WOLFSON WM8983GEFL/V

w
WM8983
Mobile Multimedia CODEC with 1W Speaker Driver
DESCRIPTION
FEATURES
The WM8983 is a low power, high quality stereo CODEC
designed for portable multimedia applications. Highly flexible
analogue mixing functions enable new application features,
combining hi-fi quality audio with voice communication.
The device integrates preamps for stereo differential mics, and
includes drivers for speaker, headphone and differential or stereo
line output. External component requirements are reduced as no
separate microphone or headphone amplifiers are required.
Stereo CODEC:
•
DAC SNR 98dB, THD -84dB (‘A’ weighted @ 48kHz)
•
ADC SNR 95dB, THD -84dB (‘A’ weighted @ 48kHz)
•
Speaker driver (1W into 8Ω BTL with 5V supply)
- SNR 90dB
- PSRR 80dB
•
Headphone driver with ‘capless’ option
- 40mW/channel output power into 16Ω / 3.3V AVDD2
•
Pop and click suppression
Advanced on-chip digital signal processing includes a 5-band
equaliser, a mixed signal Automatic Level Control for the
microphone or line input through the ADC as well as a purely
digital limiter function for record or playback. A programmable
high pass filter in the ADC path is provided for wind noise
reduction and an IIR with programmable coefficients can be used
as a notch filter to suppress fixed-frequency noise.
Mic Preamps:
•
Stereo Differential or mono microphone Interfaces
•
Programmable preamp gain
•
Pseudo differential inputs with common mode rejection
•
Programmable ALC / Noise Gate in ADC path
•
Low-noise bias supplied for electret microphones
The WM8983 digital audio interface can operate in master or
slave mode, while an integrated PLL supports flexible clocking
schemes. A-law and μ-law companding are fully supported.
The WM8983 operates at analogue supply voltages from 2.5V to
3.3V, although the digital core can operate at voltages down to
1.71V to save power. Speaker supplies can operate up to 5V for
increased speaker output power. Additional power management
control enables individual sections of the chip to be powered
down under software control.
Other Features:
•
Enhanced 3-D function for improved stereo separation
•
Highly flexible mixing functions
•
5-band equaliser (ADC or DAC path)
•
ADC Programmable high pass filter (wind noise reduction)
•
ADC Programmable IIR notch filter
•
Aux inputs for stereo analog input signals or ‘beep’
•
PLL supporting various clocks between 8MHz-50MHz
•
Sample rates supported (kHz): 8, 11.025, 16, 12, 16, 22.05,
24, 32, 44.1, 48
•
2.5V to 3.6V analogue supplies
•
1.71V to 3.6V digital supplies
•
2.5V to 5.5V speaker supplies
•
5x5mm 32-lead QFN package
APPLICATIONS
•
Multimedia mobile phones
WOLFSON MICROELECTRONICS plc
To receive regular email updates, sign up at http://www.wolfsonmicro.com/enews
Production Data, May 2010, Rev 4.3
Copyright ©2010 Wolfson Microelectronics plc
WM8983
Production Data
BLOCK DIAGRAM
w
PD, Rev 4.3, May 2010
2
WM8983
Production Data
TABLE OF CONTENTS
DESCRIPTION ....................................................................................................... 1
FEATURES ............................................................................................................ 1
APPLICATIONS ..................................................................................................... 1
BLOCK DIAGRAM ................................................................................................. 2
TABLE OF CONTENTS ......................................................................................... 3
PIN CONFIGURATION........................................................................................... 5
ORDERING INFORMATION .................................................................................. 5
PIN DESCRIPTION ................................................................................................ 6
ABSOLUTE MAXIMUM RATINGS......................................................................... 7
RECOMMENDED OPERATING CONDITIONS ..................................................... 7
ELECTRICAL CHARACTERISTICS ...................................................................... 8
TERMINOLOGY .......................................................................................................... 13
SPEAKER OUTPUT THD VERSUS POWER ...................................................... 14
POWER CONSUMPTION .................................................................................... 16
TYPICAL SCENARIOS................................................................................................ 16
AUDIO PATHS OVERVIEW ........................................................................................ 17
SIGNAL TIMING REQUIREMENTS ..................................................................... 18
SYSTEM CLOCK TIMING ........................................................................................... 18
AUDIO INTERFACE TIMING – MASTER MODE ........................................................ 18
AUDIO INTERFACE TIMING – SLAVE MODE ............................................................ 19
CONTROL INTERFACE TIMING – 3-WIRE MODE ..................................................... 20
CONTROL INTERFACE TIMING – 2-WIRE MODE ..................................................... 21
INTERNAL POWER ON RESET CIRCUIT .......................................................... 22
RECOMMENDED POWER UP/DOWN SEQUENCE................................................... 24
RECOMMENDED L/ROUT1 ENABLE SEQUENCE .................................................... 27
DEVICE DESCRIPTION ....................................................................................... 28
INTRODUCTION ......................................................................................................... 28
INPUT SIGNAL PATH ................................................................................................. 30
ANALOGUE TO DIGITAL CONVERTER (ADC) .......................................................... 39
INPUT LIMITER / AUTOMATIC LEVEL CONTROL (ALC)........................................... 44
LIMITER MODE ........................................................................................................... 47
OUTPUT SIGNAL PATH ............................................................................................. 56
3D STEREO ENHANCEMENT .................................................................................... 63
ANALOGUE OUTPUTS ............................................................................................... 63
DIGITAL AUDIO INTERFACES ................................................................................... 80
AUDIO SAMPLE RATES ............................................................................................. 86
MASTER CLOCK AND PHASE LOCKED LOOP (PLL) ............................................... 86
COMPANDING ............................................................................................................ 89
GENERAL PURPOSE INPUT/OUTPUT ...................................................................... 91
OUTPUT SWITCHING (JACK DETECT) ..................................................................... 91
CONTROL INTERFACE .............................................................................................. 93
RESETTING THE CHIP .............................................................................................. 94
POWER SUPPLIES..................................................................................................... 94
POWER MANAGEMENT............................................................................................. 94
REGISTER MAP .................................................................................................. 96
REGISTER BITS BY ADDRESS.................................................................................. 98
DIGITAL FILTER CHARACTERISTICS ............................................................. 115
TERMINOLOGY ........................................................................................................ 115
DAC FILTER RESPONSES....................................................................................... 116
ADC FILTER RESPONSES....................................................................................... 116
w
PD, Rev 4.3, May 2010
3
WM8983
Production Data
HIGHPASS FILTER ................................................................................................... 117
5-BAND EQUALISER ................................................................................................ 118
APPLICATIONS INFORMATION ....................................................................... 122
RECOMMENDED EXTERNAL COMPONENTS ........................................................ 122
IMPORTANT NOTICE ........................................................................................ 124
ADDRESS: ................................................................................................................ 124
w
PD, Rev 4.3, May 2010
4
WM8983
Production Data
PIN CONFIGURATION
ORDERING INFORMATION
ORDER CODE
TEMPERATURE
RANGE
PACKAGE
MOISTURE
SENSITIVITY LEVEL
PEAK SOLDERING
TEMPERATURE
WM8983GEFL/V
-25°C to +85°C
32-lead QFN (5 x 5 mm)
(pb-free)
MSL3
260oC
WM8983GEFL/RV
-25°C to +85°C
32-lead QFN (5 x 5 mm)
(pb-free, tape and reel)
MSL3
260oC
Note:
Reel quantity = 3,500
w
PD, Rev 4.3, May 2010
5
WM8983
Production Data
PIN DESCRIPTION
PIN
NAME
TYPE
1
LIP
Analogue input
Left MIC pre-amp positive input
DESCRIPTION
2
LIN
Analogue input
Left MIC pre-amp negative input
3
L2/GPIO2
Analogue input
Left channel line input/secondary mic pre-amp positive input/GPIO2 pin
4
RIP
Analogue input
Right MIC pre-amp positive input
5
RIN
Analogue input
Right MIC pre-amp negative input
6
R2/GPIO3
Analogue input
Right channel line input/secondary mic pre-amp positive input/GPIO3 pin
7
LRC
Digital Input / Output
DAC and ADC sample rate clock
8
BCLK
Digital Input / Output
Digital audio bit clock
9
ADCDAT
Digital Output
ADC digital audio data output
10
DACDAT
Digital Input
DAC digital audio data input
11
MCLK
Digital Input
Master clock input
12
DGND
Supply
Digital ground
13
DCVDD
Supply
Digital core logic supply
DBVDD
Supply
15
CSB/GPIO1
Digital Input / Output
16
SCLK
Digital Input
3-Wire control interface clock input / 2-wire control interface clock input
17
SDIN
Digital Input / Output
3-Wire control interface data input / 2-Wire control interface data input
18
MODE
Digital Input
19
AUXL
Analogue input
20
AUXR
Analogue input
21
OUT4
Analogue Output
right line output or mono mix output
22
OUT3
Analogue Output
mono or left line output
23
ROUT2
Analogue Output
24
AGND2
Supply
25
LOUT2
Analogue Output
26
AVDD2
Supply
27
VMID
Reference
28
AGND1
Supply
29
ROUT1
Analogue Output
30
LOUT1
Analogue Output
31
AVDD1
Supply
32
MICBIAS
Analogue Output
14
Digital buffer (I/O) supply
3-Wire control interface chip Select / GPIO1 pin
Control interface selection
Left auxillary input
Right auxillary input
Headphone or line output right 2
Analogue ground (feeds ROUT2/LOUT2 and OUT3/OUT4)
Headphone or line output left 2
Analogue supply (feeds output amplifiers ROUT2/LOUT2 and OUT3/OUT4)
Decoupling for ADC and DAC reference voltage
Analogue ground (feeds all input amplifiers, PLL, ADC and DAC, internal
bias circuits, output amplifiers LOUT1, ROUT1)
Headphone or line output right 1
Headphone or line output left 1
Analogue supply (feeds all input amplifiers, PLL, ADC and DAC, internal
bias circuits, output amplifiers LOUT1, LOUT2))
Microphone bias
Note:
It is recommended that the QFN ground paddle should be connected to analogue ground on the application PCB.
Refer to the application note WAN_0118 on “Guidelines on How to Use QFN Packages and Create Associated PCB
Footprints”
w
PD, Rev 4.3, May 2010
6
WM8983
Production Data
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously
operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given
under Electrical Characteristics at the test conditions specified.
ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible
to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage
of this device.
Wolfson tests its package types according to IPC/JEDEC J-STD-020B for Moisture Sensitivity to determine acceptable storage
conditions prior to surface mount assembly. These levels are:
MSL1 = unlimited floor life at <30°C / 85% Relative Humidity. Not normally stored in moisture barrier bag.
MSL2 = out of bag storage for 1 year at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag.
MSL3 = out of bag storage for 168 hours at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag.
The Moisture Sensitivity Level for each package type is specified in Ordering Information.
CONDITION
DBVDD, DCVDD, AVDD1 supply voltages
AVDD2 supply voltage
MIN
MAX
-0.3V
+4.5V
-0.3V
+7V
Voltage range digital inputs
DGND -0.3V
DVDD +0.3V
Voltage range analogue inputs
AGND1 -0.3V
AVDD1 +0.3V
AGND2 -0.3V
AVDD2 +0.3V
Storage temperature prior to soldering
30°C max / 85% RH max
Storage temperature after soldering
-65°C
+150°C
Notes:
1.
Analogue and digital grounds must always be within 0.3V of each other.
2.
All digital and analogue supplies are completely independent from each other.
3.
Analogue supply voltages should not be less than digital supply voltages.
4.
In non-boosted mode AVDD2 should be ≥ AVDD1. In boost mode, AVDD2 should be ≥ 1.5 x AVDD1.
5.
DBVDD must be greater than or equal to DCVDD.
RECOMMENDED OPERATING CONDITIONS
PARAMETER
SYMBOL
Digital supply range (Core)
DCVDD
TEST
CONDITIONS
MIN
TYP
1.71
2
MAX
UNIT
3.6
V
V
Digital supply range (Buffer)
DBVDD
1.71
3.6
Analogue supply range
AVDD1
2.5
3.6
V
Speaker supply range
AVDD2
2.5
5.5
V
Ground
DGND, AGND1, AGND2
0
V
Notes:
1.
Analogue supply voltages should not be less than digital supply voltages.
2.
DBVDD should be ≥ 1.9V when using the PLL.
w
PD, Rev 4.3, May 2010
7
WM8983
Production Data
ELECTRICAL CHARACTERISTICS
Test Conditions
DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Microphone Input PGA Inputs (LIP, LIN, RIP, RIN, L2, R2)
INPPGAVOLL, INPPGAVOLR, PGABOOSTL and PGABOOSTR = 0dB
Full-scale Input Signal Level –
Single-ended input via LIN/RIN 1
AVDD/3.3
Vrms
Full-scale Input Signal Level –
Pseudo-differential input 1,2
AVDD*0.7/
3.3
Vrms
150
μV
Input PGA equivalent input noise
INPPGAVOLL/R = +35.25dB
No input signal
22Hz to 20kHz
LIN, RIN input resistance
INPPGAVOLL and
INPPGAVOLR = +35.25dB
1.7
kΩ
LIN, RIN input resistance
INPPGAVOLL and
INPPGAVOLR = 0dB
47
kΩ
LIN, RIN input resistance
INPPGAVOLL and
INPPGAVOLR = -12dB
76
kΩ
LIP, RIP input resistance
All gain settings
95
kΩ
L2, R2 input resistance
L2_2INPPGA and
R2_2INPPGA = 1
L2_2BOOSTVOL and
R2_2BOOSTVOL = 000
90
kΩ
L2, R2 input resistance
L2_2INPPGA and
R2_2INPPGA = 0
L2_2BOOSTVOL and
R2_2BOOSTVOL = +6dB
11
kΩ
L2, R2 input resistance
L2_2INPPGA and
R2_2INPPGA = 0
L2_2BOOSTVOL and
R2_2BOOSTVOL = 0dB
22
kΩ
L2, R2 input resistance
L2_2INPPGA and
R2_2INPPGA = 0
L2_2BOOSTVOL and
R2_2BOOSTVOL = -12dB
60
kΩ
Input Capacitance
All analogue input pins
10
pF
Input PGA Programmable Gain
Gain adjusted by
INPPGAVOLL and
INPPGAVOLL
Programmable Gain Step Size
Guaranteed monotonic
0.75
dB
INPPGAMUTEL and
INPPGAMUTER = 1
100
dB
Input Gain Boost
PGABOOSTL and
PGABOOSTR = 0
0
dB
Input Gain Boost
PGABOOSTL and
PGABOOSTR = 1
+20
dB
Input PGA Mute Attenuation
w
-12
+35.25
dB
PD, Rev 4.3, May 2010
8
WM8983
Production Data
Test Conditions
DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Auxiliary Analogue Inputs (AUXL, AUXR)
Full-scale Input Signal Level 2
Left Input boost and mixer
enabled, at +6dB
Left Input boost and mixer
enabled, at 0dB gain
Left Input boost and mixer
enabled, at -12dB gain
Right Input boost, mixer
enabled, at +6dB gain
Right Input boost, mixer
enabled, at 0dB gain
Right Input boost, mixer
enabled, at -12dB gain
All analogue Inputs
Gain adjusted by
AUXL2BOOSTVOL and
AUXR2BOOSTVOL
Input Resistance
Input Capacitance
Gain range from AUXL and AUXR
input to left and right input PGA
mixers
AVDD/3.3
Vrms
4.3
kΩ
8.6
kΩ
39.1
kΩ
3
kΩ
6
kΩ
29
kΩ
10
AUXLBOOSTVOL and
AUXRBOOSTVOL step size
pF
+6
-12
3
dB
dB
L2, R2 Line Input Programmable Gain
Gain adjusted by
L2_2BOOSTVOL and
R2_2BOOSTVOL
Gain range from L2/R2 input to left
and right input PGA mixers
-12
L2/R2_2BOOSTVOL step size
L2/R2_2BOOSTVOL mute
attenuation
+6
dB
3
dB
100
dB
OUT4 to left or right input boost record path
Gain range into left and right input
PGA mixers
Gain adjusted by
OUT4_2ADCVOL
OUT4_2ADCVOL gain step size
OUT4_2ADCVOL mute attenuation
-6
+12
dB
3
dB
100
dB
Analogue to Digital Converter (ADC) - Input from LIN/P and RIN/P in differential configuration to input PGA
INPPGAVOLL, INPPGAVOLR, PGABOOSTL, PGABOOSTR, ADCLVOL and ADCRVOL = 0dB
Signal to Noise Ratio 3
SNR
A-weighted
93
dB
A-weighted
AVDD1=AVDD2=2.5V
91.5
dB
-12dBV Input
-78
dBFS
-12dBV Input
AVDD1=AVDD2=2.5V
-75
dBFS
-12dBV Input
-75
dBFS
-12dBV Input
AVDD1=AVDD2=2.5V
-72
dBFS
1kHz full scale input signal
100
dBFS
AVDD1=AVDD2=3.3V
Total Harmonic Distortion 4
THD
AVDD1=AVDD2=3.3V
Total Harmonic Distortion + Noise
5
THD+N
AVDD1=AVDD2=3.3V
Channel Separation
6
w
PD, Rev 4.3, May 2010
9
WM8983
Production Data
Test Conditions
DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Analogue to Digital Converter (ADC) - Input from L2, R2 into right PGA mixer. L2_2INPPGA and R2_2INPPGA = 0.
INPPGAVOLL, INPPGAVOLR, L2_2BOOSTVOL, R2_2BOOSTVOL, ADCLVOL and ADCRVOL = 0dB
Signal to Noise Ratio 3
SNR
A-weighted
95
dB
A-weighted
AVDD1=AVDD2=2.5V
93
dB
-3dBV Input
-86
dBFS
-3dBV Input
AVDD1=AVDD2=2.5V
-78
dBFS
-3dBV Input
-80
dBFS
-3dBV Input
AVDD1=AVDD2=2.5V
-76
dBFS
1kHz input signal
100
dBFS
AVDD1/3.3
Vrms
A-weighted
AVDD1=AVDD2=3.3V
100
dB
A-weighted
99
dB
0dBFS input
AVDD1=AVDD2=3.3V
-84
dBFS
0dBFS input
AVDD1=AVDD2=2.5V
-86
dBFS
0dBFS input
AVDD1=AVDD2=3.3V
-83
dBFS
0dBFS input
AVDD1=AVDD2=2.5V
-84
dBFS
1kHz signal
100
dB
AVDD1/3.3
Vrms
100
dB
A-weighted
AVDD1=AVDD2=2.5V
96
dB
0dBFS input
AVDD1=AVDD2=3.3V
-84
dBFS
0dBFS input
AVDD1=AVDD2=2.5V
-82
dBFS
0dBFS input
AVDD1=AVDD2=3.3V
-82
dBFS
0dBFS input
AVDD1=AVDD2=2.5V
-80
dBFS
1kHz input signal
100
dB
AVDD1=AVDD2=3.3V
Total Harmonic Distortion 4
THD
AVDD1=AVDD2=3.3V
Total Harmonic Distortion + Noise 5
THD+N
AVDD1=AVDD2=3.3V
Channel Separation
6
DAC to left and right mixers into 10kΩ / 50pF load on LOUT1 and ROUT1
LOUT1VOL, ROUT1VOL, DACLVOL and DACRVOL = 0dB
Full-scale output 1
LOUT1VOL and
ROUTVOL = 0dB
Signal to Noise Ratio
3
SNR
AVDD1=AVDD2=2.5V
Total Harmonic Distortion 4
Total Harmonic Distortion + Noise
Channel Separation
THD
5
THD+N
6
DAC to L/R mixer into 10kΩ / 50pF load on L/ROUT2
LOUT2VOL, ROUT2VOL, DACLVOL and DACRVOL = 0dB
Full-scale output 1
Signal to Noise Ratio 3
SNR
A-weighted
AVDD1=AVDD2=3.3V
Total Harmonic Distortion 4
Total Harmonic Distortion + Noise 5
THD
THD+N
Channel Separation 6
DAC to OUT3 and OUT4 mixers to OUT3/OUT4 outputs into 10kΩ / 50pF load. DACVOLL and DACVOLR = 0dB
Full-scale output voltage
Signal to Noise Ratio 3
SNR
A-weighted
AVDD2/3.3
Vrms
101.5
dB
AVDD1=AVDD2=3.3V
w
PD, Rev 4.3, May 2010
10
WM8983
Production Data
Test Conditions
DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated.
