MP2116 2A, 6V, 100% Duty Cycle Synchronous Step-Down Converter with 0.5A LDO The Future of Analog IC Technology DESCRIPTION FEATURES The MP2116 is an internally compensated 1.25MHz, 2A synchronous step-down switching DC-DC converter plus a standalone low-input voltage, 0.5A low dropout (LDO) linear regulator. It is ideal for powering portable equipment that operates from a single cell Lithium-Ion (Li+) Battery. The MP2116 can provide up to 2A to the switcher output, and 0.5A load current to the LDO output from a 2.5V to 6V input voltage. Both output voltages can be regulated as low as 0.6V. • The 2A Synchronous switcher features integrated high-side and low-side switch for high efficiency and small footprint. With peak current mode control and internal compensation, the MP2116 is stable with ceramic capacitors. Fault condition protection includes cycle-bycycle current limiting and thermal shutdown. The standalone low-input voltage 0.5A LDO is used to power noise sensitive circuitry. The LDO’s separate input supply pin (IN2) can be connected to the switcher output to reduce power dissipation and noise from the main switcher. MP2116 is available in the small 10-pin 3mmx3mm QFN package. • • • • • • • • • • • • • • • 100% Duty Cycle Low Dropout Operation (High-Side PFET) 2A Switcher Output Current at VIN=3V Internal Power MOSFET Switches Stable with Ceramic Capacitors Up to 95% Efficiency for Switcher 1.25MHz Switching Frequency Internal Soft-start for Switcher 2.5V to 6V Input Range, for Switcher 1V to VIN1 Input Range, for LDO 0.5A LDO Output Current 1μA Shutdown Current Thermal Shutdown Cycle-by-Cycle Over Current Protection Short Circuit Protection Power OK Output Available in 10-Pin QFN Package APPLICATIONS • • • • • DVD+/-RW Drives Smart Phones PDAs Digital Cameras Portable Instruments All MPS parts are lead-free and adhere to the RoHS directive. For MPS green status, please visit MPS website under Products, Quality Assurance page. “MPS” and “The Future of Analog IC Technology” are registered trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION Efficiency vs Load Current R5 500kΩ 100 VIN=3.3V OFF ON VIN 2.5V - 6V *OUT1 1.8V @ 1.5A CO1 22μF 3 L 4 6 R1 499kΩ CIN2 R2 2.2μF 249kΩ * IOUT1+IOUT2=2A 1 EN1 IN1 EN2 PWROK SW1 MP2116 OUT2 IN2 FB1 CIN1 10μF FB2 GND POWER OK 9 8 7 10 5 R3 60kΩ R4 60kΩ OUT2 1.2V @ 0.5A CO2 4.7μF EFFICIENCY (%) 90 2 80 VIN=4.0V 70 60 50 VIN=5.0V 40 30 20 10 VOUT=1.8V 0 10 100 1000 10000 LOAD CURRENT (mA) MP2116 Rev.1.0 1/17/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 1 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO ORDERING INFORMATION Part Number* MP2116DQ Package QFN10 (3mm x 3mm) Top Marking Temperature P4 –40°C to +85°C For Tape & Reel, add suffix –Z (eg. MP2116DQ–Z) For Lead Free, add suffix –LF (EG. MP2116DQ–LF–Z) PACKAGE REFERENCE 1 10 2 9 3 8 4 7 5 6 ABSOLUTE MAXIMUM RATINGS (1) Thermal Resistance IN1, OUT1/2 to GND..................–0.3V to + 6.5V IN2 to GND .........................–0.3V to VIN1 + 0.3V SW1 to GND .......................–0.3V to VIN1 + 0.3V ...........(-2.5V<VSW1<+8.5V Transient <50ns) PWROK to GND .........................–0.3V to +6.5V FB1/2, EN1/2 to GND .................–0.3V to +6.5V Operating Temperature............. –40°C to +85°C Continuous Power Dissipation (TA = +25°C)(2) ……………………………………………….2.5W Junction Temperature ...............................150°C Lead Temperature ....................................260°C Storage Temperature ............. –65°C to +150°C QFN10 (3mm x 3mm) .............50 ...... 