USF1010F-USF1060F Super Fast Rectifiers VOLTAGE RANGE: 100 --- 600 V CURRENT: 10 A ITO-220AC Features Low cost Diffusde junction Low forward voltage drop 4.5± 0.2 10.2± 0.2 2 13.5± 0.5 4.0± 0.3 Mechanical Data φ 3 .2± 0.2 PIN 1 φ 3.3± 0.1 Easily cleaned with alcohol,Isopropanol and similar solvents The plastic material carries U/L recognition 94V-0 8.2± 0.2 High current capability 16.5± 0.3 15.2± 0.5 3.1+0.2 -0.1 2.6± 0.2 1.4± 0.1 0.6± 0.1 0.6± 0.1 5.0± 0.1 Case:JEDEC ITO-220AC,molded plastic Polarity: As marked Weight:0.056 ounces,1.587 gram Mounting position: Any Dimensions in millimeters MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified. Single phase,half wave,60 Hz,resistive or inductive load. For capacitive load,derate by 20%. USF 1010F USF 1020F USF 1030F USF 1040F USF 1050F USF UNITS 1060F Maximum recurrent peak reverse voltage VRRM 100 200 300 400 500 600 V Maximum RMS voltage VRMS 70 140 210 280 350 420 V Maximum DC blocking voltage VDC 100 200 300 400 500 600 V Maximum average forw ard rectified current @TC=100 IF(AV) 10 A IFSM 150 A Peak forw ard surge current 8.3ms single half-sine-w ave superimposed on rated load @TJ=125 Maximum instantaneous forw ard voltage @ 10A Maximum reverse current @TA=25 at rated DC blocking voltage @TA=100 VF 0.98 1.3 10 IR trr Typical junction capacitance (Note2) CJ Typical thermal resistance (Note3) RθJA 3.0 TJ - 55 ----- + 150 TSTG - 55 ----- + 150 Storage temperature range ns 25 (Note1) 70 50 NOTE: 1. Measured with I F=0.5A, I R=1A, I rr=0.25A. 2. Measured at 1.0MHZ and applied rev erse v oltage of 4.0V DC. 3. Thermal resistance f rom junction to ambient. http://www.luguang.cn V A 400 Maximum reverse recovery time Operating junction temperature range 1.7 mail:[email protected] pF /W USF1010F-USF1060F Super Fast Rectifiers Ratings AND Charactieristic Curves FIG.1 -- TEST CIRCUIT DIAGRAM AND REV ERSE RECOVERY TIM E CHARACTERISTIC trr 10 N 1. 50 N 1. + 0 .5 A D.U.T. 0 PULSE GENERATOR (NOTE2) (+) 25VDC (approx) (-) -0 .2 5 A OSCILLOSCOPE (NOTE 1) 1 NONINDUCTIVE -1 .0 A 1 c m N OTES:1 .R ISE TIME = 7n s MAX.IN PU T IMPED AN C E = 1M .2 2p F. JJJJJ2.R ISE TIME =10 ns MAX.SOU R C E IMPED AN C E=5 0 . SE T TIM E BA SE FOR 10 ns/cm 0.1 0.01 .4 12 Single Phase Half Wave 60HZ Resistive or Inductive Load 10 AMPERES 1 FIG.3 -- FORW ARD DERATING CURVE AVERAGE FORWARD CURRENT 10 US F1 03 0F ~U US SF F1 10 05 40 0F F ~U SF 10 60 F US F1 01 0F ~U SF 10 20 F 100 AMPERES INSTANTANEOUS FORWARD CURRENT FIG.2 -- TYPICAL FORW ARD CHARACTERISTIC 8.0 6.0 4.0 2.0 0 0 25 .6 .8 1.0 1.2 1.4 1.6 100 125 150 175 1.8 C A S E TE M P ERA TURE, FIG.5 -- PEAK FORW ARD SURGE CURRENT 200 100 USF1010F - USF1020F 60 40 20 10 USF1030F- USF1060F 6 4 TJ=25 2 0.4 1 2 4 10 20 40 100 REV ERS E V OLTA GE ,VOLTS http://www.luguang.cn 175 150 AMPERES PEAK FORWARD SURGE CURRENT FIG.4 -- TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE,pF 75 Tj=25oC Pulse Width=300 s 1% Duty Cycle INSTA NTANE OUS FORW ARD VOLTAGE , VOLTS 1 0.1 0.2 50 8.3ms Single Half Sine-Wave 125 100 75 50 25 0 1 5 10 50 100 NUM B ER OF CYCLES AT 60Hz mail:[email protected] z