RECTANGULAR CONNECTORS FCN360 Series FCN-365J FCN-365P FCN-364P FCN-364P FCN-364J FCN-364J FCN-365J FCN-364P FCN-365P FCN-364J FCN-362J FCN-363J FCN-365P FCN-367J FCN-361P FCN-365P FCN-364P FCN-365J With type B cover FCN-364P FCN-365P With type E cover FCN-364J With type J1 cover Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 1 Terms in Selection Table (Example) 700 series Model Appearance Contact pitch Denotes a pitch between adjacent contacts or pitch between rows. 2.54 mm (0.100 in.) (pitch between adjacent contacts) x 2.54 mm (0.100 in.) (pitch between rows) Number of contacts Denotes the numbers of contacts of available connectors. 2.54 × 2.54 Contact pitch Number of contacts 10, 14, 16, 20, 26, 30, 34, 40, 50, 60 Wire-wrapping (post cross section) Pin type Structure Solder eyelet (tail shape) 0.64 Straight, throughhole (PC board hole dimensions) IDC (applicable AWG No.) φ 0.8, 2.54 × 2.54 P J P J φ 0.8, 2.54 × 2.54 #28, Flat cable #28, Flat cable Gold Silver Specification Tin Operating temperature range –55°C to +105°C Current rating DC 1 A Voltage rating AC 250 V Contact resistance 20 mΩ max. (DC 6 V, 0.1 A) Insulation resistance (DC 500 V) 1,000MΩ min. Dielectric withstanding voltage (for 1 minute) AC 500 V Insulation material cleaning with Chlorothene Polyester cleaning possible Part number (example) FCN-705P050-AU/M FCN-707J050-AU/B Remarks Plating Denotes the contact plating specification. Specifications 4 Operating temperature range The connector can be used within the specified temperature range. Crimping (applicable AWG No.) Right-angle, throughhole (PC board hole dimensions) Plating P J Connection type Denotes the connection type of the cable or PC board connection section. EMI protection cover provided Current rating Maximum current that can flow through one connector pin Voltage rating Maximum voltage that can be applied to a connector Contact resistance Resistance observed at the contact part when 0.3 A (or 0.1 A) flows at 6 VDC with the connectors mated Insulation resistance Resistance to the leakage current flowing through the insulator (inside or surface of the insulator) when 500 VDC is applied across adjacent pins of a connector Dielectric withstanding voltage Applying the indicated voltage across adjacent pins of a connector for one minute does not cause any abnormality (damage or cracks in insulator). Insulating material, cleaning with chlorothene Denotes the insulating material used, and indicates whether the insulating material can be cleaned with chlorothene. Part number Some part numbers are indicated as examples. 4-2 Selection Table Rectanglar Connectors 360 series Model Appearance Contact pitch 2.54 × 2.54 Number of contacts 8, 16, 24, 32, 40, 48, 56, 64 P J Wire-wrapping (post cross section) Pin type Structure Solder eyelet (tail shape) Plating 1.8 × 0.7 1.8 × 0.7 4 Diagonal 0.71 mm (0.028 in.) Crimping ( applicable AWG No.) P J AWG #22 to #28 Straight, through hole (PC board hole dimensions) Right-angle, through hole (PC board hole dimensions) P J P J φ1, 2.54 × 2.54 φ1, 2.54 × 2.54 φ1, 2.54 × 2.54 φ1, 2.54 × 2.54 IDC ( applicable AWG No.) P J #28, Flat cable Gold Silver Specification Tin Operating temperature range –55°C to +85°C Current rating DC 3 A (IDC type: 1A) Voltage rating AC 250 V Contact resistance 15 mΩ max. (DC 6 V, 0.3 A) Insulation resistance (DC 500 V) 1,000 MΩ min. Dielectric withstanding voltage (for 1 minute) AC 500 V Insulating material Polyester PC (363J) Part number (example) Remarks FCN-361P024-AU Cable cover provided 4-3 FCN-360 Series NOTES Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 4 RECTANGULAR CONNECTORS FCN-360 SERIES ■ FEATURES • Many applications Various connectors are available for connection by means of soldering, wire wrapping, crimping, PC board mounting, and insulation displacement connection (IDC). The user can choose a plug and jack combination that best meet each application. • Small size for high-density mounting The connectors are small with a contact and terminal pitch