LM60 2.7V, SOT-23 or TO-92 Temperature Sensor General Description n Available in SOT-23 and TO-92 packages The LM60 is a precision integrated-circuit temperature sensor that can sense a −40˚C to +125˚C temperature range while operating from a single +2.7V supply. The LM60’s output voltage is linearly proportional to Celsius (Centigrade) temperature (+6.25 mV/˚C) and has a DC offset of +424 mV. The offset allows reading negative temperatures without the need for a negative supply. The nominal output voltage of the LM60 ranges from +174 mV to +1205 mV for a −40˚C to +125˚C temperature range. The LM60 is calibrated to provide accuracies of ± 2.0˚C at room temperature and ± 3˚C over the full −25˚C to +125˚C temperature range. The LM60’s linear output, +424 mV offset, and factory calibration simplify external circuitry required in a single supply environment where reading negative temperatures is required. Because the LM60’s quiescent current is less than 110 µA, self-heating is limited to a very low 0.1˚C in still air in the SOT-23 package. Shutdown capability for the LM60 is intrinsic because its inherent low power consumption allows it to be powered directly from the output of many logic gates. Applications Features n Calibrated linear scale factor of +6.25 mV/˚C n Rated for full −40˚ to +125˚C range n Suitable for remote applications n n n n n n n n n Cellular Phones Computers Power Supply Modules Battery Management FAX Machines Printers HVAC Disk Drives Appliances Key Specifications n n n n n n n n ± 2.0 and ± 3.0˚C (max) Accuracy at 25˚C: ± 4.0˚C (max) Accuracy for −40˚C to +125˚C: ± 3.0˚C (max) Accuracy for −25˚C to +125˚C: Temperature Slope: +6.25mV/˚C Power Supply Voltage Range: +2.7V to +10V Current Drain @ 25˚C: 110µA (max) Nonlinearity: ± 0.8˚C (max) Output Impedance: 800Ω (max) Typical Application Connection Diagrams SOT-23 01268101 01268102 VO = (+6.25 mV/˚C x T ˚C) + 424 mV Temperature (T) Typical VO +125˚C +1205 mV +100˚C +1049 mV +25˚C +580 mV 0˚C +424 mV −25˚C +268 mV −40˚C +174 mV Top View See NS Package Number MA03B TO-92 01268123 See NS Package Number Z03A FIGURE 1. Full-Range Centigrade Temperature Sensor (−40˚C to +125˚C) Operating from a Single Li-Ion Battery Cell © 2001 National Semiconductor Corporation DS012681 www.national.com LM60 2.7V, SOT-23 or TO-92 Temperature Sensor July 2001 LM60 Ordering Information Order Number Device Marking Supplied In LM60BIM3 T6B 1000 Units on Tape and Reel LM60BIM3X T6B 3000 Units on Tape and Reel LM60CIM3 T6C 1000 Units on Tape and Reel T6C 3000 Units on Tape and Reel LM60CIM3X LM60BIZ LM60BIZ Bulk LM60CIZ LM60CIZ Bulk www.national.com 2 Accuracy Over Specified Temperature Range Specified Temperature Range ±3 −25˚C ≤ TA ≤ +125˚C ±4 −40˚C ≤ TA ≤ +125˚C ±3 −25˚C ≤ TA ≤ +125˚C ±4 −40˚C ≤ TA ≤ +125˚C Package Type SOT-23 TO-92 Supply Voltage (Note 1) Storage Temperature −65˚C to +150˚C +12V to −0.2V Output Voltage (+V S Maximum Junction Temperature (TJMAX) + 0.6V) to −0.6V Output Current 10 mA Input Current at any pin (Note 2) +125˚C Operating Ratings(Note 1) 5 mA ESD Susceptibility (Note 3) : TMIN ≤ TA ≤ TMAX Specified Temperature Range: Human Body Model 2500V Machine Model SOT-23 TO-92 250V 200V Recommended Lead Temperature (Note 4): SOT Package: Vapor Phase (60 sec) Infrared (15 sec) TO-92 Package (3 sec, dwell time) LM60B −25˚C ≤ TA ≤ +125˚C LM60C −40˚C ≤ TA ≤ +125˚C Supply Voltage Range (+VS) +2.7V to +10V Thermal Resistance, θJA (Note 5) SOT-23 TO-92 450˚C/W 180˚C/W +215˚C +220˚C +240˚C Electrical Characteristics Unless otherwise noted, these specifications apply for +VS = +3.0 VDC and I = TMIN to TMAX ; all other limits TA = TJ = 25˚C. Parameter Conditions