12 ... °C/W Recommended Operating Conditions (4) θJA θJC Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature TJ(MAX), the junction-toambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD(MAX)=(TJ(MAX)TA)/ θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on approximately 1” square of 1 oz copper. (3) Supply Voltage VIN1 ............................2.5V to 6V Supply Voltage VIN2 .......................... 1.0V to VIN1 Output Voltage VOUT__ ........................0.6V to 6V Operating Temperature............. –40°C to +85°C MP2116 Rev.1.0 1/17/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 2 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO ELECTRICAL CHARACTERISTICS (5) VIN1/2 = VEN1/2 = 3.6V, TA = +25°C, unless otherwise noted. Parameters Condition No Load Supply Current Shutdown Current Thermal Shutdown Trip Threshold PWROK Upper Trip Threshold PWROK Lower Trip Threshold VIN1/2 = 3.6V, VEN1=3.6V, VEN2=0V VFB1 = 0.58V VIN1/2 = 3.6V, VEN1=0V, VEN2=3.6V VFB2 = 0.62V VEN1/2 = 0V, VIN1/2 = 6V Hysteresis = 20°C FB1/2 with respect to the Nominal Value FB1/2 with respect to the Nominal Value ISINK = 5mA Switching Regulator LDO –40°C ≤ TA ≤ +85°C PWROK Output Lower Voltage PWROK Deglitch Timer (FB1) PWROK Deglitch Timer (FB2) EN1/2 Trip Threshold EN1/2 Pull Down Resistor Switching Regulator IN1 Under Voltage Lockout Threshold Rising Edge, Hysteresis=0.3V TA = +25°C Regulated FB1Voltage –40°C ≤ TA ≤ +85°C FB1 Input Bias Current VFB1 = 0.62V SW1 PFET On Resistance ISW1 = 100mA SW1 NFET On Resistance ISW1 = –100mA VEN = 0V, VIN = 6V SW1 Leakage Current VSW = 0V or 6V Duty Cycle = 100%, SW1 PFET Peak Current Limit Current Pulse Width < 1ms Oscillator Frequency Linear Regulator LDO IN2 Input Range Regulated FB2 Voltage FB2 Input Bias Current OUT2 Maximum Output Current OUT2 Current Limit Dropout Voltage ILOAD2 = 10mA, VOUT2=VFB2 TA = +25°C –40°C ≤ TA ≤ +85°C VFB2 = 0.6V VOUT2 = 1.2V VOUT2 = 0V ILOAD = 0.15A, VOUT2 = 1.2V Min Typ Max 300 500 Units μA 70 120 0.01 150 1 10 % –10 % 0.3 0.3 1.90 0.588 0.582 –50 μA °C 50 150 0.96 1 2.15 0.600 0.600 –2 0.20 0.15 V μs 1.5 V MΩ 2.40 0.612 0.618 +50 V –5 V nA Ω Ω +5 μA 2.2 3.1 4.0 A 1.00 1.25 1.50 MHz VIN1 0.612 0.618 +50 V 1 0.588 0.582 –50 500 0.600 0.600 –2 - 600 700 mA 100 mV V nA mA Notes: 5) Production test at +25°C. Specifications over the temperature range are guaranteed by design and characterization. MP2116 Rev.1.0 1/17/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 3 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO PIN FUNCTIONS Pin # Name 1 2 FB1 EN1 3 IN1 4 5 6 7 Description Feedback Input for the switcher output VOUT1. Enable Input for the switcher. Main Input Supply Pin. Input supply for both the switcher and the low dropout (LDO) linear regulator, except the LDO output power device. Switch node of the switcher. SW1 GND Ground. Exposed pad must be connected to GND pin. (Exposed Pad) Input Supply for the linear regulator LDO output power device. Bypass with a 2.2uF IN2 from IN2 to GND. Output of the 500mA LDO. The LDO is designed to be stable with an external 4.7µF OUT2 ceramic capacitor (minimum). 8 PWROK 9 10 EN2 FB2 MP2116 Rev.1.0 1/17/2013 Power OK Open Drain Output. HIGH output indicates that both outputs are within ±10% of the regulation value. LOW output indicates that the output is out of ±10% window. PWROK is pulled down in shutdown. The PWROK window comparators have 50μs deglitch timer for the switcher and 150µs deglitch timer for the linear regulator LDO to avoid false trigger during load transient. Enable Input for the low-dropout LDO Feedback Input for the LDO output VOUT2. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 4 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO TYPICAL PERFORMANCE CHARACTERISTICS VIN=3.6V, VOUT1=1.8V, VOUT2=1.2V, CIN1=10uF, CO1=22uF, CIN2=2.2uF, CO2=4.7uF, L=1uH, TA=25ºC, unless otherwise noted. Switcher Efficiency vs Load Current VIN=2.5V VIN=3.3V Switcher Efficiency vs Load Current VIN=4.0V VIN=3.3V VIN=4.0V VIN=4.0V VIN=5.0V Switcher Efficiency vs Load Current VIN=5.0V VIN=5.0V VOUT1=1.2V VOUT1=1.8V Switcher Output Voltage vs Load Current VOUT1=3.3V Switcher Output Voltage vs Load Current VIN=5.0V VIN=5.0V VIN=5.0V VIN=3.3V VIN=3.3V VIN=2.5V VIN=3.3V VIN=4.0V VIN=4.0V Switcher Output Voltage vs Input Voltage Switcher Output Voltage vs Input Voltage IOUT=0mA IOUT=0mA IOUT=0.1A IOUT=0.1A MP2116 Rev.1.0 1/17/2013 IOUT=0.1A www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 5 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO TYPICAL PERFORMANCE CHARACTERISTICS VIN=3.6V, VOUT1=1.8V, VOUT2=1.2V, CIN1=10uF, CO1=22uF, CIN2=2.2uF, CO2=4.7uF, L=1uH, TA=25ºC, unless otherwise noted. Peak Current vs Duty Cycle Enable Turn On PWROK 2V/div V OUT1 2V/div VOUT1 2V/div V OUT2 2V/div VOUT2 2V/div V EN 2V/div V EN 2V/div 1.203 1.22 1.202 1.21 VIN2=2V 1.20 VIN2=3V VOUT2 (V) 1.201 1.200 1.19 1.199 1.18 1.198 1.802 0.40 1.801 VIN2=3.0V VOUT2 (V) 1.23 1.800 IOUT=0.2A 1.799 IOUT=0.1A 1.798 1.797 LDO DROPOUT (V) VOUT2 (V) PWROK 2V/div VIN2=2.5V MP2116 Rev.1.0 1/17/2013 Enable Turn Off IOUT=0.2A IOUT=0.1A 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 6 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO TYPICAL PERFORMANCE CHARACTERISTICS VIN=3.6V, VOUT1=1.8V, VOUT2=1.2V, CIN1=10uF, CO1=22uF, CIN2=2.2uF, CO2=4.7uF, L=1uH, TA=25ºC, unless otherwise noted. MP2116 Rev.1.0 1/17/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 7 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO TYPICAL PERFORMANCE CHARACTERISTICS VFB1 VFB2 -50 -10 30 70 110 150 1.5 2.5 1.4 2.3 UVLO (V) FREQUENCY (MHz) VIN=3.6V, VOUT1=1.8V, VOUT2=1.2V, CIN1=10uF, CO1=22uF, CIN2=2.2uF, CO2=4.7uF, L=1uH, TA=25ºC, unless otherwise noted. 1.3 1.2 1.1 1 -50 2.1 1.9 1.7 -10 30 70 110 150 1.5 -50 -10 30 70 110 150 D=100% MP2116 Rev.1.0 1/17/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 8 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO OPERATION IN1 + IAMP 10X -CURRENT SENSE AMP BIAS & VOLTAGE REFERENCE ICS FB1 + + + PWMCMP EAMP1 -- PWM DH MAIN SWITCH (PCH) -- SW1 1.25MHz OSCILLATOR SYNCHRONOUS RECTIFIER (NCH) OSC DL GND IN2 + FB2 EAO2 0.6V FB1/2 -- + 0.66V OUT2 OUT_Hi PWROK -POWER ON RESET WINDOW COMPARATORS 0.54V + NO GOOD OUT_Lo -- Figure1―MP2116 Functional Block Diagramm The MP2116 is a 1.25MHz current mode 2A synchronous step-down switcher plus a low input 0.5A low dropout (LDO) linear regulator (see Figure1). The MP2116 is optimized for low voltage, Li-Ion battery powered applications where high efficiency and small size are critical. The MP2116 uses an external resistor divider to set both the switcher and LDO output voltage from 0.6V to 6V. 2A Synchronous Step-Down Switcher The switcher integrates both a main switch and a synchronous rectifier, which provides high efficiency and eliminates an external Schottky diode. The duty cycle D of a step-down switcher is defined as: D = TON × fOSC × 100% ≈ VOUT × 100% VIN Where TON is the main switch on time and fOSC is the oscillator frequency (1.25MHz). MP2116 Rev.1.0 1/17/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 9 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO Current Mode PWM Control Slope compensated current mode PWM control provides stable switching and cycle-by-cycle current limiting for superior load