95040 PA2011 Low RDSON SPDT Analog Switch. ANALOG PRODUCTS DIVISION Features • • • • • Description Low Voltage Operation (1.8 V to 3.3 V) Low On-Resistance - rON: 1.8 at 2.7 V Low Charge Injection Low Voltage Logic Compatible DFN-6 Package or SC70-6 Package The PA2011 is a low on-resistance, single-pole doublethrow monolithic CMOS analog switch. It is designed for low voltage applications with guaranteed operation at 2 V. The PA2011 is ideal for portable and battery powered equipment, requiring high performance and efficient use of board space. In additional to the low on-resistance (1.8 at 2.7 V), charge injection is less than 10 pC over the entire analog range. Benefits • • • • • Reduced Power Consumption Simple Logic Interface High Accuracy Reduce Board Space Guaranteed 2 V Operation The switch conducts equally well in both directions when on, and blocks up to the power supply level when off. Break-before-make is guaranteed. The PA2011 is mounted in a 1.6 x 1.6 mm DFN-6 or SC70-6 lead package, reducing board spacing by approximately 40 % Applications • • • • • • • Cellular Phones Communication Systems Portable Test Equipment Battery Operated Systems Sample and Hold Circuits ADC and DAC Applications USB 1.1 Interfaces Pin Configuration DFN-6 IN V+ GND 1 SC70-6 6 2 5 3 4 NO (Source1) COM NC (Source2) NO (Source1) 6 1 IN COM 2 V+ 5 NC (Source2) 4 Top View 3 GND Top View Truth Table Logic NC NO 0 ON OFF 1 OFF ON Typical Application Ordering information Temp. Range -40 to 85 °C Package Part Number DFN-6 PA2011DN-T7 SC70-6 PA2011SC-T7 SC70-6 PA2011SC-T13 Display µP with soft Modem Audio Codec & ASIC Mic. Pre-Amp PA2011 Internal Hands Free Mic Mic Audio Amplifier Spkr Spkr PA2011 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 431-2288 www.protekanalog.com 95040 Rev.3. 10/11 NOT FOR USE IN LIFE SUPPORT SYSTEMS 1 PA2011 ANALOG PRODUCTS DIVISION Low RDSON SPDT Analog Switch. Absolute Maximum Ratings TA = 25 °C, unless otherwise noted Parameter Limit Reference V+ to Ground IN, COM, NC, NO Unit -0.3 to 4.2 1 V -0.3 to (Vcc+ 0.3V) Continuous Current (NO,NC,COM pins) ±150 Peak Current (Pulsed at 1mS, 10% duty cycle) ±300 Storage Temperature Power Dissipation mA -65 to +150 °C 172 mW Notes 1. Signals on NC, NO, or COM or IN exceeding V+ will be clamped by internal diodes. Limit forward diode current to maximum current ratings Specifications V+ = 2.0V Test Conditions unless otherwise specified: V+ = 2.0 V, VIN = 0.4 V or 1.6 V Parameter Symbol Test Conditions Temp Min Typ Max Unit VCC V 5.5 5.5 Ω Analog Switch Full VNO,VNC, VCOM Analog Signal Range On-Resistance RON IOFF(NO) or IOFF(NC) Switch Off Leakage Current ICOM(OFF) Channel On Leakage Current ICOM(ON) VCC = 2.0V, VCOM = 0.2V- 0.9V INO , INC = 20mA, V+ = 2.2 V, VNO, VNC= 0.5 V/1.5 V, VCOM = 1.5 V/0.5 V V+ = 2.2 V, VNO, VNC= 0.5 V/1.5 V, VCOM = 1.5 V/0.5 V V+ = 2.2 V, VNO, VNC = VCOM = 0.5 V/1.5 V 0.0 Room