LOAD Typical (Note 6) Accuracy (Note 8) Output Voltage at 0˚C Sensor Gain +6.25 (Average Slope) Output Impedance Quiescent Current Change of Quiescent Current LM60B LM60C Units (Limit) Limits Limits (Note 7) (Note 7) ± 2.0 ± 3.0 ± 3.0 ± 4.0 ˚C (max) ± 0.6 ± 0.8 ˚C (max) +6.06 +6.00 mV/˚C (min) +6.44 +6.50 mV/˚C (max) 800 800 Ω (max) ± 0.3 ± 2.3 ± 0.3 ± 2.3 mV/V (max) 110 110 µA (max) 125 125 µA (max) ˚C (max) +424 Nonlinearity (Note 9) Line Regulation (Note 10) = 1 µA. Boldface limits apply for TA = TJ +3.0V ≤ +V S ≤ +10V +2.7V ≤ +V S ≤ +3.3V +2.7V ≤ +V S ≤ +10V +2.7V ≤ +V S 82 ≤ +10V Temperature Coefficient of mV mV (max) ± 5.0 µA (max) 0.2 µA/˚C ± 0.2 ˚C Quiescent Current Long Term Stability (Note 11) T J =TMAX =+125˚C, for 1000 hours Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: When the input voltage (VI) at any pin exceeds power supplies (VI < GND or VI > +VS), the current at that pin should be limited to 5 mA. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin. Note 4: See the URL ”http://www.national.com/packaging/“ for other recomdations and methods of soldering surface mount devices. Note 5: The junction to ambient thermal resistance (θJA) is specified without a heat sink in still air. Note 6: Typicals are at TJ = TA = 25˚C and represent most likely parametric norm. Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 8: Accuracy is defined as the error between the output voltage and +6.25 mV/˚C times the device’s case temperature plus 424 mV, at specified conditions of voltage, current, and temperature (expressed in ˚C). Note 9: Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the device’s rated temperature range. 3 www.national.com LM60 Absolute Maximum Ratings LM60 Electrical Characteristics (Continued) Note 10: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects can be computed by multiplying the internal dissipation by the thermal resistance. Note 11: For best long-term stability, any precision circuit will give best results if the unit is aged at a warm temperature, and/or temperature cycled for at least 46 hours before long-term life test begins. This is especially true when a small (Surface-Mount) part is wave-soldered; allow time for stress relaxation to occur. The majority of the drift will occur in the first 1000 hours at elevated temperatures. The drift after 1000 hours will not continue at the first 1000 hour rate. Typical Performance Characteristics To generate these curves the LM60 was mounted to a printed circuit board as shown in Figure 2. Thermal Resistance Junction to Air Thermal Time Constant 01268103 Thermal Response in Stirred Oil Bath with Heat Sink 01268104 Start-Up Voltage vs. Temperature 01268106 Quiescent Current vs. Temperature 01268105 Thermal Response in Still Air without a Heat Sink 01268107 Accuracy vs Temperature 01268109 www.national.com Thermal Response in Still Air with Heat Sink 01268110 4 01268108 Noise Voltage 01268111 To generate these curves the LM60 was mounted to a printed circuit board as shown in Figure 2. (Continued) Supply Voltage vs Supply Current Start-Up Response 01268122 01268112 01268114 FIGURE 2. Printed Circuit Board Used for Heat Sink to Generate All Curves. 