MARL NSPL515DS

Nichia STS-DA1-0167A
<Cat.No.080926>
SPECIFICATIONS FOR NICHIA WARM WHITE LED
MODEL : NSPL515DS
NICHIA CORPORATION
Nichia STS-DA1-0167A
<Cat.No.080926>
1.SPECIFICATIONS
(1) Absolute Maximum Ratings
Item
Forward Current
Pulse Forward Current
Reverse Voltage
Power Dissipation
Operating Temperature
Storage Temperature
Soldering Temperature
Symbol
IF
IFP
VR
PD
Topr
Tstg
Tsld
Absolute Maximum Rating
30
100
5
105
-30 ~ + 85
-40 ~ +100
265°C for 10sec.
(Ta=25°C)
Unit
mA
mA
V
mW
°C
°C
IFP Conditions : Pulse Width ≤ 10msec. and Duty ≤ 1/10
(2) Initial Electrical/Optical Characteristics
Item
Symbol
Forward Voltage
VF
Reverse Current
IR
Luminous Intensity
Iv
x
Chromaticity Coordinate½
y
-
Condition
IF=20[mA]
VR= 5[V]
IF=20[mA]
IF=20[mA]
IF=20[mA]
Typ.
(3.2)
(1.9)
0.41
0.39
(Ta=25°C)
Max.
Unit
3.5
V
50
µA
cd
-
½ Please refer to CIE 1931 chromaticity diagram.
(3) Ranking
Item
Luminous Intensity
Rank W
Rank V
Rank U
Rank T
Symbol
Iv
Iv
Iv
Iv
Condition
IF=20[mA]
IF=20[mA]
IF=20[mA]
IF=20[mA]
Min.
2.32
1.61
1.16
0.80
½ Luminous Intensity Measurement allowance is ± 10%.
Color Ranks
x
y
x
y
x
y
x
y
0.3575
0.3612
0.3545
0.3408
0.3897
0.3823
0.3822
0.3580
(IF=20mA,Ta=25°C)
0.3610
0.3850
Rank d1
0.3780 0.3988
0.3970 0.4116
0.3897
0.3823
0.3720
0.3714
0.3575
0.3612
Rank d2
0.3720 0.3897
0.3714 0.3823
0.3822
0.3580
0.3667
0.3484
0.3988
0.4116
Rank e1
0.4162 0.4390
0.4200 0.4310
0.4255
0.4000
0.4053
0.3907
0.3897
0.3823
Rank e2
0.4053 0.4255
0.3907 0.4000
0.4129
0.3725
0.3954
0.3642
-1-
(Ta=25°C)
Max.
Unit
3.22
cd
2.32
cd
1.61
cd
1.16
cd
Nichia STS-DA1-0167A
<Cat.No.080926>
x
y
x
Y
0.4255
0.4000
Rank f3
0.4390 0.4680
0.4310 0.4385
0.4129
0.3725
Rank f5
0.4255 0.4519
0.4000 0.4086
0.4519
0.4086
x
y
0.4355
0.3785
x
y
0.4519
0.4086
Rank f4
0.4680 0.4970
0.4385 0.4466
0.4770
0.4137
0.4355
0.3785
Rank f6
0.4519 0.4770
0.4086 0.4137
0.4588
0.3838
½ Color Coordinates Measurement allowance is ± 0.01.
½ Basically, a shipment shall consist of the LEDs of a combination of the above ranks.
The percentage of each rank in the shipment shall be determined by Nichia.
Correspondence table of Color Coordinates – Luminous Intensity ranks
Ranking by Luminous Intensity
Ranking by Color Coordinates
T
U
V
W
d1, d2, e1, e2
f3, f4, f5, f6
½ Shaded ranks are available.
2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS
Please refer to “CHARACTERISTICS” on the following pages.
3.OUTLINE DIMENSIONS AND MATERIALS
Please refer to “OUTLINE DIMENSIONS” on the following page.
Material as follows ;
Resin
: Epoxy Resin (over Phosphor)
Lens Color : Milky (Diffusion type)
Leadframe : Ag plating Copper Alloy
4.PACKAGING
· The LEDs are packed in cardboard boxes after packaging in anti-electrostatic bags.
Please refer to “PACKING” on the following pages.
The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity
· In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation.
· The LEDs may be damaged if the boxes are dropped or receive a strong impact against them,
so precautions must be taken to prevent any damage.
