PI90LV031A PI90LV027A PI90LV017A 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 3V LVDS High-Speed Differential Line Drivers Features Description • Signaling Rates >400Mbps (200 MHz) The PI90LV031A, PI90LV027A, and PI90LV017A are differential line drivers that use low-voltage differential signaling (LVDS) to support data rates in excess of 400 Mbps. These products are designed for applications requiring high-speed, low-power consumption and low noise generation. • Single 3.3V Power Supply Design • ±350mV Differential Swing • Maximum Differential Skew of 0.4ns A low voltage TTL/CMOS input level is translated by the device into a low-voltage (350mV) differential output signal. Exclusive to the PI90LV031A quad driver is a power-down mode that 3-states the outputs and places the device in a low-power idle state (13mW typical). • Maximum Propagation Delay of 2.0ns • Maximum Power Dissipation: 25mW @ 200 MHz/driver • Low Voltage TTL (LVTTL) Inputs • Industrial Temperature Operating Range: -40°C to 85°C Applications Applications include point-to-point and multidrop baseband data transmission over controlled impedance media of approximately 100 ohms. The transmission media can be printed circuit board traces, backplanes, or cables. • Meets or Exceeds IEEE 1596.3 SCI LVDS Standard • Meets or Exceeds ANSI/TIA/EIA-644 LVDS Standard The PI90LV031A, PI90LV027A, PI90LV017A and companion line receivers (PI90LV032A, PI90LV028A, and PI90LV018A) provide new alternatives to RS-232, PECL, and ECL devices for high-speed, point-to-point interface applications. • Packaging (Pb-free & Green available): PI90LV017A & PI90LV027A - 8-pin SOIC (W) - 8-pin MSOP (U) PI90LV031A - 16-pin SOIC (W) - 16-pin TSSOP (L) PI90LV027A VCC DIN1 DIN2 GND PI90LV031A DIN1 DIN1 DOUT1+ DOUT1EN DOUT2DOUT2+ DIN2 GND 1 2 3 4 5 6 7 8 16-Pin L,W 16 15 14 13 12 11 10 9 VCC DIN4 DOUT4+ DOUT4EN* DOUT3DOUT3+ DIN3 D1 DIN2 D2 DIN3 D3 DIN4 D4 DOUT1+ DOUT1- DOUT1DOUT1+ DOUT2+ DOUT2- DIN1 D1 DIN2 D2 DIN1 D1 DOUT1+ DOUT1DOUT2+ DOUT2- DOUT2+ DOUT2- PI90LV017A DOUT3+ DOUT3DOUT4+ VCC DIN1 NC GND DOUT4- EN EN* 08-0295 1 8 2 8-Pin 7 3 U,W 6 4 5 1 1 8 2 8-Pin 7 3 U,W 6 4 5 DOUT1DOUT1+ NC NC DOUT1+ DOUT1- PS8422D 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Function Tables Pin Descriptions PI90LV031A Enable s Input Outputs Name De s cription EN EN DIN DOUT+ DOUT– DIN TTL/CMOS driver input pins H X H H L DO+ Non- inverting driver output pins H X L L H DO– Inverting driver output pins X L H H L GND Ground pin X L L L H VCC Positive power supply pin, +3.3V ±10% L H X Z Z PI90LV027A Recommended Operating Conditions Input Outputs DIN DOUT+ DOUT- H H L L L H M in. Typ. M a x. Units Supply Voltage (VCC) +3.0 +3.3 +3.6 V Operating Free Air Temperature –40 +25 +85 °C PI90LV017A Input Outputs Absolute Maximum Ratings (see Note 1, Page 4) DIN DOUT+ DOUT- H H L L L H Supply Voltage (VCC) ........................................... –0.3V to +4.0V Input Voltage (DIN) .................................... –0.3V to (VCC +0.3V) Enable Input Voltage (EN, EN*) ................. –0.3V to (VCC +0.3V) Output Voltage (DOUT+, DOUT-) ......................... –0.3V to +3.9V Short Circuit Duration (DOUT+, DOUT-) ..................................................... Continuous S Package ........................................................................ 750mW Derate S Package .................................... 