RFM SF2094B

SF2094B
•
•
•
•
Low Insertion Loss
5.0 X 7.0 mm Surface-Mount Case
Differential Input and Output or Single Ended Input and Output
Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Rating
380.00 MHz
SAW Filter
Pb
Value
Units
Maximum Incident Power in Passband
+13
dBm
Max. DC voltage between any 2 terminals
30
VDC
Storage Temperature Range
-40 to +85
Suitable for lead-free soldering - Max Soldering Temperature
°C
260°C for 30 s
SMP-03
Electrical Characteristics
Characteristic
Nominal Center Frequency
Insertion Loss
3 dB Bandwidth
Passband Variation
Group Delay Variation
Reflected
Return Loss
Triple Transit
After 1-2us
After 2-3us
After >3us
Ultimate Rejection
Maximum Peak RF Input Power
Maximum RF Input Power Over Life
Temperature Range
Frequency Temperature Coefficient
Case Style
Lid Symbolization (YY=year, WW=week, S=shift)
Sym
Notes
Min
Typ
Max
Units
fC
1
379.9
380.00
380.1
13.5
MHz
dB
MHz
dB
dB
nsec
BW3
4.0
0.5
2.3
250
CF ±1.7 MHz
CF ±1.85 MHz
CF ±1.7 MHz
1.5
3.5
10
35
20
35
45
DC to 180 MHz
180 to 284 MHz
284 to 340 MHz
340 to 376.15 MHz
383.4 to 580 MHz
580 to 870 MHz
30
40
50
36
36
30
Operating
Storage
-15
-40
FTC
dB
dB
13
10
85
85
0.032
SMP-03 7 x 5 mm Nominal Footprint
RFM SF2094B YYWWS
dBm
dBm
°C
ppm/°C2
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 Ω and measured with 50 Ω network analyzer.
Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
The design, manufacturing process, and specifications of this filter are subject to change.
The turnover temperature, TO, is the temperature of maximum (or turnover) frequency, fo. The nominal frequency at any case temperature, Tc, may be
calculated from: f=fo[1-FTC(To-Tc)2].
Tape and Reel Standard ANSI / EIA 481.
Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
©Copyright 1999, RF Monolithics Inc.
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 1 of 12
SF2094B - 4/2/08
SMP-03 Case
10-Terminal Ceramic Surface-Mount Case
7 x 5 mm Nominal Footprint
Case Dimensions
mm
Dimension
A
B
C
D
E
H
J
K
P
Recommended PCB Footprint
Inches
Min
Nom
Max
Min
Nom
Max
6.80
4.80
1.50
.47
2.41
0.87
4.87
2.87
1.14
7.00
5.00
1.65
0.60
2.54
1.0
5.00
3.00
1.27
7.20
5.20
2.00
.73
2.67
1.13
5.13
3.13
1.40
0.268
0.189
0.059
0.019
0.095
0.034
0.192
0.113
0.045
0.276
0.197
0.065
0.024
0.100
0.039
0.197
0.118
0.050
0.283
0.205
0.079
0.029
0.105
0.044
0.202
0.123
0.055
Materials
Solder Pad
Termination
Au plating 30 - 60 µinches (76.2-152 µm) over 80200 µinches (203-508 µm) Ni.
Lid
Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 µinches Thick
Body
Al2O3 Ceramic
Pb Free
Electrical Connections
Connection
Single Ended Operation
Terminals
Input
10
Output
Differential Operation
5
Input
1, 10
Output
5, 6
Ground
All others
RFM Matching Circuit Illustrated Seperately
C
B
E
H
H
A
J
D
P
K
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 2 of 12
SF2094B - 4/2/08
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 3 of 12
SF2094B - 4/2/08
Supplier
Size
Q
Value
Tolerance
Coilcraft
0805
60
47 nH
5%
Coilcraft
0805
60
39 nH
5%
Coilcraft
0805
60
6 nH
5%
Presidio
0603
-
18 pF
5%
Presidio
0603
-
8.2 pF
5%
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 4 of 12
SF2094B - 4/2/08
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 5 of 12
SF2094B - 4/2/08
Supplier
Size
Q
Value
Tolerance
Coilcraft
0805
40
39 nH
5%
Coilcraft
0805
38
56 nH
5%
Presidio
0603
-
2.2 pF
5%
Presidio
0603
-
2.7 pF
5%
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 6 of 12
SF2094B - 4/2/08
COMPONENT ORIENTATION and DIMENSIONS
4.0 mm ±0.1
1.5 mm +0.1
-0.0
2.0 mm ±0.1
1.75 mm ±0.1
PIN #1
W
(CARRIER TAPE SIZE)
7.5 mm ±0.1
BO
1.5 mm +0.3
-0.0
P
(PITCH)
AO
USER DIRECTION OF FEED
COVER TAPE SIZE
2.15 mm ±0.2
KO
COVER TAPE
0.32 mm ±0.3
Carrier Tape Dimensions
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Ao
5.5 mm
±0.1
Bo
7.5 mm
±0.1
Ko
2.0 mm
±0.1
Pitch
8.0 mm
±0.1
W
16.0 mm
±0.3
Page 7 of 12
SF2094B - 4/2/08
Leader and Trailer specifications (Based upon EIA-481)
Dimensions of the leader and trailer
7 Inch Reel Quantity 500
A
Symbol
Dimension
178
N
+0
-4
60
C
±1
13
D
+0.5
-0.2
20.2
B
+1.5
-0
2
W1
±0.5
16.4
±0.5
16.4
W2
+2
-0
22.4
+2
-0
22.4
MAX
13 Inch Reel Quantity 2000
A
Symbol
Dimension
330
N
+0
-4
100
C
±2
13
D
+0.5
-0.2
20.2
B
+1.5
-0
2
W1
W2
MAX
Dimensional drawing of the reel
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 8 of 12
SF2094B - 4/2/08
Additional items
(1) Cover tape peeling strength
The cover tape shall be adhered evenly to the carrier tape along both sides in the pulling direction.