· The boxes are not water resistant and therefore must be kept away from water and moisture.
· When the LEDs are transported, we recommend that you use the same packing method as Nichia.
-2-
Nichia STS-DA1-0167A
<Cat.No.080926>
5.LOT NUMBER
The first six digits number shows lot number.
The lot number is composed of the following characters;
-U
- Year
( 7 for 2007, 8 for 2008 )
- Month ( 1 for Jan., 9 for Sep., A for Oct.,
- Nichia's Product Number
U - Ranking by Color Coordinates
- Ranking by Luminous Intensity
-3-
B for Nov. )
Nichia STS-DA1-0167A
<Cat.No.080926>
6.RELIABILITY
(1) TEST ITEMS AND RESULTS
Test Item
Standard
Test Method
Test Conditions
Note
Number of
Damaged
1 time
0/50
1 time
over 95%
0/50
Resistance to
Soldering Heat
JEITA ED-4701
300 302
Tsld=260 ± 5°C, 10sec.
3mm from the base of the epoxy bulb
Solderability
JEITA ED-4701
300 303
Tsld=235 ± 5°C,
(using flux)
Temperature Cycle
JEITA ED-4701
100 105
-40°C ~ 25°C ~ 100°C ~ 25°C
30min. 5min. 30min. 5min.
100 cycles
0/50
Moisture Resistance Cyclic
JEITA ED-4701
200 203
25°C ~ 65°C ~ -10°C
90%RH 24hrs./1cycle
10 cycles
0/50
Terminal Strength
(bending test)
JEITA ED-4701
400 401
Load 5N (0.5kgf)
0° ~ 90° ~ 0° bend 2 times
No noticeable
damage
0/50
Terminal Strength
(pull test)
JEITA ED-4701
400 401
Load 10N (1kgf)
10 ± 1 sec.
No noticeable
damage
0/50
High Temperature Storage
JEITA ED-4701
200 201
Ta=100°C
1000hrs.
0/50
Temperature Humidity
Storage
JEITA ED-4701
100 103
Ta=60°C, RH=90%
1000hrs.
0/50
Low Temperature Storage
JEITA ED-4701
200 202
Ta=-40°C
1000hrs.
0/50
Steady State Operating Life
Ta=25°C, IF=30mA
1000hrs.
0/50
Steady State Operating Life
of High Humidity Heat
60°C, RH=90%, IF=20mA
500hrs.
0/50
Steady State Operating Life
of Low Temperature
Ta=-30°C, IF=20mA
1000hrs.
0/50
5sec.
(2) CRITERIA FOR JUDGING DAMAGE
Criteria for Judgement
Min.
Max.
Item
Symbol Test Conditions
Forward Voltage
VF
IF=20mA
U.S.L.*)
Reverse Current
IR
VR=5V
U.S.L.*)
Luminous Intensity
IV
IF=20mA
L.S.L.**) 0.7
*) U.S.L. : Upper Standard Level
**) L.S.L. : Lower Standard Level
-4-
1.1
2.0
Nichia STS-DA1-0167A
<Cat.No.080926>
7.CAUTIONS
The LEDs are devices which are materialized by combining Blue LEDs and special phosphors.
Consequently, the color of the LEDs is changed a little by an operating current.
Care should be taken after due consideration when using LEDs.
(1) Lead Forming
· When forming leads, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.
Do not use the base of the leadframe as a fulcrum during lead forming.
· Lead forming should be done before soldering.
· Do not apply any bending stress to the base of the lead. The stress to the base may damage the LED’s
characteristics or it may break the LEDs.
· When mounting the LEDs onto a printed circuit board, the holes on the circuit board should be exactly
aligned with the leads of the LEDs. If the LEDs are mounted with stress at the leads, it causes
deterioration of the epoxy resin and this will degrade the LEDs.
(2) Storage
· The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Nichia and
the storage life limits are 3 months.
If the LEDs are stored for 3 months or more, they can be stored
for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material.
· Nichia LED leadframes are silver plated copper alloy. The silver surface may be affected by
environments which contain corrosive substances. Please avoid conditions which may cause the LED
to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering
operations. It is recommended that the LEDs be used as soon as possible.
· Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where
condensation can occur.
(3) Recommended circuit
· In designing a circuit, the current through each LED must not exceed the absolute maximum rating
specified for each LED. It is recommended to use Circuit B which regulates the current flowing
through each LED. In the meanwhile, when driving LEDs with a constant voltage in Circuit A, the
current through the LEDs may vary due to the variation in forward voltage (VF) of the LEDs. In the
worst case, some LED may be subjected to stresses in excess of the absolute maximum rating.