of 2.54 mm (0.100 in.) between pins and between rows and are thus well suited for high-density mounting. • Sturdy shell guide Sturdy shell guides are used to prevent mismating and to protect the pins. • Excellent cost performance Streamlined design and automated manufacturing, including use of partial solder plating, provide excellent cost performance. ■ SPECIFICATIONS ■ MATERIALS Specification Item Item Material Operating temperature range –55°C to +85°C Insulator Polyester (363J: PC94V-2) Current Rating DC 3 A (IDC type: 1 A) Conductor Copper alloy Voltage Rating AC 250 V Plating Gold plating, silver plating Contact resistance 15 mΩ max. (DC 6 V, 0.3 A) Insulation resistance 1000 MΩ min. (DC 500 V) Dielectric withstanding voltage AC 500 V for 1 minute Insertion force 2.5 kg max. (8 contacts), 20 kg max. (64 contacts) Withdrawal force 0.3 kg min. (8 contacts), 2.3 kg min. (64 contacts) Applicable wire Soldering φ0.60 mm (0.024 in.) max, AWG #23 or less Wire-wrapping φ0.32 mm (0.013 in.) to φ0.26 mm (0.010 in.), AWG #28 to #30 Crimping Standard contacts φ0.51 mm (0.020 in.) to φ0.32 mm (0.013 in.), AWG #24 to #28, insulator φ1.2 mm (0.047 in.) max. Contacts for thick wires φ0.64 mm (0.025 in.) to φ0.32 mm (0.013 in.), AWG #22 to #28, insulator φ1.7 (0.067 in.) max. IDC Flat cable 1.27 mm (0.050 in.) pitch, AWG #28 (stranded wire), AWG #30 (solid wire) Applicable PC board Specifications subject to change 1.6 mm (0.063 in.) standard thick Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 5 FCN-360 Series ■ PART NUMBER FCN-36 7 J 048-AU / H (Only for IDC) Shape of connector cover with IDC holders B: Close end (special) F: Close end H: Through end Plating and cover specification AU: Gold plating B: Type B cover (standard) C: Type C cover (for cable-to-cable connection) D: Type D cover (with metal cable clamp) E: Type E cover (with long lock-screws) F: Type F cover (64 contacts only) G1: One-touch lock type (40 contacts only) H/E: EMI protection type (40 contacts only) J1: Obtuse angle cable-out cover (40 contacts only) Number of contacts 8, 16, 24, 32, 40, 48, 56, 64 Connector or parts type A: Metal fitting C: Cover J: Jack P: Plug Tail type 0: Cover, metal fitting 1: Soldering 2: Wire-wrapping 3: Crimping 4: Straight 5: Right-angle 7: IDC 360 series connector Fujitsu connector Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 6 FCN-360 Series ■ APPLICATION EXAMPLE FCN-365J FCN-365P FCN-364P FCN-364P FCN-364J FCN-364J FCN-365J FCN-364P FCN-365P FCN-364J FCN-362J FCN-363J FCN-365P FCN-367J FCN-361P FCN-365P FCN-364P FCN-365J With type B cover FCN-364P FCN-365P With type E cover FCN-364J With type J1 cover FCN-365P FCN-365J With type G1 cover With type Ccover With type H/E cover Specifications subject to change Dimensions are in millimeters (inches) With type E cover www.fujitsu.takamisawa.com 7 FCN-360 Series 6 (0.236) 2.54 (0.10) 8.25 (0.324) SOLDERING TYPE (PLUG) ■ DIMENSIONS 2.54 (0.10) B 5 (0.196) 4 (0.157) A 5.8 (0.228) 12.1 (0.476) D 0.7 (0.027) B A 1.5 (0.059) 1 2 C φ2.8 (0.110) Unit: mm (in.) 8.6(0.338) ±0.2(0.007) ■ MOUTING HOLE LAYOUT [Panel] (C + 1)±0.3 ((C + 0.039)±0.011 ) B +0.15(0.005) φ2.8(0.110) –0 hole Unit: mm (in.) ±0.15 (0.005) ■ PART NUMBERS AND DIMENSIONS Dimensions: mm (in.) Number of contacts Part number A B C D 8 FCN-361P008-AU 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FCN-361P016-AU 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FCN-361P024-AU 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FCN-361P032-AU 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FCN-361P040-AU 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FCN-361P048-AU 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FCN-361P056-AU 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FCN-361P064-AU 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 8 FCN-360 Series 2.54 (0.10) 6 (0.236) 8.25 (0.324) SOLDERING TYPE (JACK) ■ DIMENSIONS 2.54 (0.10) D A 5 (0.198) 4 (0.157) 6 (0.236) 5.8 (0.228) 10.8 (0.425) B 0.7 (0.027) 0.5 (0.019) 