The cover tape peeling strength shall be as follows for an angle between the cover tape and the pulling
direction of 165° to 180° (see the figure) and a peeling speed of 300mm/min. ±10mm/min.
[EIA-481] 0.1N to 1.3N for a tape width of 12 to 56mm
Fixing method
1. Insert the tip of the carrier tape into the groove.
2. Fix the tip of the cover tape with adhesive tape.
Tape material
(1) Carrier tape [anti-charging treatment: carbon used] Surface resistivity: 1 x 108 or less
Material: Polystyrene or Polycarbonate
(2) Cover tape material: Polyester (anti-charging treated) Surface resistivity: 1 x 1012 or less
t = 50 to 100µm width = 13.3mm
Warranty periods
Cover tape peeling strength and mounting performance of stored components.
2-1. Cover tape peeling strength: One year after delivery (Peeling strength: 0.1N to 1.3N)
Number of missing components
There shall not be two or more consecutive missing components. Also, the maximum number of missing
components shall be the larger of one piece or 0.1%.
Storage environment
Keep the product on which taping has been performed to a temperature below 40°C and a humidity within
80% RH. Do not subject in the direct sun.
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 9 of 12
SF2094B - 4/2/08
Labeling
The following items are labeled on the surface of a reel.
Product Part Number, Date Code, Quantity
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 10 of 12
SF2094B - 4/2/08
Package for Shipment
7 Inch
Reel
13 Inch
Reel
Quanity
Per Reel
Number Reels
Per Carton
External Caton
Dimensions
Reel
Weight
Shipping Carton
Weight
Total
Weight
500
4
254 x 254 x 127 mm
10 x 10 x 5 inches
896 g
448 g
1344 g
500
10
254 x 254 x 203 mm
10 x 10 x 8 inches
2240 g
448 g
2688 g
Quanity
Per Reel
Number Reels
Per Carton
External Caton
Dimensions
Reel
Weight
Shipping Carton
Weight
Total
Weight
2000
2
356 x 356 x 102 mm
14 x 14 x 4 inches
1288 g
448 g
1736 g
2000
4
356 x 356 x 178 mm
14 x 14 x 7 inches
2576 g
448 g
3024 g
2000
8
356 x 356 x 356 mm
14 x 14 x 14 inches
5152 g
448 g
5600 g
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 11 of 12
SF2094B - 4/2/08
RFM Qualification and Reliability Test
Test
Standard
Test Parameters
Measurement Criteria
Results
Within Electrical & Hermetic Spec.
(Note 1)
Pass
1
Life at
Elevated
Temperature
MIL-STD-202
Method 108
Condition C
1,000 Hours
125°C
Unbiased
2
Temperature
Cycling
JESD22
Method JA-104
Air-to-Air
-55 ×Cto +125 ×C
20 min. Dwell
1,000 cycles
Pass
3
Vibration,
Variable
Frequency
MIL-STD-883
Method 2007
Condition B
50g Max.
4 Cycles, 3 Axis
20 Hz to 2 kHz to
20 Hz
Pass
4
Mechanical
Shock
MIL-STD-883
Method 2002
Condition B
1,500g Max.
5 Shocks
±3 Axis
Pass
5
Destructive
Bond
Strength
MIL-STD-883
Method 2011
Condition C
Wire Bond Pull
Strength
2.0 grams (After Seal)
Pass
6
Die Shear
Strength
MIL-STD-883
Method 2019
Shear Strength
0.6 kg
(Strength/area limit in
development)
Pass
7
Solderability
(Note 2)
J-STD-002
Method B
8 hr. steam age
245 × C solder
temperature
5 second dwell
>95% wetted surface
Pass
8
Physical
Dimensions
JESD22
Method JB-100
Critical
Dimensions
Within specifications
Pass
9
Temperature
Characteristics
RFM Procedure
Frequency over
Temperature
Within specifications
Pass
10
Terminal
Strength
(Note 2)
MIL-STD-833
Method 2004
Condition A & D
Cond. A-Lead
Tension
Cond. B -Pad
Adhesionr 24
8 oz. - 30 sec.
Visual Requirements & meets
Hermetic Spec.
Pass
11
Resistance to
Solvents
MIL-STD-883
Method 2015
Solvents a, b, d
Visual Requirements
Pass
12
Steady State
Life
MIL-STD-883
Method 1005
1,000 Hours
Max. Operating
Temperature
Rated Voltage
Within Electrical & Hermetic Spec.
(Note 1)
Pass
13
Internal WaterVapor Content
MIL-STD-883
Method 1018
< 5,001 PPM
Pass
14
Constant
Acceleration
MIL-STD-883
Method 2001
Y1 Direction
30,000g
Within Electrical & Hermetic Spec.
(Note 1)
Pass
15
Substrate
Attach Strength
MIL-STD-883
Method 2027
Tensile Strength of
Die Attachment
Custom per Device
Pass
www.RFM.com
E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 12 of 12
SF2094B - 4/2/08