SF2060B ® • • • • • Designed for SDARS Receiver IF Application Low Insertion Loss 5.0 X 7.0 mm Surface-Mount Case Differential Input and Output Complies with Directive 2002/95/EC (RoHS) 115.18 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC -40 to +85 °C Storage Temperature Range Suitable for lead-free soldering - Max Soldering Temperature SMP-03 260°C for 30 s Electrical Characteristics Characteristic Center Frequency (Fc variation must also be accounted for with an extra ±94 kHz due to crystal variation ±40 ppm at the LO frequency) Insertion Loss (all BW specifications are a function of FC variation) Amplitude Ripple (p-p) between (Fc-6.250 MHz to Fc-4.3925 MHz) Amplitude Ripple (p-p) between (Fc-4.3925 MHz to Fc-2.535 MHz) Amplitude Ripple (p-p) between (Fc-2.535 MHz to Fc-0.025 MHz) Amplitude Ripple (p-p) between (Fc+0.025 MHz to Fc+2.535 MHz) Amplitude Ripple (p-p) between (Fc+2.5350 MHz to Fc+4.3925 MHz) Amplitude Ripple (p-p) between (Fc+4.3925 MHz to Fc+6.250 MHz) Pass Bandwidth of -1.5 dB Pass Bandwidth of -3 dB Low side Attenuation Fc < (Fc -16.5 MHz) Low side Attenuation between: (Fc -16.5 MHz)....(Fc -10.5 MHz) High side Attenuation between: (Fc +9.0 MHz)....(Fc +16.5 MHz) (-15~85°C) High side Attenuation between: (Fc +9.0 MHz)....(Fc +16.5 MHz) (-40~-15°C) High side Attenuation Fc > (Fc +16.5 MHz) Temperature Coefficient of Frequency Delay Ripple (p-p) between (Fc -6.250 MHz to Fc-4.3925 MHz) SAT1A (Fc -4.3925 MHz to Fc-2.535 MHz) SAT2A (Fc -2.535 MHz to Fc-0.025 MHz) TERA (Fc +0.025 MHz to Fc+2.535 MHz) TERB (Fc +2.535 MHz to Fc+4.3925 MHz) SAT2B (Fc +4.3925 MHz to Fc+6.25 MHz) SAT1B Operating Temperature Range Differential Input and Output Impedance Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 Notes: 1. 2. 3. 4. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. The design, manufacturing process, and specifications of this filter are subject Sym Notes fC 1 Min Typ Max 115.18 14 MHz 16.2 1.65 1.5 1.5 1.6 1.5 1.5 13.5 14.5 1 6 dB dB MHz 34 32 24 18 33 TA Units dB -18 150 180 120 120 120 120 +85 ppm/°C ns -40 °C L & C Match to 200 ohms SMP-03 7 x 5 mm Nominal Footprint RFM SF2060B YYWWS to change. Tape and Reel Standard Per ANSI / EIA 481. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. 8. ©Copyright 1999, RF Monolithics Inc. Electrostatic Sensitive Device. Observe precautions for handling. 5. 6. 7. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF2060B-020907 Page 1 of 6 115.18 MHz SAW Filter CH1 S 21 log MAG 10 dB/ REF -14 dB 28 Jun 2005 13:28:38 1_: 0 dB SF2060B DEMO -3 DB PASSBAND PRm 0.000 000 MHz REF=1 BW: 14.458 108 MHz 1 Cor cent: 115.170504 MHz Q: 7.9658 2 3 1_ loss: 4 -14.063 dB CENTER 115.180 000 MHz CH1 S 21 SPAN 40.000 000 MHz log MAG 1 dB/ REF -14.8 dB 28 Jun 2005 13:27:09 3_:-.6919 dB SF2060B DEMO