MICRODC WRD121212YS-2W

WRD
-YS
-1W&WRD
-YS
-2W Series
WRDYSWRDYS1W&2W,WIDE INPUT,ISOLATED&REGULATED Twin Output DC∕DC Converter
SELECTION GUIDE
Input
Output
Voltage(VDC)
Order code
No-load
*
Nominal
Range
Max.
(mA,Typ)
WRD050505YS-1W
5
4.5-9.0
11
40
FEATURES
WRD050909YS-1W
5
4.5-9.0
11
◆RoHS compliant
WRD051212YS-1W
5
4.5-9.0
WRD051515YS-1W
5
4.5-9.0
WRD050505YS-2W
5
WRD050909YS-2W
5
◆2:1 wide input voltage range
WRD051212YS-2W
◆UL 94V-0 package material
WRD051515YS-2W
Current(mA)
Voltage
Efficiency
(% ,Typ)
Max.
Min.
5/5
100/100
10/10
70
40
9/9
55/55
5/5
71
11
40
12/12
42/42
4/4
73
11
40
15/15
33/33
3/3
72
4.5-9.0
11
40
5/5
200/200
20/20
67
4.5-9.0
11
40
9/9
111/111
11/11
71
5
4.5-9.0
11
40
12/12
83/83
8/8
72
5
4.5-9.0
11
40
15/15
67/67
7/7
73
WRD120505YS-1W
12
9.0-18
22
20
5/5
100/100
10/10
73
WRD120909YS-1W
12
9.0-18
22
20
9/9
55/55
5/5
76
◆Industry standard pinout
WRD121212YS-1W
12
9.0-18
22
20
12/12
42/42
4/4
78
◆1KVDC isolation
WRD121515YS-1W
12
9.0-18
22
20
15/15
33/33
3/3
78
WRD120505YS-2W *
12
9.0-18
22
20
5/5
200/200
20/20
75
WRD120909YS-2W *
12
9.0-18
22
20
9/9
111/111
11/11
77
WRD121212YS-2W *
12
9.0-18
22
20
12/12
83/83
8/8
80
WRD121515YS-2W *
12
9.0-18
22
20
15/15
67/67
7/7
79
WRD240505YS-1W
24
18-36
40
10
5/5
100/100
10/10
76
◆Miniature SIP Package
◆Operating temperature: -40℃to+85℃
◆No heatsink required
◆Continuous Short Circuit Protection
◆Internal SMD construction
MODEL SELECTION
①
②
③
④
⑤
⑥
⑦
WRD 05 05 05 Y S -1W
①Product Series
③Output Voltage 1st
⑤Wide Input
⑦Rated Power
②Input Voltage
④Output Voltage 2st
⑥SIP Package
APPLICATIONS
Y S-1W & WRD_
YS-2W series are specially
The WRD_
WRD_Y
WRD_Y
designed for applications where a wide range input
voltage power supplies are isolated from the input
power supply in a distributed power supply system on a
circuit board. These products apply to:
1) Where the voltage of the input power supply is wide
range (voltage range ≤2:1);
2) Where isolation is necessary between input and output
(Isolation Voltage ≤ 1000VDC);
3) Where isolation is necessary between Vout1 and Vout2
(Isolation Voltage ≤ 1000VDC);
(VDC)
WRD240909YS-1W
24
18-36
40
10
9/9
55/55
5/5
77
WRD241212YS-1W *
24
18-36
40
10
12/12
42/42
4/4
78
WRD241515YS-1W
24
18-36
40
10
15/15
33/33
3/3
77
WRD240505YS-2W
24
18-36
40
10
5/5
200/200
20/20
76
WRD240909YS-2W
24
18-36
40
10
9/9
111/111
11/11
78
WRD241212YS-2W *
24
18-36
40
10
12/12
83/83
8/8
80
WRD241515YS-2W *
24
18-36
40
10
15/15
67/67
7/7
79
WRD480505YS-1W
48
36-72
80
5
5/5
100/100
10/10
73
WRD480909YS-1W *
48
36-72
80
5
9/9
55/55
5/5
75
WRD481212YS-1W *
48
36-72
80
5
12/12
42/42
4/4
77
WRD481515YS-1W *
48
36-72
80
5
15/15
33/33
3/3
77
WRD480505YS-2W
48
36-72
80
5
5/5
200/200
20/20
75
WRD480909YS-2W *
48
36-72
80
5
9/9
111/111
11/11
78
WRD481212YS-2W
48
36-72
80
5
12/12
83/83
8/8
79
WRD481515YS-2W *
48
36-72
80
5
15/15
67/67
7/7
78
*Input voltage can’t exceed this value, or will cause the permanent damage.
4) Where the regulation of the output voltage and the
output ripple noise are demanded.