(B)
(A)
...
...
· This product should be operated in forward bias. A driving circuit must be designed so that the product
is not subjected to either forward or reverse voltage while it is off. In particular, if a reverse voltage is
continuously applied to the product, such operation can cause migration resulting in LED damage.
-5-
Nichia STS-DA1-0167A
<Cat.No.080926>
(4) Static Electricity
· Static electricity or surge voltage damages the LEDs.
It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.
· All devices, equipment and machinery must be properly grounded. It is recommended that precautions
be taken against surge voltage to the equipment that mounts the LEDs.
· When inspecting the final products in which LEDs were assembled, it is recommended to check
whether the assembled LEDs are damaged by static electricity or not.
It is easy to find
static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended).
· Damaged LEDs will show some unusual characteristics such as the leak current remarkably
increases, the forward voltage becomes lower, or the LEDs do not light at the low current.
Criteria : (VF > 2.0V at IF=0.5mA)
(5) Soldering Conditions
· Nichia LED leadframes are silver plated copper alloy.
This substance has a low
thermal coefficient (easily conducts heat).
Careful attention should be paid during soldering.
· Solder the LED no closer than 3mm from the base of the epoxy bulb.
Soldering beyond the base
of the tie bar is recommended.
· Recommended soldering conditions
Dip Soldering
Hand Soldering
Pre-Heat
120°C Max.
Temperature
350°C Max.
Pre-Heat Time
60 seconds Max.
Soldering Time
3 seconds Max.
Solder Bath
260°C Max.
Position
No closer than 3 mm from the
base of the epoxy bulb.
Temperature
Dipping Time
10 seconds Max.
Dipping Position
No lower than 3 mm from the
base of the epoxy bulb.
· Although the recommended soldering conditions are specified in the above table, dip or hand
soldering at the lowest possible temperature is desirable for the LEDs.
· A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.
· Dip soldering should not be done more than one time.
· Hand soldering should not be done more than one time.
· Do not apply any stress to the lead particularly when heated.
· The LEDs must not be repositioned after soldering.
· After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until
the LEDs return to room temperature.
· Direct soldering onto a PC board should be avoided.
Mechanical stress to the resin may be caused
from warping of the PC board or from the clinching and cutting of the leadframes.
When it is
absolutely necessary, the LEDs may be mounted in this fashion but the User will assume responsibility
for any problems.
Direct soldering should only be done after testing has confirmed that no damage,
such as wire bond failure or resin deterioration, will occur.
Nichia’s LEDs should not be soldered
directly to double sided PC boards because the heat will deteriorate the epoxy resin.
· When it is necessary to clamp the LEDs to prevent soldering failure, it is important to minimize
the mechanical stress on the LEDs.
· Cut the LED leadframes at room temperature.
Cutting the leadframes at high temperatures may
cause failure of the LEDs.
-6-
Nichia STS-DA1-0167A
<Cat.No.080926>
(6) Heat Generation
· Thermal design of the end product is of paramount importance.
Please consider the heat generation
of the LED when making the system design. The coefficient of temperature increase per input
electric power is affected by the thermal resistance of the circuit board and density of LED
placement on the board, as well as other components. It is necessary to avoid intense heat generation
and operate within the maximum ratings given in this specification.
· The operating current should be decided after considering the ambient maximum temperature of LEDs.
(7) Cleaning
· It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using
other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not.
Freon solvents should not be used to clean the LEDs because of worldwide regulations.
· Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic
cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition.
Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur.
(8) Safety Guideline for Human Eyes
· The International Electrical Commission (IEC) published in 2006 IEC 62471:2006 Photobiological
safety of lamps and lamp systems which includes LEDs within its scope. Meanwhile LEDs were
removed from the scope of the IEC 60825-1:2007 laser safety standard, the 2001 edition of which
included LED sources within its scope. However, keep in mind that some countries and regions have
adopted standards based on the IEC laser safety standard IEC 60825-1:2001 which includes LEDs
within its scope.
Following IEC 62471:2006, most of Nichia LEDs can be classified as belonging to either Exempt
Group or Risk Group 1. Optical characteristics of a LED such as output power, spectrum and light
distribution are factors that affect the risk group determination of the LED. Especially a high-power
LED, that emits light containing blue wavelengths, may be in Risk Group 2.