Full 3.5 Room Full -1 -10 -1 -10 Room Full -1 -10 -1 -10 Room Full -1 -10 -1 -10 1.5 nA Digital Control Input High Voltage VINH Full Input Low Voltage VINL Full Input Capacitance Cin Full IINL or IINH Input Current VnA VIN = 0 or V+ Full 0.4 4 1 pF 1 µA Dynamic Characteristics Room Full 75 110 113 Room Full 37 71 76 tBBM Room Full 37 Charge Injection QINJ Room Off Isolation OIRR Crosstalk XTALK Room NO, NC OFF Capacitance CNO(off) CNC(off) Room Chanel On Capacitance CON Room Turn On Time tON Turn Off Time tOFF Break Before Make Time VNO or VNC = 1.5 V, RL = 300 , CL = 35 pF 7 Room nS pC -62 dB -69 29 pF 85 Power Supply Positive Supply Range V+ Negative Supply Current I+ 1.8 3.3 V 1.0 µA VIN = 0 or V+ 0.01 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 431-2288 www.protekanalog.com 95040 Rev.3. 10/11 NOT FOR USE IN LIFE SUPPORT SYSTEMS 2 PA2011 ANALOG PRODUCTS DIVISION Low RDSON SPDT Analog Switch. Specifications V+ = 3.0V Test Conditions unless otherwise specified: V+ = 3.0V±10%, VIN = 0.4 V or 2.0V Parameter Symbol Test Conditions Temp Min Typ Max Unit VCC V Analog Switch Full VNO,VNC, VCOM Analog Signal Range On-Resistance RON RON Matching ∆RON RON Flatness RON(FLAT) IOFF(NO) or IOFF(NC) Switch Off Leakage Current ICOM(OFF) Channel On Leakage Current ICOM(ON) 0.0 Room Full 1.8 VCC = 2.7V, VCOM = 0.9V- 1.5V INO , INC = 50mA, 0.2 0.2 V+ = 3.3 V, VNO, VNC= 1.0 V/3.0 V, VCOM = 3.0 V/1.0 V V+ = 3.3 V, VNO, VNC = VCOM = 1.0V/3.0 V 2.7 2.9 Ω 0.5 Room Full -1 -10 -1 -10 Room Full -1 -10 -1 -10 Room Full -1 -10 -1 -10 1.5 nA Digital Control Input High Voltage VINH Full Input Low Voltage VINL Full Input Capacitance Cin Full IINL or IINH Input Current VnA VIN = 0 or V+ Full 0.4 4 1 pF 1 µA Dynamic Characteristics Room Full 45 75 77 Room Full 29 59 62 Room Full 16 Turn On Time tON Turn Off Time tOFF Break Before Make Time tBBM Charge Injection QINJ Off Isolation OIRR Crosstalk XTALK Room NO, NC OFF Capacitance CNO(off) CNC(off) Room Chanel On Capacitance CON VNO or VNC = 2.0 V, RL = 300 , CL = 35 pF CL = 1 nF, VGEN = 0 V, RGEN = 0 Room 2 Room pC -62 RL = 50 , CL = 5 pF, f = 1 MHz VIN = 0 or V+, f = 1 MHz nS dB -69 28 pF Room 84 Power Supply Positive Supply Range V+ 1.8 3.3 V VIN = 0 or V+ Negative Supply I+ 0.01 1.0 Current Notes: 1. Room = 25 °C, Full = as determined by the operating suffix. 2. Typical values are for design aid only, not guaranteed nor subject to production testing. 3. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 4. Guarantee by design, not subjected to production test. 5. VIN = input voltage to perform proper function. 6. Guaranteed by 5 V leakage testing, not production tested. 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 431-2288 www.protekanalog.com 95040 Rev.3. 