and line response in addition to protection of the internal main switch and synchronous rectifier. The MP2116 switches at a constant frequency (1.25MHz) and regulates the output voltage. During each cycle the PWM comparator modulates the power transferred to the load by changing the inductor peak current based on the feedback error voltage. During normal operation, the main switch is turned on for a certain time to ramp the inductor current at each rising edge of the internal oscillator, and switched off when the peak inductor current is above the error voltage. When the main switch is off, the synchronous rectifier will be turned on immediately and stay on until the next cycle starts. Dropout Operation The MP2116 allows the main switch to remain on for more than one switching cycle and increases the duty cycle while the input voltage is dropping close to the output voltage. When the duty cycle reaches 100%, the main switch is held on continuously to deliver current to the output up to the PFET current limit. The output voltage then becomes the input voltage minus the voltage drop across the main switch and the inductor. Power OK The MP2116 provides an open-drain PWROK output that goes high after both channels reach regulation during startup. PWROK goes low after one of the output channels goes out of regulation by ±10% or when device enters shutdown. There are deglitch timers built in to avoid PWROK false triggered during load transient: 50µS for the switcher and 150µS for the LDO. Low Input 0.5A Linear Regulator The low input 0.5A low dropout (LDO) linear regulator has separate input IN2 and output OUT2 pins for the internal power PNP device. The control circuitry of the LDO takes power from the main input supply IN1. Both IN1 and IN2 input supplies must be presented for the LDO working properly. The LDO power device input IN2 can be connected to the switcher output (Figure1) or directly to the main supply IN1 (Figure3). If the IN2 tied to the IN1, it is optional to insert a RC filter between IN1 and IN2. The RC filter will reduce switching noise coupling from IN1 to IN2 and power dissipation inside the MP2116 Short Circuit Protection When the output is shorted to ground, the oscillator frequency is reduced to prevent the inductor current from increasing beyond the PFET current limit. The PFET current limit is also reduced to lower the short circuit current. The frequency and current limit will return to the normal values once the short circuit condition is removed and the feedback voltage reaches 0.6V. Maximum Switcher Output Current The MP2116 switcher can provide up to 2A output current, and operate down to 3V input voltage; however the maximum output current decreases at lower input voltage due to a large IR drop on the main switch and synchronous rectifier. The slope compensation signal reduces the peak inductor current as a function of the duty cycle to prevent sub-harmonic oscillations at duty cycles greater than 50%. Conversely, the current limit increases as the duty cycle decreases MP2116 Rev.1.0 1/17/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 10 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO APPLICATION INFORMATION Output Voltage Setting The external resistor divider sets the output voltage. The feedback resistor R1 of the switcher also sets the feedback loop bandwidth with the internal compensation capacitor (see Figure1). Choose R1 feedback resistor of the switcher between 450kΩ and 800kΩ for optimal transient response. R2 is then given by: R2 = R1 VOUT1 −1 0.6V See Table1 for recommended R1 & R2 resistor values. Choose