PARAMETER
Total Harmonic Distortion 4
SYMBOL
TEST CONDITIONS
THD
full-scale signal
MIN
TYP
MAX
UNIT
-80
dBFS
full-scale signal
AVDD1=AVDD2=2.5V
-87
dBFS
full-scale signal
-77
dBFS
full-scale signal
AVDD1=AVDD2=2.5V
-85
dBFS
1kHz signal
100
dBFS
AVDD1/3.3
Vrms
98
dB
AVDD1=AVDD2=3.3V
Total Harmonic Distortion + Noise 5
THD+N
AVDD1=AVDD2=3.3V
Channel Separation 6
DAC to left and right mixer into headphone (16Ω load) on LOUT2 and ROUT2
LOUT2VOL, ROUT2VOL, DACLVOL and DACRVOL = 0dB
Full-scale output
Signal to Noise Ratio 3
SNR
A-weighted
AVDD1=AVDD2=3.3V
Total Harmonic Distortion 4
Total Harmonic Distortion + Noise 5
THD
Po = 20mW, RL=16Ω
-76
dBFS
THD+N
Po = 20mW, RL=16Ω
-72
dBFS
1kHz signal
100
dB
Channel Separation 6
Bypass paths to left and right output mixers. BYPL2LMIX = 1 and BYPR2RMIX = 1
PGA gain range into mixer
Gain adjusted by
BYPLMIXVOL and
BYPRMIXVOL
-15
0
BYPLMIXVOL and BYPRMIXVOL
gain step into mixer
Mute attenuation
BYPL2LMIX = 0
BYPR2RMIX = 0
+6
dB
3
dB
100
dB
Analogue outputs (LOUT1, ROUT1, LOUT2, ROUT2)
Programmable Gain range
Gain adjusted by
L/ROUT1VOL and
L/ROUT2VOL
Programmable Gain step size
Mute attenuation
-57
0
+6
dB
Guaranteed
1
dB
1kHz, full scale signal
L/ROUT1MUTE = 1
L/ROUT2MUTE = 1
85
dB
AVDD2/3.3
Vrms
98
dB
A-weighted
AVDD1=AVDD2=2.5V
96
dB
22Hz to 22kHz
AVDD1=AVDD2=3.3V
95.5
dBFS
22Hz to 22kHz
AVDD1=AVDD2=2.5V
93.5
dBFS
full-scale signal
-84
dBFS
full-scale signal
AVDD1=AVDD2=2.5V
-82
dBFS
full-scale signal
-82
dBFS
-80
dBFS
LIN and RIN input PGA to input boost stage into 10kΩ / 50pF load on OUT3/OUT4 outputs
INPPGAVOLL, INPPGAVOLR, PGABOOSTL and PGABOOSTR = 0dB
Full-scale output voltage, 0dB gain
Signal to Noise Ratio 3
Total Harmonic Distortion 4
SNR
THD
A-weighted
AVDD1=AVDD2=3.3V
90
AVDD1=AVDD2=3.3V
Total Harmonic Distortion + Noise 5
THD+N
AVDD1=AVDD2=3.3V
full-scale signal
w
PD, Rev 4.3, May 2010
11
WM8983
Production Data
Test Conditions
DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
AVDD1=AVDD2=2.5V
Channel Separation 6
100
dB
AVDD1/3.3
Vrms
100
dB
A-weighted
AVDD1=AVDD2=2.5V
96
dB
22Hz to 22kHz
AVDD1=AVDD2=3.3V
95.5
dB
22Hz to 22kHz
AVDD1=AVDD2=2.5V
93.5
dB
full-scale signal
AVDD1=AVDD2=3.3V
-87
full-scale signal
-69
LIN and RIN into input PGA Bypass to LOUT1 and ROUT1 into 10kΩ / 50pF loads
BYPLMIXVOL, BYPRMIXVOL, LOUT1VOL and ROUT1VOL = 0dB
Full-scale output voltage, 0dB gain
SIGNAL TO NOISE RATIO 3
SNR
A-weighted
90
AVDD1=AVDD2=3.3V
Total Harmonic Distortion 4
THD
-75
dBFS
dBFS
AVDD1=AVDD2=2.5V
Total Harmonic Distortion + Noise 5
THD+N
full-scale signal
AVDD1=AVDD2=3.3V
-85
-73
dBFS
full-scale signal
-68
dBFS
100
dB
AVDD2/
3.3
Vrms
AVDD1=AVDD2=2.5V
Channel separation 6
1kHz full scale signal
Speaker Output (LOUT2, ROUT2 with 8Ω bridge tied load, INVROUT2=1)
7
Full scale output voltage, 0dB gain.
SPKBOOST=0
SPKBOOST=1
Output Power
Total Harmonic Distortion
Signal to Noise Ratio
Power Supply Rejection Ratio
(50Hz-22kHz)
PO
THD
SNR
PSRR
(AVDD2/
3.3)*1.5
Output power is very closely correlated with THD; see below
PO =200mW, RL = 8Ω,
AVDD2=3.3V
0.04
-68
PO =320mW, RL = 8Ω,
AVDD2=3.3V
1.0
%
-40
dB
PO =500mW, RL = 8Ω,
AVDD2=5V
0.02
-74
%
dB
PO =860mW, RL = 8Ω,
AVDD2=5V
1.0
-40
%
dB
AVDD2=3.3V,
RL = 8Ω
90
dB
AVDD2=5V,
RL = 8Ω
90
dB
%
dB
RL = 8Ω BTL
80
dB
RL = 8Ω BTL AVDD2=5V
(boost)
69
dB
Microphone Bias
Bias Voltage
MBVSEL=0
0.9*AVDD1
V
MBVSEL=1
0.65*AVDD1
V
Bias Current Source
for VMICBIAS within +/-3%
Output Noise Voltage
1kHz to 20kHz
w
3
15
mA
nV/√Hz
PD, Rev 4.3, May 2010
12
WM8983
Production Data
Test Conditions
DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Digital Input / Output
Input HIGH Level
Input LOW Level
VIL
Output HIGH Level
VOH
Output LOW Level
VOL
Input Capacitance
0.7×DBV
DD
VIH
V
0.3×DBVDD
IOL=1mA
0.9×DBV
DD
V
IOH=1mA
All digital pins
V
0.1xDBVDD
10
V
pF
TERMINOLOGY
1.
Full-scale input and output levels scale in relation to AVDD or AVDD2 depending upon the input or output used. For
example, when AVDD = 3.3V, 0dBFS = 1Vrms (0dBV). When AVDD < 3.3V the absolute level of 0dBFS will decrease
with a linear relationship to AVDD.
2.
3.
Input level to RIP and LIP in differential configurations is limited to a maximum of -3dB or performance will be reduced.
Signal-to-noise ratio (dBFS) – SNR is the difference in level between a reference full scale output signal and the
device output with no signal applied. This ratio is also called idle channel noise. (No Auto-zero or Automute function is
employed in achieving these results).
4.
Total Harmonic Distortion (dBFS) – THD is the difference in level between a reference full scale output signal and the
first seven odd harmonics of the output signal. To calculate the ratio, the fundamental frequency of the output signal is
notched out and an RMS value of the next seven harmonics is calculated.
5.
Total Harmonic Distortion plus Noise (dBFS) – THD+N is the difference in level between a reference full scale output
signal and the sum of the harmonics, wide-band noise and interference on the output signal. To calculate the ratio, the
fundamental frequency of the output signal is notched out and an RMS value of the total harmonics, wide-band noise
and interference is calculated.
Channel Separation (dB) – Also known as Cross-Talk. This is a measure of the amount one channel is isolated from
the other. Normally measured by sending a full scale signal down one channel and measuring the other.
6.
7.
The maximum output voltage can be limited by the speaker power supply. If SPKBOOST is set then AVDD2 should be
1.5xAVDD to prevent clipping taking place in the output stage (when PGA gains are set to 0dB).
w
PD, Rev 4.3, May 2010
13
WM8983
Production Data
SPEAKER OUTPUT THD VERSUS POWER
A ud io P re c is io n
W M 8 9 8 3 T H D + N vs . O utp ut P o w e r -- S P K V D D = 3 .6 V
0 8 /2 9 /0 6 1 1 :4 0 :4 4
+ 0T
-1 0
-2 0
-3 0
d
B
r
-4 0
A
-6 0
-5 0
-7 0
-8 0
-9 0
-1 0 0
0
50m
100m
150m
200m
250m
300m
350m
400m
450m
500m
550m
600m
W
Sw eep
T ra c e
C o lo r
L in e S tyle
Th ick
D a ta
1
4
7
10
1
1
1
1
C ya n
G re e n
Red
B lu e
S o li d
S o li d
S o li d
S o li d
1
1
1
1
An lr.T H D + N
An lr.T H D + N
An lr.T H D + N
An lr.T H D + N
Am
Am
Am
Am
pl
pl
pl
pl
Axi s
Com m ent
L e ft
L e ft
L e ft
L e ft
3 .6 V
3 .3 V
3V
2 .7 V
S ys te m AP 2
B o a rd R e vis io n : 2 .0
D e vic e D a te C o d e : 6 7 AAL N A
In p u t P a th : S P D IF _ IN
In p u t S i g n a l : 9 9 7 H z; S w e e p 1 0 0 % F S -> 0 % F S ; 2 4 -b i t; 2 5 6 fs (fs = 4 8 k H z)
O u tp u t P a th : R /L O U T 2 ; L O U T 2 VO L = R O U T 2 VO L = + 6 d B ; 8 o h m B T L
O u tp u t R e fe re n c e : + 4 .4 2 8 d B rA
S u p p li e s : E xte rn a l - AVD D = D B VD D = D C VD D = S e e C o m m e n t; S P K VD D = + 3 .6 V
B W fil te r : 2 2 H z - 2 2 k H z
Ad d itio n a l F i lte ri n g : N o n e
D ith e r: N o n e
R MS o r Ave ra g i n g : Ave ra g i n g
W M8 9 8 3 _ D AC _ S P K _ T H D + N _ vs _ P o w e r_ 8 o h m _ S P K VD D 3 6 V.a t2 7
Figure 1 Speaker THD+N vs Output Power (Boost Disabled: SPKVDD=3.6V; SPKBOOST=0; AVDD Range =3.6-2.7V)
Audio Precision
W M8983 THD+N vs. Output Power -- SPKVDD=4.2V
08/29/06 12:57:21
+0
T
-10
-20
-30
d
B
r
-40
A
-60
-50
-70
-80
-90
-100
0
50m
100m
150m
200m
250m
300m
350m
400m
450m
500m
550m
600m
650m
700m
750m 800m
W
Sweep
Trace
Color
Line Style
Thick
Data
1
4
7
10
1
1
1
1
Cyan
Red
Green
Blue
Solid
Solid
Solid
Solid
1
1
1
1
Anlr.THD+N
Anlr.THD+N
Anlr.THD+N
Anlr.THD+N
Am pl
Am pl
Am pl
Am pl
Axis
Com m ent
Left
Left
Left
Left
3.6V
3.3V
3V
2.7V
Sys tem AP2
Board Revis ion: 2.0
Device Date Code: 67AALNA
Input Path: SPDIF_IN
Input Signal: 997Hz; Sweep 100% FS -> 0% FS; 24-bit; 256fs (fs =48kHz)
Output Path: R/LOUT2; LOUT2VOL=ROUT2VOL=+6dB; 8ohm BTL
Output Reference: +4.428dBrA
Supplies : External - AVDD=DBVDD=DCVDD=See Com m ent; SPKVDD=+4.2V
BW filter : 22Hz - 22kHz
Additional Filtering: None
Dither: None
RMS or Averaging: Averaging
WM8983_DAC_SPK_THD+N_vs _Power_8ohm _SPKVDD=4.2V.at27
Figure 2 Speaker THD+N vs Output Power (Boost Disabled: SPKVDD=4.2V; SPKBOOST=0; AVDD Range =3.6-2.7V)
w
PD, Rev 4.3, May 2010
14
WM8983
Production Data
Audio Precision
W M8983 THD+N vs. Output Power -- Boost enabled; SPKVDD=4.2V
08/29/06 12:58:55
T
+0
-20
-30
d
B
r
-40
A
-60
-50
-70
-80
-90
-100
0
100m
200m
300m
400m
500m
600m
700m
800m
.9
W
Sweep
Trace
Color
Line Style
Thick
Data
1
4
7
10
1
1
1
1
Cyan
Red
Green
Blue
Solid
Solid
Solid
Solid
1
1
1
1
Anlr.THD+N
Anlr.THD+N
Anlr.THD+N
Anlr.THD+N
Am pl
Am pl
Am pl
Am pl
Axis
Com m ent
Left
Left
Left
Left
3.6V
3.3V
3V
2.7V
Sys tem AP2
Board Revis ion: 2.0
Device Date Code: 67AALNA
Input Path: SPDIF_IN
Input Signal: 997Hz; Sweep 100% FS -> 0% FS; 24-bit; 256fs (fs =48kHz)
Output Path: R/LOUT2; LOUT2VOL=ROUT2VOL=+6dB; 8ohm BTL
Output Reference: +4.428dBrA
Supplies : External - AVDD=DBVDD=DCVDD=See Com m ent; SPKVDD=4.2V
BW filter : 22Hz - 22kHz
Additional Filtering: None
Dither: None
RMS or Averaging: Averaging
WM8983_DAC_SPK_THD+N_vs _Power_8ohm _Boos t_SPKVDD=4.2V.at27
Figure 3 Speaker THD+N vs Output Power (Boost Mode: SPKVDD=4.2V; SPKBOOST=1; AVDD Range =3.6-2.7V)
Audio Precision
W M8983 THD+N vs. Output Power -- Boost enabled; SPKVDD=5V
08/29/06 12:48:45
+0
T
-10
-20
-30
d
B
r
-40
A
-60
-50
-70
-80
-90
-100
0
100m
200m
300m
400m
500m
600m
700m
800m
.9
1
1.1
1.2
W
Sweep
Trace
Color
Line Style
Thick
Data
1
4
7
10
1
1
1
1
Cyan
Red
Green
Blue
Solid
Solid
Solid
Solid
1
1
1
1
Anlr.THD+N
Anlr.THD+N
Anlr.THD+N
Anlr.THD+N
Am pl
Am pl
Am pl
Am pl
Axis
Com m ent
Left
Left
Left
Left
3.6V
3.3V
3V
2.7V
Sys tem AP2
Board Revis ion: 2.0
Device Date Code: 67AALNA
Input Path: SPDIF_IN
Input Signal: 997Hz; Sweep 100% FS -> 0% FS; 24-bit; 256fs (fs =48kHz)
Output Path: R/LOUT2; LOUT2VOL=ROUT2VOL=+6dB; 8ohm BTL
Output Reference: +4.428dBrA
Supplies : External - AVDD=DBVDD=DCVDD=See Com m ent; SPKVDD=5V
BW filter : 22Hz - 22kHz
Additional Filtering: None
Dither: None
RMS or Averaging: Averaging
WM8983_DAC_SPK_THD+N_vs _Power_8ohm _Boos t_SPKVDD=5V.at27
Figure 4 Speaker THD+N vs Output Power (Boost Mode: SPKVDD=5V; SPKBOOST=1; AVDD Range =3.6-2.7V)
w
PD, Rev 4.3, May 2010
15
WM8983
Production Data
POWER CONSUMPTION
TYPICAL SCENARIOS
Estimated current consumption for typical scenarios are shown below.
Power delivered to the load is not included.
MODE
IAVDD1 mA
IAVDD2 mA
IDCVDD mA
IDBVDD mA
(3.3V)
(3.3V)
(1.8V)
(1.8V)
TOTAL
mW
Off (No clocks, temperature sensor disabled)
0.010
0.010
0.001
0.002
0.071
Sleep (VREF maintained)
0.100
0.001
0.012
0.003
0.360
Mono Record from Differential MIC (8kHz, PLL enabled)
4.000
0.001
0.400
0.030
13.97
Stereo HP Playback (44.1kHz, PLL enabled)
3.700
0.950
2.100
0.100
19.31
Table 1 Power Consumption
w
PD, Rev 4.3, May 2010
16
w
R2
RIP
RIN
AUXR
AUXL
L2
LIP
LIN
OUT4_2LNR
R42[5]
L2_2INPPGA
R44[2]
LIP2INPPGA
R44[0]
VMID
VMID
INPPGAVOLR
R46[5:0]
ALCSEL[0]
R32[7]
INPPGAVOLL
R45[5:0]
ALCSEL[1]
R32[8]
AGND1
R2_2INPPGA
R44[6]
AGND1
+
AVDD1
Differential /
Single-Ended
MIC (Right)
AUXR2BOOSTVOL
R48[2:0] (Mute=000)
INPPGAMUTER
R46[6]
RIP2INPPGA
R44[4]
from
ALC
PGABOOSTR
R48[8]
R2_2BOOSTVOL
R48[6:4] (Mute=000)
L2_2BOOSTVOL
R47[6:4] (Mute=000)
from
ALC
PGABOOSTL
R47[8]
INPPGAMUTEL
R45[6]
AUXL2BOOSTVOL
R47[2:0] (Mute=000)
VMID
VMID
+
AVDD1 Differential /
Single-Ended
MIC (Lett)
OUT4_2ADCVOL
R42[8:6] (Mute=000)
AGND1
+
MODE
AVDD1
AGND1
+
AVDD1
Right
PGA
Mixer
Left
PGA
Mixer
VREF-
AGND1
VREF-
DCVDD
DGND
PLL
AGND1
DCVDD
DGND
Notch
Filter
EQ/
3D
DBVDD
VREF+
DACDAT
DGND
AVDD1
AGND1
VREF-
DGND
ADCDAT
AGND1
VREF-
R DAC
DCVDD
DGND
EQ3DMODE
R18[8]
EQ can be applied to
ADC or DAC, but not
both simultaneously
EQ/
3D
DACPOLR
R10[1]
DACPOLL
R10[0]
VREF+
AVDD1
L DAC
DCVDD
Digital Audio Interface
DGND
ADCRPOL
R14[1]
Limiter
Digital Core
ADCLPOL
R14[0]
DCVDD
ALC/
Limiter
HPF
DGND
R ADC
VREF+
AVDD1
AGND1
BYPRMIXVOL
R51[4:2]
AVDD1
DCVDD
L ADC
VREF+
AVDD1
BYPLMIXVOL
R50[4:2]
WM8983 Audio Signal Paths
AUXRMIXVOL
R51[8:6]
AUXR2RMIX
R51[5]
BYPR2RMIX
R51[1]
DACR2RMIX
R51[0]
DACL2RMIX
R49[6]
DACR2LMIX
R49[5]
DACL2LMIX
R50[0]
BYPL2LMIX
R50[1]
AUXLMIXVOL
R50[8:6]
AUXL2LMIX
R50[5]
Right
Mixer
AGND1
+
AVDD1
Left
Mixer
AGND1
+
AVDD1
BYPL2RMIX
R43[8]
BYPR2LMIX
R43[7]
LMIX2OUT3
R56[1]
LDAC2OUT3
R56[0]
BYPL2OUT3
R56[2]
OUT4_2OUT3
R56[3]
BYPR2OUT4
R57[2]
RMIX2OUT4
R57[1]
LMIX2OUT4
R57[4]
LDAC2OUT4
R57[3]
RDAC2OUT4
R57[0]
OUT3_2OUT4
R57[7]
VMID
OUT4MUTE
R57[6]
VMID
ROUT2MUTE
R55[6]
VMID
AVDD1
AGND1
AVDD1
AGND1
AVDD1
ROUT1
LOUT1
OUT3
OUT4
LOUT2
AGND2
ROUT2
AVDD2 ROUT2VOL
R55[5:0]
AGND2
AVDD2 LOUT2VOL
R54[5:0]
ROUT1VOL AGND1
R53[5:0]
AVDD1
LOUT1VOL AGND1
R52[5:0]
LOUT2MUTE
R54[6]
VMID
ROUT1MUTE
R53[6]
VMID
LOUT1MUTE
R52[6]
VMID
OUT3MUTE
R56[6]
OUT3
Mixer
AGND1
+
AVDD1
AGND1
+
AVDD1
OUT4
Mixer
Production Data
WM8983
AUDIO PATHS OVERVIEW
PD, Rev 4.3, May 2010
17
WM8983
Production Data
SIGNAL TIMING REQUIREMENTS
SYSTEM CLOCK TIMING
tMCLKL
MCLK
tMCLKH
tMCLKY
Figure 5 System Clock Timing Requirements
Test Conditions
o
DCVDD=1.8V, DBVDD=AVDD1=AVDD2=3.3V, DGND=AGND1=AGND2=0V, TA = +25 C, Slave Mode
PARAMETER
SYMBOL
CONDITIONS
MIN
TMCLKY
MCLK=SYSCLK (=256fs)
81.38
MCLK input to PLL Note 1
20
TYP
MAX
UNIT
System Clock Timing Information
MCLK cycle time
MCLK duty cycle
TMCLKDS
60:40
ns
ns
40:60
Note:
1. PLL pre-scaling and PLL N and K values should be set appropriately so that SYSCLK is no greater than 12.288MHz.
AUDIO INTERFACE TIMING – MASTER MODE
Figure 6 Digital Audio Data Timing – Master Mode (see Control Interface)
w
PD, Rev 4.3, May 2010
18
WM8983
Production Data
Test Conditions
DCVDD=1.8V, DBVDD=AVDD1=AVDD2=3.3V, DGND=AGND1=AGND2=0V, TA=+25oC, Master Mode, fs=48kHz, MCLK=256fs,
24-bit data, unless otherwise stated.