10/11 NOT FOR USE IN LIFE SUPPORT SYSTEMS µA 3 PA2011 Low RDSON SPDT Analog Switch. ANALOG PRODUCTS DIVISION Typical Characteristics TA = 25 °C, unless otherwise noted 6 6 A: 85 °C B: 25 °C C: - 40 °C 5 5 4 4 r ON – On-Resistance (Ω ) r ON – On-Resistance (Ω ) T = 25 °C V+ = 2.0 V IS = 20 mA 3 2 V+ = 3.0 V IS = 50 mA V+ = 3.3 V IS = 100 mA 1 V+ = 2.0 V IS = 20 mA A B 3 C V+ = 3.0 V IS = 50 mA A B 2 V+ = 3.3 V IS = 100 mA A B C C 1 0 0 0 1 2 3 4 5 0 6 1 2 VCOM – Analog Voltage (V) 3 4 5 6 VCOM – Analog Voltage (V) rON vs. VCOM and Supply Voltage rON vs. Analog Voltage and Temperature 10000 10 mA V+ = 3.3 V V+ = 3.3 V VIN = 0 V 1 mA 1000 100 µA I+ – Supply Current (A) I+ – Supply Current (nA) 10 µA 100 10 1 1 µA 100 nA 10 nA 1 nA 100 pA - 60 - 40 - 20 0 20 40 60 80 100 100 1k 10 k 100 k 1M 10 M Temperature (°C) Supply Current vs. Temperature Supply Current vs. Input Switching Frequency 250 10000 V+ = 3.3 V 200 V+ = 3.3 V 150 1000 Leakage Current (pA) Leakage Current (pA) 100 ION(off)/INC(off) 100 100 M Input Switching Frequency (Hz) ICOM( on) ICOM(off) 10 ICOM(off) 50 ICOM(on) 0 - 50 ION(off)/INC(off) - 100 - 150 - 200 1 - 250 - 60 - 40 - 20 0 20 40 60 80 Temperature (°C) Leakage Current vs. Temperature 100 0 1 2 3 NOT FOR USE IN LIFE SUPPORT SYSTEMS 5 Leakage vs. Analog Voltage 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 431-2288 www.protekanalog.com 95040 Rev.3. 10/11 4 VCOM, VNO , VNC, – Analog Voltage (V) 4 PA2011 Low RDSON SPDT Analog Switch. ANALOG PRODUCTS DIVISION Typical Characteristics TA = 25 °C, unless otherwise noted 10 90 0 tON V+ = 2 V LOSS 10 70 60 tON V+ = 3 V 50 40 tOFF V+ = 2 V tON V+ = 3.3 V 30 tOFF V+ = 3.3 V tOFF V+ = 3 V 20 Loss, OIRR, X TALK (dB) t ON / t OFF – Switching Time (ns) 80 20 30 40 XTALK 50 OIRR 60 70 10 V+ = 3.3 V RL = 50 80 0 - 60 90 - 40 - 20 0 20 40 60 80 100 100 K 1M 10 M Temperature (°C) 1G Insertion Loss, Off-Isolation, Crosstalk vs.Frequency Switching Time vs. Temperature and Supply Voltage 3.0 30 2.5 20 Q – Charge Injection (pC) VT – Switching Threshold (V) 100 M Frequency (Hz) 2.0 1.5 1.0 V+ = 2 V V+ = 3.3 V 10 0 V+ = 3 V 10 20 0.5 30 0.0 0 1 2 3 4 5 V+ – Supply Voltage (V) 6 7 Switching Threshold vs. Supply Voltage 0 1 2 3 4 NOT FOR USE IN LIFE SUPPORT SYSTEMS 6 VCOM – Analog Voltage (V) Charge Injection vs. Analog Voltage 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 431-2288 www.protekanalog.com 95040 Rev.3. 10/11 5 5 PA2011 Low RDSON SPDT Analog Switch. ANALOG PRODUCTS DIVISION Test Circuits V+ +3V Logic Input V+ NO or NC Switch Input 0V Switch Output COM VOUT RL 300 GND 0.9 x VOUT Switch Output IN Logic Input tr < 5 ns tf < 5 ns 50% CL 35 pF 0V tON tOFF 0V Logic "1" = Switch On Logic input waveforms inverted for switches that have the opposite logic sense. CL (includes fixture and stray capacitance) VOUT = VCOM RL R L + R ON Figure 1. Switching Time V+ Logic Input V+ tr <5 ns tf <5 ns 0V COM NO VNO 3V VO NC VNC RL 300 IN CL 35 pF VNC = VNO 90% VO Switch Output GND 0V tD tD CL (includes fixture and stray capacitance) Figure 2. Break-Before-Make Interval V+ Rgen VOUT V+ COM NC or NO VOUT VOUT + IN Vgen CL IN On 3V Off On GND Q = VOUT x CL IN depends on switch configuration: input polarity determined by sense of switch. Figure 3. Charge Injection 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 431-2288 www.protekanalog.com 95040 Rev.3. 