ISOLATION SPECIFICATIONS
Parameter
Isolation test voltage
Isolation resistance
MICRODC reserves the copyright
http://www.microdc.cn
Isolation capacitance
Test conditions
Flash tested for 1 minute and 1mA max(Vin/Vout)
Test at Viso=500VDC(Vin/Vout)
100KHz,1V
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Min.
Typ.
Max.
1000
Unit
VDC
1000
MΩ
80
Page 1 of 3
PF
WRD
-YS
-1W&WRD
-YS
-2W Series
WRDYSWRDYSOUTPUT SPECIFICATIONS
TYPICAL TEMPERATURE CURVE
Parameter
Test conditions
Main output voltage accuracy
Vice output voltage accuracy
Typ.
Max
Unit
Refer to recommended circuit
±1
±3
%
Refer to recommended circuit
±3
±5
%
Load regulation
10% to 100% full load
±0.5
±1 *
%
Line regulat ion
Input voltage from low to high
±0.2
±0.5
%
Temperature drift (Vout)
Refer to recommended circuit
20MHz Bandwidth
50
100% load, input voltage range
300
Ripple & Noise**
Switching frequency
Min
±0.03
%/℃
100
mVp-p
KHz
*Dual output models unbalanced load: ±5%.
** Test ripple and noise by "parallel cable" method. See detailed operation instructions at Testing of Power
Converter section, application notes.
RECOMMENDED CIRCUIT
COMMON SPECIFICATIONS
Parameter
Conditions
Min.
Typ.
Storage humidity range
Operating temperature
Storage temperature
Lead temperature
Max.
Units
95
%
-40
85
-55
125
1.5mm from case for 10 seconds
℃
300
Temp.rise at full load
15
No-load power consumption
0.1
Case material
W
Plastic(UL94-V0)
Short circuit protection
Continuous
Cooling
Free air convection
MTBF
1000
K hours
Weight
5.8
g
APPLICATION NOTE
1) CS Pin
By connecting a
low ESR capacitor between
this
terminal and
the pin-7(Figure
1),
the output
ripple and noise may be further improved. Generally, the capacitance is no greater than 47uF.
2) Requirement on Output Load
To ensure
output
the
this module
load
can
is
not
less
load,
the
output
operate
than
efficiently
10%
of
the
and
full
reliably,
load,
If
sharply.
If
During
the
operation,
actual
load
the minimum
is
less
than
specified
minimum
ripple may
increase
the actual output
power
is very
small,
please
add
other
lower
an
appropriate
output
power
resistor
as
extra
loading,
or
contact
our
company
for
products.
EXTERNAL CAPACITOR TABLE (TABLE 1)
3) Recommended Circuit
Vout
2W :Cout
1W : Cout
(VDC)
(μF)
(μF)
5
680
470
9
470
330
operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1)
12
330
220
Cin:
24
220
100
If you want to
further decrease
the
input/output ripple, you can
increase capacitance properly
or choose capacitors with low ESR (Figure 1).
However, the capacitance of the output filter capacitor must be proper. If the capacitance is too
big, a startup problem might
arise. For every
channel
of
output, provided
the
safe
and
reliable
Lin:
5V & 12V
100μF
24V & 48V
10μF-47μF
10μH-120μH
Cout: 100μF(TYP)
4) Input current
When the environment temperature is higher than 71
71°° C, the product
an 60% of the rated power.
output power should be less th
tha
While using unstable power source, please ensure the output voltage and ripple voltage do not
exceed
indexes
provide
for
of
the
converter.
The
preceding
power
source
must
be
able
to
No parallel connection or plug and play.
converter sufficient starting current Ip (Figure 2). General:
Ip ≤1.4*Iin-max
5) No parallel connection or plug and play
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 3
WRD
-YS
-1W&WRD
-YS
-2W Series
WRDYSWRDYSMECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
TUBE OUTLINE DIMENSIONS
Note:
Uni t:mm[ inch]
Pin sect ion tolerances:±0.10mm[±0.004inch]
General tolerances:±0.25mm[±0.010inch]
FOOTPRINT DETAILS
PIN
FUNCTION
1
GND
2
Vin
6
+V01
7
0V1
8
CS
9
0V2
10
+V02
Note:
Unit :mm[inch]
General tolerances:±0.50mm[±0.020inch]
L=530mm[20.866inch] Tube Quantity: 18pcs
L=220mm[8.661inch]
Tube Quantity: 8pcs
Note:
1. The load shouldn't be less than 10%, otherwise ripple will increase dramatically.
2. Operation under 10% load will not damage the converter; However, they may not meet all specification listed.
3. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
4. In this datasheet, all the test methods of indications are based on corporate standards.
5. Only typical models listed, other models may be different, please contact our technical person for more details.
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
REACH COMPLIANT INFORMATION
E-mail:[email protected]
Website:http://www.microdc.cn
http://www.microdc.cn
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 3 of 3