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
Audio Data Input Timing Information
LRC propagation delay from BCLK falling edge
tDL
10
ns
ADCDAT propagation delay from BCLK falling edge
tDDA
25
ns
DACDAT setup time to BCLK rising edge
tDST
10
ns
DACDAT hold time from BCLK rising edge
tDHT
10
ns
AUDIO INTERFACE TIMING – SLAVE MODE
Figure 7 Digital Audio Data Timing – Slave Mode
Test Conditions
DCVDD=1.8V, DBVDD=AVDD1=AVDD2=3.3V, DGND=AGND1=AGND2=0V, TA=+25oC, Slave Mode, fs=48kHz,
MCLK= 256fs, 24-bit data, unless otherwise stated.
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
BCLK cycle time
tBCY
50
BCLK pulse width high
tBCH
20
ns
BCLK pulse width low
tBCL
20
ns
LRC set-up time to BCLK rising edge
tLRSU
10
ns
LRC hold time from BCLK rising edge
tLRH
10
ns
DACDAT hold time from BCLK rising edge
tDH
10
ns
DACDAT set-up time to BCLK rising edge
tDS
10
ns
ADCDAT propagation delay from BCLK falling edge
tDD
Audio Data Input Timing Information
ns
25
ns
Note:
BCLK period should always be greater than or equal to MCLK period.
w
PD, Rev 4.3, May 2010
19
WM8983
Production Data
CONTROL INTERFACE TIMING – 3-WIRE MODE
3-wire mode is selected by connecting the MODE pin high.
Figure 8 Control Interface Timing – 3-Wire Serial Control Mode
Test Conditions
DCVDD=1.8V, DBVDD=AVDD1=AVDD2=3.3V, DGND=AGND1=AGND2=0V, TA=+25oC, Slave Mode, fs=48kHz, MCLK=256fs,
24-bit data, unless otherwise stated.
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
Program Register Input Information
SCLK rising edge to CSB rising edge
tSCS
80
ns
SCLK pulse cycle time
tSCY
200
ns
SCLK pulse width low
tSCL
80
ns
SCLK pulse width high
tSCH
80
ns
SDIN to SCLK set-up time
tDSU
40
ns
SCLK to SDIN hold time
tDHO
40
ns
CSB pulse width low
tCSL
40
ns
CSB pulse width high
tCSH
40
ns
CSB rising to SCLK rising
tCSS
40
ns
Pulse width of spikes that will be suppressed
tps
0
w
5
ns
PD, Rev 4.3, May 2010
20
WM8983
Production Data
CONTROL INTERFACE TIMING – 2-WIRE MODE
2-wire mode is selected by connecting the MODE pin low.
t3
t3
t5
SDIN
t4
t6
t2
t8
SCLK
t1
t9
t7
Figure 9 Control Interface Timing – 2-Wire Serial Control Mode
Test Conditions
DCVDD=1.8V, DBVDD=AVDD1=AVDD2=3.3V,
MCLK=256fs, 24-bit data, unless otherwise stated.
PARAMETER
DGND=AGND1=AGND2=0V,
SYMBOL
TA=+25oC,
MIN
Slave
TYP
Mode,
fs=48kHz,
MAX
UNIT
526
kHz
Program Register Input Information
SCLK Frequency
0
SCLK Low Pulse-Width
t1
1.3
us
SCLK High Pulse-Width
t2
600
ns
Hold Time (Start Condition)
t3
600
ns
Setup Time (Start Condition)
t4
600
ns
Data Setup Time
t5
100
SDIN, SCLK Rise Time
t6
300
ns
SDIN, SCLK Fall Time
t7
300
ns
Setup Time (Stop Condition)
t8
Data Hold Time
t9
Pulse width of spikes that will be suppressed
tps
w
ns
600
0
ns
900
ns
5
ns
PD, Rev 4.3, May 2010
21
WM8983
Production Data
INTERNAL POWER ON RESET CIRCUIT
Figure 10 Internal Power on Reset Circuit Schematic
The WM8983 includes an internal Power-On-Reset Circuit, as shown in Figure 10, which is used
reset the digital logic into a default state after power up. The POR circuit is powered from AVDD1
and monitors DCVDD. It asserts PORB low if AVDD1 or DCVDD is below a minimum threshold.
Figure 11 Typical Power up Sequence where AVDD1 is Powered before DCVDD
Figure 11 shows a typical power-up sequence where AVDD1 comes up first. When AVDD1 goes
above the minimum threshold, Vpora, there is enough voltage for the circuit to guarantee PORB is
asserted low and the chip is held in reset. In this condition, all writes to the control interface are
ignored. Now AVDD1 is at full supply level. Next DCVDD rises to Vpord_on and PORB is released high
and all registers are in their default state and writes to the control interface may take place.
On power down, where AVDD1 falls first, PORB is asserted low whenever AVDD1 drops below the
minimum threshold Vpora_off.
w
PD, Rev 4.3, May 2010
22
WM8983
Production Data
Figure 12 Typical Power up Sequence where DCVDD is Powered before AVDD1
Figure 12 shows a typical power-up sequence where DCVDD comes up first. First it is assumed that
DCVDD is already up to specified operating voltage. When AVDD1 goes above the minimum
threshold, Vpora, there is enough voltage for the circuit to guarantee PORB is asserted low and the
chip is held in reset. In this condition, all writes to the control interface are ignored. When AVDD1
rises to Vpora_on, PORB is released high and all registers are in their default state and writes to the
control interface may take place.
On power down, where DCVDD falls first, PORB is asserted low whenever DCVDD drops below the
minimum threshold Vpord_off.
SYMBOL
MIN
TYP
MAX
UNIT
Vpora
0.4
0.6
0.8
V
Vpora_on
0.9
1.2
1.6
V
Vpora_off
0.4
0.6
0.8
V
Vpord_on
0.5
0.7
0.9
V
Vpord_off
0.4
0.6
0.8
V
Table 2 Typical POR Operation (Typical Simulated Values)
Notes:
w
1.
If AVDD1 and DCVDD suffer a brown-out (i.e. drop below the minimum recommended operating
level but do not go below Vpora_off or Vpord_off) then the chip will not reset and will resume normal
operation when the voltage is back to the recommended level again.
2.
The chip will enter reset at power down when AVDD1 or DCVDD falls below Vpora_off or Vpord_off.
This may be important if the supply is turned on and off frequently by a power management
system.
3.
The minimum tpor period is maintained even if DCVDD and AVDD1 have zero rise time. This
specification is guaranteed by design rather than test.
PD, Rev 4.3, May 2010
23
WM8983
Production Data
RECOMMENDED POWER UP/DOWN SEQUENCE
In order to minimise output pop and click noise, it is recommended that the WM8983 device is
powered up and down under control using the following sequences:
Power Up:
•
Turn on external power supplies. Wait for supply voltage to settle.
•
Set low bias mode, BIASCUT = 1.
•
Mute all Outputs and set PGAs to minimum gain, R52 to R57 = 0x140h.
•
Enable VMID independent current bias, POBCTRL = 1, DELEN = 1.
•
Enable required outputs, DACs and mixers.
•
Enable analogue bias, BIASEN, and VMID with required charge time e.g. VMIDSEL=01
= 100kΩ.
•
Setup digital interface, input amplifiers, PLL, ADCs and DACs for desired operation.
•
Unmute L/ROUT1 and set desired volume, e.g. for 0dB R52 and R53 = 0x139h.
•
Unmute L/ROUT2 and set desired volume, e.g. for 0dB R54 and R55 = 0x139h.
•
Disable VMID independent current bias, POBCTRL = 0, DELEN = 0.
Power Down:
•
Disable Thermal shutdown
•
Disable VMIDSEL=00 and BIASEN=0
•
Wait for VMID to discharge
•
Power off registers R1, R2, R3 = 0x000h
•
Remove external power supplies
Note:
Charging time constant is determined by impedance selected by VMIDSEL and the value of
decoupling capacitor connected to VMID pin.
w
PD, Rev 4.3, May 2010
24
WM8983
Production Data
Figure 13 ADC Power Up and Down Sequence (not to scale)
SYMBOL
tmidrail_on
MIN
TYPICAL
300
MAX
UNIT
ms
tmidrail_off
>6
s
tadcint
2/fs
n/fs
ADC Group Delay
29/fs
n/fs
Table 3 Typical POR Operation (typical simulated values)
w
PD, Rev 4.3, May 2010
25
WM8983
Production Data
Notes:
1.
The analogue input pin charge time, tmidrail_on, is determined by the VMID pin charge time. This
time is dependent upon the value of VMID decoupling capacitor and VMID pin input resistance
and AVDD power supply rise time.
2.
The analogue input pin discharge time, tmidrail_off, is determined by the analogue input coupling
capacitor discharge time. The time, tmidrail_off, is measured using a 1μF capacitor on the analogue
input but will vary dependent upon the value of input coupling capacitor.
3.
While the ADC is enabled there will be LSB data bit activity on the ADCDAT pin due to system
noise but no significant digital output will be present.
4.
The VMIDSEL and BIASEN bits must be set to enable analogue input midrail voltage and for
normal ADC operation.
5.
ADCDAT data output delay from power up – with power supplies starting from 0V – is
determined primarily by the VMID charge time. ADC initialisation and power management bits
may be set immediately after POR is released; VMID charge time will be significantly longer and
will dictate when the device is stabilised for analogue input.
6.
ADCDAT data output delay at power up from device standby (power supplies already applied) is
determined by ADC initialisation time, 2/fs.
Figure 14 DAC Power Up and Down Sequence (not to scale)
SYMBOL
MIN
TYPICAL
MAX
UNIT
tline_midrail_on
300
tline_midrail_off
>6
ms
s
thp_midrail_on
300
ms
thp__midrail_off
>6
s
tdacint
2/fs
n/fs
DAC Group Delay
29/fs
n/fs
Table 4 Typical POR Operation (typical simulated values)
w
PD, Rev 4.3, May 2010
26
WM8983
Production Data
Notes:
1.
The lineout charge time, tline_midrail_on, is determined by the VMID pin charge time. This time is
dependent upon the value of VMID decoupling capacitor and VMID pin input resistance and
AVDD power supply rise time. The values above were measured using a 4.7μF capacitor.
2.
It is not advisable to allow DACDAT data input during initialisation of the DAC. If the DAC data
value is not zero at point of initialisation, then this is likely to cause a pop noise on the analogue
outputs. The same is also true if the DACDAT is removed at a non-zero value, and no mute
function has been applied to the signal beforehand.
3.
The lineout discharge time, tline_midrail_off, is determined by the VMID pin discharge time. This time
is dependent upon the value of VMID decoupling capacitor and VMID pin input resistance. The
values above were measured using a 4.7μF capacitor.
4.
The headphone charge time, thp_midrail_on, is dependent upon the value of VMID decoupling
capacitor and VMID pin input resistance and AVDD power supply rise time. The values above
were measured using a 4.7μF VMID decoupling capacitor.
5.
The headphone discharge time, thp_midrail_off, is dependent upon the value of VMID decoupling
capacitor and VMID pin input resistance. The values above were measured using a 4.7μF VMID
decoupling capacitor.
6.
The VMIDSEL and BIASEN bits must be set to enable analogue output midrail voltage and for
normal DAC operation.
RECOMMENDED L/ROUT1 ENABLE SEQUENCE
In order to minimise click noise, it is recommended that the WM8983 headphone outputs are enabled
using the following sequence:
•
Activate dual enable function DELEN = 1 (R42).
•
Enable L/ROUT1 amplifier core, LOUT1EN = 1, ROUT1EN = 1 (R2).
•
Enable output FETs, OUT1DEL = 1 (R42).
•
Disable DELEN = 0.
•
Reset OUT1DEL = 0.
Notes:
All outputs on WM8983 can also be enabled with a single write to enable bits in registers 2 and 3
without click minimisation. Disabling outputs does not require click minimisation.
w
PD, Rev 4.3, May 2010
27
WM8983
Production Data
DEVICE DESCRIPTION
INTRODUCTION
The WM8983 is a low power audio CODEC combining a high quality stereo audio DAC and ADC,
with flexible line and microphone input and output processing.
FEATURES
The chip offers great flexibility in use, and so can support many different modes of operation as
follows:
MICROPHONE INPUTS
Two pairs of stereo microphone inputs are provided, allowing a pair of stereo microphones to be
pseudo-differentially connected, with user defined gain. The provision of the common mode input pin
for each stereo input allows for rejection of common mode noise on the microphone inputs (level
depends on gain setting chosen). A microphone bias is output from the chip which can be used to
bias both microphones. The signal routing can be configured to allow manual adjustment of mic
levels, or to allow the ALC loop to control the level of mic signal that is transmitted.
Total gain through the microphone paths of up to +55.25dB can be selected.
PGA AND ALC OPERATION
A programmable gain amplifier is provided in the input path to the ADC. This may be used manually
or in conjunction with a mixed analogue/digital automatic level control (ALC) which keeps the
recording volume constant.
LINE INPUTS (AUXL, AUXR)
AUXL and AUXR, can be used as a stereo line input or as an input for warning tones (or ‘beeps’) etc.
These inputs can be summed into the record paths, along with the microphone preamp outputs, so
allowing for mixing of audio with ‘backing music’ etc as required.
ADC
The stereo ADC uses a 24-bit high-order oversampling architecture to deliver optimum performance
with low power consumption.
HI-FI DAC
The hi-fi DAC provides high quality audio playback suitable for all portable audio hi-fi type
applications, including MP3 players, portable multimedia devices and portable disc players of all
types.
OUTPUT MIXERS
Flexible mixing is provided on the outputs of the device. A stereo mixer is provided for the stereo
headphone or line outputs, LOUT1/ROUT1, and additional summers on the OUT3/OUT4 outputs
allow for an optional differential or stereo line output on these pins. Gain adjustment PGAs are
provided for the LOUT1/ROUT1 and LOUT2/ROUT2 outputs, and signal switching is provided to
allow for all possible signal combinations.
w
PD, Rev 4.3, May 2010
28
WM8983
Production Data
OUT3 and OUT4 can be configured to provide an additional stereo or mono differential lineout from
the output of the DACs, the mixers or the input microphone boost stages. They can also provide a
midrail reference for pseudo differential inputs to external amplifiers.
AUDIO INTERFACES
The WM8983 has a standard audio interface, to support the transmission of stereo data to and from
the chip. This interface is a 3 wire standard audio interface which supports a number of audio data
formats including:
2
•
IS
•
DSP/PCM Mode (a burst mode in which LRC sync plus 2 data packed words are
transmitted)
•
MSB-First, left justified
•
MSB-First, right justified
The interface can operate in master or slave modes.
CONTROL INTERFACES
To allow full software control over all features, the WM8983 offers a choice of 2 or 3 wire control
interface. It is fully compatible and an ideal partner for a wide range of industry standard
microprocessors, controllers and DSPs.
Selection of the mode is via the MODE pin. In 2 wire mode, the address of the device is fixed as
0011010.
CLOCKING SCHEMES
WM8983 offers the normal audio DAC clocking scheme operation, where 256fs MCLK is provided to
the DAC and ADC.
A PLL is included which may be used to generate these clocks in the event that they are not available
from the system controller. This PLL can accept a range of common input clock frequencies between
8MHz and 50MHz to generate high quality audio clocks. If this PLL is not required for generation of
these clocks, it can be reconfigured to generate alternative clocks which may then be output on the
GPIO pins and used elsewhere in the system.
POWER CONTROL
The design of the WM8983 has given much attention to power consumption without compromising
performance. It operates at very low voltages, includes the ability to power off any unused parts of the
circuitry under software control, and includes standby and power off modes.
AUXILIARY ANALOG INPUT SUPPORT
Additional stereo analog signals might be connected to the Line inputs of WM8983 (e.g. melody chip
or FM radio), and the stereo signal listened to via headphones, or recorded, simultaneously if
required.
w
PD, Rev 4.3, May 2010
29
WM8983
Production Data
INPUT SIGNAL PATH
The WM8983 has a number of flexible analogue inputs. There are two input channels, Left and
Right, each of which consists of an input PGA stage followed by a boost/mix stage which drives into
the hi-fi ADC. Each input path has three input pins which can be configured in a variety of ways to
accommodate single-ended, differential or dual differential microphones. There are two auxiliary
input pins which can be fed into to the input boost/mix stage as well as driving into the output path. A
bypass path exists from the output of the boost/mix stage into the output left/right mixers.
MICROPHONE INPUTS
The WM8983 can accommodate a variety of microphone configurations including single ended and
pseudo differential inputs. The inputs to the left pseudo differential input PGA are LIP and L2. The
inputs to the right pseudo differential input PGA are RIP and R2. LIN and RIN are used for a.c.
coupled ground inputs.
In single-ended microphone input configuration the microphone signal should be input to LIN or RIN
and the non-inverting input of the input PGA clamped to VMID.
Figure 15 Microphone Input PGA Circuit
w
PD, Rev 4.3, May 2010
30
WM8983
Production Data
The input PGAs are enabled by the INPPGAENL and INPPGAENR register bits.
REGISTER
ADDRESS
BIT
R2
Power
Management
2
LABEL
DEFAULT
DESCRIPTION
2
INPPGAENL
0
Left channel input PGA enable
0 = disabled
1 = enabled
3
INPPGAENR
0
Right channel input PGA enable
0 = disabled
1 = enabled
Table 5 Input PGA Enable Register Settings
REGISTER
ADDRESS
BIT
R44
Input
Control
0
LABEL
LIP2INPPGA
DEFAULT
1
DESCRIPTION
Connect LIP pin to left channel input PGA
amplifier positive terminal.
0 = LIP not connected to input PGA
1 = input PGA amplifier positive terminal
connected to LIP (constant input
impedance)
1
LIN2INPPGA
1
Connect LIN pin to left channel input PGA
negative terminal.
0 = LIN not connected to input PGA
1 = LIN connected to input PGA amplifier
negative terminal.
2
L2_2INPPGA
0
Connect L2 pin to left channel input PGA
positive terminal.
0 = L2 not connected to input PGA
1 = L2 connected to input PGA amplifier
positive terminal (constant input
impedance).
4
RIP2INPPGA
1
Connect RIP pin to right channel input
PGA amplifier positive terminal.
0 = RIP not connected to input PGA
1 = right channel input PGA amplifier
positive terminal connected to RIP
(constant input impedance)
5
RIN2INPPGA
1
Connect RIN pin to right channel input
PGA negative terminal.
0 = RIN not connected to input PGA
1 = RIN connected to right channel input
PGA amplifier negative terminal.
6
R2_2INPPGA
0
Connect R2 pin to right channel input PGA
positive terminal.
0 = R2 not connected to input PGA
1 = R2 connected to input PGA amplifier
positive terminal (constant input
impedance).
Table 6 Input PGA Control
INPUT PGA VOLUME CONTROLS
The input microphone PGAs have a gain range from -12dB to +35.25dB in 0.75dB steps. The gain
from the LIN/RIN input to the PGA output and from the L2/R2 amplifier to the PGA output are always
common and controlled by the register bits INPPGAVOLL/R[5:0]. These register bits also affect the
LIP pin when LIP2INPPGA=1, the L2 pin when L2_2INPPGA=1, the RIP pin when RIP2INPPGA=1
and the L2 pin when L2_2INPPGA=1.
When the Automatic Level Control (ALC) is enabled the input PGA gains are controlled automatically
and the INPPGAVOLL/R bits should not be used.
w
PD, Rev 4.3, May 2010
31
WM8983
Production Data
REGISTER
ADDRESS
BIT
R45
Left channel
input PGA
volume
control
5:0
R46
Right
channel
input PGA
volume
control
R32
ALC control
1
LABEL
INPPGAVOLL
DEFAULT
010000
DESCRIPTION
Left channel input PGA volume
000000 = -12dB
000001 = -11.25db
.
010000 = 0dB
.
111111 = +35.25dB
6
INPPGAMUTEL
0
Mute control for left channel input PGA:
0 = Input PGA not muted, normal
operation
1 = Input PGA muted (and disconnected
from the following input BOOST stage).
7
INPPGAZCL
0
Left channel input PGA zero cross
enable:
0 = Update gain when gain register
changes
1 = Update gain on 1st zero cross after
gain register write.
8
INPPGAVU
Not
latched
INPPGA left and INPPGA right volume
do not update until a 1 is written to
INPPGAVU (in reg 45 or 46)
(See “Volume Updates” below)
5:0
INPPGAVOLR
010000
Right channel input PGA volume
000000 = -12dB
000001 = -11.25db
.
010000 = 0dB
.