1⁄2" Square Printed Circuit Board with 2 oz. Copper Foil or Similar. into a threaded hole in a tank. As with any IC, the LM60 and accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to ensure that moisture cannot corrode the LM60 or its connections. The thermal resistance junction to ambient (θJA ) is the parameter used to calculate the rise of a device junction temperature due to the device power dissipation. For the LM60 the equation used to calculate the rise in the die temperature is as follows: TJ = TA + θ JA [(+VS IQ) + (+VS − VO) IL] 1.0 Mounting The LM60 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued or cemented to a surface. The temperature that the LM60 is sensing will be within about +0.1˚C of the surface temperature that LM60’s leads are attached to. This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature were much higher or lower than the surface temperature, the actual temperature of the LM60 die would be at an intermediate temperature between the surface temperature and the air temperature. To ensure good thermal conductivity the backside of the LM60 die is directly attached to the GND pin. The lands and traces to the LM60 will, of course, be part of the printed circuit board, which is the object whose temperature is being measured. These printed circuit board lands and traces will not cause the LM60’s temperature to deviate from the desired temperature. Alternatively, the LM60 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or screwed where IQ is the quiescent current and ILis the load current on the output. The table shown in Figure 3 summarizes the rise in die temperature of the LM60 without any loading, and the thermal resistance for different conditions. 5 www.national.com LM60 Typical Performance Characteristics LM60 1.0 Mounting (Continued) SOT-23* SOT-23** TO-92* TO-92*** no heat sink small heat fin no heat fin small heat fin θ JA Still air T J − TA θ JA T J − TA θ JA T J − TA θ JA T J − TA (˚C/W) (˚C) (˚C/W) (˚C) 450 0.17 260 0.1 180 0.07 140 0.05 180 0.07 90 0.034 70 0.026 Moving air *-Part soldered to 30 gauge wire. **-Heat sink used is 1⁄2" square printed circuit board with 2 oz. foil with part attached as shown in Figure 2 . ***-Part glued or leads soldered to 1” square of 1/16” printed circuit board with 2 oz. foil or similar. FIGURE 3. Temperature Rise of LM60 Due to Self-Heating and Thermal Resistance (θJA) 2.0 Capacitive Loads The LM60 handles capacitive loading well. Without any special precautions, the LM60 can drive any capacitive load as shown in Figure 4. Over the specified temperature range the LM60 has a maximum output impedance of 800Ω. In an extremely noisy environment it may be necessary to add some filtering to minimize noise pickup. It is recommended that 0.1 µF be added from +V S to GND to bypass the power supply voltage, as shown in Figure 5. In a noisy environment it may be necessary to add a capacitor from the output to ground. A 1 µF output capacitor with the 800Ω output impedance will form a 199 Hz lowpass filter. Since the thermal time constant of the LM60 is much slower than the 6.3 ms time constant formed by the RC, the overall response time of the LM60 will not be significantly affected. For much larger capacitors this additional time lag will increase the overall response time of the LM60. 01268115 FIGURE 4. LM60 No Decoupling Required for Capacitive Load 01268116 FIGURE 5. LM60 with Filter for Noisy Environment www.national.com 6 LM60 2.0 Capacitive Loads (Continued) 01268117 FIGURE 6. Simplified Schematic 3.0 Applications Circuits 01268118 FIGURE 7. Centigrade Thermostat 01268119 FIGURE 8. Conserving Power Dissipation with Shutdown 7 www.national.com LM60 Physical Dimensions inches (millimeters) unless otherwise noted SOT-23 Molded Small Outline Transistor Package (M3) Order Number LM60BIM3 or LM60CIM3 NS Package Number MA03B www.national.com 8 LM60 2.7V, SOT-23 or TO-92 Temperature Sensor Physical Dimensions inches (millimeters) unless otherwise noted (Continued) TO-92 Molded Plastic Package (Z) Order Number LM60BIZ or LM60CIZ Package Number Z03A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.