USB0403C 8700 E. Thomas Road Scottsdale, AZ 85251 Tel: (480) 941-6300 Fax: (480) 947-1503 thru USB0424C TVSarray ™ Series DESCRIPTION (300 watt) This 4 pin 1 line bidirectional ULTRA LOW CAPACITANCE array is designed for use in applications requiring board level protection from voltage transients caused by electrostatic discharge (ESD) as defined by IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4 and effects of secondary lightning. These arrays are used to protect 1 discrete line utilizing pins (1,4 and 2,3). The S0T-143 product provides board level protection from static electricity and other induced voltage surges that can damage sensitive circuitry. These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays protect 3.3 Volt components such as DRAM’s, SRAM’s, CMOS, HCMOS, HSIC, and low voltage interfaces up to 24Volts. FEATURES MECHANICAL • • • • • • • • Protects 3.3 up through 24V Components Protects 1 line bidirectional Provides electrically isolated protection SOT-143 Packaging ULTRA LOW CAPACITANCE 5 pF • MAXIMUM RATINGS • • • • Molded SOT-143 Surface Mount Weight: .035 grams (approximate) Body Marked with device marking code Pin #1 defined by DOT on top of package PACKAGING 0 • • 0 Operating Temperatures: -55 C to +150 C 0 0 Storage Temperature: -55 C to +150 C Peak Pulse Power: 300 Watts (8/20 µsec, Figure 1) Pulse Repetition Rate: <.01% Tape & Reel EIA Standard 481-1-A 13 inch reel 10,000 pieces 0 ELECTRICAL CHARACTERISTICS @ 25 C Unless otherwise specified PART NUMBER DEVICE MARKING STAND OFF VOLTAG E VWM VOLTS CLAMPING VOLTAGE VC @ 1 Amp (FIGURE 2) VOLTS µA pF mV/°C MAX MIN MAX MAX MAX MAX MAX -5 VOLTS BREAKDOWN VOLTAGE VBR @1 mA CLAMPING VOLTAGE VC @ 5 Amp (FIGURE 2) VOLTS STAND OFF CURRENT ID @ VWM CAPACITANCE (f=1 MHz) @0V C TEMPERATURE COEFFICIENT OF VBR áVBR USB0403C U3 3.3 4 8 11 200 5 USB0405C U5 5.0 6.0 10.8 13 100 5 3 USB0412C U12 12.0 13.3 19 26 1 5 10 USB0415C U15 15.0 16.7 25 32 1 5 13 USB0424C U24 24.0 26.7 44 57 1 5 30 NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off Voltage VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected. MSC0987.PDF ISO 9001 CERTIFIED REV D 1/14/2000 USB0403C thru USB0424C Ipp -- Peak Pulse Current -- % Ipp WAVE FORMS 100 Peak Value -- Ipp 8 X 20 Waveform 50 Half-Value -- Ipp 2 0 0 20 10 30 t td t -- Time in microsec FIGURE 1 Peak Pulse Power Vs Pulse Time FIGURE 2 Pulse Wave Form MOUNTING PAD SOT 143 CIRCUIT DIAGRAM A DIMENSIONS INCHES MM MIN MA MIN MA X X .032 .040 0.80 1.00 A1 .040 .048 1.00 1.20 B --- .057 --- 1.44 C --- .087 --- 2.20 DIM D E .075 BSC .067 BSC 1.90 BSC 1.70 BSC G .032 .040 0.80 1.00 H .134 .140 3.40 3.60 DIMENSION MSC0987.PDF INCHES MIN MILLIMETERS MAX MIN MAX A 0.070 0.080 1.78 2.03 1.40 B 0.047 0.055 1.20 C 0.030 0.037 0.77 0.94 C1 0.015 0.020 0.37 0.50 D 0.110 0.119 2.80 3.04 E 0.035 0.044 0.89 1.17 F 0.071 0.079 1.80 2.00 G 0.0006 0.006 0.013 0.05 H 0.003 0.007 0.085 0.17 I 0.018 0.023 0.45 0.60 J 0.083 0.093 2.10 2.50 ISO 9001 CERTIFIED REV D 1/14/2000