111111 = +35.25dB
6
INPPGAMUTER
0
Mute control for right channel input PGA:
0 = Input PGA not muted, normal
operation
1 = Input PGA muted (and disconnected
from the following input BOOST stage).
7
INPPGAZCR
0
Right channel input PGA zero cross
enable:
0 = Update gain when gain register
changes
1 = Update gain on 1st zero cross after
gain register write.
8
INPPGAVU
Not
latched
INPPGA left and INPPGA right volume
do not update until a 1 is written to
INPPGAVU (in reg 45 or 46)
(See “Volume Updates” below)
8:7
ALCSEL
00
ALC function select:
00 = ALC off
01 = ALC right only
10 = ALC left only
11 = ALC both on
Table 7 Input PGA Volume Control
w
PD, Rev 4.3, May 2010
32
WM8983
Production Data
VOLUME UPDATES
Volume settings will not be applied to the PGAs until a ‘1’ is written to one of the INPPGAVU bits.
This is to allow left and right channels to be updated at the same time, as shown in Figure 16.
Figure 16 Simultaneous Left and Right Volume Updates
If the volume is adjusted while the signal is a non-zero value, an audible click can occur as shown in
Figure 17.
Figure 17 Click Noise during Volume Update
In order to prevent this click noise, a zero cross function is provided. When enabled, this will cause
the PGA volume to update only when a zero crossing occurs, minimising click noise as shown in
Figure 18.
w
PD, Rev 4.3, May 2010
33
WM8983
Production Data
Figure 18 Volume Update Using Zero Cross Detection
If there is a long period where no zero-crossing occurs, a timeout circuit in the WM8983 will
automatically update the volume. The volume updates will occur between one and two timeout
periods, depending on when the INPPGAVU bit is set as shown in Figure 19.
Figure 19 Volume Update after Timeout
w
PD, Rev 4.3, May 2010
34
WM8983
Production Data
AUXILLIARY INPUTS
There are two auxiliary inputs, AUXL and AUXR which can be used for a variety of purposes such as
stereo line inputs or as a ‘beep’ input signal to be mixed with the outputs.
As signal inputs, AUXL/R inputs can be used as a line input to the input BOOST stage which has
adjustable gain of -12dB to +6dB in 3dB steps, with an additional “off” state (i.e. not connected to
ADC input). See the INPUT BOOST section for further details.
The AUXL/R inputs can also be mixed into the output channel mixers, with a gain of -15dB to +6dB
plus off.
INPUT BOOST
Each of the stereo input PGA stages is followed by an input BOOST circuit. The input BOOST circuit
has 3 selectable inputs: the input microphone PGA output, the AUX amplifier output and the L2/R2
input pin (can be used as a line input, bypassing the input PGA). These three inputs can be mixed
together and have individual gain boost/adjust as shown in Figure 20.
Figure 20 Input Boost Stage
w
PD, Rev 4.3, May 2010
35
WM8983
Production Data
The input PGA paths can have a +20dB boost (PGABOOSTL/R=1) , a 0dB pass through
(PGABOOSTL/R=0) or be completely isolated from the input boost circuit (INPPGAMUTEL/R=1).
REGISTER
ADDRESS
BIT
LABEL
DEFAULT
DESCRIPTION
R47
Left Input
BOOST
control
8
PGABOOSTL
1
Boost enable for left channel input
PGA:
0 = PGA output has +0dB gain through
input BOOST stage.
1 = PGA output has +20dB gain
through input BOOST stage.
R48
Right Input
BOOST
control
8
PGABOOSTR
1
Boost enable for right channel input
PGA:
0 = PGA output has +0dB gain through
input BOOST stage.
1 = PGA output has +20dB gain
through input BOOST stage.
Table 8 Input BOOST Stage Control
The Auxilliary amplifier path to the BOOST stages is controlled by the AUXL2BOOSTVOL[2:0] and
AUXR2BOOSTVOL[2:0] register bits. When AUXL2BOOSTVOL/AUXR2BOOSTVOL=000 this path
is completely disconnected from the BOOST stage. Settings 001 through to 111 control the gain in
3dB steps from -12dB to +6dB.
The L2/R2 path to the BOOST stage is controlled by the LIP2BOOSTVOL[2:0] and the
RIP2BOOSTVOL[2:0] register bits. When L2_2BOOSTVOL/R2_2BOOSTVOL=000 the L2/R2 input
pin is completely disconnected from the BOOST stage. Settings 001 through to 111 control the gain
in 3dB steps from -12dB to +6dB.
w
PD, Rev 4.3, May 2010
36
WM8983
Production Data
REGISTER
ADDRESS
R42
BIT
8:6
LABEL
OUT4_2ADCVOL
DEFAULT
000
OUT4 to ADC
DESCRIPTION
Controls the OUT4 to ADC input
boost stage:
000 = Path disabled
(disconnected)
001 = -12dB gain
010 = -9dB gain
011 = -6dB gain
100 = -3dB gain
101 = +0dB gain
110 = +3dB gain
111 = +6dB gain
R47
Left channel
Input BOOST
control
5
OUT4_2LNR
0
OUT4 to L or R ADC input
0 = Right ADC input
1 = Left ADC input
2:0
AUXL2BOOSTVOL
000
Controls the auxiliary amplifier to
the left channel input boost stage:
000 = Path disabled
(disconnected)
001 = -12dB gain
010 = -9dB gain
011 = -6dB gain
100 = -3dB gain
101 = +0dB gain
110 = +3dB gain
111 = +6dB gain
6:4
L2_2BOOSTVOL
000
Controls the L2 pin to the left
channel input boost stage:
000 = Path disabled
(disconnected)
001 = -12dB gain
010 = -9dB gain
011 = -6dB gain
100 = -3dB gain
101 = +0dB gain
110 = +3dB gain
111 = +6dB gain
R48
Right channel
Input BOOST
control
2:0
AUXR2BOOSTVOL
000
Controls the auxiliary amplifier to
the right channel input boost
stage:
000 = Path disabled
(disconnected)
001 = -12dB gain
010 = -9dB gain
011 = -6dB gain
100 = -3dB gain
101 = +0dB gain
110 = +3dB gain
111 = +6dB gain
w
PD, Rev 4.3, May 2010
37
WM8983
Production Data
REGISTER
ADDRESS
BIT
LABEL
6:4
DEFAULT
R2_2BOOSTVOL
DESCRIPTION
Controls the R2 pin to the right
channel input boost stage:
000 = Path disabled
(disconnected)
000
001 = -12dB
010 = -9dB gain
011 = -6dB gain
100 = -3dB gain
101 = +0dB gain
110 = +3dB gain
111 = +6dB gain
Table 9 Input BOOST Stage Control
The BOOST stage is enabled under control of the BOOSTEN register bit.
REGISTER
ADDRESS
R2
Power
management
2
BIT
LABEL
DEFAULT
DESCRIPTION
4
BOOSTENL
0
Left channel Input BOOST enable
0 = Boost stage OFF
1 = Boost stage ON
5
BOOSTENR
0
Right channel Input BOOST enable
0 = Boost stage OFF
1 = Boost stage ON
Table 10 Input BOOST Enable Control
MICROPHONE BIASING CIRCUIT
The MICBIAS output provides a low noise reference voltage suitable for biasing electret type
microphones and the associated external resistor biasing network. Refer to the Applications
Information section for recommended external components. The MICBIAS voltage can be altered via
the MBVSEL register bit. When MBVSEL=0, MICBIAS=0.9*AVDD1 and when MBVSEL=1,
MICBIAS=0.65*AVDD1. The output can be enabled or disabled using the MICBEN control bit.
REGISTER
ADDRESS
BIT
4
R1
Power
management 1
LABEL
DEFAULT
MICBEN
0
DESCRIPTION
Microphone Bias Enable
0 = OFF (high impedance output)
1 = ON
Table 11 Microphone Bias Enable Control
REGISTER
ADDRESS
R44
Input control
BIT
8
LABEL
MBVSEL
DEFAULT
0
DESCRIPTION
Microphone Bias Voltage Control
0 = 0.9 * AVDD1
1 = 0.65 * AVDD1
Table 12 Microphone Bias Voltage Control
The internal MICBIAS circuitry is shown in Figure 21. Note that the maximum source current
capability for MICBIAS is 3mA. The external biasing resistors therefore must be large enough to limit
the MICBIAS current to 3mA.
w
PD, Rev 4.3, May 2010
38
WM8983
Production Data
VMI
MICBE
MICBIAS
internal
resistor
internal
resistor
MBVSEL=0
MICBIA
= 1.8 x VMID
= 0.9 X AVDD1
MBVSEL=1
MICBIA
= 1.3 x VMID
= 0.65 X AVDD1
AGND1
Figure 21 Microphone Bias Schematic
ANALOGUE TO DIGITAL CONVERTER (ADC)
The WM8983 uses stereo multi-bit, oversampled sigma-delta ADCs. The use of multi-bit feedback
and high oversampling rates reduces the effects of jitter and high frequency noise. The ADC Full
Scale input level is proportional to AVDD1. With a 3.3V supply voltage, the full scale level is 1.0Vrms.
Any voltage greater than full scale may overload the ADC and cause distortion.
ADC DIGITAL FILTERS
The ADC filters perform true 24 bit signal processing to convert the raw multi-bit oversampled data
from the ADC to the correct sampling frequency to be output on the digital audio interface. The digital
filter path for each ADC channel is illustrated in Figure 22.
Figure 22 ADC Digital Filter Path
The ADCs are enabled by the ADCENL/R register bit.
REGISTER
ADDRESS
R2
Power
management 2
BIT
LABEL
DEFAULT
DESCRIPTION
0
ADCENL
0
Enable ADC left channel:
0 = ADC disabled
1 = ADC enabled
1
ADCENR
0
Enable ADC right channel:
0 = ADC disabled
1 = ADC enabled
Table 13 ADC Enable Control
w
PD, Rev 4.3, May 2010
39
WM8983
Production Data
The polarity of the output signal can also be changed under software control using the
ADCLPOL/ADCRPOL register bit. The oversampling rate of the ADC can be adjusted using the
ADCOSR register bit. With ADCOSR=0 the oversample rate is 64x which gives lowest power
operation and when ADCOSR=1 the oversample rate is 128x which gives best performance.
REGISTER
ADDRESS
BIT
R14
ADC Control
LABEL
DEFAULT
0
ADCLPOL
0
1
ADCRPOL
0
DESCRIPTION
ADC left channel polarity adjust:
0 = normal
1 = inverted
ADC right channel polarity adjust:
0 = normal
1 = inverted
3
ADCOSR
0
ADC oversample rate select:
0 = 64x (lower power)
1 = 128x (best performance)
Table 14 ADC Control
SELECTABLE HIGH PASS FILTER
A selectable high pass filter is provided. To disable this filter set HPFEN=0. The filter has two
modes controlled by HPFAPP. In Audio Mode (HPFAPP=0) the filter is first order, with a cut-off
frequency of 3.7Hz. In Application Mode (HPFAPP=1) the filter is second order, with a cut-off
frequency selectable via the HPFCUT register. The cut-off frequencies when HPFAPP=1 are shown
in Table 15.
REGISTER
ADDRESS
BIT
R14
ADC Control
LABEL
DEFAULT
8
HPFEN
1
7
HPFAPP
0
DESCRIPTION
High Pass Filter Enable
0 = disabled
1 = enabled
Select audio mode or application mode
0 = Audio mode (1st order, fc = ~3.7Hz)
1 = Application mode (2nd order, fc =
HPFCUT)
6:4
HPFCUT
000
Application mode cut-off frequency
See Table 16 for details.
Table 15 ADC Enable Control
HPFCUT
SR=101/100
SR=011/010
[2:0]
SR=001/000
fs (kHz)
•
•
1.025
•
2
•
6
•
2.05
•
4
•
2
•
4.1
•
8
000
82
113
122
82
113
122
82
113
122
001
102
141
153
102
141
153
102
141
153
010
131
180
156
131
180
156
131
180
196
011
163
225
245
163
225
245
163
225
245
100
204
281
306
204
281
306
204
281
306
101
261
360
392
261
360
392
261
360
392
110
327
450
490
327
450
490
327
450
490
111
408
563
612
408
563
612
408
563
612
Table 16 High Pass Filter Cut-off Frequencies (HPFAPP=1)
Note that the High Pass filter values (when HPFAPP=1) are calculated on the assumption that the
SR register bits are set correctly for the actual sample rate as shown in Table 16. Sampling rate
(SR) is enabled by register bits R7[1:3].
w
PD, Rev 4.3, May 2010
40
WM8983
Production Data
PROGRAMMABLE IIR NOTCH FILTER
A programmable notch filter is provided. This filter has a variable centre frequency and bandwidth,
programmable via two coefficients, a0 and a1. a0 and a1 are represented by the register bits
NFA0[13:0] and NFA1[13:0]. Because these coefficient values require four register writes to setup
there is an NFU (Notch Filter Update) flag which should be set only when all four registers are setup.
REGISTER
ADDRESS
BIT
R27
Notch Filter 1
LABEL
DEFAULT
DESCRIPTION
6:0
NFA0[13:7]
0
Notch Filter a0 coefficient, bits [13:7]
7
NFEN
0
8
NFU
0
Notch filter enable:
0 = Disabled
1 = Enabled
Notch filter update. The notch filter
values used internally only update
when one of the NFU bits is set high.
Notch Filter a0 coefficient, bits [6:0]
R28
Notch Filter 2
6:0
NFA0[6:0]
0
8
NFU
0
R29
Notch Filter 3
6:0
NFA1[13:7]
0
8
NFU
0
R30
Notch Filter 4
0-6
NFA1[6:0]
0
8
NFU
0
Notch filter update. The notch filter
values used internally only update
when one of the NFU bits is set high.
Notch Filter a1 coefficient, bits [13:7]
Notch filter update. The notch filter
values used internally only update
when one of the NFU bits is set high.
Notch Filter a1 coefficient, bits [6:0]
Notch filter update. The notch filter
values used internally only update
when one of the NFU bits is set high.
Table 17 Notch Filter Function
The coefficients are calculated as follows:
a0 =
1 − tan( wb / 2)
1 + tan( wb / 2)
a1 = −(1 + a0 ) cos(w0 )
Where:
w0 = 2πf c / f s
wb = 2πf b / f s
fc = centre frequency in Hz, fb = -3dB bandwidth in Hz, fs = sample frequency in Hz
The actual register values can be determined from the coefficients as follows:
13
NFA0 = -a0 x 2
12
NFA1 = -a1 x 2
w
PD, Rev 4.3, May 2010
41
WM8983
Production Data
NOTCH FILTER WORKED EXAMPLE
The following example illustrates how to calculate the a0 and a1 coefficients for a desired centre
frequency and -3dB bandwidth.
Fc = 1000 Hz
fb = 100 Hz
fs = 48000 Hz
w0 =
wb =
a0 =
2πf c
fs
2πf b
fs
 1000  = 0.1308996939
rads

 48000 
= 2π 
 100  =
 0.01308996939 rads
 48000 
= 2π 
1 − tan (wb / 2 )
1 + tan (wb / 2 )
=
1 − tan ( 0 .01308996939 / 2 )
1 + tan ( 0 .01308996939 / 2 )
= 0 .9869949627
a1 = − (1 + a 0 ) cos( w0 ) = − (1 + 0.9869949627 ) cos( 0.1308996939 ) = −1.969995945
NFA0 = -a0 x 213 = -8085 (rounded to nearest whole number)
NFA1 = -a1 x 212 = 8069 (rounded to nearest whole number)
These values are then converted to a 2’s complement notation:
NFA0[13:0] = 14’h1F95; Converting to 2’s complement NFA0 = 14’h4000 – 14’h1F95 = 14’h206B
NFA1[13:0] = 14’h1F85; Converting to 2’s complement NFA0 = 14’h1F85
w
PD, Rev 4.3, May 2010
42
WM8983
Production Data
DIGITAL ADC VOLUME CONTROL
The output of the ADCs can be digitally attenuated over a range from –127dB to 0dB in 0.5dB steps.
The gain for a given eight-bit code X is given by:
0.5 × (G-255) dB for 1 ≤ G ≤ 255;
REGISTER
ADDRESS
R15
Left channel
ADC Digital
Volume
BIT
7:0
LABEL
MUTE for G = 0
DEFAULT
DESCRIPTION
ADCLVOL
11111111
Left ADC Digital Volume Control
[7:0]
( 0dB )
0000 0000 = Digital Mute
0000 0001 = -127dB
0000 0010 = -126.5dB
… 0.5dB steps up to
1111 1111 = 0dB
R16
Right channel
ADC Digital
Volume
8
ADCVU
Not
latched
ADC left and ADC right volume do not
update until a 1 is written to ADCVU (in
reg 15 or 16)
7:0
ADCRVOL
[7:0]
11111111
( 0dB )
Right ADC Digital Volume Control
0000 0000 = Digital Mute
0000 0001 = -127dB
0000 0010 = -126.5dB
... 0.5dB steps up to
1111 1111 = 0dB
8
ADCVU
Not
latched
ADC left and ADC right volume do not
update until a 1 is written to ADCVU (in
reg 15 or 16)
Table 18 ADC Digital Volume Control
w
PD, Rev 4.3, May 2010
43
WM8983
Production Data
INPUT LIMITER / AUTOMATIC LEVEL CONTROL (ALC)
The WM8983 has an automatic PGA gain control circuit, which can function as an input peak limiter
or as an automatic level control (ALC).
The Automatic Level Control (ALC) provides continuous adjustment of the input PGA in response to
the amplitude of the input signal. A digital peak detector monitors the input signal amplitude and
compares it to a register defined threshold level (ALCLVL).
If the signal is below the threshold, the ALC will increase the gain of the PGA at a rate set by
ALCDCY. If the signal is above the threshold, the ALC will reduce the gain of the PGA at a rate set
by ALCATK.
The ALC has two modes selected by the ALCMODE register: normal mode and peak limiter mode.
The ALC/limiter function is enabled by settings the register bits R32[8:7] ALCSEL.
REGISTER
ADDRESS
R32 (20h)
ALC Control
1
BIT
2:0
LABEL
ALCMIN
DEFAULT
000 (-12dB)
[2:0]
DESCRIPTION
Set minimum gain of PGA
000 = -12dB
001 = -6dB
010 = 0dB
011 = +6dB
100 = +12dB
101 = +18dB
110 = +24dB
111 = +30dB
5:3
ALCMAX
[2:0]
111
(+35.25dB)
Set Maximum Gain of PGA
111 = +35.25dB
110 = +29.25dB
101 = +23.25dB
100 = +17.25dB
011 = +11.25dB
010 = +5.25dB
001 = -0.75dB
000 = -6.75dB
8:7
ALCSEL
00
ALC function select
00 = ALC disabled
01 = Right channel ALC enabled
10 = Left channel ALC enabled
11 = Both channels ALC enabled
R33 (21h)
ALC Control
2
w
3:0
ALCLVL
[3:0]
1011
(-6dB)
ALC target – sets signal level at ADC
input
1111 = -1.5dBFS
1110 = -1.5dBFS
1101 = -3dBFS
1100 = -4.5dBFS
1011 = -6dBFS
1010 = -7.5dBFS
1001 = -9dBFS
1000 = -10.5dBFS
0111 = -12dBFS
0110 = -13.5dBFS
0101 = -15dBFS
0100 = -16.5dBFS
0011 = -18dBFS
0010 = -19.5dBFS
0001 = -21dBFS
0000 = -22.5dBFS
PD, Rev 4.3, May 2010
44
WM8983
Production Data
REGISTER
ADDRESS
BIT
7:4
LABEL
DEFAULT
ALCHLD
0000
[3:0]
(0ms)
DESCRIPTION
ALC hold time before gain is
increased.
0000 = 0ms
0001 = 2.67ms
0010 = 5.33ms
0011 = 10.66ms
0100 = 21.32ms
0101 = 42.64ms
0110 = 85.28ms
0111 = 0.17s
1000 = 0.34s
1001 = 0.68s
1010 = 1.36s
1011 = 2.7s
1100 = 5.4s
1101 = 10.9s
1110 = 21.8 s
1111 = 43.7s
R34 (22h)
ALC Control
3
8
ALCMODE
0
Determines the ALC mode of
operation:
0 = ALC mode (Normal Operation)
1 = Limiter mode.
