tube Tube ITO-220AC MBRF1645-E3/45 1.94 45 50/tube Tube TO-263AB MBRB1645-E3/45 1.33 45 50/tube Tube TO-263AB MBRB1645-E3/81 1.33 81 800/reel Tape reel TO-220AC MBR1645HE3/45 (1) 1.80 45 50/tube Tube ITO-220AC MBRF1645HE3/45 (1) 1.94 45 50/tube Tube TO-263AB MBRB1645HE3/45 (1) 1.33 45 50/tube Tube TO-263AB MBRB1645HE3/81 (1) 1.33 81 800/reel Tape reel Note: (1) Automotive grade AEC Q101 qualified RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted) 20 150 TJ = TJ Max. 8.3 ms Single Half Sine-Wave Peak Forward Surge Current (A) Average Forward Current (A) Resistive or Inductive Load 16 12 8 4 0 125 100 75 50 25 0 50 0 100 150 1 10 100 Case Temperature (°C) Number of Cycles at 60 Hz Figure 1. Forward Current Derating Curve Figure 2. Maximum Non-Repetitive Peak Forward Surge Current www.kersemi.com 2 MBR(F,B)1635 thru MBR(F,B)1660 10 000 TJ = 150 °C Junction Capacitance (pF) Instantaneous Forward Current (A) 100 10 Pulse Width = 300 µs 1 % Duty Cycle 1 TJ = 25 °C 0.1 1000 MBR1635 - MBR1645 MBR1650 - MBR1660 MBR1635 - MBR1645 MBR1650 - MBR1660 0.01 100 0 0.2 0.4 0.6 0.8 1.0 1 0.1 1.2 100 10 Instantaneous Forward Voltage (V) Reverse Voltage (V) Figure 3. Typical Instantaneous Forward Characteristics Figure 5. Typical Junction Capacitance 100 100 MBR1635 - MBR1645 MBR1650 - MBR1660 Transient Thermal Impedance (°C/W) Instantaneous Reverse Current (mA) TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p TJ = 125 °C 10 1 TJ = 75 °C 0.1 TJ = 25 °C 0.01 0.001 0 20 40 60 80 100 10 1 0.1 0.01 0.1 1 10 100 Percent of Rated Peak Reverse Voltage (%) t - Pulse Duration (s) Figure 4. Typical Reverse Characteristics Figure 6. Typical Transient Thermal Impedance www.kersemi.com 3 MBR(F,B)1635 thru MBR(F,B)1660 PACKAGE OUTLINE DIMENSIONS in inches (millimeters) ITO-220AC TO-220AC 0.404 (10.26) 0.384 (9.75) 0.415 (10.54) MAX. 0.370 (9.40) 0.360 (9.14) 0.154 (3.91) DIA. 0.148 (3.74) DIA. 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 1 PIN 2 0.560 (14.22) 0.530 (13.46) 0.057 (1.45) 0.045 (1.14) 0.028 (0.71) 0.020 (0.51) 0.205 (5.21) 0.195 (4.95) TO-263AB 0.411 (10.45) 0.380 (9.65) 0.190 (4.83) 0.160 (4.06) 0.245 (6.22) MIN. 0.055 (1.40) 0.045 (1.14) Mounting Pad Layout 0.42 (10.66) MIN. K 0.360 (9.14) 0.320 (8.13) 1 K 2 0.624 (15.85) 0.591 (15.00) 0.037 (0.940) 0.027 (0.686) 0.105 (2.67) 0.095 (2.41) www.kersemi.com 4 0.055 (1.40) 0.047 (1.19) 0 to 0.01 (0 to 0.254) 0.110 (2.79) 0.090 (2.29) 0.021 (0.53) 0.014 (0.36) 0.205 (5.20) 0.195 (4.95) 0.140 (3.56) 0.110 (2.79) 0.110 (2.79) 0.100 (2.54) 0.035 (0.89) 0.025 (0.64) 0.025 (0.64) 0.015 (0.38) 0.022 (0.56) 0.014 (0.36) 0.205 (5.20) 0.195 (4.95) 7° REF. 0.191 (4.85) 0.171 (4.35) CASE 0.037 (0.94) 0.027 (0.68) 7° REF. 2 1 0.560 (14.22) 0.530 (13.46) PIN 1 0.135 (3.43) DIA. 0.122 (3.08) DIA. 0.350 (8.89) 0.330 (8.38) 0.110 (2.79) 0.100 (2.54) PIN 2 0.105 (2.67) 0.095 (2.41) 0.671 (17.04) 0.651 (16.54) PIN 1.148 (29.16) 1.118 (28.40) 0.160 (4.06) 0.140 (3.56) 0.057 (1.45) 0.045 (1.14) 0.140 (3.56) DIA. 0.125 (3.17) DIA. 0.600 (15.24) 0.580 (14.73) 0.603 (15.32) 0.573 (14.55) 0.350 (8.89) 0.330 (8.38) 7° REF. 0.076 (1.93) REF. 45° REF. 0.635 (16.13) 0.625 (15.87) 0.190 (4.83) 0.170 (4.32) 0.110 (2.79) 0.100 (2.54) 0.076 (1.93) REF. 0.185 (4.70) 0.175 (4.44) 0.055 (1.39) 0.045 (1.14) 0.33 (8.38) MIN. 0.670 (17.02) 0.591 (15.00) 0.15 (3.81) MIN. 0.08 (2.032) MIN. 0.105 (2.67) 0.095 (2.41)