1.5 (0.059) A B 1 C φ2.8 (0.110) Unit: mm (in.) 8.6 (0.338) ±0.2(0.007) ■ BOARD MOUTING HOLE LAYOUT [Panel] (C + 1)±0.3 ((C + 0.039) ±0.011 ) B +0.15(0.005) φ2.8 (0.110) –0 hole Unit: mm (in.) ±0.15 (0.005) ■ PART NUMBERS AND DIMENSIONS Dimensions: mm (in.) Number of contacts Part number A B C D 8 FCN-361J008-AU 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FCN-361J016-AU 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FCN-361J024-AU 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FCN-361J032-AU 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FCN-361J040-AU 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FCN-361J048-AU 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FCN-361J056-AU 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FCN-361J064-AU 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 9 FCN-360 Series 2.54 (0.10) 8.25 (0.324) WIRE-WRAP TYPE (PLUG) ■ DIMENSIONS 2.54 (0.10) D B 10.8 (0.425) 4 (0.157) 10.3 (0.405) A 0.71 (0.027) B A Diagonal length C φ2.8 (0.110) Unit: mm (in.) [Board] D B [Panel] (C + 1) ±0.3 ((C + 0.039)±0.011 ) +0.15(0.005) φ2.8 (0.110) –0 hole ±0.2 (0.007) ±0.15 (0.005) 8.6 (0.338) ±0.2(0.007) 2.54 (0.10) ±0.15(0.009) ■ MOUTING HOLE LAYOUT φ1 (0.039)+0.1(0.0034) hole B +0.15(0.005) φ2.8 (0.110) –0 hole ±0.15 (0.005) Unit: mm (in.) ■ PART NUMBERS AND DIMENSIONS Number of contacts Part number 8 Dimensions: mm (in.) A B C D FCN-362P008-AU 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FCN-362P016-AU 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FCN-362P024-AU 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FCN-362P032-AU 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FCN-362P040-AU 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FCN-362P048-AU 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FCN-362P056-AU 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FCN-362P064-AU 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 10 FCN-360 Series 2.54 (0.10) 6 (0.236) 8.25 (0.324) WIRE-WRAP TYPE (JACK) ■ DIMENSIONS 2.54 (0.10) D A 13.5 (0.531) 5.8 (2.283) 6 (0.236) 4 (0.157) 10.8 (0.425) B 0.71 (0.027) Diagonal length 1 A B C φ2.8 (0.110) Unit: mm (in.) D ±0.2 (0.007) B ±0.15 (0.005) 8.6 (0.338) ±0.2(0.007) [Board] 2.54 (0.10) ±0.15(0.009) ■ MOUTING HOLE LAYOUT [Panel] (C + 1) ±0.3 ((C + 0.039) ±0.011 ) +0.15(0.005) φ2.8 (0.110) –0 hole φ1 (0.039) +0.1(0.0034) hole B φ2.8 (0.110) +0.15(0.005) hole –0 Unit: mm (in.) ±0.15 (0.005) ■ PART NUMBERS AND DIMENSIONS Number of contacts Part number 8 Dimensions: mm (in.) A B C D FCN-362J008-AU 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FCN-362J016-AU 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FCN-362J024-AU 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FCN-362J032-AU 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FCN-362J040-AU 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FCN-362J048-AU 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FCN-362J056-AU 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FCN-362J064-AU 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 11 FCN-360 Series 2.54 (0.10) 6 (0.236) 8.25 (0.324) CRIMP TYPE (JACK HOUSING) ■ DIMENSIONS 2.54 (0.10) D 10.8 (0.425) B 5.8 (2.283) A 4 (0.157) 22 (0.866) 6 (0.236) C 6 (0.236) Pin 1 in row A φ2.8 (0.110) Pin 1 in row B Unit: mm (in.) 8.6 (0.338) ±0.2(0.007) ■ MOUTING HOLE LAYOUT [Panel] (C + 1)±0.3 ((C + 0.039)±0.011 ) B +0.15(0.005) φ2.8 (0.110) –0 hole Unit: mm (in.) ±0.15 (0.005) ■ PART NUMBERS AND DIMENSIONS Number of contacts 8 16 24 32 40 48 56 64 Part number FCN-363J008 FCN-363J016 FCN-363J024 FCN-363J032 FCN-363J040 FCN-363J048 FCN-363J056 FCN-363J064 Specifications subject to change A 28.84 (1.135) 39.0 (1.535) 49.16 (1.935) 59.32 (2.335) 69.48 (2.735) 79.64 (3.135) 89.8 (3.535) 99.96 (3.935) Dimensions: mm (in.) B C 23.34 (0.918) 17.84 (0.702) 33.5 (1.318) 28.0 (1.102) 43.66 (1.718) 38.16 (1.502) 53.82 (2.118) 48.32 (1.902) 63.98 (2.518) 58.48 (2.302) 74.14 (2.918) 68.64 (2.702) 84.3 (3.318) 78.8 (3.102) 