7:4
ALCDCY
0011
Decay (gain ramp-up) time
[3:0]
(13ms/6dB)
(ALCMODE ==0)
Per
step
Per
6dB
90% of
range
0000
410us
3.3ms
24ms
0001
820us
6.6ms
48ms
0010
1.64ms
13.1ms
192ms
… (time doubles with every step)
1010
or
higher
0011
(2.9ms/6dB)
420ms
3.36s
24.576s
Decay (gain ramp-up) time
(ALCMODE ==1)
Per
step
Per
6dB
90% of
range
0000
90.8us
726.4us
5.26ms
0001
181.6us
1.453ms
10.53m
s
0010
363.2us
2.905ms
21.06m
s
… (time doubles with every step)
1010
3:0
ALCATK
[3:0]
0010
(832us/6dB)
93ms
744ms
5.39s
ALC attack (gain ramp-down) time
(ALCMODE == 0)
Per
step
Per
6dB
90% of
range
0000
104us
832us
6ms
0001
208us
1.66ms
12ms
0010
416us
3.32ms
24.1ms
… (time doubles with every step)
1010
or
higher
w
106ms
852ms
6.18s
PD, Rev 4.3, May 2010
45
WM8983
Production Data
REGISTER
ADDRESS
BIT
LABEL
DEFAULT
DESCRIPTION
0010
ALC attack (gain ramp-down) time
(182us/6dB)
(ALCMODE == 1)
Per
step
Per
6dB
90% of
range
0000
22.7us
182.4us
1.31ms
0001
45.4us
363.2us
2.62ms
0010
90.8us
726.4us
5.26ms
… (time doubles with every step)
1010
23.2ms
186ms
1.348s
Table 19 ALC Control Registers
When the ALC is disabled, the input PGA remains at the last controlled value of the ALC. An input
gain update must be made by writing to the INPPGAVOLL/R register bits.
NORMAL MODE
In normal mode, the ALC will attempt to maintain a constant signal level by increasing or decreasing
the gain of the PGA. The following diagram shows an example of this.
Figure 23 ALC Normal Mode Operation
w
PD, Rev 4.3, May 2010
46
WM8983
Production Data
LIMITER MODE
In limiter mode, the ALC will reduce peaks that go above the threshold level, but will not increase the
PGA gain beyond the starting level. The starting level is the PGA gain setting when the ALC is
enabled in limiter mode. If the ALC is started in limiter mode, this is the gain setting of the PGA at
startup. If the ALC is switched into limiter mode after running in ALC mode, the starting gain will be
the gain at switchover. The diagram below shows an example of limiter mode.
Figure 24 ALC Limiter Mode Operation
ALC LIMITER MODE INITIALISATION SEQUENCE
In order to correctly initialise the ALC in limiter mode, the following sequence of register writes is
required. MCLK must be applied during the initialisation sequence
1. R–5 - Set left input PGA gain (INPPGAVOLL) to level required for operation.
2. R–6 - Set right input PGA gain (INPPGAVOLR) to level required for operation.
3. R–4 - Enable analogue inputs as required.
4. –2 - Disable input PGA (INPPGAEN = 0).
5. R59 = 0x00–3 - Enable ALC test mode.
6. R–2 - Set ALCMAXGAIN and ALCMINGAIN to the level required for operation.
7. R–3 - Set limiter level (ALCLVL) to the level required for operation.
8. R34 = 0x00–0 - Enable ALC mode (ALCMODE = 0).
9. Insert 1ms delay to allow input PGA gain update by the limiter circuit.
w
PD, Rev 4.3, May 2010
47
WM8983
Production Data
10. R34 = 0x01–0 - Enable Limiter mode (ALCMODE = 1).
11. Insert 1ms delay to allow input PGA gain update by the limiter circuit.
12. R59 = 0x00–0 - Turn off ALC test mode.
13. –2 - Enable input PGA (INPPGAENL/R = 1).
Note: R32, R33, R45 and R46 register settings above need to be changed to reflect settings required
in the target application.
ATTACK AND DECAY TIMES
The attack and decay times set the update times for the PGA gain. The attack time is the time
constant used when the gain is reducing. The decay time is the time constant used when the gain is
increasing. In limiter mode, the time constants are faster than in ALC mode. The time constants are
shown below in terms of a single gain step, a change of 6dB and a change of 90% of the PGAs gain
range.
Note that, these times will vary slightly depending on the sample rate used (specified by the SR
register).
NORMAL MODE
ALCMODE = 0 (Normal Mode)
ALCATK
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
tATK
104μs
208μs
416μs
832μs
1.66ms
3.33ms
6.66ms
13.32ms
26.64ms
53.28ms
106.6ms
Attack Time (s)
tATK6dB
tATK90%
832μs
6ms
1.66ms
12ms
3.33ms
24ms
6.66ms
48ms
13.32ms
96ms
26.64ms
192ms
53.28ms
384ms
106.6ms
768ms
213.2ms
1.53s
426.4ms
3.07s
852.8ms
6.14s
ALCMODE = 0 (Normal Mode)
Decay Time (s)
ALCDCY
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
tDCY
410μs
820μs
1.64ms
3.28ms
6.56ms
13.12ms
26.24ms
52.5ms
105ms
210ms
420ms
tDCY6dB
3.3ms
6.6ms
13.1ms
26.2ms
52.5ms
105ms
210ms
420ms
840ms
1.68s
3.36s
tDCY90%
24ms
48ms
96ms
192ms
384ms
768ms
1.53s
3.07s
6.14s
12.28s
24.57s
Table 20 ALC Normal Mode (Attack and Decay times)
w
PD, Rev 4.3, May 2010
48
WM8983
Production Data
LIMITER MODE
ALCMODE = 1 (Limiter Mode)
ALCATK
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
tATKLIM
22.7μs
45.4μS
90.8μS
182μS
363μS
726μS
1.45ms
2.9ms
5.81ms
11.62ms
23.2ms
Attack Time (s)
tATKLIM6dB
tATKLIM90%
182.4μs
1.31ms
363.2μs
2.62ms
726.4μs
5.24ms
1.45ms
10.48ms
2.9ms
20.9ms
5.81ms
41.9ms
11.62ms
83.8ms
23.2ms
167.7ms
46.5ms
335.4ms
93ms
670.8ms
186ms
1.34s
ALCMODE = 1 (Limiter Mode)
ALCDCY
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
tDCYLIM
90.8μs
182μS
363μS
726μS
1.45ms
2.9ms
5.81ms
11.62ms
23.2ms
46.4ms
92.8ms
Attack Time (s)
tDCYLIM6dB
tDCYLIM90%
726.4μs
5.24ms
1.45ms
10.48ms
2.9ms
20.9ms
5.81ms
41.9ms
11.62ms
83.8ms
23.2ms
167.7ms
46.5ms
335.4ms
93ms
670.8ms
186ms
1.34s
372ms
2.68s
744ms
5.36s
Table 21 ALC Limiter Mode (Attack and Decay times)
w
PD, Rev 4.3, May 2010
49
WM8983
Production Data
MINIMUM AND MAXIMUM GAIN
The ALCMIN and ALCMAX register bits set the minimum/maximum gain value that the PGA can be
set to whilst under the control of the ALC. This has no effect on the PGA when ALC is not enabled.
REGISTER
ADDRESS
R32
ALC Control
1
BIT
LABEL
DEFAULT
DESCRIPTION
5:3
ALCMAX
111
Set Maximum Gain of PGA
2:0
ALCMIN
000
Set minimum gain of PGA
Table 22 ALC Max/Min Gain
In normal mode, ALCMAX sets the maximum boost which can be applied to the signal. In limiter
mode, ALCMAX will normally have no effect (assuming the starting gain value is less than the
maximum gain specified by ALCMAX) because the maximum gain is set at the starting gain level.
ALCMIN sets the minimum gain value which can be applied to the signal.
Figure 25 ALC Min/Max Gain
ALCMAX
111
110
101
100
011
010
001
000
Maximum Gain (dB)
35.25
29.25
23.25
17.25
11.25
5.25
-0.75
-6.75
Table 23 ALC Max Gain Values
w
PD, Rev 4.3, May 2010
50
WM8983
Production Data
ALCMIN
000
001
010
011
100
101
110
111
Minimum Gain (dB)
-12
-6
0
6
12
18
24
30
Table 24 ALC Min Gain Values
Note that if the ALC gain setting strays outside the ALC operating range, either by starting the ALC
outside of the range or changing the ALCMAX or ALCMIN settings during operation, the ALC will
immediately adjust the gain to return to the ALC operating range. It is recommended that the ALC
starting gain is set between the ALCMAX and ALCMIN limits.
ALC HOLD TIME (NORMAL MODE ONLY)
In Normal mode, the ALC has an adjustable hold time which sets a time delay before the ALC begins
its decay phase (gain increasing). The hold time is set by the ALCHLD register.
REGISTER
ADDRESS
R33
ALC Control
2
BIT
7:4
LABEL
ALCHLD
DEFAULT
0000
DESCRIPTION
ALC hold time before gain is increased.
Table 25 ALC Hold Time
If the hold time is exceeded this indicates that the signal has reached a new average level and the
ALC will increase the gain to adjust for that new average level. If the signal goes above the threshold
during the hold period, the hold phase is abandoned and the ALC returns to normal operation.
w
PD, Rev 4.3, May 2010
51
WM8983
Production Data
Figure 26 ALCLVL
w
PD, Rev 4.3, May 2010
52
WM8983
Production Data
Figure 27 ALC Hold Time
ALCHLD
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
tHOLD (s)
0
2.67ms
5.34ms
10.7ms
21.4ms
42.7ms
85.4ms
171ms
342ms
684ms
1.37s
Table 26 ALC Hold Time Values
w
PD, Rev 4.3, May 2010
53
WM8983
Production Data
PEAK LIMITER
To prevent clipping when a large signal occurs just after a period of quiet, the ALC circuit includes a
limiter function. If the ADC input signal exceeds 87.5% of full scale (–1.16dB), the PGA gain is
ramped down at the maximum attack rate (as when ALCATK = 0000), until the signal level falls
below 87.5% of full scale. This function is automatically enabled whenever the ALC is enabled.
Note: If ALCATK = 0000, then the limiter makes no difference to the operation of the ALC. It is
designed to prevent clipping when long attack times are used.
NOISE GATE (NORMAL MODE ONLY)
When the signal is very quiet and consists mainly of noise, the ALC function may cause “noise
pumping”, i.e. loud hissing noise during silence periods. The WM8985 has a noise gate function that
prevents noise pumping by comparing the signal level at the input pins against a noise gate
threshold, NGTH. The noise gate cuts in when:
Signal level at ADC [dBFS] < NGTH [dBFS] + PGA gain [dB] + Mic Boost gain [dB]
This is equivalent to:
Signal level at input pin [dBFS] < NGTH [dBFS]
The PGA gain is then held constant (preventing it from ramping up as it normally would when the
signal is quiet).
The table below summarises the noise gate control register. The NGTH control bits set the noise
gate threshold with respect to the ADC full-scale range. The threshold is adjusted in 6dB steps.
Levels at the extremes of the range may cause inappropriate operation, so care should be taken with
set–up of the function. The noise gate only operates in conjunction with the ALC and cannot be used
in limiter mode.
REGISTER
ADDRESS
BIT
R35 (23h)
ALC Noise Gate
2:0
LABEL
NGTH
DEFAULT
000
Control
DESCRIPTION
Noise gate threshold:
000 = -39dB
001 = -45dB
010 = -51db
011 = -57dB
100 = -63dB
101 = -70dB
110 = -76dB
111 = -81dB
3
NGATEN
0
Noise gate function enable
1 = enable
0 = disable
Table 27 ALC Noise Gate Control
w
PD, Rev 4.3, May 2010
54
WM8983
Production Data
The diagrams below show the response of the system to the same signal with and without noise
gate.
Figure 28 ALC Operation Above Noise Gate Threshold
w
PD, Rev 4.3, May 2010
55
WM8983
Production Data
Figure 29 Noise Gate Operation
OUTPUT SIGNAL PATH
The WM8983 output signal paths consist of digital application filters, up-sampling filters, stereo Hi-Fi
DACs, analogue mixers, stereo headphone and stereo line/mono/midrail output drivers. The digital
filters and DAC are enabled by register bits DACENL And DACENR. The mixers and output drivers
can be separately enabled by individual control bits (see Analogue Outputs). Thus it is possible to
utilise the analogue mixing and amplification provided by the WM8983, irrespective of whether the
DACs are running or not.
The WM8983 DACs receive digital input data on the DACDAT pin. The digital filter block processes
the data to provide the following functions:
•
Digital volume control
•
Graphic equaliser
•
A digital peak limiter.
•
Sigma-Delta Modulation
High performance sigma-delta audio DAC converts the digital data into an analogue signal.
Figure 30 DAC Digital Filter Path
w
PD, Rev 4.3, May 2010
56
WM8983
Production Data
The analogue outputs from the DACs can then be mixed with the aux analogue inputs and the ADC
analogue inputs. The mix is fed to the output drivers for headphone (LOUT1/ROUT1,
LOUT2/ROUT2) or line (OUT3/OUT4). OUT3 and OUT4 have additional mixers which allow them to
output different signals to the headphone and line outputs.
DIGITAL PLAYBACK (DAC) PATH
Digital data is passed to the WM8983 via the flexible audio interface and is then passed through a
variety of advanced digital filters as shown in Figure 30 to the hi-fi DACs. The DACs are enabled by
the DACENL/R register bits.
REGISTER
ADDRESS
R3
Power
Management 3
BIT
LABEL
DEFAULT
DESCRIPTION
0
DACENL
0
Left channel DAC enable
0 = DAC disabled
1
DACENR
0
Right channel DAC enable
0 = DAC disabled
1 = DAC enabled
1 = DAC enabled
Table 28 DAC Enable Control
The WM8983 also has a Soft Mute function, which when enabled, gradually attenuates the volume of
the digital signal to zero. When disabled, the gain will ramp back up to the digital gain setting. This
function is enabled by default. To play back an audio signal, it must first be disabled by setting the
SOFTMUTE bit to zero.
REGISTER
ADDRESS
R10
DAC Control
BIT
LABEL
DEFAULT
DESCRIPTION
0
DACPOL
0
Left DAC output polarity:
0 = non-inverted
1
DACRPOL
0
Right DAC output polarity:
0 = non-inverted
2
AMUTE
0
Automute enable
0 = Amute disabled
1 = Amute enabled
3
DACOSR
0
DAC oversampling rate:
0 = 64x (lowest power)
1 = 128x (best performance)
6
SOFTMUTE
0
Softmute enable:
0 = Enabled
1 = Disabled
1 = inverted (180 degrees phase shift)
1 = inverted (180 degrees phase shift)
Table 29 DAC Control Register
The digital audio data is converted to oversampled bit streams in the on-chip, true 24-bit digital
interpolation filters. The bitstream data enters the multi-bit, sigma-delta DACs, which convert it to a
high quality analogue audio signal. The multi-bit DAC architecture reduces high frequency noise and
sensitivity to clock jitter. It also uses a Dynamic Element Matching technique for high linearity and low
distortion.
The DAC output phase defaults to non-inverted. Setting DACLPOL will invert the DAC output phase
on the left channel and DACRPOL inverts the phase on the right channel.
AUTO-MUTE
The DAC has an auto-mute function which applies an analogue mute when 1024 consecutive zeros
are detected. The mute is released as soon as a non-zero sample is detected. Auto-mute can be
disabled using the AMUTE control bit.
w
PD, Rev 4.3, May 2010
57
WM8983
Production Data
DIGITAL HI-FI DAC VOLUME (GAIN) CONTROL
The signal volume from each Hi-Fi DAC can be controlled digitally. The gain range is –127dB to 0dB
in 0.5dB steps. The level of attenuation for an eight-bit code X is given by:
0.5 × (X-255) dB for 1 ≤ X ≤ 255;
REGISTER
ADDRESS
R11
Left DAC
Digital Volume
BIT
7:0
LABEL
MUTE for X = 0
DEFAULT
DESCRIPTION
DACLVOL
11111111
Left DAC Digital Volume Control
[7:0]
( 0dB )
0000 0000 = Digital Mute
0000 0001 = -127dB
0000 0010 = -126.5dB
... 0.5dB steps up to
1111 1111 = 0dB
R12
Right DAC
Digital Volume
8
DACVU
Not
latched
DAC left and DAC right volume do
not update until a 1 is written to
DACVU (in reg 11 or 12)
7:0
DACRVOL
[7:0]
11111111
( 0dB )
Right DAC Digital Volume Control
0000 0000 = Digital Mute
0000 0001 = -127dB
0000 0010 = -126.5dB
... 0.5dB steps up to
1111 1111 = 0dB
8
DACVU
Not
latched
DAC left and DAC right volume do
not update until a 1 is written to
DACVU (in reg 11 or 12)
Table 30 DAC Digital Volume Control
Note: An additional gain of up to 12dB can be added using the gain block embedded in the
digital peak limiter circuit (see DAC OUTPUT LIMITER section).
5-BAND EQUALISER
A 5-band graphic equaliser function which can be used to change the output frequency levels to suit
the environment. This can be applied to the ADC or DAC path and is described in the 5-BAND
EQUALISER section for further details on this feature.
3-D ENHANCEMENT
The WM8983 has an advanced digital 3-D enhancement feature which can be used to vary the
perceived stereo separation of the left and right channels. Like the 5-band equaliser this feature can
be applied to either the ADC record path or the DAC playback path but not both simultaneously.
Refer to the 3-D STEREO ENHANCEMENT section for further details on this feature.
DAC DIGITAL OUTPUT LIMITER
The WM8983 has a digital output limiter function. The operation of this is shown in Figure 31. In this
diagram the upper graph shows the envelope of the input/output signals and the lower graph shows
the gain characteristic.
w
PD, Rev 4.3, May 2010
58
WM8983
Production Data
Figure 31 DAC Digital Limiter Operation
The limiter has a programmable upper threshold which is close to 0dB. Referring to Figure 31, in
normal operation (LIMBOOST=000 => limit only) signals below this threshold are unaffected by the
limiter. Signals above the upper threshold are attenuated at a specific attack rate (set by the LIMATK
register bits) until the signal falls below the threshold. The limiter also has a lower threshold 1dB
below the upper threshold. When the signal falls below the lower threshold the signal is amplified at
a specific decay rate (controlled by LIMDCY register bits) until a gain of 0dB is reached. Both
threshold levels are controlled by the LIMLVL register bits. The upper threshold is 0.5dB above the
value programmed by LIMLVL and the lower threshold is 0.5dB below the LIMLVL value.
VOLUME BOOST
The limiter has programmable upper gain which boosts signals below the threshold to compress the
dynamic range of the signal and increase its perceived loudness. This operates as an ALC function
with limited boost capability. The volume boost is from 0dB to +12dB in 1dB steps, controlled by the
LIMBOOST register bits.
The output limiter volume boost can also be used as a stand alone digital gain boost when the limiter
is disabled.
w
PD, Rev 4.3, May 2010
59
WM8983
Production Data
REGISTER
ADDRESS
R24
DAC digital
limiter control
1
R25
DAC digital
limiter control
2
BIT
LABEL
DEFAULT
3:0
LIMATK
0010
7:4
LIMDCY
0011
8
LIMEN
0
3:0
LIMBOOST
0000
6:4
LIMLVL
000
DESCRIPTION
Limiter Attack time (per 6dB gain
change) for 44.1kHz sampling. Note
that these are proportionally related to
sample rate.
0000 = 94us
0001 = 188s
0010 = 375us
0011 = 750us
0100 = 1.5ms
0101 = 3ms
0110 = 6ms
0111 = 12ms
1000 = 24ms
1001 = 48ms
1010 = 96ms
1011 to 1111 = 192ms
Limiter Decay time (per 6dB gain
change) for 44.1kHz sampling. Note
that these are proportionally related to
sample rate:
0000 = 750us
0001 = 1.5ms
0010 = 3ms
0011 = 6ms
0100 = 12ms
0101 = 24ms
0110 = 48ms
0111 = 96ms
1000 = 192ms
1001 = 384ms
1010 = 768ms
1011 to 1111 = 1.536s
Enable the DAC digital limiter:
0 = disabled
1 = enabled
Limiter volume boost (can be used as a
stand alone volume boost when
LIMEN=0):
0000 = 0dB
0001 = +1dB
0010 = +2dB
0011 = +3dB
0100 = +4dB
0101 = +5dB
0110 = +6dB
0111 = +7dB
1000 = +8dB
1001 = +9dB
1010 = +10dB
1011 = +11dB
1100 = +12dB
1101 to 1111 = reserved
Programmable signal threshold level
(determines level at which the limiter
starts to operate)
000 = -1dB
001 = -2dB
010 = -3dB
011 = -4dB
100 = -5dB
101 to 111 = -6dB
Table 31 DAC Digital Limiter Control
w
PD, Rev 4.3, May 2010
60
WM8983
Production Data
5-BAND GRAPHIC EQUALISER
A 5-band graphic equaliser is provided, which can be applied to the ADC or DAC path, together with
3D enhancement, under control of the EQ3DMODE register bit.
REGISTER
ADDRESS
R18
BIT
8
LABEL
EQ3DMODE
DEFAULT
1
EQ Control 1
DESCRIPTION
0 = Equaliser and 3D Enhancement
applied to ADC path
1 = Equaliser and 3D Enhancement
applied to DAC path
Table 32 EQ and 3D Enhancement DAC or ADC Path Select
Note: The ADCs and DACs must be disabled before changing the EQ3DMODE bit.