8.5mW/°C above +25°C Storage Temperature Range ............................... -65°C to +150°C Lead Temperature Range Soldering (4s) .......................... +260°C Maximum Junction Temperature ...................................... +150°C ESD Rating .......................................................................... ≥6kV Note: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 08-0295 2 PS8422D 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Electrical Characteristics Over supply voltage and operating temperature ranges, unless otherwise specified. (Notes 2,3,4) Symbol Parame te r Conditions VOD1 Differential Output Voltage ΔVOD1 Change in Magnitude of VOD1 for Complementary Output States VOS Offset Voltage ΔVOS Change in Magnitude of VOS for Complementary Output States VOH Output Voltage High VOL Output Voltage Low 0 . 90 VIH Input Voltage High 2.0 VCC VIL Input Voltage Low GND 0.8 RL = 100Ω (Fig.1) Pin DOUTDOUT+ M in. Typ. M ax. Units 250 350 45 0 mV 4 35 ImVI 1.25 1.375 V 5 25 ImVI 1.38 1.6 1.125 1.03 V IIH Input Current VIN = VCC or 2.5V IIL Input Current VCL IOS - 10 ±1 +10 VIN = GND or 0.4V - 10 ±1 +10 Input Clamp Voltage ICL = - 18mA - 1.5 - 0. 8 Output Short Circuit Current ENABLED,(10) DIN = VCC, DOUT+ = 0V or DIN = GND, DOUT- = 0V IOSD Differential Output Short Circuit Current ENABLED, VOD = 0V(10) IOFF Power- off Leakage VOUT = 0V or 3.6V, VCC = 0V or Open IOZ Output Three- State Current EN = 0.8V and EN* = 2.0V VOUT = 0V or VCC ICC No Load Supply Current Drivers Enabled DIN = VCC or GND ICCL Loaded Supply Current Drivers Enabled RL = 100Ω All Channels, DIN = VCC or GND (all inputs) ICCZ No Load Supply Current Drivers Disabled DIN = VCC or GND, EN = GND, EN* = VCC 08-0295 DIN EN EN* 3 - 6.0 μA V - 9.0 mA DOUTDOUT+ - 20 - 6.0 - 9.0 ±1 +20 μA - 10 VCC ±1 +10 5.0 8.0 23 30 2.6 6.0 PS8422D mA 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Switching Characteristics VCC = +3.3V ±10%, TA = -40°C to +85°C (Notes 3,9,11) Symbol Parame te r Conditions M in. Typ. M a x. tPHLD Differential Propagation Delay High to Low 0.8 1.18 2.0 tPLHD Differential Propagation Delay Low to High 0.8 1.25 2. 0 tSKD1 Differential Pulse Skew ItPHLD - tPLHDI (5) 0 0.07 0.4 tSKD2 Channel- to- Channel Skew(6) 0 0.1 0.5 tSKD3 Differential Part- to- Part Skew (7) tSKD4 Differential Part- to- Part Skew (8) tTLH Rise Time 0.38 1.5 tTHL Fall Time 0.40 1.5 tPHZ Disable Time High to Z tPLZ Disable Time Low to Z tPZH Enable Time Z to High tPZL Enable Time Z to Low tMAX Maximum Operating Frequency(13) RL = 100Ω, CL = 10pF (Figures 2 & 3) 0 1.0 0 1.2 Units ns 5 RL = 100Ω, CL = 10pF (Figures 4 & 5) 5 7 7 200 2 50 MHz Notes: 1. “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. 2. Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except: VOD1 and ΔVOD1. 3. All typicals are given for: VCC = +3.3V, TA = +25°C. 4. The PI90LV031A/PI90LV027A/PI90LV017A are current mode devices and only functions within datasheet specifications when a resistive load is applied to the driver outputs typical range is (90Ω to 110Ω). 5. tSKD1, ItPHLD - tPLHDI is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the same channel. 6. tSKD2 is the Differential Channel-to-Channel Skew of any event on the same device. 7. tSKD3, Differential Part-to-Part Skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This specification applies to devices at the same Vcc and with 5°C of each other within the operating temperature range. 8. tSKD4, Part-to-Part Skew, is the differential Channel-to-Channel skew of any event between devices. This specification applies to devices over recommended operating temperature and voltage ranges, and across process distribution. tSKD4 is defined as IMax - MinI differential propagation delay. 9. Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO = 50Ω, tr ≤ 1ns, and tf ≤ 1ns. 10. Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only. 11. CL includes probe and jig capacitance. 12. All input voltages are for one channel unless otherwise specified. Other inputs are set to GND. 13. fMAX generator input conditions: tR = tF < 1ns, (0% to 100%), 50% duty cycle, 0V to 3V. Output Criteria: duty cycle = 45%/55%, VOD > 250mV, all channels switching. 08-0295 4 PS8422D 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Parameter Measurement Information DOUT+ RL/2 VCC DIN GND VOS D S1 VOD RL/2 DOUT- Driver ENABLED Figure 1. Driver VOD and VOS Test Circuit CL DOUT+ Generator DIN RL D 50-Ohm DOUTDriver ENABLED CL Figure 2. Driver Propagation Delay and Transition Time Test Circuit 08-0295 5 PS8422D 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Figure 3. Driver Propagation Delay and Transition Time Waveforms Figure 4. Driver Three-State Delay Test Circuit 08-0295 6 PS8422D 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Figure 5. Driver 3-State Delay Waveform Figure 6. Point-to-Point Application 08-0295 7 PS8422D 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Packaging Mechanical: 16-Pin SOIC (W) DOCUMENT CONTROL NO. PD - 1004 16 REVISION: E DATE: 03/09/05 .149 .157 3.78 3.99 1 .0099 .0196 .386 .393 9.80 10.00 0.25 [Û 0.50 .0075 .0098 Û 1 .053 .068 .0155 .0260 0.393 0.660 REF 1.35 1.75 0.41 1.27 SEATING PLANE .050 BSC 1.27 .013 .020 0.330 0.508 .0040 0.10 .0098 0.25 .016 .050 .2284 .2440 5.80 6.20 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Notes: 1) Controlling dimensions in millimeters. 2) Ref: JEDEC MS-012D/AC 08-0295 0.19 0.25 DESCRIPTION: 16-Pin, 150-Mil Wide, SOIC PACKAGE CODE: W 8 PS8422D 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Packaging Mechanical: 8-Pin SOIC (W) DOCUMENT CONTROL NO. PD - 1001 8 REVISION: F .149 .157 DATE: 03/09/05 3.78 3.99 .0099 .0196 0.25 [Û 0.50 1 .189 .196 4.80 5.00 .0075 .0098 Û 0.19 0.25 0.40 .016 1.27 .050 1 .016 .026 0.406 0.660 .2284 .2440 5.80 6.20 1.35 1.75 .053 .068 SEATING PLANE REF .050 BSC 1.27 .0040 0.10 .0098 0.25 .013 0.330 .020 0.508 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Notes: 1) Controlling dimensions in millimeters. 2) Ref: JEDEC MS-012D/AA 08-0295 DESCRIPTION: 8-Pin, 150-Mil Wide, SOIC PACKAGE CODE: W 9 PS8422D 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Packaging Mechanical: 16-Pin TSSOP (L) DOCUMENT CONTROL NO. PD - 1310 REVISION: E 16 DATE: 03/09/05 .169 .177 1 1 .0256 BSC 0.65 .193 .201 4.9 5.1 .007 .012 4.3 4.5 .004 .008 .047 max. 1.20 .002 .006 0.09 0.20 0.45 .018 0.75 .030 SEATING PLANE .252 BSC 6.4 0.05 0.15 0.19 0.30 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com Note: 1. Package Outline Exclusive of Mold Flash and Metal Burr 2. Controlling dimentions in millimeters 3. Ref: JEDEC MO-153F/AB DESCRIPTION: 16-Pin, 173-Mil Wide, TSSOP PACKAGE CODE: L 08-0295 10 PS8422D 11/11/08 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Packaging Mechanical: 8-pin MSOP (U) -AX 0$ 2%6)3)/.% $!4% 'AUGE 0LANE $/#5-%.4#/.42/,./ -AX 2%& $ETAIL! $ETAIL! -!8 -!8 3HULFRP6HPLFRQGXFWRU&RUSRUDWLRQ 1VW6WUHHW6DQ-RVH&$ ZZZSHULFRPFRP .OTES #ONTROLLING$IMENSIONSIN-ILLIMETERS 2EF*%$%#-/%!! $%3#2)04)/.0IN-INI3MALL/UTLINE0ACKAGE-3/0 0!#+!'%#/$%5 Ordering Information Ordering Code Package Code Package Description PI90LV017AWE W Pb-free & Green, 8-pin SOIC PI90LV017AUE U Pb-free & Green, 8-pin MSOP PI90LV027AWE W Pb-free & Green, 8-pin SOIC PI90LV027AUE U Pb-free & Green, 8-pin MSOP PI90LV031AWE W Pb-free & Green, 16-pin SOIC PI90LV031ALE L Pb-free & Green, 16-pin TSSOP Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 08-0295 11 PS8422D 11/11/08