THT POWER INDUCTORS Toroid - Vertical, Low Profile and KlipMount™ Available in vertical, low profile and KlipMount™ SMPS averaging filter Characterized for general purpose use and ripple filters Single-layer designs Can be used as differential mode inductors in EMI filters3 Electrical Specifications @ 25°C — Operating Temperature -40°C to 130°C REFERENCE OPERATING VALUES DESIGN CONTROL VALUES 4 Inductance Low Profile Inductance1 Energy 20kHz Coil Klip* Lead IDC ETOP DCR5 Part Typical Storage No DC (µH) Test mV Size Mount Diameter (Ω MAX) (AMPS) (V-µSec) Code Package (In) ±.003 Number (µH) (µJ) ±20% No DC2 — 20 2.0 52 40 32.8 33 .060 H — .020 — 25 2.6 30 85 20.7 22 .043 A KM1 .020 PE-92401 50 2.6 50 169 45.7 45 .071 B KM2 .020 PE-92402 100 2.6 90 338 94.1 90 .100 C KM3 .020 — 35 2.6 55 118 28.4 36 .037 B KM2 .025 PE-92404 70 3.0 85 315 61.0 73 .052 C KM3 .025 PE-92405 145 3.0 140 653 141.8 140 .087 D KM4 .025 — 285 3.0 300 1283 264.1 340 .140 E KM5 .025 — 450 3.0 425 2025 436.3 500 .200 F — .025 PE-92408 67 3.6 130 648 90.7 110 .045 D KM4 .032 — 165 4.0 240 1320 152.0 260 .070 E KM5 .032 — 270 4.0 350 2160 263.9 400 .100 F — .032 — 40 4.0 70 320 37.9 57 .027 C KM3 .032 — 22 5.0 44 275 20.3 37 .020 G — .032 PE-92412 100 5.0 200 1250 90.7 180 .034 E KM5 .042 — 170 5.0 300 2125 159.7 310 .050 F — .042 PE-92414 35.6 5.0 100 688 55.6 88 .023 D KM4 .042 — 95 7.0 225 2328 96.0 200 .025 F — .051 PE-92416 55 7.0 150 1348 49.1 100 .017 E KM5 .051 — 55 10.0 175 2750 55.9 120 .013 F — .064 *Parts available with KlipMount option can be ordered by adding a "K" suffix to the part number (i.e. PE-92100K). Vertical6 Part Number PE-51591 PE-92100 PE-92101 PE-92102 PE-92103 PE-92104 PE-92105 PE-92106 PE-92107 PE-92108 PE-92109 PE-92110 PE-92111 PE-51590 PE-92112 PE-92113 PE-92114 PE-92115 PE-92116 PE-92117 Inductance vs. Operating ET Max. Operating ET vs. Frequency (at reference ET) (at reference IDC) (at reference IDC) 2.00 1.75 Temp. Rise >40°C 1.50 1.25 1.00 .75 .50 .25 0 .25 .50 .75 1.00 1.25 1.50 OPERATING DC CURRENT REFERENCE IDC 2.00 1.75 Temp. Rise >40°C 1.50 1.25 1.00 .75 .50 .25 0 .25 .50 .75 1.00 1.25 1.50 OPERATING ET REFERENCE ET OPERATING ET FOR 40°C TEMP. RISE REFERENCE ET Inductance vs. DC Current INDUCTANCE AT OPERATING ET INDUCTANCE AT REFERENCE ET INDUCTANCE AT OPERATING IDC REFERENCE IDC Relationships Between Reference and Operating Conditions 2.00 1.75 1.50 1.25 1.00 .75 .50 .25 0 20 30 40 50 60 70 80 90 100 OPERATING FREQUENCY — kHz USA 858 674 8100 • UK 44 1483 401 700 • France 33 3 84 35 04 04 • Singapore 65 6287 8998 • Shanghai 86 21 54643211 / 2 • China 86 769 85538070 • Taiwan 886 3 4641811 www.pulseeng.com P635.A (4/06) THT POWER INDUCTORS Toroid - Vertical, Low Profile and KlipMount™ Mechanicals • • • • Base material meets flammability requirements