The equaliser consists of low and high frequency shelving filters (Band 1 and 5) and three peak filters
for the centre bands. Each has adjustable cut-off or centre frequency, and selectable boost (+/12dB in 1dB steps). The peak filters have selectable bandwidth.
REGISTER
ADDRESS
R18
EQ Band 1
Control
BIT
LABEL
DEFAULT
DESCRIPTION
4:0
EQ1G
01100
(0dB)
Band 1 Gain Control. See Table 38 for
details.
6:5
EQ1C
01
Band 1 Cut-off Frequency:
00 = 80Hz
01 = 105Hz
10 = 135Hz
11 = 175Hz
Table 33 EQ Band 1 Control
REGISTER
ADDRESS
R19
EQ Band 2
Control
BIT
LABEL
DEFAULT
DESCRIPTION
4:0
EQ2G
01100
(0dB)
Band 2 Gain Control. See Table 38 for
details.
6:5
EQ2C
01
8
EQ2BW
0
Band 2 Centre Frequency:
00 = 230Hz
01 = 300Hz
10 = 385Hz
11 = 500Hz
Band 2 Bandwidth Control
0 = narrow bandwidth
1 = wide bandwidth
Table 34 EQ Band 2 Control
REGISTER
ADDRESS
R20
EQ Band 3
Control
BIT
4:0
LABEL
EQ3G
DEFAULT
01100
(0dB)
6:5
EQ3C
01
8
EQ3BW
0
DESCRIPTION
Band 3 Gain Control. See Table 38 for
details.
Band 3 Centre Frequency:
00 = 650Hz
01 = 850Hz
10 = 1.1kHz
11 = 1.4kHz
Band 3 Bandwidth Control
0 = narrow bandwidth
1 = wide bandwidth
Table 35 EQ Band 3 Control
w
PD, Rev 4.3, May 2010
61
WM8983
Production Data
REGISTER
ADDRESS
R21
BIT
4:0
EQ Band 4
Control
LABEL
EQ4G
DEFAULT
01100
(0dB)
6:5
EQ4C
01
8
EQ4BW
0
DESCRIPTION
Band 4 Gain Control. See Table 38 for
details
Band 4 Centre Frequency:
00 = 1.8kHz
01 = 2.4kHz
10 = 3.2kHz
11 = 4.1kHz
Band 4 Bandwidth Control
0 = narrow bandwidth
1 = wide bandwidth
Table 36 EQ Band 4 Control
REGISTER
ADDRESS
BIT
LABEL
DEFAULT
DESCRIPTION
R22
EQ Band 5
4:0
EQ5G
01100
(0dB)
Band 5 Gain Control. See Table 38 for
details.
Gain Control
6:5
EQ5C
01
Band 5 Cut-off Frequency:
00 = 5.3kHz
01 = 6.9kHz
10 = 9kHz
11 = 11.7kHz
Table 37 EQ Band 5 Control
GAIN REGISTER
GAIN
00000
+12dB
00001
+11dB
00010
+10dB
00011
+9dB
00100
+8dB
00101
+7dB
00110
+6dB
00111
+5dB
01000
+4dB
01001
+3dB
01010
+2dB
01011
+1dB
01100
0dB
01101
-1dB
11000
-12dB
11001 to 11111
Reserved
Table 38 Gain Register Table
See also Figure 60 to Figure 77 for equaliser and high pass filter responses.
w
PD, Rev 4.3, May 2010
62
WM8983
Production Data
3D STEREO ENHANCEMENT
The WM8983 has a digital 3D enhancement option to increase the perceived separation between the
left and right channels. Selection of 3D for record or playback is controlled by register bit
EQ3DMODE. Switching this bit from record to playback or from playback to record may only be done
when ADC and DAC are disabled. The WM8983 control interface will only allow EQ3DMODE to be
changed when ADC and DAC are disabled (ie ADCENL = 0, ADCENR = 0, DACENL = 0 and
DACENR = 0).
The DEPTH3D setting controls the degree of stereo expansion.
REGISTER
ADDRESS
R41 (29h)
3D Control
BIT
3:0
LABEL
DEPTH3D[3:0]
DEFAULT
0000
DESCRIPTION
Stereo depth
0000 = Disabled
0001 = 6.67%
0010 = 13.3%
0011 = 20%
0100 = 26.7%
0101 = 33.3%
0110 = 40%
0111 = 46.6%
1000 = 53.3%
1001 = 60%
1010 = 66.7%
1011 = 73.3%
1100 = 80%
1101 = 86.7%
1110 = 93.3%
1111 = 100% (maximum 3D effect)
Table 39 3D Stereo Enhancement Function
Note: When 3D enhancement is used, it may be necessary to attenuate the signal by 6dB to avoid
limiting.
ANALOGUE OUTPUTS
The WM8983 has three sets of stereo analogue outputs. These are:
•
•
•
LOUT1 and ROUT1 which are normally used to drive a headphone load.
LOUT2 and ROUT2 – which can be used as speaker, headphone or line drivers.
OUT3 and OUT4 – can be configured as a stereo line out (OUT3 is left output and
OUT4 is right output). OUT4 can also be used to provide a mono mix of left and
right channels.
The outputs LOUT2, ROUT2 OUT3 and OUT4 are powered from AVDD2 and are capable of driving
a 1V rms signal (AVDD1/3.3) in non-boost mode and AVDD1*1.5/3.3 in boost mode.
LOUT1 and ROUT1 are supplied from AVDD1 and can drive out a 1V rms signal (AVDD1/3.3).
LOUT1, ROUT1, LOUT2 and ROUT2 have individual analogue volume PGAs with -57dB to +6dB
gain ranges.
There are four output mixers in the output signal path, the left and right channel mixers which control
the signals to headphone (and optionally the line outputs) and also dedicated OUT3 and OUT4
mixers.
w
PD, Rev 4.3, May 2010
63
WM8983
Production Data
LEFT AND RIGHT OUTPUT CHANNEL MIXERS
The left and right output channel mixers are shown in Figure 32. These mixers allow the AUX inputs,
the ADC bypass and the DAC left and right channels to be combined as desired. This allows a mono
mix of the DAC channels to be performed as well as mixing in external line-in from the AUX or
speech from the input bypass path.
The AUX and bypass inputs have individual volume control from -15dB to +6dB and the DAC volume
can be adjusted in the digital domain if required. The output of these mixers is connected to the
headphone outputs (LOUT1, ROUT1, LOUT2 and ROUT2) and can optionally be connected to the
OUT3 and OUT4 mixers.
Figure 32 Left/Right Output Channel Mixers
w
PD, Rev 4.3, May 2010
64
WM8983
Production Data
REGISTER
ADDRESS
R43
Output mixer
control
BIT
8
LABEL
BYPL2RMIX
DEFAULT
0
DESCRIPTION
Left bypass path (from the Left
channel input PGA stage) to right
output mixer
0 = not selected
1 = selected
R43
Output mixer
control
7
BYPR2LMIX
0
Right bypass path (from the right
channel input PGA stage) to Left
output mixer
0 = not selected
1 = selected
R49
Output mixer
control
R50
Left channel
output mixer
control
5
DACR2LMIX
0
Right DAC output to left output mixer
0 = not selected
1 = selected
6
DACL2RMIX
0
Left DAC output to right output mixer
0 = not selected
1 = selected
0
DACL2LMIX
1
Left DAC output to left output mixer
0 = not selected
1 = selected
1
BYPL2LMIX
0
Left bypass path (from the left
channel input PGA stage) to left
output mixer
0 = not selected
4:2
BYPLMIXVOL
1 = selected
000
Left bypass volume control to output
channel mixer:
000 = -15dB
001 = -12dB
010 = -9dB
011 = -6dB
100 = -3dB
101 = 0dB
110 = +3dB
111 = +6dB
5
AUXL2LMIX
8:6
AUXLMIXVOL
0
Left Auxilliary input to left channel
output mixer:
0 = not selected
1 = selected
000
Aux left channel input to left mixer
volume control:
000 = -15dB
001 = -12dB
010 = -9dB
011 = -6dB
100 = -3dB
101 = 0dB
110 = +3dB
111 = +6dB
w
PD, Rev 4.3, May 2010
65
WM8983
Production Data
REGISTER
ADDRESS
R51
Right channel
output mixer
control
BIT
0
LABEL
DACR2RMIX
DEFAULT
1
DESCRIPTION
Right DAC output to right output
mixer
0 = not selected
1 = selected
1
BYPR2RMIX
0
Right bypass path (from the right
channel input PGA stage) to right
output mixer
0 = not selected
1 = selected
4:2
BYPRMIXVOL
000
Right bypass volume control to
output channel mixer:
000 = -15dB
001 = -12dB
010 = -9dB
011 = -6dB
100 = -3dB
101 = 0dB
110 = +3dB
111 = +6dB
5
AUXR2RMIX
0
Right Auxiliary input to right channel
output mixer:
0 = not selected
1 = selected
8:6
AUXRMIXVOL
000
Aux right channel input to right mixer
volume control:
000 = -15dB
001 = -12dB
010 = -9dB
011 = -6dB
100 = -3dB
101 = 0dB
110 = +3dB
111 = +6dB
R3
Power
management
3
2
LMIXEN
0
Left output channel mixer enable:
0 = disabled
1 = enabled
3
RMIXEN
0
Right output channel mixer enable:
0 = disabled
1 = enabled
Table 40 Left and Right Output Mixer Control
w
PD, Rev 4.3, May 2010
66
WM8983
Production Data
HEADPHONE OUTPUTS (LOUT1 AND ROUT1)
The headphone outputs LOUT1 and ROUT1 can drive a 16Ω or 32Ω headphone load, either through
DC blocking capacitors, or DC-coupled to a buffered midrail reference as shown in Figure 33. OUT3,
OUT4, LOUT2 or ROUT2 could be used as this buffered reference if one of these outputs is not
being used, saving decoupling capacitors, at the expense of increased power consumption. For fully
independent left and right channels, two separate midrail references can be used, eliminating
crosstalk caused by headphone ground impedances, at the expense of increased power
consumption.
Headphone Output using DC Blocking Capacitors:
Lowest power consumption (Two outputs enabled);
Large and expensive capacitors;
Bass response may be reduced for smaller capacitors;
Impedance in common ground may introduce crosstalk.
DC Coupled Headphone Output:
Higher power consumption (Three outputs enabled);
Improved PSRR if AVDD2 connected to AVDD1;
Impedance in common ground may introduce crosstalk;
Improved bass response (DC connection).
DC Coupled with Fully Independent Left / Right Drive:
Highest power consumption (Four outputs enabled);
Improved PSRR if AVDD2 connected to AVDD1;
Independent L/R pseudo-ground eliminates crosstalk;
Improved bass response (DC connection);
Non-standard headphone connection may not be suitable
for some applications.
Figure 33 Recommended Headphone Output Configurations
Each headphone output has an analogue volume control PGA with a gain range of -57dB to +6dB.
When DC blocking capacitors are used, their capacitance and the load resistance together determine
the lower cut-off frequency of the output signal, fc. Increasing the capacitance lowers fc, improving the
bass response. Smaller capacitance values will diminish the bass response. Assuming a 16Ω load
and C1, C2 = 220μF:
fc = 1 / 2π RLC1 = 1 / (2π x 16Ω x 220μF) = 45 Hz
In the DC coupled configuration, the headphone “ground” is connected to the VMID pin. The OUT3/4
pins can be configured as a DC output driver by setting the OUT3MUTE and OUT4MUTE register bit.
The DC voltage on VMID in this configuration is equal to the DC offset on the LOUT1 and ROUT1
pins therefore no DC blocking capacitors are required. This saves space and material cost in
portable applications.
Note that LOUT2, ROUT2, OUT3 and OUT4 have an optional output boost of 1.5x. When these are
configured in this output boost mode (SPKBOOST/OUT3BOOST/OUT4BOOST=1) then the VMID
value of these outputs will be equal to 1.5xAVDD/2 and will not match the VMID of the headphone
drivers. Do not use the DC coupled output mode in this configuration.
It is recommended to connect the DC coupled outputs only to headphones, and not to the line input
of another device. Although the built-in short circuit protection will prevent any damage to the
headphone outputs, such a connection may be noisy, and may not function properly if the other
device is grounded.
w
PD, Rev 4.3, May 2010
67
WM8983
Production Data
REGISTER
ADDRESS
R52
LOUT1
Volume
control
BIT
7
LABEL
DEFAULT
LOUT1ZC
0
DESCRIPTION
Headphone volume zero cross
enable:
1 = Change gain on zero cross only
0 = Change gain immediately
6
LOUT1MUTE
0
Left headphone output mute:
0 = Normal operation
1 = Mute
5:0
LOUT1VOL
111001
Left headphone output volume:
000000 = -57dB
000001 = -56dB
...
111001 = 0dB
...
111111 = +6dB
R53
ROUT1
Volume
control
8
HPVU
7
ROUT1ZC
Not latched
0
LOUT1 and ROUT1 volumes do not
update until a 1 is written to
OUT1VU (in reg 52 or 53)
Headphone volume zero cross
enable:
1 = Change gain on zero cross only
0 = Change gain immediately
6
ROUT1MUTE
5:0
ROUT1VOL
0
111001
Right headphone output mute:
0 = Normal operation
1 = Mute
Right headphone output volume:
000000 = -57dB
000001 = -56dB
…
111001 = 0dB
...
111111 = +6dB
8
HPVU
Not latched
LOUT1 and ROUT1 volumes do not
update until a 1 is written to
OUT1VU (in reg 52 or 53)
Table 41 OUT1 Volume Control
SPEAKER OUTPUTS (LOUT2 AND ROUT2)
The outputs LOUT2 and ROUT2 are designed to drive an 8Ω BTL speaker but can optionally drive
two headphone loads of 16Ω/32Ω or a line output (see Headphone Output and Line Output sections,
respectively). Each output has an individual volume control PGA, an output boost/level shift bit, a
mute and an enable as shown in Figure 34. LOUT2 and ROUT2 output the left and right channel
mixer outputs respectively.
The ROUT2 signal path also has an optional invert. The amplifier used for this invert can be used to
mix in the AUXR signal with an adjustable gain range of -15dB -> +6dB. This allows a ‘beep’ signal
to be applied only to the speaker output without affecting the HP or line outputs.
w
PD, Rev 4.3, May 2010
68
WM8983
Production Data
Figure 34 Speaker Outputs LOUT2 and ROUT2
w
PD, Rev 4.3, May 2010
69
WM8983
Production Data
SPEAKER BOOST MODE
To support speaker boost mode, AVDD2 should be at least 1.5*AVDD1. A higher AVDD2 will
improve THD performance at the expense of power consumption while lower AVDD2 will cause
clipping.
Variations in AVDD1 and AVDD2 should be taken into account when using speaker boost mode as
shown in Figure 35 and Figure 36.
Figure 35 Non-Boost Mode Output Operation
Figure 36 Boost Mode Output Operation
LOUT2 and ROUT2 outputs can be connected directly to a Lithium battery to improve THD
performance in non-boost mode. When using a 4.2V lithium battery maximum power output is
achieved without using speaker boost and by setting ADVV1 = 3.6V.
Although direct battery connection is also possible in boost mode, the discharge characteristic of the
battery can lead to clipping after a relatively short period of time as shown in Figure 37. Reducing the
maximum permitted volume and keeping AVDD1 to a minimum will allow boost mode to operate for
longer.
Figure 37 Output Boost Mode with Direct Battery Connection
As the full scale output falls close to AVDD1, it becomes more effective to use non-boost mode to
generate a louder output, although SPKBOOST should NOT be changed while the speaker output is
driving out a signal. As a general rule:
if AVD–2 - (AVDD1 * 0.75) > AVDD1 / 2 boost mode provides more power output;
if AVD–2 - (AVDD1 * 0.75) < AVDD1 / 2 non-boost mode provides more power output.
w
PD, Rev 4.3, May 2010
70
WM8983
Production Data
REGISTER
ADDRESS
R54
LOUT2
Volume
control
BIT
LABEL
DEFAULT
DESCRIPTION
LOUT2 volume zero cross enable:
1 = Change gain on zero cross only
0 = Change gain immediately
7
LOUT2ZC
0
6
LOUT2MUTE
0
Left output mute:
0 = Normal operation
1 = Mute
5:0
LOUT2VOL
111001
Left output volume:
000000 = -57dB
000001 = -56dB
...
111001 = 0dB
...
111111 = +6dB
R55
ROUT2
Volume
control
8
SPKVU
7
ROUT2ZC
Not latched
LOUT2 and ROUT2 volumes do not
update until a 1 is written to
OUT2VU (in reg 54 or 55)
0
ROUT2 volume zero cross enable:
1 = Change gain on zero cross only
0 = Change gain immediately
6
ROUT2MUTE
0
Right output mute:
0 = Normal operation
1 = Mute
5:0
ROUT2VOL
111001
Right output volume:
000000 = -57dB
000001 = -56dB
...
111001 = 0dB
...
111111 = +6dB
8
SPKVU
Not latched
LOUT2 and ROUT2 volumes do not
update until a 1 is written to
OUT2VU (in reg 54 or 55)
Table 42 OUT2 Volume Control
The signal output on LOUT2/ROUT2 comes from the Left/Right Mixer circuits and can be any
combination of the DAC output, the Bypass path (output of the input boost stage) and the AUX input.
The LOUT2/ROUT2 volume is controlled by the LOUT2VOL/ ROUT2VOL register bits. Gains over
0dB may cause clipping if the signal is large. The LOUT2MUTE/ ROUT2MUTE register bits cause
the speaker outputs to be muted (the output DC level is driven out). The output pins remain at the
same DC level (DCOP), so that no click noise is produced when muting or un-muting
The speaker output stages also have a selectable gain boost of 1.5x (3.52dB). When this boost is
enabled the output DC level is also level shifted (from AVDD1/2 to 1.5xAVDD1/2) to prevent the
signal from clipping. A dedicated amplifier BUFDCOP, as shown in Figure 34 , is used to perform the
DC level shift operation. This buffer must be enabled using the BUFDCOPEN register bit for this
operating mode. It should also be noted that if AVDD2 is not equal to or greater than 1.5xAVDD1 this
boost mode may result in signals clipping. Table 44 summarises the effect of the SPKBOOST
control bits.
w
PD, Rev 4.3, May 2010
71
WM8983
Production Data
REGISTER
ADDRESS
R49
BIT
2
LABEL
DEFAULT
SPKBOOST
0
0 = speaker gain = -1;
Output control
R1
Power
management
1
DESCRIPTION
DC = AVDD1 / 2
1 = speaker gain = +1.5;
DC = 1.5 x AVDD1 / 2
8
BUFDCOPEN
0
Dedicated buffer for DC level shifting
output stages when in 1.5x gain
boost configuration.
0 = Buffer disabled
1 = Buffer enabled (required for 1.5x
gain boost)
Table 43 Speaker Boost Stage Control
SPKBOOST
OUTPUT
STAGE GAIN
OUTPUT STAGE
CONFIGURATION
OUTPUT DC
LEVEL
0
1x (0dB)
AVDD1/2
Inverting
1
1.5x (3.52dB)
1.5xAVDD1/2
Non-inverting
Table 44 Output Boost Stage Details
REGISTER
ADDRESS
R43
Beep control
BIT
LABEL
DEFAULT
DESCRIPTION
5
MUTERPGA2INV
0
Mute input to INVROUT2 mixer
4
INVROUT2
0
Invert ROUT2 output
3:1
BEEPVOL
000
AUXR input to ROUT2 inverter gain
000 = -15dB
001 = -12dB
010 = -9dB
011 = -6dB
100 = -3dB
101 = 0dB
110 = +3dB
111 = +6dB
0
BEEPEN
0
0 = mute AUXR beep input
1 = enable AUXR beep input
Table 45 AUXR – ROUT2 BEEP Mixer Function
ZERO CROSS TIMEOUT
A zero-cross timeout function is provided so that if zero cross is enabled on the input or output PGAs
the gain will automatically update after a timeout period if a zero cross has not occurred. This is
enabled by setting SLOWCLKEN. The timeout period is dependent on the clock input to the digital
and is equal to 221 * SYSCLK period.
REGISTER
ADDRESS
R7
Additional
Control
BIT
0
LABEL
SLOWCLKEN
DEFAULT
0
DESCRIPTION
Slow clock enable.
0 = slow clock disabled
1 = slow clock enabled
Table 46 Timeout Clock Enable Control
Note: SLOWCLKEN is also used for the jack insert detect debounce circuit
w
PD, Rev 4.3, May 2010
72
WM8983
Production Data
OUT3/OUT4 MIXERS AND OUTPUT STAGES
The OUT3/OUT4 pins provide an additional stereo line output, a mono output, or a pseudo ground
connection for headphones. There is a dedicated analogue mixer for OUT3 and one for OUT4 as
shown in Figure 38.
