SMA5101 Ordering number : ENA1839A SANYO Semiconductors DATA SHEET SMA5101 Silicon Monolithic Linear IC RF Double Balanced Mixer IC Features • • • Wide band : up to Ku band Low distortion : IIP3=20dBm (@ICC > 11mA) SMT, Ultra small package : 2.0×2.1×0.85mm • • • High conversion gain : --0.5dB (@450MHz) Low voltage available : 1.2V and above Halogen free compliance Specifications Absolute Maximum Ratings at Ta=25°C Parameter Symbol Collector-to-Base Voltage Collector-to-Emitter Voltage Emitter-to-Base Voltage Collector Current Max Power Dissipation Conditions Ratings Unit VCBO VCEO 8 V 6 V VEBO ICC 2 V 50 mA 280 mW Operating Temperature PC Topr --40 to +85 °C Storage Temperature Tstg --55 to +150 °C Package Dimensions Product & Package Information unit : mm (typ) 7022A-020 • Package : MCPH6 • JEITA, JEDEC : SC-88, SC-70-6, SOT-363 • Minimum Packing Quantity : 3,000 pcs./reel 6 5 0.15 Marking 0 to 0.02 1 2 0.3 0.85 1 6 2 5 TL 3 0.65 LD LOT No. 0.25 Packing Type : TL LOT No. 0.07 SMA5101-TL-H 4 2.1 1.6 0.25 2.0 3 1 : Base2 2 : Collector1 3 : Collector2 4 : Emitter2 5 : Emitter1 6 : Base1 4 SANYO : MCPH6 Equivalent Circuit 1 2 6 3 5 4 IT15506 http://www.sanyosemi.com/en/network/ 90512 TKIM/O0610AM TKIM TC-00002495 No. A1839-1/7 SMA5101 Recommended Operating Condition at Ta=25°C Parameter Symbol Supply Voltage Ratings Conditions min typ Unit max VC1E1 1.2 3 6 V VC2E1 1.2 3 6 V VC1E2 1.2 3 6 V VC2E2 1.2 3 6 V Electrical Characteristics at Ta=25°C Parameter Symbol Collector Cutoff Current Emitter Cutoff Current DC Current Gain Conversion Gain *1 Ratings Conditions min typ Unit max IC1B1O VC1B1=5V 1 μA IC2B1O VC2B1=5V 1 μA IC1B2O VC1B2=5V 1 μA IC2B2O VC2B2=5V 1 μA IE1B1O VE1B1=1V 1 μA IE2B1O VE2B1=1V 1 μA IE1B2O VE1B2=1V 1 μA IE2B2O VE2B2=1V 1 μA hFE1 VC1E1=1V, IC1E1=3mA 20 120 hFE2 VC2E1=1V, IC2E1=3mA 20 120 hFE3 20 120 hFE4 VC1E2=1V, IC1E2=3mA VC2E2=1V, IC2E2=3mA 20 120 Gc VCC=5V, ICC=6mA, f(RF)=450MHz, f(LO)=500MHz, --0.5 dB P(RF)=--15dBm, P(LO)=--6dBm Input Intercept Point *1 VCC=5V, ICC=6mA, f(RF1)=450MHz, f(RF2)=451MHz, IIP3 15 f(LO)=500MHz, dBm P(RF1)=P(RF2)=--15dBm, P(LO)=--6dBm *1 : On evaluation board Ordering Information Device SMA5101-TL-H Package Shipping memo MCPH6 3,000pcs./reel Pb Free and Halogen Free Measurement Circuit VCC Balun Balun 0.1μF SMA5101 LD RF 0.1μF IF Balun 10kΩ 0.1μF 0.1μF VB LO IT15507 No. A1839-2/7 SMA5101 Evaluation Board C4 T3 T1 RF IF IC C3 R1 T2 VCC R2 C2 IC : SMA5101 T1 to T3 : Balun C1 to C4 : 0.1μF R1 : 10kΩ R2 : 0Ω (short) C1 VB LO IT15508 Circuit Example (Self Bias) Balun Balun 0.1μF SMA5101 IF LD RF 0.1μF Rbias Balun VCC 0.1μF 0.1μF LO IT15509 No. A1839-3/7 SMA5101 P1dB -- ICC 10 VCC=5V f(RF)=450MHz f(LO)=500MHz P(RF)= --15dBm 5 m = O) dB --3 P(L 0 Gc -- dB P1dB -- dBm 5 Bm d --6 P(LO)= --3dBm 0 --6dBm 0dBm Bm --5 --10 --5 0d 0 5 10 15 20 Collector Current, ICC -- mA Bm 20 )= LO --10 0 5 10 15 Collector Current, ICC -- mA 20 25 IT15977 Bm d --6 0d m dB P( 15 25 IT15976 IIP3 -- ICC 25 IIP3 -- dBm Gc -- ICC 10 VCC=5V f(RF)=450MHz f(LO)=500MHz --3 10 VCC=5V f(RF1)=450MHz f(RF2)=451MHz f(LO)=500MHz P(RF)= --15dBm 5 0 0 5 10 15 Collector Current, ICC -- mA 20 25 IT15978 No. A1839-4/7 SMA5101 Embossed Taping Specification SMA5101-TL-H No. A1839-5/7 SMA5101 Outline Drawing SMA5101-TL-H Land Pattern Example Mass (g) Unit 0.008 mm * For reference Unit: mm 2.1 0.6 0.4 0.65 0.65 No. A1839-6/7 SMA5101 Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment. The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for new introduction or other application different from current conditions on the usage of automotive device, communication device, office equipment, industrial equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. Regarding monolithic semiconductors, if you should intend to use this IC continuously under high temperature, high current, high voltage, or drastic temperature change, even if it is used within the range of absolute maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a confirmation. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of September, 2012. Specifications and information herein are subject to change without notice. PS No. A1839-7/7