AMP. RIPPLE AND DELAY PRm 12.500 000 MHz REF=2 mean:-14.269 dB Cor 3 s.dev: .2391 dB p-p: 1.053 dB 2 CH2 S 21 delay 50 ns/ REF 700 ns 3_ -44.365 ns 12.500 000 MHz REF=2 PRm mean: 702.56 ns Cor s.dev: 11.786 ns 3 p-p: 64.621 ns 2 Smo CENTER 115.180 000 MHz RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SPAN 40.000 000 MHz E-mail: [email protected] http://www.rfm.com SF2060B-020907 Page 2 of 6 115.18 MHz SAW Filter CH1 S 11 log MAG 5 dB/ 28 Jun 2005 13:22:58 1_:-26.965 dB REF 0 dB SF2060B DEMO RETURN LOSS PRm 115.180 000 MHz 2_:-7.56 dB 108.93 MHz Cor 3_:-6.3919 dB 121.43 MHz 3 2 1 CH2 S 22 log MAG 5 dB/ REF 0 dB 1_ -25.658 dB 115.180 000 MHz PRm 2_ -6.6543 dB 108.93 MHz Cor 3_ -7.6705 dB 121.43 MHz 2 3 1 CENTER 115.180 000 MHz CH1 S 11 1 U FS SPAN 40.000 000 MHz 1_: 45.77 28 Jun 2005 13:20:47 -820.31 m 1.6845 nF SF2060B DEMO MATCHED TO 200 OHMS PRm 115.180 000 MHz Cor 1 CH2 S 22 1 U FS 1_ 46.891 3.9805 5.5002 nH 115.180 000 MHz PRm Cor CENTER 115.180 000 MHz RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. 1 SPAN 40.000 000 MHz E-mail: [email protected] http://www.rfm.com SF2060B-020907 Page 3 of 6 115.18 MHz SAW Filter SF2060B DEMO SCHEMATIC P9 P8 0 P7 L1 L3 TX2 TX1 P10 P6 100 nH 91 nH C1 C2 SF2060B 27 pF 0 27 pF L2 L4 P1 P5 1:4 4:1 100 nH P2 P3 P4 91 nH 0 0 20.0 mm 47.3 mm RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF2060B-020907 Page 4 of 6 115.18 MHz SAW Filter SMP-03 Case 10-Terminal Ceramic Surface-Mount Case 7 x 5 mm Nominal Footprint Case Dimensions Dimension A B C D E H J K P Recommended PCB Footprint Min 6.80 4.80 .47 2.41 0.87 4.87 2.87 1.14 mm Nom 7.00 5.00 1.65 0.60 2.54 1.0 5.00 3.00 1.27 Max 7.20 5.20 2.00 .73 2.67 1.13 5.13 3.13 1.40 Min 0.268 0.189 0.019 0.095 0.034 0.192 0.113 0.045 Inches Nom 0.276 0.197 0.065 0.024 0.100 0.039 0.197 0.118 0.050 Max 0.283 0.205 0.079 0.029 0.105 0.044 0.202 0.123 0.055 Materials Solder Pad Termination Au plating 30 - 60 µinches (76.2-152 µm) over 80200 µinches (203-508 µm) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 µinches Thick Body Al2O3 Ceramic Pb Free Electrical Connections Connection Port 1 Port 2 Terminals Input or Return 10 Return or Input 1 Output or Return 5 Return or Output 6 Ground All others Single Ended Operation Return is ground Differential Operation Return is hot C B E H H A J D P K RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF2060B-020907 Page 5 of 6 115.18 MHz SAW Filter Tape and Reel Specifications 100 REF. "B" REF. “B “ Nominal Size Quantity Per Reel Inches millimeters 7 178 500 13 330 2000 See Detail "A" 13. 0 12.0 16.0 .2 20 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 5.5 mm Bo 7.5 mm Ko 2.0 mm Pitch 8.0 mm W 16.0 mm PIN #1 USER DIRECTION OF FEED RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF2060B-020907 Page 6 of 6