94.46 (3.718) 88.96 (3.502) Dimensions are in millimeters (inches) D 7.62 (0.3) 17.78 (0.7) 27.94 (1.1) 38.1 (1.5) 48.26 (1.9) 58.42 (2.3) 68.58 (2.7) 78.74 (3.1) www.fujitsu.takamisawa.com 12 FCN-360 Series CRIMP TYPE (CONTACT) ■ DIMENSIONS Standard contact (applicable wire: AWG #24 to #28) Thick wire connection contact (applicable wire: AWG #22 to #26) 20.05 (0.789) 20.05 (0.789) Unit: mm (in.) ■ PART NUMBERS Type Plating Standard Thick wire connection contact Loose piece Gold plating FCN-363J-AU FCN-363J-AU/S Strip reeled Gold plating FCN-363J-AU/R FCN-363J-AU/T ■ PART NUMBERS OF CRIMPING TOOLS Part number Contact type Applicable wire Wire cross-section area (mm2) Crimp height Stripped length Insulator diameter FCN-363T-T005/H (Hand crimping tool) FCN-363J-AU (Loose piece) AWG #24 0.20 to 0.24 1.25 mm (0.049 in.) to φ1.2 mm 1.30 mm (0.051 in.) (0.047 in.) max 3.0 mm (0.118 in.) to 4.0 mm (0.157 in.) FCN-M110 (Automatic crimping machine) FCN-363J-AU/R (Strip reeled) AWG #26 0.13 to 0.16 1.20 mm (0.047 in.) to φ1.2 mm 1.25 mm (0.049 in.) (0.047 in.) max 3.0 mm (0.118 in.) to 4.0 mm (0.157 in.) AWG #28 0.088 to 0.096 1.15 mm (0.045 in.) to φ1.2 mm 1.20 mm (0.047 in.) (0.047 in.) max 3.0 mm (0.118 in.) to 4.0 mm (0.157 in.) FCN-A105 (Applicator) FCN-363T-T011/H (Hand crimping tool) FCN-363J-AU/S (Loose piece) AWG #22 0.30 to 0.40 0.85 mm (0.033 in.) to φ0.9 mm (0.035 in.) 3.0 mm (0.118 in.) to 0.95 mm (0.037 in.) 1.8 mm (0.071 in.) 4.0 mm (0.157 in.) FCN-M110 (Automatic crimping machine) FCN-363J-AU/T (Strip reeled) AWG #24 0.20 to 0.24 0.75 mm (0.029 in.) to φ0.9 mm (0.035 in.) 3.0 mm (0.118 in.) to 0.85 mm (0.033 in.) 1.8 mm (0.071 in.) 4.0 mm (0.157 in.) AWG #26 0.13 to 0.16 0.73 mm (0.028 in.) to φ0.9 mm (0.035 in.) 3.0 mm (0.118 in.) to 0.81 mm (0.031 in.) 1.8 mm (0.071 in.) 4.0 mm (0.157 in.) FCN-A111 (Applicator) [Semi-automatic crimping machine, [Contact withdrawal tool] applicator] 10 (0.393) [Hand crimping tool] 65 (2.559) FCN-360T-T001/H Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 13 FCN-360 Series 2.54 (0.10) 8.25 (0.324) STRAIGHT TYPE (PLUG) ■ DIMENSIONS 2.54 (0.10) D A 4.2 (0.165) 4 (0.157) 10.3 (0.405) B 0.71 (0.027) Diagonal length B A 1 φ2.8 (0.110) C Unit: mm (in.) 2.54 (0.10) ±0.15(0.009) ■ BOARD MOUTING HOLE LAYOUT [Board] ±0.2 (0.007) D B ±0.15 (0.005) +0.15(0.005) φ2.8 (0.110) –0 hole φ1 (0.039) +0.1(0.0034) hole Unit: mm (in.) ■ PART NUMBERS AND DIMENSIONS Number of contacts Part number 8 Dimensions: mm (in.) A B C D FCN-364P008-AU 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FCN-364P016-AU 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FCN-364P024-AU 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FCN-364P032-AU 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FCN-364P040-AU 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FCN-364P048-AU 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FCN-364P056-AU 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FCN-364P064-AU 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 14 FCN-360 Series 2.54 (0.10) 6 (0.236) 8.25 (0.324) STRAIGHT TYPE (JACK) ■ DIMENSIONS 2.54 (0.10) D A 5.8 (0.228) 6 (0.236) 4 (0.157) 4.2 (0.165) 10.8 (0.425) B 0.71 (0.027) Diagonal length φ2.8 (0.110) A B 1 C Unit: mm (in.) 2.54 (0.10) ±0.15(0.009) ■ BOARD MOUTING HOLE LAYOUT [Board] D B ±0.2 (0.007) ±0.15 (0.005) φ2.8 (0.110) +0.15(0.005) hole –0 φ1 (0.039) +0.1(0.0034) hole Unit: mm (in.) ■ PART NUMBERS AND DIMENSIONS Number of contacts Part number 8 Dimensions: mm (in.) A B C D FCN-364J008-AU 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FCN-364J016-AU 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FCN-364J024-AU 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FCN-364J032-AU 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FCN-364J040-AU 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FCN-364J048-AU 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FCN-364J056-AU 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FCN-364J064-AU 