Great care should be taken when viewing directly the LED driven at high current or the LED with
optical instruments, which may greatly increase the hazard to your eyes.
-7-
Nichia STS-DA1-0167A
<Cat.No.080926>
(9) Others
· NSPL515DS complies with RoHS Directive.
· Care must be taken to ensure that the reverse voltage will not exceed the absolute maximum rating
when using the LEDs with matrix drive.
· Flashing lights have been known to cause discomfort in people; you can prevent this by taking
precautions during use.
Also, people should be cautious when using equipment that has had LEDs
incorporated into it.
· The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such
as office equipment, communications equipment, measurement instruments and household appliances).
Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality
and reliability are required, particularly when the failure or malfunction of the LEDs may directly
jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor
control systems, automobiles, traffic control equipment, life support systems and safety devices).
· User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written
consent from Nichia.
When defective LEDs are found, the User shall inform Nichia directly before
disassembling or analysis.
· The formal specifications must be exchanged and signed by both parties before large volume purchase begins.
· The appearance and specifications of the product may be modified for improvement without notice.
-8-
Nichia STS-DA1-0167A
<Cat.No.080926>
ICI Chromaticity Diagram
0.9
520
530
0.8
540
510
550
0.7
560
0.6
570
500
0.5
580
y
e1
f3 f4
590
d1
0.4
d2
e2
600
f5 f6
610
620
0.3 490
630
0.2
480
0.1
470
460
0
0
0.1
0.2
0.3
0.4
x
Color Coordinates Measurement allowance is ± 0.01.
-9-
0.5
0.6
0.7
0.8
50
20
10
5
3
2
1
0
0
20 40 60 80 100 120
Forward Current IFP (mA)
Ambient Temperature vs.
Forward Voltage
Ambient Temperature vs.
Relative Luminosity
5.0
2.0
4.6
4.2
IFP=60mA
IFP=20mA
IFP=5mA
3.8
3.4
3.0
2.6
2.2
-40 -20 0 20 40 60 80 100
Ambient Temperature Ta (°C)
Relative Luminosity (a.u.)
-10-
Forward Voltage VF (V)
1
2.0 2.5 3.0 3.5 4.0 4.5 5.0
Forward Voltage VF (V)
Ta=25°C
4
IFP=20mA
1.0
0.5
0.2
-40 -20 0 20 40 60 80 100
Ambient Temperature Ta (°C)
Allowable Forward Current IFP (mA)
Relative Luminosity (a.u.)
Forward Current IFP (mA)
Ta=25°C
200
Ta=25°C
100
50
30
20
10
1
5 10 20
50 100
Duty Ratio (%)
Ambient Temperature vs.
Allowable Forward Current
Allowable Forward Current IF (mA)
5
200
100
Duty Ratio vs.
Allowable Forward Current
Forward Current vs.
Relative Luminosity
Forward Voltage vs.
Forward Current
40
30
20
10
8.5
0
0
20
40
60
80 100
Ambient Temperature Ta (°C)
NICHIA CORPORATION
NSPLxxxx
Title
CHARACTERISTICS
No.
080326813061
Nichia STS-DA1-0167A
<Cat.No.080926>
Model
Forward Current vs.
Chromaticity Coordinate
Spectrum
Relative Emission Intensity (a.u.)
0.41
Ta=25°C
0.40
y
100mA
30mA
20mA
5mA
1mA
0.39
0.38
0.37
0.38
0.39
0.40
0.41
0.42
x
Ambient Temperature vs.
Chromaticity Coordinate
0.8
0.6
0.4
0.2
0
400
500
600
700
Wavelength λ (nm)
Relative Luminosity (a.u.)
-11-
-30°C
0.40
0°C
25°C
0.39
50°C
85°C
0.38
0.39
0.40
0.41
800
0°
1.0
IFP=20mA
y
Ta=25°C
IF=20mA
1.0
Directivity
0.41
0.37
0.38
1.2
0.42
10° 20°
30°
Ta=25°C
IFP=20mA
40°
50°
60°
0.5
70°
80°
0
90°
x
60°
30°
Radiation Angle
0°
90°
1.0
0.5
Rev.2
Section
Approve Check
Draw
ST
Rev.3
Date
Sep. 18, 2008
Rev.4
Model
NSPL515D(S)
NICHIA CORPORATION
Title
CHARACTERISTICS
No.