of UL 94V-0 Mechanically rigid mount PC board — automatic insertability Lowest cost A Standard Package B Maximum C D KlipMount™ Package C E Typical KM-1 .340 8,64 .580 14,73 .650 16,51 .29 7,37 .110 2,79 KM-2 .450 11,43 .650 16,51 .700 17,78 .325 8,26 .150 3,81 KM-3 .450 11,43 .850 21,59 .950 24,13 .415 10,54 .150 3,81 KM-4 .620 15,50 .970 24,64 1.10 27,94 .475 12,07 .225 5,72 KM-5 .700 17,78 1.30 33,02 1.40 35,56 .625 15,88 .250 6,35 .130 ± .020 3,30 ,508 E 2E D B A SCHEMATIC 1 Note: Units with large wire sizes may exceed B dimension. KLIPMOUNT™ is a trademark of Pulse Engineering, Inc. Dimensions: Inches mm Coil Size A B C D E F G H 2 Unless otherwise specified, all tolerances are ± .010 0,25 P (MAX) .550 13,97 .700 17,78 .850 21,59 1.050 26,67 1.400 35,56 1.650 41,91 .850 21,59 .640 16,26 N (MAX) .250 6,35 .380 9,65 .410 10,41 .550 13,97 .700 17,78 .700 17,78 .330 8,38 .280 7,11 Vertical Package L (+.125/-.025) M K .375 9,53 .375 9,53 .375 9,53 .375 9,53 .375 9,53 .375 9,53 .875 22,23 .875 22,23 .180 4,57 .280 7,11 .280 7,11 .400 10,16 .500 12,7 .500 12,7 .330 8,38 .280 7,11 — .530 .050 ± 13,46 1,27 .720 .050 ± 18,29 1,27 .840 .020 ± 21,24 0,51 1.100 .100 ± 27,94 2,54 NOTES: 1 Typical Inductance occurs at IDC and ETOP values shown. 2. Design control test voltage is critical. Inductance increases with voltage. 3. For line filter applications, RMS line current is limited to specified reference DC Current. P L M N Low Profile Package PE-924XX — .375 ± .125 9,58 3,18 — — P K 4. LI2 rating is the ability of the inductor to store energy. 2 5. DCR for vertical part measured close to coil. Add 10% more for low profile part. 6. RoHS compliant parts are available. Order RoHS compliant parts by adding the suffix "NL" to the part number (i.e. PE-51591 becomes PE-51591NL). For More Information: Pulse Worldwide Headquarters Pulse Northern Europe Pulse Southern Europe Pulse Pulse North China China Headquarters Room 1503 12220 World Trade Drive San Diego, CA 92128 U.S.A. www.pulseeng.com TEL: 858 674 8100 FAX: 858 674 8262 3 Huxley Road Surrey Research Park Guildford, Surrey GU2 5RE United Kingdom TEL: 44 1483 401700 FAX: 44 1483 401701 Zone Industrielle F-39270 Orgelet France TEL: 33 3 84 35 04 04 FAX: 33 3 84 25 46 41 No. 1 Industrial District Changan, Dongguan China TEL: 86 769 85538070 FAX: 86 769 85538870 XinYin Building No. 888 YiShan Road Shanghai 200233 China TEL: 86 21 54643211/2 FAX: 86 21 54643210 Pulse South Asia Pulse North Asia 150 Kampong Ampat #07-01/02 KA Centre Singapore 368324 No. 26 Kao Ching Road Yang Mei Chen Taoyuan Hsien Taiwan, R. O. C. TEL: 886 3 4641811 FAX: 886 3 4641911 TEL: 65 6287 8998 FAX: 65 6280 0080 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2006. Pulse Engineering, Inc. All rights reserved. www.pulseeng.com P635.A (4/06)