R4 of the LDO between 10kΩ and 100kΩ. R3 is then given by: V R3 = R4 × ( OUT2 − 1) 0.6V Table 1—Resistor Selection vs. Output Voltage Setting VOUT R1 R2 1.2V 1.5V 1.8V 2.5V 499kΩ (1%) 499kΩ (1%) 499kΩ (1%) 332kΩ (1%) 499kΩ (1%) 249kΩ (1%) 499kΩ (1%) 158kΩ (1%) Inductor Selection A 1μH to 10μH inductor with DC current rating at least 25% higher than the maximum load current is recommended for most applications. For best efficiency, the inductor DC resistance shall be <100mΩ. See Table 2 for recommended inductors and manufacturers. For most designs, the inductance value can be derived from the following equation: L= VOUT × (VIN − VOUT ) VIN × ΔIL × fOSC Where ΔIL is inductor ripple current. Choose inductor ripple current approximately 30% of the maximum load current, up to 2A. The maximum inductor peak current is: ΔI IL(MAX) = ILOAD(MAX) + L 2 Switcher Input Capacitor CIN1 Selection The input capacitor reduces the surge current drawn from the input and switching noise from the device. The input capacitor impedance at the switching frequency shall be less than input source impedance to prevent high frequency switching current passing to the input. Ceramic capacitors with X5R or X7R dielectrics are highly recommended because of their low ESR and small temperature coefficients. For most applications, a 10μF~22μF capacitor is sufficient. Switcher Output Capacitor CO1 Selection The output capacitor keeps output voltage ripple small and ensures regulation loop stable. The output capacitor impedance shall be low at the switching frequency. Ceramic capacitors with X5R or X7R dielectrics are recommended. For most applications, a 22μF~47μF capacitor is sufficient. The output ripple ΔVOUT is approximately: ΔVOUT1 ≤ VOUT1 × ( VIN1 − VOUT1 ) ⎛ ⎞ 1 × ⎜ ESR + ⎟ VIN1 × fOSC × L 8 × f × C OSC O1 ⎠ ⎝ Table 2—Suggested Surface Mount Inductors Manufacturer Part Number Inductance (uH) TOKO SUMIDA DELTA D62LCB CDRH4D28C SIL525-1R0 1.0 1.0 1.0 MP2116 Rev.1.0 1/17/2013 Max DCR (mΩ) 17 17.5 38 Saturation Current (A) 3.5 3.0 3.2 Dimensions L x W x H (mm3) 6.2 X6.3 X 2.0 5.1 X 5.1 X 3 5.0 X 5.0 X 2.5 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 11 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO Thermal Dissipation Power dissipation shall be considered when both channels of the MP2116 provide maximum 2A switcher output current and 0.5A LDO output current to the loads at high ambient temperature. If the junction temperature rises above 150°C, the MP2116 two channels will be shut down. PC Board Layout The high current paths (GND, IN1/IN2 and SW1) should be placed very close to the device with short, direct and wide traces. Input capacitors should be placed as close as possible to the respective IN and GND pins. The external feedback resistors shall be placed next to the FB pins. Keep the switching nodes SW1 short and away from the feedback network The junction-to-ambient thermal resistance of the 10-pin QFN (3mm x 3mm) RΘJA is 50°C/W. The maximum power dissipation is about 1.6W when the MP2116 is operating in a 70°C ambient temperature environment. PD MAX = 150 o C − 70 o C 50 o C / W = 1 .6 W TYPICAL APPLICATION CIRCUITS OPTIONAL 2 3 4 6 1 MP2116 Rev.1.0 1/17/2013 EN1 IN1 SW1 EN2 PWROK MP2116 OUT2 IN2 FB2 FB1 GND 9 POWER OK 8 7 OUT2 10 5 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 12 MP2116 –2A, 6V, 100% DUTY CYCLE SYNCHROOUS STEP-DOWN CONVERTER WITH 0.5A LDO PACKAGE INFORMATION (3mmx3mm) QFN10 NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP2116 Rev.1.0 1/17/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication © 2013 MPS. All Rights Reserved. 13