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 15 FCN-360 Series 4 (0.157) 2.54 (0.10) 8.25 (0.324) RIGHT-ANGLE TYPE (JACK) ■ DIMENSIONS 2.54 (0.10) D C 2.54 (0.10) φ2.8 (0.110) 8 (0.314) 5 (0.196) 5 (0.196) 11 (0.433) A 3 (0.118) B AB 1 0.8 (0.031) Diagonal length Unit: mm (in.) D ±0.2 (0.007) 2.54 (0.10) ±0.15(0.009) Edge of board 5 (0.196) [Board] 3.27 (0.128) ±0.15(0.005) ■ MOUTING HOLE LAYOUT • Note on mounting a right-angle jack on a board Mount the connector so that it projects from the board by at least 5 mm (0.197 in.). +0.15(0.005) φ2.8 (0.110)–0 hole B ±0.15 (0.005) φ1 (0.039) +0.1(0.0034) hole Unit: mm (in.) ■ PART NUMBERS AND DIMENSIONS Number of contacts Part number 8 Dimensions: mm (in.) A B C D FCN-365J008-AU 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FCN-365J016-AU 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FCN-365J024-AU 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FCN-365J032-AU 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FCN-365J040-AU 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FCN-365J048-AU 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FCN-365J056-AU 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FCN-365J064-AU 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 18 FCN-360 Series IDC TYPE (JACK) ■ DIMENSIONS [Connector body] 2.54 (0.10) A B 5 (0.196) 11.5 (0.452) C 8.25 (0.324) 6 (0.236) 2.54 (0.10) 4 (0.157) A [Closed-end type] [Strain relief] 8.25 (0.324) 5 (0.196) 4 (0.157) 5 (0.196) [Connector cover with IDC holders] 8.25 (0.324) 8.25 (0.324) A [Through-end type] 6 (0.236) 15.7 (0.618) A 10 (0.393) 31 (1.220) [Lock-screw] M2.6 (0.102) φ5 (0.196) Unit: mm (in.) ■ PART NUMBERS AND DIMENSIONS Number of contacts Part number Through-end cover Close-end cover A Dimensions: mm (in.) B D 8 FCN-367J008-AU/H FCN-367J008-AU/F 28.84 (1.135) 23.34 (0.918) 7.62 (0.3) 16 FCN-367J016-AU/H FCN-367J016-AU/F 39.0 (1.535) 33.5 (1.318) 17.78 (0.7) 24 FCN-367J024-AU/H FCN-367J024-AU/F 49.16 (1.935) 43.66 (1.718) 27.94 (1.1) 32 FCN-367J032-AU/H FCN-367J032-AU/F 59.32 (2.335) 53.82 (2.118) 38.1 (1.5) 40 FCN-367J040-AU/H FCN-367J040-AU/F 69.48 (2.735) 63.98 (2.518) 48.26 (1.9) 48 FCN-367J048-AU/H FCN-367J048-AU/F 79.64 (3.135) 74.14 (2.918) 58.42 (2.3) 56 FCN-367J056-AU/H FCN-367J056-AU/F 89.8 (3.535) 84.3 (3.318) 68.58 (2.7) 64 FCN-367J064-AU/H FCN-367J064-AU/F 99.96 (3.935) 94.46 (3.718) 78.74 (3.1) Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 19 FCN-360 Series IDC TOOLS Special IDC tools are used to assemble FCN-360 series connectors and flat cables. ■ FEATURES • The mechanisms are simple, so even novices can use them easily. • Those who already have Fujitsu-manufactured IDC tools for other series connectors need only purchase the locator plate. The hand press and cable cutter are designed to be used in common with all connectors. • The assembly of cables and connectors with various numbers of contacts can be done by selective setting of the connector guides to the specified positions. Hand press Cable cutter • The cable cutter has an extremely sharp cutting edge. Locator plate (That for the 790 series is shown in the photograph.) Notes: • A detailed operation manual and instruction manual for IDC tools are available upon request. • Should any question arise in using the IDC tools, consult our branch offices or agents in your area. ■ ORDERING CODES FOR IDC TOOLS Tool name Part number Cable cutter (common) FCN-707T-T001/H Hand press (common) FCN-707T-T101/H Locator plate (for 360 series connectors) FCN-367T-T012/H The hand press and cable cutter can be used for other IDC connectors. COVER ■ COMBINATIONS BETWEEN COVERS AND CONNECTORS Connector Cover Plug Soldering Jack Soldering Wire-wrapping Number of contacts Crimping 8 16 24 32 40 48 56 64 FCN-360C ■■■ ■■■-B FCN-360C ■■■ ■■■-C FCN-360C ■■■ ■■■-D FCN-360C ■■■ ■■■-E FCN-360C064-F FCN-360C040-G1 FCN-360C040-H/E FCN-360C040-J1 These covers cannot be used for IDC connectors. Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 20 FCN-360 Series COVER (TYPE B) ■ DIMENSIONS R: 2.84 mm (0.112 in.) (8 and 16 contacts) R: 4.0 mm (0.157 in.) (24 to 64 contacts) G H R 14 mm (0.551 in.) max 10.3 (0.405) 46 (1.811) 37 (1.456) 28 (1.102) B 1 (0.039) FUJITSU F Unit: mm (in.) ■ EXPLODED VIEW Two M2 mm (0.079 in.) thread × 8 mm (0.315 in.) long pan head machine screws (shorter) Four M2 mm (0.079 in.) thread nuts Two M2 mm (0.079 in.) thread × 10 mm (0.394 in.) long pan head machine screws (longer) Two washers Case Connector Two lock-screws Note: The screws, nuts, washers, and lock-screws are attached to the cover. ■ PART NUMBERS AND DIMENSIONS Number of contacts 8 16 24 32 40 48 56 64 Part number FCN-360C008-B FCN-360C016-B FCN-360C024-B FCN-360C032-B FCN-360C040-B FCN-360C048-B FCN-360C056-B FCN-360C064-B Specifications subject to change B 23.34 (0.918) 33.50 (1.318) 43.66 (1.718) 53.82 (2.118) 63.98 (2.518) 74.14 (2.918) 84.30 (3.318) 94.46 (3.718) Dimensions: mm (in.) F G 32.08 (1.262) — 42.24 (1.662) — 52.40 (2.062) — 62.56 (2.462) 2.0 (0.078) 72.72 (2.862) 6.0 (0.236) 82.88 (3.262) 10.0 (0.393) 93.04 (3.662) 14.0 (0.551) 103.20 (4.062) 18.0 (0.708) Dimensions are in millimeters (inches) H φ 5.7 (0.224) φ 5.7 (0.224) φ 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) www.fujitsu.takamisawa.com 21 FCN-360 Series COVER FOR CABLE TO CABLE CONNECTION (TYPE C) ■ DIMENSIONS G R: 2.84 mm (0.112 in.) (8 and 16 contacts) R H R: 4.0 mm (0.157 in.) (24 and 64 contacts) 14 mm (0.551 in.) max. Note: This cover can be combined with a cover of type B, D, or E for cableto-cable connection. 46 (1.811) 28 (1.102 10.3 (0.405) 1 (0.039) FUJITSU F Metal fittings Unit: mm (in.) ■ EXPLODED VIEW Two M2 mm (0.079 in.) thread × 8 mm (0.315 in.) long pan head machine screws (shorter) Four M2 mm (0.079 in.) thread nuts Two M2 mm (0.079 in.) thread × 10 mm (0.394 in.) long pan head machine screws (longer) Two screws for mounting metal fittings Two washers Connector Case Two metal fittings Connector Note: The screws, nuts, washers, and accessory are attached to the cover. ■ PART NUMBERS AND DIMENSIONS Number of contacts 8 16 24 32 40 48 56 64 Part number FCN-360C008-C FCN-360C016-C FCN-360C024-C FCN-360C032-C FCN-360C040-C FCN-360C048-C FCN-360C056-C FCN-360C064-C Specifications subject to change F 32.08 (1.262) 42.24 (1.662) 52.40 (2.062) 62.56 (2.462) 72.72 (2.862) 82.88 (3.262) 93.04 (3.662) 103.20 (4.062) Dimensions are in millimeters (inches) Dimensions: mm (in.) G — — — 2.0 (0.078) 6.0 (0.236) 10.0 (0.393) 14.0 (0.551) 18.0 (0.708) H φ 5.7 (0.224) φ 5.7 (0.224) φ 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) www.fujitsu.takamisawa.com 22 FCN-360 Series COVER (WIDE OPENING TYPE) (TYPE D) ■ DIMENSIONS 10.5 (0.413) I 7.5 (0.295) Cable clamp 14 mm (0.551 in.) max. B FUJITSU 46 (1.811) 37 (1.456) 28 (1.102) 1 (0.039) 10.3 (0.405) F Unit: mm (in.) ■ EXPLODED VIEW Four M2 mm (0.079 in.) thread × 8 mm (0.315 in.) long pan head machine screws (shorter) Four M2 mm (0.079 in.) thread nuts Two cable clamps Case Connector Two lock-screws Note: The screws, nuts, cable clamp, and lockscrews are attached to the cover. ■ PART NUMBERS AND DIMENSIONS Number of contacts 40 48 56 64 Part number FCN-360C040-D FCN-360C048-D FCN-360C056-D FCN-360C064-D Specifications subject to change B 63.98 (2.518) 74.14 (2.918) 84.30 (3.318) 94.46 (3.718) Dimensions are in millimeters (inches) Dimensions: mm (in.) F 72.72 (2.862) 82.88 (3.262) 93.04 (3.662) 103.20 (4.062) I 8.0 (0.314) 12.0 (0.472) 16.0 (0.629) 20.0 (0.789) www.fujitsu.takamisawa.com 23 FCN-360 Series COVER (LONG-SCREW TYPE) (TYPE E) ■ DIMENSIONS R G R: 2.84 mm (0.112 in.) (8 and 16 contacts) H R: 4.0 mm (0.157 in.) (24 and 64 contacts) 14 mm (0.551 in.) max. B FUJITSU 53 (2.086) 46 (1.811) 28 (1.102) 1 (0.039) 10.3 (0.405) F Unit: mm (in.) ■ EXPLODED VIEW Two M2 mm (0.079 in.) thread × 8 mm (0.315 in.) long pan head machine screws (shorter) Four M2 mm (0.079 in.) thread nuts Two M2 mm (0.079 in.) thread × 10 mm (0.394 in.) long pan head machine screws (longer) Two washers Case Connector