10/11 NOT FOR USE IN LIFE SUPPORT SYSTEMS 6 PA2011 Low RDSON SPDT Analog Switch. ANALOG PRODUCTS DIVISION Test Circuits V+ 10 nF V+ COM IN COM 0V, 2.4 V NC or NO VNC/ NO Off Isolation = 20 log RL GND VCOM Analyzer Figure 4. Off-Isolation V+ 10 nF V+ COM Meter IN 0 V, 2.4 V NC or NO GND HP4192A Impedance Analyzer or Equivalent f = 1 MHz Figure 5. Channel Off/On Capacitance 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 431-2288 www.protekanalog.com 95040 Rev.3. 10/11 NOT FOR USE IN LIFE SUPPORT SYSTEMS 7 PA2011 Low RDSON SPDT Analog Switch. ANALOG PRODUCTS DIVISION Package Outline and Dimensions DFN-6 P1 Dim P1 P2 P3 L1 L2 L3 P G1 G2 p L1 L2 P2 G2 MILLIMETERS MIN MAX 1.5 1.7 1.5 1.7 0.45 0.65 0.23 0.27 0.20 0.30 0.01 0.09 0.50 0.50 0.90 1.10 0.38 0.43 INCHES MIN MAX 0.060 0.066 0.060 0.066 0.018 0.026 0.009 0.012 0.008 0.012 0.001 0.003 0.020 0.020 0.035 0.043 0.013 0.017 G1 TOP VIEW BOTTOM VIEW 1.1mm 0.50mm L3 P3 0.50mm SIDE VIEW 1.8mm 0.33mm 0.48mm Recommended Land Pattern Tape and Reel Specifications (Dimensions in mm) Reel Dia A0 B0 K0 D E F W P0 P2 P t-max 178 (7”) 1.80±0.10 1.80±0.10 0.80±0.10 1.50±0.10 1.75±0.10 3.50±0.05 8.00±0.30 4.00±0.10 2.00±0.05 4.00±0.10 0.25 P0 P2 D t 10 Pitches Cumulative Tolerance on Tape± 0.2 E Pin 1 indicated by Dot Top cover tape A0 F W K0 B0 P 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 431-2288 www.protekanalog.com 95040 Rev.3. 10/11 NOT FOR USE IN LIFE SUPPORT SYSTEMS 8 PA2011 Low RDSON SPDT Analog Switch. ANALOG PRODUCTS DIVISION Package Outline and Dimensions SC70-6 Lead Dim MILLIMETERS MIN MAX A 1.90 2.15 B 1.15 1.35 C 0.80 1.00 D 0.15 0.30 E 0.65 BSC F 1.30 BSC G 0.80 1.10 J 0.08 0.25 K 2.00 2.20 L 0 0.10 M 0.26 0.46 LAND PATTERN 1 0.50 2 1.30 3 0.65 4 1.72 5 0.60 6 1.11 7 2.33 D E 6 4 0°-8° K 3 L 1 J M B F End View A Top View 4 C G INCHES MIN MAX 0.074 0.084 0.045 0.055 0.031 0.040 0.006 0.012 0.0255 BSC 0.0512 BSC 0.031 0.043 0.003 0.010 0.078 0.086 0 0.004 0.010 0.018 0.020 0.051 0.026 0.068 0.024 0.044 0.092 2 3 1 Side View 5 6 7 Recommended Land Pattern Tape and Reel Specifications (Dimensions in mm) Reel Dia A0 B0 K0 D E F W P0 P2 P t-max 178 (7”) 2.25±0.10 2.34±0.10 1.22±0.10 1.50±0.10 1.75±0.10 3.50±0.05 8.00±0.30 4.00±0.10 2.00±0.05 4.00±0.10 0.25 P0 P2 D t 10 Pitches Cumulative Tolerance on Tape± 0.2 E Pin 1 indicated by Dot Top cover tape A0 F W K0 B0 P Life Support Policy PROTEK ANALOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF PROTEK DEVICES. 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (602) 431-2288 www.protekanalog.com 95040 Rev.3. 10/11 NOT FOR USE IN LIFE SUPPORT SYSTEMS 9