The OUT3 and OUT4 output stages are powered from AVDD2 and AGND2. These individuallycontrollable outputs also incorporate an optional 1.5x boost and level shifting stage.
Figure 38 OUT3 and OUT4 Mixers
OUT3 can provide a midrail reference, a left line output, or a mono mix line output
OUT4 can provide a midrail reference, a right line output, or a mono mix line output.
A 6dB attenuation function is provided for OUT4, to prevent clipping during mixing of left and right
signals. This function is enabled by the OUT4ATTN register bit.
w
PD, Rev 4.3, May 2010
73
WM8983
Production Data
REGISTER
ADDRESS
R56
OUT3 mixer
control
BIT
LABEL
DEFAULT
6
OUT3MUTE
0
3
OUT4_2OUT3
0
DESCRIPTION
0 = Output stage outputs OUT3 mixer
1 = Output stage muted – drives out
VMID. Can be used as VMID reference
in this mode.
OUT4 mixer output to OUT3
0 = disabled
1 = enabled
2
BYPL2OUT3
0
Left ADC input to OUT3
0 = disabled
1 = enabled
1
LMIX2OUT3
0
Left DAC mixer to OUT3
0 = disabled
0
LDAC2OUT3
1
Left DAC output to OUT3
0 = disabled
7
OUT3_2OUT4
0
6
OUT4MUTE
0
0 = Output stage outputs OUT4 mixer
1 = Output stage muted – drives out
VMID. Can be used as VMID reference
in this mode.
5
OUT4ATTN
0
0 = OUT4 normal output
1 = OUT4 attenuated by 6dB
4
LMIX2OUT4
0
1= enabled
1 = enabled
R57
OUT4 mixer
control
OUT3 mixer output to OUT4
0 = disabled
1= enabled
Left DAC mixer to OUT4
0 = disabled
1 = enabled
3
LDAC2OUT4
0
Left DAC to OUT4
0 = disabled
1 = enabled
2
BYPR2OUT4
0
Right ADC input to OUT4
0 = disabled
1 = enabled
1
RMIX2OUT4
0
0
RDAC2OUT4
1
Right DAC mixer to OUT4
0 = disabled
1 = enabled
Right DAC output to OUT4
0 = disabled
1 = enabled
Table 47 OUT3/OUT4 Mixer Registers
The OUT3 and OUT4 output stages each have a selectable gain boost of 1.5x (3.52dB). When this
boost is enabled the output DC level is also level shifted (from AVDD1/2 to 1.5xAVDD1/2) to prevent
the signal from clipping. A dedicated amplifier BUFDCOP, as shown in Figure 39, is used to perform
the DC level shift operation. This buffer must be enabled using the BUFDCOPEN register bit for this
operating mode. It should also be noted that if AVDD2 is not equal to or greater than 1.5xAVDD1 this
boost mode may result in signals clipping. Table 44 summarises the effect of the OUT3BOOST and
OUT4BOOST control bits.
w
PD, Rev 4.3, May 2010
74
WM8983
Production Data
Figure 39 Outputs OUT3 and OUT4
REGISTER
ADDRESS
R49
Output control
BIT
3
LABEL
DEFAULT
OUT3BOOST
0
DESCRIPTION
0 = OUT3 output gain = -1;
DC = AVDD1 / 2
1 = OUT3 output gain = +1.5
DC = 1.5 x AVDD1 / 2
4
OUT4BOOST
0
0 = OUT4 output gain = -1;
DC = AVDD1 / 2
1 = OUT4 output gain = +1.5
DC = 1.5 x AVDD1 / 2
R1
Power
management
1
8
BUFDCOPEN
Dedicated buffer for DC level shifting
output stages when in 1.5x gain
boost configuration.
0
0=Buffer disabled
1=Buffer enabled (required for 1.5x
gain boost)
Table 48 OUT3 and OUT4 Boost Stages Control
OUT3BOOST/
OUT4BOOST
OUTPUT
STAGE GAIN
OUTPUT DC
LEVEL
OUTPUT STAGE
CONFIGURATIO
N
0
1x
AVDD1/2
Inverting
1
1.5x
1.5xAVDD1/2
Non-inverting
Table 49 OUT3 and OUT4 Output Boost Stage Details
w
PD, Rev 4.3, May 2010
75
WM8983
Production Data
OUTPUT PHASING
The relative phases of the analogue outputs will depend upon the following factors:
1.
DACLPOL and DACRPOL invert bits: Setting these bits to 1 will invert the DAC output.
2.
Mixer configuration: The polarity of the signal will depend upon the route through the mixer path.
For example, DACL can be directly input to the OUT3 mixer, giving a 180° phase shift at the
OUT3 mixer output. However, if DACL is input to the OUT3 mixer via the left mixer, an
additional phase shift will be introduced, giving 0° phase shift at the OUT3 mixer output.
3.
Output boost set-up: When 1.5x boost is enabled on an output, no phase shift occurs. When
1.5x boost is not enabled, a 180° phase shift occurs.
Figure 32 shows where these phase inversions can occur in the output signal path.
Figure 40 Output Signal Path Phasing
w
PD, Rev 4.3, May 2010
76
WM8983
Production Data
Table 50 shows the polarities of the outputs in various configurations.
Unless otherwise stated, polarity is shown with respect to left DAC output in non-inverting mode.
Note that only registers relating to the mixer paths are shown here (Mixer enables, volume settings,
output enables etc are not shown).
0
ROUT2
PHASE / MAG
OUT4BOOST
0
LOUT2
PHASE / MAG
OUT3BOOST
0
ROUT1
PHASE / MAG
SPKBOOST
0
LOUT1
PHASE / MAG
INVROUT2
0
OUT3
PHASE / MAG
DACRPOL
0
Default:
Stereo DAC playback
to LOUT1/ROUT1,
LOUT2/ROUT2 and
MIXER PATH
REGISTERS
DIFFERENT
FROM DEFAULT
OUT4
PHASE / MAG
DACLPOL
CONFIGURATION
0°
0°
0°
0°
180°
180°
1
1
1
1
1
1
180°
180°
180°
0°
0°
OUT4/OUT3
DACs inverted
1
1
0
0
0
0
180°
1
1
1
1
1
1
Stereo DAC playback
to LOUT1/ROUT1 and
LOUT2/ROUT2 and
0
0
0
1
0
0
0°
0°
0°
0°
0°
0°
1
1
1
1
1.5
1.5
180°
180°
0°
0°
180°
180°
1.5
1.5
1
1
1
1
180°
180°
0°
0°
180°
180°
1
1
1
1
1
1
180°
0°
X
X
X
X
1
1
0°
0°
0°
0°
180°
0°
1
1
1
1
1
1
0°
0°
0°
0°
0°
180°
1
1
1
1
1.5
1.5
OUT4/OUT3
(Speaker boost
enabled)
Stereo DAC playback
to LOUT1/ROUT1 and
LOUT2/ROUT2 and
0
0
0
0
1
1
OUT4/OUT3
(OUT3 and OUT4
boost enabled)
Stereo playback to
OUT3/OUT4 (DACs
input to OUT3/OUT4
mixers via left/right
mixers)
0
Differential output of
right bypass path via
OUT3/OUT4 (Phase
shown relative to right
bypass)
0
Differential output of
mono mix of DACs via
LOUT2/ROUT2 (e.g.
BTL speaker drive)
0
High power speaker
drive
0
0
0
0
0
0
LDAC2OUT3=0
RDAC2OUT4=0
LMIX2OUT3=1
RMIX2OUT4=1
0
0
0
0
1
1
0
0
1
0
0
0
0
0
0
BYPR2OUT4=1
OUT4_2OUT3=1
Table 50 Relative Output Phases
Note that differential output should not be set up by combining outputs in boost mode with outputs
which are not in boost mode as this would cause a DC offset current on the outputs.
w
PD, Rev 4.3, May 2010
77
WM8983
Production Data
ENABLING THE OUTPUTS
Each analogue output of the WM8983 can be independently enabled or disabled. The analogue
mixer associated with each output has a separate enable bit. All outputs are disabled by default. To
save power, unused parts of the WM8983 should remain disabled.
Outputs can be enabled at any time, but it is not recommended to do so when BUFIO is disabled
(BUFIOEN=0), as this may cause pop noise (see “Power Management” and “Applications
Information” sections).
REGISTER
ADDRESS
BIT
LABEL
DEFAULT
DESCRIPTION
R1
Power
Management
1
2
BUFIOEN
0
Unused input/output bias buffer enable
6
OUT3MIXEN
0
OUT3 mixer enable
7
OUT4MIXEN
0
OUT4 mixer enable
8
BUFDCOPEN
0
Output stage 1.5xAVDD/2 driver enable
R2
Power
Management
2
8
ROUT1EN
0
ROUT1 output enable
7
LOUT1EN
0
LOUT1 output enable
6
SLEEP
0
0 = Normal device operation
1 = Supply current reduced in device
standby mode if clocks are still running
R3
Power
Management
3
2
LMIXEN
0
Left mixer enable
3
RMIXEN
0
Right mixer enable
5
ROUT2EN
0
ROUT2 output enable
6
LOUT2EN
0
LOUT2 output enable
7
OUT3EN
0
OUT3 enable
8
OUT4EN
0
OUT4 enable
R42
1
DELEN
0
2nd enable bit for L/ROUT1
Output ctrl1
0
OUT1DEL
0
2 stage enable for L/ROUT1
Note: All “Enable” bits are 1 = ON, 0 = OFF
Table 51 Output Stages Power Management Control
OUT1DEL and OUT2DEL enable lower pop noise power-up option. See start–up sequences. (in 2
stage enable method, normal enable bit is set, followed shortly later by the delayed enable DELEN)
THERMAL SHUTDOWN
To protect the WM8983 from overheating a thermal shutdown circuit is included. If the device
temperature reaches approximately 1250C and the thermal shutdown circuit is enabled (TSDEN=1)
the L/ROUT2 amplifiers will be disabled. The thermal shutdown may also be configured to generate
an interrupt. See the GPIO and Interrupt Controller section for details.
REGISTER
ADDRESS
R49
BIT
1
LABEL
TSDEN
Output Control
DEFAULT
1
DESCRIPTION
Thermal Shutdown Enable
0 : thermal shutdown disabled
1 : thermal shutdown enabled
Table 52 Thermal Shutdown
w
PD, Rev 4.3, May 2010
78
WM8983
Production Data
UNUSED ANALOGUE INPUTS/OUTPUTS
Whenever an analogue input/output is disabled, it remains connected to a voltage source (either
AVDD1/2 or 1.5xAVDD1/2 as appropriate) through a resistor. This helps to prevent pop noise when
the output is re-enabled. The resistance between the voltage buffer and the output pins can be
controlled using the VROI control bit. The default impedance is low, so that any capacitors on the
outputs can charge up quickly at start-up. If a high impedance is desired for disabled outputs, VROI
can then be set to 1, increasing the resistance to about 30kΩ.
REGISTER
ADDRESS
R49
BIT
0
LABEL
VROI
DEFAULT
0
DESCRIPTION
VREF (AVDD1/2 or 1.5xAVDD/2) to
analogue output resistance
0: approx 1kΩ
1: approx 30 kΩ
Table 53 Disabled Outputs to VREF Resistance
A dedicated buffer is available for biasing unused analogue I/O pins as shown in Figure 41. This
buffer can be enabled using the BUFIOEN register bit.
If the SPKBOOST, OUT3BOOST or OUT4BOOST bits are set then the relevant outputs will be tied
to the output of the DC level shift buffer at 1.5xAVDD/2 when disabled.
Figure 41 summarises the bias options for the output pins.
Figure 41 Unused Input/Output Pin Tie-off Buffers
w
PD, Rev 4.3, May 2010
79
WM8983
Production Data
VROI
OUTPUT CONFIGURATION
L/ROUT2EN/
OUT3BOOST/
OUT3/4EN
OUT4BOOST/
SPKBOOST
0
0
0
1kΩ tie-off to AVDD1/2
0
0
1
30kΩ tie-off to AVDD1/2
0
1
0
1kΩ tie-off to 1.5xAVDD1/2
0
1
1
30kΩ tie-off to 1.5xAVDD1/2
1
0
X
Output enabled (DC level=AVDD1/2)
1
1
X
Output enabled (DC level=1.5xAVDD1/2)
Table 54 Unused Output Pin Bias Options
DIGITAL AUDIO INTERFACES
The audio interface has four pins:
•
•
ADCDAT: ADC data output
DACDAT: DAC data input
•
•
LRC: Data Left/Right alignment clock
BCLK: Bit clock, for synchronisation
The clock signals BCLK, and LRC can be outputs when the WM8983 operates as a master, or inputs
when it is a slave (see Master and Slave Mode Operation, below).
Five different audio data formats are supported:
•
Left justified
•
•
•
Right justified
I2S
DSP mode early
•
DSP mode late
All of these modes are MSB first. They are described in Audio Data Formats, below. Refer to the
Electrical Characteristic section for timing information.
MASTER AND SLAVE MODE OPERATION
The WM8983 audio interface may be configured as either master or slave. As a master interface
device the WM8983 generates BCLK and LRC and thus controls sequencing of the data transfer on
ADCDAT and DACDAT. To set the device to master mode register bit MS should be set high. In
slave mode (MS=0), the WM8983 responds with data to clocks it receives over the digital audio
interfaces.
AUDIO DATA FORMATS
In Left Justified mode, the MSB is available on the first rising edge of BCLK following an LRC
transition. The other bits up to the LSB are then transmitted in order. Depending on word length,
BCLK frequency and sample rate, there may be unused BCLK cycles before each LRC transition.
Figure 42 Left Justified Audio Interface (assuming n-bit word length)
w
PD, Rev 4.3, May 2010
80
WM8983
Production Data
In Right Justified mode, the LSB is available on the last rising edge of BCLK before a LRC transition.
All other bits are transmitted before (MSB first). Depending on word length, BCLK frequency and
sample rate, there may be unused BCLK cycles after each LRC transition.
Figure 43 Right Justified Audio Interface (assuming n-bit word length)
In I2S mode, the MSB is available on the second rising edge of BCLK following a LRC transition. The
other bits up to the LSB are then transmitted in order. Depending on word length, BCLK frequency
and sample rate, there may be unused BCLK cycles between the LSB of one sample and the MSB of
the next.
2
Figure 44 I S Audio Interface (assuming n-bit word length)
In DSP/PCM mode, the left channel MSB is available on either the 1st (mode B) or 2nd (mode A) rising
edge of BCLK (selectable by LRP) following a rising edge of LRC. Right channel data immediately
follows left channel data. Depending on word length, BCLK frequency and sample rate, there may be
unused BCLK cycles between the LSB of the right channel data and the next sample.
In device master mode, the LRC output will resemble the LRC pulse shown in Figure 45 and Figure
46. In device slave mode, Figure 47 and Figure 48, it is possible to use any length of LRC pulse less
than 1/fs, providing the falling edge of the LRC pulse occurs greater than one BCLK period before the
rising edge of the next LRC pulse.
w
PD, Rev 4.3, May 2010
81
WM8983
Production Data
Figure 45 DSP/PCM Mode Audio Interface (mode A, LRP=0, Master)
Figure 46 DSP/PCM Mode Audio Interface (mode B, LRP=1, Master)
Figure 47 DSP/PCM Mode Audio Interface (mode A, LRP=0, Slave)
w
PD, Rev 4.3, May 2010
82
WM8983
Production Data
Figure 48 DSP/PCM Mode Audio Interface (mode B, LRP=0, Slave)
w
PD, Rev 4.3, May 2010
83
WM8983
Production Data
REGISTER
ADDRESS
R4
Audio
Interface
Control
BIT
0
LABEL
MONO
DEFAULT
0
DESCRIPTION
Selects between stereo and mono
device operation:
0 = Stereo device operation
1 = Mono device operation. Data
appears in ‘left’ phase of LRC.
1
ADCLRSWAP
0
Controls whether ADC data appears in
‘right’ or ‘left’ phases of LRC clock:
0=ADC left data appear in ‘left’ phase of
LRC and right data in 'right' phase
1=ADC left data appear in ‘right ’ phase
of LRC and right data in 'left' phase
2
DACLRSWAP
0
Controls whether DAC data appears in
‘right’ or ‘left’ phases of LRC clock:
0=DAC left data appear in ‘left’ phase of
LRC and right data in 'right' phase
1=DAC left data appear in ‘right’ phase
of LRC and right data in 'left' phase
4:3
FMT
10
Audio interface Data Format Select:
00=Right Justified
01=Left Justified
10=I2S format
11= DSP/PCM mode
6:5
WL
10
Word length
00=16 bits
01=20 bits
10=24 bits
11=32 bits (see note)
7
LRP
0
8
BCP
0
0
LOOPBACK
0
LRC clock polarity
0=normal
1=inverted
BCLK polarity
0=normal
1=inverted
R5
Digital loopback function
0=No loopback
1=Loopback enabled, ADC data output
is fed directly into DAC data input.
Table 55 Audio Interface Control
Note: Right Justified Mode will only operate with a maximum of 24 bits. If 32-bit mode is selected the
device will operate in 24-bit mode.
AUDIO INTERFACE CONTROL
The register bits controlling audio format, word length and master / slave mode are summarised
below.
Register bit MS selects audio interface operation in master or slave mode. In Master mode BCLK and
LRC are outputs. The frequencies of BCLK and LRC in master mode are controlled using MCLKDIV;
these clocks are divided down versions of PLL output clock (SYSCLK). The MCLKDIV default setting
provides a SYSCLK/256 division rate for the LRC output clock.
It is possible to divide down the BCLK rate using BCLKDIV; care must be taken in choosing the
correct BCLKDIV rate to maintain sufficient BCLK pulses per LRC period for the chosen data word
length. The BCLKDIV default setting provides a BCLK = SYSCLK clock.
w
PD, Rev 4.3, May 2010
84
WM8983
Production Data
REGISTER
ADDRESS
R6
Clock
Generation
Control
BIT
0
LABEL
MS
DEFAULT
0
DESCRIPTION
Sets the chip to be master over LRC and
BCLK
0=BCLK and LRC clock are inputs
(Slave mode)
1=BCLK and LRC clock are outputs
generated by the WM8983 (Master
mode)
4:2
BCLKDIV
000
Configures the BCLK and LRC output
frequency, for use when the chip is in
Master mode.
000=divide by 1 (BCLK=SYSCLK)
001=divide by 2 (BCLK=SYSCLK/2)
010=divide by 4
011=divide by 8
100=divide by 16
101=divide by 32
110=reserved
111=reserved
7:5
MCLKDIV
010
Sets the division for either the MCLK or
PLL clock output (selected by CLKSEL)
000=divide by 1
001=divide by 1.5
010=divide by 2 (LRC=SYSCLK/256)
011=divide by 3
100=divide by 4
101=divide by 6
110=divide by 8
111=divide by 12
8
CLKSEL
1
Controls the source of the clock for all
internal operation:
0=MCLK
1=PLL output
Table 56 Clock Control
The CKLSEL bit selects the internal source of the Master clock from the PLL (CLKSEL=1) or from
MCLK (CLKSEL=0). When the internal clock is switched from one source to another using the
CLKSEL bit, the clock originally selected must generate at least one falling edge after the CLKSEL
has changed for the switching of clocks to be successful. For example the sequence for switching
between the PLL and MCLK should be;
w
1.
Change CLKSEL 1 -> 0
2.
Wait for at least one falling edge from PLL generated clock
3.
Disable the PLL (PLLEN=0)
PD, Rev 4.3, May 2010
85
WM8983
Production Data
AUDIO SAMPLE RATES
The WM8983 filter characteristics for the ADCs and the DACs are set using the SR register bits;
these bits do not change the rate of the audio interface output clocks in Master mode. The cut-offs for
the digital filters and the ALC attack/decay times stated are determined using these values and
assume a 256fs master clock rate.
If a sample rate is required which is not explicitly supported by the SR register settings, then the
closest SR value to that sample rate should be chosen, the filter characteristics and the ALC attack,
decay and hold times will scale appropriately.
REGISTER
ADDRESS
R7
Additional
Control
BIT
LABEL
3:1
SR
DEFAULT
000
DESCRIPTION
Approximate sample rate (configures the
coefficients for the internal digital filters):
000 = 48kHz
001 = 32kHz
010 = 24kHz
011 = 16kHz
100 = 12kHz
101 = 8kHz
110-111 = reserved
Table 57 Sample Rate Control
MASTER CLOCK AND PHASE LOCKED LOOP (PLL)
The WM8983 has an on-chip phase-locked loop (PLL) circuit that can be used to:
Generate master clocks for the WM8983 audio functions from another external clock, e.g. in
telecoms applications.
Generate and output (on pin CSB/GPIO1) a clock for another part of the system that is derived from
an existing audio master clock.
Figure 49 shows the PLL and internal clocking on the WM8983.
The PLL can be enabled or disabled by the PLLEN register bit.
