SMA3117 Ordering number : EN8936A SANYO Semiconductors DATA SHEET SMA3117 Silicon MMIC Wideband Amplifier Features • • • • • • High Gain : Gp=33.5dB typ. @2.2GHz Wideband response : fu=3.0GHz Low current : ICC=22.7mA typ. High output power : Po(1dB)=5.7dBm Port impedance : input/output 50Ω Halogen free compliance Specifications Absolute Maximum Ratings at Ta=25°C Parameter Symbol Supply Voltage Conditions Ratings Unit VCC ICC 6 V 40 mA PD Topr 280 mW Operating Temperature --40 to +85 °C Storage Temperature Tstg --55 to +150 °C Circuit Current Allowable Power Dissipation Package Dimensions Product & Package Information unit : mm (typ) 7022A-018 • Package : MCPH6 • JEITA, JEDEC : SC-88, SC-70-6, SOT-363 • Minimum Packing Quantity : 3,000 pcs./reel 6 5 0 to 0.02 1 2 Marking TL 3 0.65 LG LOT No. 0.3 0.85 0.25 Packing Type : TL 4 LOT No. 0.07 SMA3117-TL-H 0.15 2.1 1.6 0.25 2.0 1 2 3 1 : VCC 2 : GND 3 : OUT 4 : GND 5 : GND 6 : IN 6 5 4 SANYO : MCPH6 http://www.sanyosemi.com/en/network/ 90512 TKIM/71311AM TKIM TC-00002627 No.8936-1/7 SMA3117 Recommended Operating Conditions at Ta=25°C Parameter Symbol Supply Voltage Ratings Conditions min VCC Topr Operating Ambient Temperature typ Unit max 4.5 5 5.5 V --40 +25 +85 °C Electrical Characteristics at Ta=25°C, VCC=5V, Zs=ZL=50Ω Parameter Symbol Circuit Current Ratings Conditions min ICC Power Gain Gp Isolation ISL Input Return Loss RLin Output Return Loss RLout Noise Figure NF Gain 1dB Compression Output Power *1 Po(1dB) Upper Limit Operating Frequency *1 fu typ max 18.5 22.7 28.0 f=1GHz 29.5 31.2 32.5 f=2.2GHz 30.5 33.5 35.5 f=1GHz 35.0 37.6 f=2.2GHz 34.0 36.5 f=1GHz 9.0 11.2 f=2.2GHz 4.5 6.0 f=1GHz 11.0 14.3 f=2.2GHz 12.0 16.3 dB 4.1 5.0 3.9 5.0 7.5 9.8 3.7 5.7 3dB down below flat gain at f=1GHz dB dB f=2.2GHz f=2.2GHz mA dB f=1GHz f=1GHz Unit 3.0 dB dBm GHz *1 : On evaluation board Note) Pay attention to handling since it is liable to be affected by static electricity due to the high frequency process adopted. Ordering Information Device Package Shipping memo MCPH6 3,000pcs./reel Pb Free and Halogen Free SMA3117-TL-H Test Circuit 100pF IN 6 5 4 1 2 3 100pF OUT 1000pF 100nH VCC Connect 2, 4 and 5 with GND. IT15580 No.8936-2/7 SMA3117 Evaluation Board IN OUT C1 C2 L1 C3 Symbol Value C1, C2 VCC C3 100pF 1000pF L1 100nH ICC -- VCC 30 Circuit Current, ICC -- mA 25 20 15 10 5 0 0 1 2 3 4 5 Circuit Voltage, VCC -- V 6 IT16522 Gp -- f 40 RLin -- f 0 35 V 5.0 Input Return Loss, RLin -- dB Power Gain , Gp -- dB 5.5V 5.5V 4.5V 30 25 0 1 2 Frequency, f -- GHz 3 4 IT16523 --5 5.0V 4.5V --10 --15 --20 --25 --30 0 1 2 Frequency, f -- GHz 3 4 IT16524 No.8936-3/7 SMA3117 ISL -- f Isolation, ISL -- dB --10 --20 --30 5.0V 4.5V 5.5V --40 --50 0 1 2 3 Output Power, Pout -- dBm Output Power, Pout -- dBm 0 --10 --20 --30 5.0 5.5V V --20 --25 0 1 --20 --10 Input Power, Pin -- dBm 4 IT16526 10 0 --10 --20 --50 --40 --20 --30 --10 Input Power, Pin -- dBm IT16527 S11 3 VCC=5V f=2.2GHz --30 --60 0 S Parameter (VCC=5V) 2 Pout -- Pin 20 10 --40 4.5V --15 Frequency, f -- GHz VCC=5V f=1GHz --50 --10 IT16525 Pout -- Pin --30 --60 --5 --30 4 Frequency, f -- GHz 20 RLout -- f 0 Output Return Loss, RLout -- dB 0 0 IT16528 S22 50 50 100 25 250 10 100 25 250 10 3GHz 10 0 2GHz 50 25 100 250 10 0 25 100 50 250 1GHz 2GHz 1GHz 3GHz --10 --250 --25 --10 --250 --25 --100 --50 IT16529 --100 --50 IT16530 No.8936-4/7 SMA3117 Embossed Taping Specification SMA3117-TL-H No.8936-5/7 SMA3117 Outline Drawing SMA3117-TL-H Land Pattern Example Mass (g) Unit 0.008 mm * For reference Unit: mm 2.1 0.6 0.4 0.65 0.65 No.8936-6/7 SMA3117 Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment. The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for new introduction or other application different from current conditions on the usage of automotive device, communication device, office equipment, industrial equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. Regarding monolithic semiconductors, if you should intend to use this IC continuously under high temperature, high current, high voltage, or drastic temperature change, even if it is used within the range of absolute maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a confirmation. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of September, 2012. Specifications and information herein are subject to change without notice. PS No.8936-7/7