Two lock-screws Note: The screws, nuts, washers, and lock-screws are attached to the cover. ■ PART NUMBERS AND DIMENSIONS Number of contacts 8 16 24 32 40 48 56 64 Part number FCN-360C008-E FCN-360C016-E FCN-360C024-E FCN-360C032-E FCN-360C040-E FCN-360C048-E FCN-360C056-E FCN-360C064-E Specifications subject to change B 23.34 (0.918) 33.50 (1.318) 43.66 (1.718) 53.82 (2.118) 63.98 (2.518) 74.14 (2.918) 84.30 (3.318) 94.46 (3.718) Dimensions: mm (in.) F G 32.08 (1.262) — 42.24 (1.662) — 52.40 (2.062) — 62.56 (2.462) 2.0 (0.078) 72.72 (2.862) 6.0 (0.236) 82.88 (3.262) 10.0 (0.393) 93.04 (3.662) 14.0 (0.551) 103.20 (4.062) 18.0 (0.708) Dimensions are in millimeters (inches) H φ 5.7 (0.224) φ 5.7 (0.224) φ 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) www.fujitsu.takamisawa.com 24 FCN-360 Series COVER (STRAIGHT CABLE-OUT COVER) (TYPE F) ■ DIMENSIONS Section S 19.5 (0.767) 17.5 (10.688) 10 (0.393) 6 (0.236) 94.46 (3.718) 8 (0.314) Detail of section S 14 mm (0.551 in.) max. 30.5 (1.200) FUJITSU 103.2 (4.062) 55 (2.165) 46 (1.811) 37 (1.456) 1 (0.039) 28 (1.102) 10.3 (0.405) Unit: mm (in.) ■ EXPLODED VIEW Six M2 mm (0.079 in.) thread × 8 mm (0.315 in.) long pan head machine screws Six M2 mm (0.079 in.) thread nuts Two cable clamps Case Connector Two lock-screws Note: The screws, nuts, cable clamps, and lockscrews are attached to the cover. ■ PART NUMBER FCN-360C064-F Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 25 FCN-360 Series COVER (RIGHT ANGLE CABLE-OUT COVER) (TYPE G1) ■ DIMENSIONS 20 (0.787) 19 (0.748) 6 (0.236) 20 (0.787) F 17 (0.669) ø9 (0.354) 10 (0.393) 81.48 (3.207) 17 (0.669) 14.65 (0.576) Unit: mm (in.) ■ EXPLODED VIEW Case Connector Two cable clamps Slider Case Two M2.6 mm (0.102 in.) thread × 8 mm (0.315 in.) long pan head machine screws 6 (0.236) ■ LOCKED STATE ■ METAL FITTINGS Metal fittings FCN-360A11 F PC board Note: After connectors are mated, moving the slider locks the connectors. 1 mm (0.039 in.) min. Note: The FCN-360 A11-metalfittings are used for this cover. ■ PART NUMBER FCN-360C040-G1 Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 26 FCN-360 Series COVER (RIGHT ANGLE CABLEOUT COVER) (TYPE H/E) ■ DIMENSIONS Material: Zync die cast Plating: Nickel plating 63.98 (2.518) 43.98 (1.731) M2.5 (0.098) × 8 (0.314) 1 (0.039) 17 (0.669) 1 (0.039) φ11 (0.433) Cable hole 19 (0.748) 12 (0.472) 1 (0.039) F 72.48 (2.853) 46 (1.811) M2.5 (0.039) Through-hole 10 (0.393) Unit: mm (in.) ■ EXPLODED VIEW Two M2.5 mm (0.098 in.) thread × 5 mm (0.197 in.) long pan head machine screws Two M2.5 mm (0.098 in.) thread × 8 mm (0.315 in.) long pan head machine screws Case Connector Cable clamp Two lock-screws Note: The screws, cable clamp, and lock-screws are attached to the cover. ■ PART NUMBER FCN-360C040-H/E Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 27 FCN-360 Series COVER (OBTUSE ANGLE CABLE-OUT COVER (40 CONTACTS ONLY)) (TYPE J1) ■ DIMENSIONS φ12 (0.472) M2.6 (0.102) × 25 (0.984) Cable hole Two screws 63.98 (2.518) 20 (0.787) 24 (0.944) Three screws F 71.73 (2.824) 10.3 (0.405) 7 1 (0.039) 46 (1.811) M2 (0.078) × 14 (0.511) Unit: mm (in.) ■ EXPLODED VIEW Three M2 mm (0.079 in.) thread × 14 mm (0.551 in.) long screws Two M2.6 mm (0.102 in.) thread × 25 mm (0.984 in.) long screws Case Two M2.6 mm (0.102 in.) thread × 12 mm (0.472 in.) long screws Connector Cable clamp Case Two M2.6 mm (0.102 in.) thread nuts Three M2 mm (0.079 in.) thread nuts ■ PART NUMBER FCN-360C040-J1 Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 28 FCN-360 Series LOW PROFILE COVER (OBTUSE ANGLE CABLE -OUT) (TYPE J2) ■ DIMENSION 0 8.7 Part number: FCN-360C024-J2 (24 contacts) 17.9 M2.6 mm (0.102 in.) thread machine screw with washer Part number: FCN-360C040-J2 (40 contacts) X) MA ) 6 ( (MIN 5 12 51.41 (2.024) 20° M2 (0.078) View from B M2.6 mm machine screw with washer 22 12.75 25 R4 View from B B M2 (0.078) 46 (1.811) B 24 (0.944) 30˚ 9.5 (0.374) 29.66 (1.167) M2 (0.078) F 1 (0.039) 1 (0.039) 24 (0.944) 46 (1.811) M2 (0.078) 10.3 (0.405) 63.98 