MICRODC WRA-ZMD-6W

WRA-ZMD-6W&WRB-ZMD-6W Series
6W, 4:1 WIDE INPUT, ISOLATED & REGULATED DUAL & SINGLE OUTPUT DC-DC CONVERTER
SELECTION GUIDE
Input
Order code
Output
Voltage(VDC)
Voltage
(VDC)
Current(mA)
Efficiency
(%,Typ)
Nominal
Range
Max.*
Max.
Min.
WRA2405ZMD-6W
24
9-36
40
±5
±600
±60
80
WRA2412ZMD-6W
24
9-36
40
±12
±250
±25
82
WRA2415ZMD-6W
24
9-36
40
±15
±200
±20
84
WRA2424ZMD-6W
24
9-36
40
±24
±125
±13
82
◆1500VDC isolation
WRB2405ZMD-6W
24
9-36
40
5
1200
120
80
◆Short circuit protection (automatic recovery)
WRB2412ZMD-6W
24
9-36
40
12
500
50
82
WRB2415ZMD-6W
24
9-36
40
15
400
40
84
WRB2424ZMD-6W
24
9-36
40
24
250
25
82
◆Internal SMD construction
WRA4805ZMD-6W
48
18-72
80
±5
±600
±60
80
◆Metal shielding package
WRA4812ZMD-6W
48
18-72
80
±12
±250
±25
82
WRA4815ZMD-6W
48
18-72
80
±15
±200
±20
84
WRB4805ZMD-6W
48
18-72
80
5
1200
120
80
WRB4812ZMD-6W
48
18-72
80
12
500
50
82
WRB4815ZMD-6W
48
18-72
80
15
400
40
84
FEATURES
◆DIP package
◆Operating temperature: -40℃ to +85℃
◆Industry standard pinout
◆No heat sink required
◆MTBF>1,000,000 hours
*Input voltage can't exceed this value, or will cause the permanent damage.
◆RoHS Compliance
MODEL SELECTION
WRA①24②05③Z④ M⑤D⑥-6W⑦
①Product Series
③Output Voltage 1st
⑤Metal Shield
⑦Rated Power
②Input Voltage
④Wide (4:1) Input Range
⑥DIP Package Style
COMMON SPECIFICATIONS
Parameter
Test conditions
Min.
Typ.
Storage humidity
APPLICATIONS
Operating temperature
-40
Storage temperature
-55
Temp. rise at full load
The WRA_ZMD-6W & WRB_ZMD-6W Series are
Lead temperature
specially designed for applications where a wide range
Cooling
input voltage power supplies are isolated from the
Short circuit protection
input power supply in a distributed power supply system
Case material
on a circuit board.
MTBF
1.5mm from case for 10 seconds
Units
95
%
85
℃
125
℃
℃
40
300
℃
Free air convection
Continuous, automatic recovery
Aluminum
1000
Weight
These products apply to:
Max.
K hours
15
g
1) Where the voltage of the input power supply is wide
range (voltage range≤4:1);
2) Where isolation is necessary between input and
output(isolation voltage≤1500VDC);
3) Where the regulation of the output voltage and the
output ripple noise are demanded.
ISOLATION SPECIFICATIONS
Parameter
Test conditions
Min.
Isolation voltage
Tested for 1 minute and 1 mA max
1500
Isolation resistance
Test at 500VDC
1000
Isolation capacitance
Input/Output, 100KHz/1V
Typ.
Max.
VDC
MΩ
100
MICRODC reserves the copyright
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Units
Page 1 of 3
pF
WRA-ZMD-6W&WRB-ZMD-6W Series
OUTPUT SPECIFICATIONS
Parameter
TYPICAL TEMPERATURE CURVE
Test conditions
Min.
Typ.
Max
Units
Output power
See above products program
6
W
Line regulation (at full load)
Input voltage from low to high
0.6
±0.2
±0.5
%
Load regulation
Form 10% to 100%load
±0.5
±2*
%
Positive output voltage accuracy
Refer to recommended circuit
±1
±3
%
Negative output voltage accuracy
Refer to recommended circuit
±3
±5
Temperature Drift (Vout)
Refer to recommended circuit
±0.02
Ripple**
20MHz Bandwidth
30
50
mVp-p
Noise**
20MHz Bandwidth
75
150
mVp-p
Switching frequency
100% load, input voltage range
300
%
%/℃
KHz
* Dual output models unbalanced load: ±5%.
**Test ripple and noise by“parallel cable”method. See detailed operation instructions at Testing of Power
Converter section, application notes.
RECOMMENDED CIRCUIT
APPLICATION NOTE
1) Requirement on output load
In order to ensure the product operate efficiently and reliably, in addition to a max load (namelyull load),
a minimum load is specified for this kind of DC/DC converter. Make sure the specified range of input
voltage is not exceeded, the minimum output load no less than 10% load. If the actual load is less than the
specified minimum load, the output ripple may increase sharply while its efficiency and reliability will
reduce greatly. If the actual output power is very small, please add an appropriate resistor as extra loading,
or
contact our company for other lower output power products.
2) Recommended Circuit
All the WRA_ZMD-6W & WRB_ZMD-6W series have been tested according to the following
recommended testing circuit before leaving factory. This series should be tested under load (see Figure 1).
If you want to further decrease the input/output ripple, you can increase capacitance properly or
choose capacitors with low ESR. However, the capacitance should not be too high, or may cause start-up
problem. For every channel of output, provided the safe and reliable operation is ensured, the greatest
capacitance of its filter capacitor sees (Table 1). General:
Cin:
24V&48V
Cout:
10µF/100mA
10µF~47µF
3) Input current
While using unstable power source, please ensure the output voltage and ripple voltage do not exceed
indexes of the converter. The preceding power source must be able to provide for converter sufficient
starting current Ip (Figure 2).
General: Ip ≤1.4*Iin-max
4) No parallel connection or plug and play
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 3
WRA-ZMD-6W&WRB-ZMD-6W Series
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT(TOP VIEW)
TUBE OUTLINE DIMENSIONS
Note:
1. The load shouldn't be less than 10%, otherwise ripple will increase dramatically.
2.
Operation under 10% load will not damage the converter; However, they may not meet all specification listed.
3.
Capacitor MAX load tested at input voltage range and full load.
4. All specifications measured at Ta=25℃, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
5.
In this datasheet, all the test methods of indications are based on corporate standards.
6.
Only typical models listed, other models may be different, please contact our technical person for more details.
RoHS COMPLIANT INFORMATION
Microdc Professional Power Module,Inc.
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C
Tel:0086-20-86000646 E-mail:[email protected]
for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte
Website:http://www.microdc.cn
Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are
Microdc Professional Power module,Inc.makes no representation that
backward compatible with Sn/Pb soldering systems.
the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or
REACH COMPLIANT INFORMATION
future patent rights. Specifications are subject to change without notice.
This series has proven that this product does not contain harmful chemicals, it also has harmful chemical
©2010
substances through the registration, inspection and approval.
Microdc Professional Power Module, Inc. Guangzhou
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 3 of 3