STSZ-H813122
Nichia STS-DA1-0167A
<Cat.No.080926>
Rev.1
1.5MAX.
φ 5.6
7.3
Stopper
0.3
1
5.3
φ5
1.1
(2.5)
Cathode
… 0.5 ± 0.05
Anode
8.3
-12-
12.1 ± 0.5
28.6 ± 1
0.3
(2)
ITEM
RESIN
LENS COLOR
LEAD FRAME
1
MATERIALS
Epoxy Resin (over Phosphor)
Milky (Diffusion type)
Ag Plating Copper Alloy
Model
NICHIA CORPORATION
Title
No.
NSPL515DS
OUTLINE DIMENSIONS
080307811281
Nichia STS-DA1-0167A
<Cat.No.080926>
Remark:
Please note that the bare copper alloy showing at the cut end
of the lead frame may be corroded under certain conditions.
LEDs have some sharp edges and points, particularly lead
frames. Please handle with care so as to avoid injuries.
Unit
mm
3/1
Scale
Allow
±0.2
Nichia STS-DA1-0167A
<Cat.No.080926>
Print
N ICHIA
Cardboard
XXXX LED
Anti-electrostatic bag
TYPE
NxPxxxxxx
LOT
QTY
xxxxxx-U„
pcs
RoHS
NICHIA CORPORATION
491OKA,KAMINAKA,ANAN,TOKUSHIMA,JAPAN
CAUTION TO
ELECTROSTATIC DAMAGE
The quantity is printed on this bag.
静電気に注意
Label
NICHIA
XXXX LED
Cardboard
TYPE
LOT
QTY
NxPxxxxxx
xxxxxx-U„
PCS
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Cardboard box
360¯135¯215¯4t
½ One box contains 8 bags at maximum.
NICHIA CORPORATION
Cardboard
Model
NxPxxxxxx
Title
PACKING
No.
070508659112
Print
NIC HIA
Anti-electrostatic bag
XXXX LED
TYPE
NxPxxxxxx
LOT
QTY
xxxxxx-U„
pcs
RoHS
NICHIA CORPORATION
The quantity is printed on this bag.
491OKA,KAMINAKA,ANAN,TOKUSHIMA,JAPAN
CAUTION TO
ELECTROSTATIC DAMAGE
静電気に注意
Cardboard box A
Label
NICHIA
XXXX LED
TYPE
LOT
QTY
NxPxxxxxx
xxxxxx-U„
PCS
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Cardboard
½ Put this label on the cardboard box B.
Cardboard box B
360¯135¯215¯4t
½ The cardboard box B contains
2 cardboard box A at maximum.
NICHIA CORPORATION
-13-
Model
NxPxxxxxx
Title
PACKING
No.
070508659122
Nichia STS-DA1-0167A
<Cat.No.080926>
Print
Cardboard
NICHIA
Anti-electrostatic bag
XXXX LED
TYPE
NxPxxxxxx
LOT
QTY
xxxxxx-U„
pcs
RoHS
NICHIA CORPORATION
491OKA,KAMINAKA,ANAN,TOKUSHIMA,JAPAN
The quantity is printed on this bag.
CAUTION TO
ELECTROSTATIC DAMAGE
静電気に注意
Label
NICHIA
Cardboard
XXXX LED
TYPE
LOT
QTY
NxPxxxxxx
xxxxxx-U„
PCS
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Cardboard box
425¯135¯355¯4t
½ One box contains 20 bags at maximum.
NICHIA CORPORATION
Model
NxPxxxxxx
Title
PACKING
No.
070508659132
Print
Cardboard
NICH IA
XXXX LED
Anti-electrostatic bag
TYPE
NxPxxxxxx
LOT
QTY
xxxxxx-U„
pcs
RoHS
NICHIA CORPORATION
491OKA,KAMINAKA,ANAN,TOKUSHIMA,JAPAN
The quantity is printed on this bag.
Cardboard box A
CAUTION TO
ELECTROSTATIC DAMAGE
静電気に注意
Label
NICHIA
XXXX LED
TYPE
LOT
QTY
Cardboard
NxPxxxxxx
xxxxxx-U„
PCS
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
½ Put this label on the cardboard box B.
Cardboard box B
425¯135¯355¯4t
NICHIA CORPORATION
Model
NxPxxxxxx
Title
PACKING
No.
070508659142
½ The cardboard box B contains 4 cardboard box A at maximum.
-14-