71.73 F 10.3 (0.405) 43.66 (1.718) Unit: mm (in.) ■ EXPLODED VIEW Three M2 mm (0.079 in.) thread × 8 mm (0.315 in.) long screws Two M2.6 mm (0.102 in.) thread × 25 mm (0.984 in.) long screws Case Two M2.6 mm (0.102 in.) thread × 6 mm (0.236 in.) long screws Connector Cable clamp Case Two M2.6 mm (0.102 in.) thread nuts Three M2 mm (0.079 in.) thread nuts ■ PART NUMBER FCN-360C024-J2 FCN-360C040-J2 Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 29 FCN-360 Series ACCESSORIES ■ MOUNTING SYLE [Straight mounting metal fitting] [Right-angle mounting metal fitting] Jack with cover Metal fitting [Straight mounting round metal fitting] Plug or jack Plug Jack with cover or plug with cover Jack with cover or plug with cover PCB Metal fitting Plug or jack PCB Metal fitting M2.6 × 8 PCB M2.6 × 10 Note: The M2.6 mm (0.102 in.) thread × 8 mm (0.315 in.) long machine screw shall be separately prepared. M2.6 × 8 Note: The M2.6 mm (0.102 in.) thread × 10 mm (0.394 in.) long machine screw shall be separately prepared. Note: The M2.6 mm (0.102 in.) thread × 8 mm (0.315 in.) long machine screw shall be separately prepared. ■ SELECTION OF METAL FITTINGS ACCORDING TO COMBINATION OF CONNECTORS AND COVERS Jack Cover mounting side 361J Plug 363J 367J — FCN-360A5 — FCN-360A6 364P FCN-360A4 FCN-360A5 FCN-360A4 FCN-360A5 FCN-360A4 FCN-360A5 FCN-360A4 FCN-360A5 Metal FCN-360A1 FCN-360A6 FCN-360A1 FCN-360A6 FCN-360A1 FCN-360A6 FCN-360A1 FCN-360A6 fitting part number FCN-360A1 FCN-360A6 FCN-360A1 FCN-360A6 FCN-360A1 FCN-360A6 FCN-360A1 FCN-360A6 — FCN-360A6 365P FCN-360A2 FCN-360A3 FCN-360A2 FCN-360A3 FCN-360A2 FCN-360A3 FCN-360A2 FCN-360A3 — FCN-360A3 362P Plug Cover mounting side 361P Jack Metal fitting mounting side 364J With cover Without cover With cover Without cover With cover Without cover With cover Without cover With cover Without cover 361P Metal fitting mounting side 362J 361P 364P With cover Without cover With cover Without cover With cover Without cover 361J FCN-360A4 FCN-360A5 — FCN-360A7 — FCN-360A7 362J FCN-360A4 FCN-360A5 — FCN-360A7 — FCN-360A7 363J FCN-360A4 FCN-360A5 — FCN-360A7 — FCN-360A7 FCN-360A4 FCN-360A5 — FCN-360A7 — FCN-360A7 365J FCN-360A10 (FCN-360A8) FCN-360A9 — FCN-360A9 — FCN-360A9 367J FCN-360A4 FCN-360A5 — FCN-360A7 — FCN-360A7 364J Metal fitting part number Note: When the jack or plug without a cover (shaded part) is used, have M2.6 × 8 mm machine screws ready inorder to tighten the connector. Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 30 FCN-360 Series ■ SHAPES AND DIMENSIONS OF METAL FITTINGS 1.Straight Mounting Metal Fittings Part number Shape FCN-360A1 FCN-360A6 5.3 (0.208) 6.3 (0.248) FCN-360A2 FCN-360A3 B 3 (0.118) 4 (0.157) C 9 (0.354) 10 (0.393) FCN-360A8 FCN-360A9 B 5.3 (0.208) 6.3 (0.248) C 13.3 (0.523) 14.3 (0.526) Symbol 8.25 (0.326) M2.6 (0.102) A 5.5 (0.216) A Unit: mm (in.) 2.Right-angle Mounting Metal Fittings Part number Shape Symbol 4 (0.157) 7 (0.275) M2.6 (0.102) B C 5.5 (0.216) Unit: mm (in.) Part number Shape Symbol 4 (0.157) 7.5 (0.295) M2.6 (0.102) B C 5.4 (0.212) Unit: mm (in.) Part number Part number FCN-360A10 Symbol FCN-360A11 Symbol 1 (0.039) 8.1 (0.318) 7.5 (0.295) 4 (0.157) M2.6 (0.102) 1 6 (0.039) (0.236) 3 (0.118) M2.6 (0.102) 7 (0.275) 4 (0.157) 4.6 (0.181) 5.5 (0.216) M2.6 (0.102) 5.5 (0.216) 5.3 (0.208) Unit: mm (in.) Unit: mm (in.) 3.Straight Mounting Round Metal Fittings Part number Shape Symbol FCN-360A4 FCN-360A5 FCN-360A7 7.1(0.279) 9.9 (0.389) 8.1 (0.318) 6 (0.236) M2.6 (0.102) D D 5.25 (0.206) Unit: mm (in.) Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 31 FCN-360 Series Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: www.fceu.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: www.fcai.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 375-8560 Fax: (65) 273-3021 Email: [email protected] www.fcal.fujitsu.com © 2001 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 09/2001 Specifications subject to change Dimensions are in millimeters (inches) www.fujitsu.takamisawa.com 32