REGISTER
ADDRESS
R1
Power
management 1
BIT
5
LABEL
PLLEN
DEFAULT
0
DESCRIPTION
PLL enable
0 = PLL off
1 = PLL on
Table 58 PLLEN Control Bit
w
PD, Rev 4.3, May 2010
86
WM8983
Production Data
Figure 49 PLL and Clock Select Circuit
The PLL frequency ratio R = f2/f1 (see Figure 49) can be set using the register bits PLLK and PLLN.
R should be chosen to ensure 5 < PLLN < 13:
PLLN = int R
PLLK = int (224 (R-PLLN))
To calculate R:
There is a fixed divide by 4 in the PLL, f/4, and a selectable divide by N after the PLL, MCLKDIV.
•
f2 = SYSCLK x 4 x MCLKDIV
•
R = f2 / (MCLK / PRESCALE) = R
•
PLLN = int R
•
k = int ( 224 x (R – intR)) – convert k to hex for PLLK
EXAMPLE:
MCLK=26MHz, required clock = 12.288MHz.
R should be chosen to ensure 5 < PLLN < 13.
MCLKDIV = 2 sets the required division rate;
•
f2 = 4 x 2 x 12.288MHz = 98.304MHz.
•
R = 98.304 / (26/2) = 7.561846
•
PLLN = int R = 7
•
k = int ( 224 x (7.561846 – 7)) = 9426214dec
Convert k to hex:
PLLK = 8FD526h
Convert PLLK to R36, R37, R38 and R39 hex values:
R36 = 7h; R37 = 23h; R38 = 1EAh; R39 = 126h
w
PD, Rev 4.3, May 2010
87
WM8983
Production Data
REGISTER
ADDRESS
R36
PLL N value
BIT
LABEL
DEFAULT
DESCRIPTION
4
PLLPRESCALE
0
0 = MCLK input not divided (default)
1 = Divide MCLK by 2 before input
to PLL
3:0
PLLN
1000
Integer (N) part of PLL input/output
frequency ratio. Use values greater
than 5 and less than 13.
R37
PLL K value
1
5:0
PLLK [23:18]
0Ch
Fractional (K) part of PLL1
input/output frequency ratio (treat as
one 24-digit binary number).
R38
PLL K Value
2
8:0
PLLK [17:9]
093h
R39
PLL K Value
3
8:0
PLLK [8:0]
0E9h
Table 59 PLL Frequency Ratio Control
The PLL performs best when f2 is around 90MHz. Its stability peaks at N=8. Some example settings
are shown in Table 60.
DESIRED
OUTPUT
(MHz)
F2
PRESCALE
(MHz)
DIVIDE
12
11.29
90.3168
1
2
7.5264
7
12
12.288
98.304
1
2
8.192
8
13
11.29
90.3168
1
2
6.947446
13
12.288
98.304
1
2
7.561846
14.4
11.29
90.3168
1
2
6.272
14.4
12.288
98.304
1
2
19.2
11.29
90.3168
2
2
19.2
12.288
98.304
2
19.68
11.29
90.3168
19.68
12.288
19.8
19.8
24
24
26
11.29
90.3168
2
2
26
12.288
98.304
2
2
27
11.29
90.3168
2
2
27
12.288
98.304
2
2
MCLK
(MHz)
(F1)
MCLKDIV
R
PLLN
K
PLLK
PLLK
R36
(Hex)
[23:18]
[17:9]
[8:0]
R37 (Hex)
R38 (Hex)
R39 (Hex)
86C226
21
161
26
3126E8
C
93
E9
6
F28BD4
3C
145
1D4
7
8FD525
23
1EA
126
6
45A1CA
11
D0
1CA
6.826667
6
D3A06E
34
1D0
6D
9.408
9
6872AF
1A
39
B0
2
10.24
A
3D70A3
F
B8
A3
2
2
9.178537
9
2DB492
B
DA
92
98.304
2
2
9.990243
9
FD809F
3F
C0
9F
11.29
90.3168
2
2
9.122909
9
1F76F7
7
1BB
F8
12.288
98.304
2
2
9.929697
9
EE009E
3B
100
9E
11.29
90.3168
2
2
7.5264
7
86C226
21
161
26
12.288
98.304
2
2
8.192
8
3126E8
C
93
E9
6.947446
6
F28BD4
3C
145
1D4
7.561846
7
8FD525
23
1EA
126
6.690133
6
BOAC93
2C
56
94
7.281778
7
482296
12
11
96
(Hex)
PLLK
Table 60 PLL Frequency Examples for Common MCLK Rates
LOOPBACK
Setting the LOOPBACK register bit enables digital loopback. When this bit is set the output data
from the ADC audio interface is fed directly into the DAC data input.
w
PD, Rev 4.3, May 2010
88
WM8983
Production Data
COMPANDING
The WM8983 supports A-law and μ-law companding on both transmit (ADC) and receive (DAC)
sides. Companding can be enabled on the DAC or ADC audio interfaces by writing the appropriate
value to the DAC_COMP or ADC_COMP register bits respectively.
REGISTER
ADDRESS
R5
Companding
Control
BIT
2:1
LABEL
DEFAULT
ADC_COMP
0
DESCRIPTION
ADC companding
00 = off
01 = reserved
10 = μ-law
11 = A-law
4:3
DAC_COMP
0
DAC companding
00 = off
01 = reserved
10 = μ-law
11 = A-law
5
WL8
0
0 = off
1 = device operates in 8-bit mode.
Table 61 Companding Control
Companding involves using a piecewise linear approximation of the following equations (as set out
by ITU-T G.711 standard) for data compression:
μ-law (where μ=255 for the U.S. and Japan):
F(x) = ln( 1 + μ|x|) / ln( 1 + μ)
-1 ≤ x ≤ 1
law (where A=87.6 for Europe):
F(x) = A|x| / ( 1 + lnA)
} for x ≤ 1/A
F(x) = ( 1 + lnA|x|) / (1 + lnA)
} for 1/A ≤ x ≤ 1
The companded data is also inverted as recommended by the G.711 standard (all 8 bits are inverted
for μ-law, all even data bits are inverted for A-law). The data will be transmitted as the first 8 MSB’s
of data.
Companding converts 13 bits (μ-law) or 12 bits (A-law) to 8 bits using non-linear quantization. The
input data range is separated into 8 levels, allowing low amplitude signals better precision than that
of high amplitude signals. This is to exploit the operation of the human auditory system, where
louder sounds do not require as much resolution as quieter sounds. The companded signal is an 8bit word containing sign (1-bit), exponent (3-bits) and mantissa (4-bits).
Setting the WL8 register bit allows the device to operate with 8-bit data. In this mode it is possible to
use 8 BCLK’s per LRC frame. When using DSP mode B, this allows 8-bit data words to be output
consecutively every 8 BCLK’s and can be used with 8-bit data words using the A-law and u-law
companding functions.
BIT7
BIT[6:4]
BIT[3:0]
SIGN
EXPONENT
MANTISSA
Table 62 8-bit Companded Word Composition
w
PD, Rev 4.3, May 2010
89
WM8983
Production Data
u-law Companding
1
120
0.9
Companded Output
0.7
80
0.6
0.5
60
0.4
40
0.3
Normalised Output
0.8
100
0.2
20
0.1
0
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Normalised Input
Figure 50 μ-Law Companding
A-law Companding
1
120
0.9
Companded Output
0.7
80
0.6
0.5
60
0.4
40
0.3
Normalised Output
0.8
100
0.2
20
0.1
0
0
0
0.2
0.4
0.6
0.8
1
Normalised Input
Figure 51 A-Law Companding
w
PD, Rev 4.3, May 2010
90
WM8983
Production Data
GENERAL PURPOSE INPUT/OUTPUT
The WM8983 has three dual purpose input/output pins.
•
CSB/GPIO1: CSB / GPIO1 pin
•
L2/GPIO2: Left channel line input / headphone detection input
•
R2/GPIO3: Right channel line input / headphone detection input
The GPIO2 and GPIO3 functions are provided for use as jack detection inputs.
The GPIO1 and GPIO2 functions are provided for use as jack detection inputs or general purpose
outputs.
The default configuration for the CSB/GPIO1 is to be an input.
When setup as an input, the CSB/GPIO1 pin can either be used as CSB or for jack detection,
depending on how the MODE pin is set.
Table 63 illustrates the functionality of the GPIO1 pin when used as a general purpose output.
REGISTER
ADDRESS
R8
GPIO
Control
BIT
2:0
LABEL
GPIO1SEL
DEFAULT
000
DESCRIPTION
CSB/GPIO1 pin function select:
000= input (CSB/jack detection:
depending on MODE setting)
001 = reserved
010 = Temp ok
011 = Amute active
100 = PLL clk output
101 = PLL lock
110 = logic 0
111 = logic 1
3
GPIO1POL
0
GPIO1 Polarity invert
0 = Non inverted
1 = Inverted
5:4
OPCLKDIV
00
PLL Output clock division ratio
00 = divide by 1
01 = divide by 2
10 = divide by 3
11 = divide by 4
Table 63 CSB/GPIO Control
Note: If MODE is set to 3 wire mode, CSB/GPIO1 is used as CSB input irrespective of the
GPIO1SEL[2:0] bits.
For further details of the jack detect operation see the OUTPUT SWITCHING section.
OUTPUT SWITCHING (JACK DETECT)
When the device is operated using a 2-wire interface the CSB/GPIO1 pin can be used as a switch
control input to automatically disable one set of outputs and enable another; the most common use
for this functionality is as jack detect circuitry. The L2/GPIO2 and R2/GPIO3 pins can also be used
for this purpose.
The GPIO pins have an internal de-bounce circuit when in this mode in order to prevent the output
enables from toggling multiple times due to input glitches. This de-bounce circuit is clocked from a
slow clock with period 221 x MCLK and is enabled by the SLOWCLKEN bit.
Notes:
w
1.
The SLOWCLKEN bit must be enabled for the jack detect circuitry to operate.
2.
The GPIOPOL bit is not relevant for jack detection, it is the signal detected at the pin which is
used.
PD, Rev 4.3, May 2010
91
WM8983
Production Data
Switching on/off of the outputs is fully configurable by the user. Each output, OUT1, OUT2, OUT3
and OUT4 has 2 associated enables. OUT1_EN_0, OUT2_EN_0, OUT3_EN_0 and OUT4_EN_0 are
the output enable signals which are used if the selected jack detection pin is at logic 0 (after debounce). OUT1_EN_1, OUT2_EN_1, OUT3_EN_1 and OUT4_EN_1 are the output enable signals
which are used if the selected jack detection pin is at logic 1 (after de-bounce).
The jack detection enables operate as follows:
All OUT_EN signals have an AND function performed with their normal enable signals (in Table 51).
When an output is normally enabled at per Table 51, the selected jack detection enable (controlled
by selected jack detection pin polarity) is set 0; it will turn the output off. If the normal enable signal is
already OFF (0), the jack detection signal will have no effect due to the AND function.
During jack detection if the user desires an output to be un-changed whether the jack is in or not,
both the JD_EN settings, i.e. JD_EN0 and JD_EN1, should be set to 0000.
If jack detection is not enabled (JD_EN=0), the output enables default to all 1’s, allowing the outputs
to be controlled as normal via the normal output enables found in Table 51.
BIT
LABEL
DEFAULT
DESCRIPTION
REGISTER
ADDRESS
R9 (09h)
5:4
JD_SEL
00
GPIO control
Pin selected as jack detection input
00 = GPIO1
01 = GPIO2
10 = GPIO3
11 = Reserved
6
JD_EN
0
Jack Detection Enable
0 = disabled
3:0
JD_EN0
0000
Output enables when selected jack
detection input is logic 0.
1 = enabled
R13 (0Dh)
[0]= OUT1_EN_0
[1]= OUT2_EN_0
[2]= OUT3_EN_0
[3]= OUT4_EN_0
7:4
JD_EN1
0000
Output enables when selected jack
detection input is logic 1
[4]= OUT1_EN_1
[5]= OUT2_EN_1
[6]= OUT3_EN_1
[7]= OUT4_EN_1
Table 64 Jack Detect Register Control Bits
w
PD, Rev 4.3, May 2010
92
WM8983
Production Data
CONTROL INTERFACE
SELECTION OF CONTROL MODE AND 2-WIRE MODE ADDRESS
The control interface can operate as either a 3-wire or 2-wire control interface. The MODE pin
determines the 2 or 3 wire mode as shown in Table 65.
The WM8983 is controlled by writing to registers through a serial control interface. A control word
consists of 16 bits. The first 7 bits (B15 to B9) are register address bits that select which control
register is accessed. The remaining 9 bits (B8 to B0) are data bits, corresponding to the 9 data bits in
each control register.
MODE
INTERFACE FORMAT
Low
2 wire
High
3 wire
Table 65 Control Interface Mode Selection
3-WIRE SERIAL CONTROL MODE
In 3-wire mode, every rising edge of SCLK clocks in one data bit from the SDIN pin. A rising edge on
CSB/GPIO latches in a complete control word consisting of the last 16 bits.
Figure 52 3-Wire Serial Control Interface
2-WIRE SERIAL CONTROL MODE
The WM8983 supports software control via a 2-wire serial bus. Many devices can be controlled by
the same bus, and each device has a unique 7-bit device address (this is not the same as the 7-bit
address of each register in the WM8983).
The WM8983 operates as a slave device only. The controller indicates the start of data transfer with
a high to low transition on SDIN while SCLK remains high. This indicates that a device address and
data will follow. All devices on the 2-wire bus respond to the start condition and shift in the next eight
bits on SDIN (7-bit address + Read/Write bit, MSB first). If the device address received matches the
address of the WM8983, the WM8983 responds by pulling SDIN low on the next clock pulse (ACK). If
the address is not recognised or the R/W bit is ‘1’ when operating in write only mode, the WM8983
returns to the idle condition and waits for a new start condition and valid address.
During a write, once the WM8983 has acknowledged a correct address, the controller sends the first
byte of control data (B15 to B8, i.e. the WM8983 register address plus the first bit of register data).
The WM8983 then acknowledges the first data byte by driving SDIN low for one clock cycle. The
controller then sends the second byte of control data (B7 to B0, i.e. the remaining 8 bits of register
data), and the WM8983 acknowledges again by pulling SDIN low.
Transfer is complete when there is a low to high transition on SDIN while SCLK is high. After a
complete sequence the WM8983 returns to the idle state and waits for another start condition. If a
start or stop condition is detected out of sequence at any point during data transfer (i.e. SDIN
changes while SCLK is high), the control interface returns to the idle condition.
DEVICE ADDRESS
(7 BITS)
SDIN
RD / WR
BIT
ACK
(LOW)
CONTROL BYTE 1
(BITS 15 TO 8)
ACK
(LOW)
CONTROL BYTE 1
(BITS 7 TO 0)
ACK
(LOW)
SCLK
START
register address and
1st register data bit
remaining 8 bits of
register data
STOP
Figure 53 2-Wire Serial Control Interface
In 2-wire mode the WM8983 has a fixed device address, 0011010.
w
PD, Rev 4.3, May 2010
93
WM8983
Production Data
RESETTING THE CHIP
The WM8983 can be reset by performing a write of any value to the software reset register (address
0h). This will cause all register values to be reset to their default values. In addition to this there is a
Power-On Reset (POR) circuit which ensures that the registers are initially set to default when the
device is powered up.
POWER SUPPLIES
The WM8983 requires four separate power supplies:
AVDD1 and AGND1: Analogue supply, powers all internal analogue functions and output drivers
LOUT1 and ROUT1. AVDD1 must be between 2.5V and 3.6V and has the most significant impact on
overall power consumption (except for power consumed in the headphones). Higher AVDD1 will
improve audio quality.
AVDD2 and AGND2: Output driver supplies, power LOUT2, ROUT2, OUT3 and OUT4. AVDD2 must
be between 2.5V and 5.5V. AVDD2 can be tied to AVDD1, but it requires separate layout and
decoupling capacitors to curb harmonic distortion.
DCVDD: Digital core supply, powers all digital functions except the audio and control interfaces.
DCVDD must be between 1.71V and 3.6V, and has no effect on audio quality. The return path for
DCVDD is DGND, which is shared with DBVDD.
DBVDD must be between 1.71V and 3.6V. DBVDD return path is through DGND.
It is possible to use the same supply voltage for all four supplies. However, digital and analogue
supplies should be routed and decoupled separately on the PCB to keep digital switching noise out
of the analogue signal paths.
POWER MANAGEMENT
SAVING POWER BY REDUCING OVERSAMPLING RATE
The default mode of operation of the ADC and DAC digital filters is in 64x oversampling mode. Under
the control of ADCOSR128 and DACOSR128 the oversampling rate may be doubled. 64x
oversampling results in a slight decrease in noise performance compared to 128x but lowers the
power consumption of the device.
REGISTER
ADDRESS
R10
BIT
3
LABEL
DACOSR128
DEFAULT
0
DAC control
R14
DESCRIPTION
DAC oversample rate select
0 = 64x (lowest power)
1 = 128x (best SNR)
3
ADCOSR128
0
ADC control
ADC oversample rate select
0 = 64x (lowest power)
1 = 128x (best SNR)
Table 66 ADC and DAC Oversampling Rate Selection
VMID
The analogue circuitry will not operate unless VMID is enabled. The impedance of the VMID resistor
string, together with the decoupling capacitor on the VMID pin will determine the start-up time of the
VMID circuit.
REGISTER
ADDRESS
R1
Power
management 1
BIT
1:0
LABEL
VMIDSEL
DEFAULT
00
DESCRIPTION
Reference string impedance to VMID pin
(Determines startup time):
00 = off (250kΩ VMID to AGND1)
01 = 100kΩ
10 = 500kΩ
11 = 10kΩ total (for fast start-up)
Table 67 VMID Impedance Control
w
PD, Rev 4.3, May 2010
94
WM8983
Production Data
BIASEN
The analogue amplifiers will not operate unless BIASEN is enabled.
REGISTER
ADDRESS
R1
Power
management 1
BIT
3
LABEL
BIASEN
DEFAULT
0
DESCRIPTION
Analogue amplifier bias control
0 = disabled
1 = enabled
Table 68 Analogue Bias Control
BIAS CONTROL
Control of the analog bias values is possible using register 61 and 62
REGISTER
ADDRESS
R61
Bias control
BIT
8
LABEL
BIASCUT
DEFAULT
0
DESCRIPTION
Global bias control
0 = normal
1 = 0.5x
7:0
000 0000
Reserved
Table 69 Analogue Bias Control
Note that these bits must be used with care and may cause degradation in analog performance. For
example, if both BIASCUT and HALFDACI are used at same time, the playback THD will be poor.
w
PD, Rev 4.3, May 2010
95
WM8983
Production Data
REGISTER MAP
ADDR
B[15:9]
REGISTER
NAME
B8
B7
B6
B5
B4
B3
B2
B1
B0
DEF’T
VAL
D
E
C
H
E
X
0
00
Software Reset
1
01
Power manage’t
1
BUFDC
OPEN
OUT4
MIXEN
OUT3
MIXEN
PLLEN
MICBEN
BIASEN
BUFIO
EN
2
02
Power manage’t
2
ROUT1
LOUT1
SLEEP
BOOST
BOOST
INPGA
INPPGA
ADC
ADC
EN
EN
ENR
ENL
ENR
ENL
ENR
ENL
ROUT2
EN
0
RMIXEN
LMIXEN
DAC
ENR
DAC
ENL
000
DLR
ALR
MONO
050
SWAP
SWAP
LOOP
BACK
000
MS
140
SLOWC
LK
000
(HEX)
Software reset
3
03
Power manage’t
3
OUT4EN
OUT3EN
4
04
Audio Interface
BCP
LRP
LOUT2
EN
WL[1:0]
FMT[1:0]
VMIDSEL[1:0]
000
000
5
05
Companding ctrl
6
06
Clock Gen ctrl
CLKSEL
7
07
Additional ctrl
0
0
0
8
08
GPIO Control
0
0
0
OPCLKDIV[1:0]
GPIO1P
OL
9
09
Jack detect
control
0
0
JD_EN
JD_SEL[1:0]
0
0
0
0
000
10
0A
DAC Control
0
0
SOFT
MUTE
0
DAC
OSR128
AMUTE
DACR
POL
DACL
POL
000
11
0B
Left DAC digital
Vol
DACVU
DACLVOL[7:0]
0FF
12
0C
Right DAC dig’l
Vol
DACVU
DACRVOL[7:0]
0FF
13
0D
Jack Detect
Control
0
14
0E
ADC Control
HPFEN
15
0F
Left ADC Digital
Vol
ADCVU
ADCLVOL[7:0]
0FF
16
10
Right ADC Digital
Vol
ADCVU
ADCRVOL[7:0]
0FF
18
12
EQ1 – low shelf
0
0
0
WL8
DAC_COMP[1:0]
MCLKDIV[2:0]
ADC_COMP[1:0]
BCLKDIV[2:0]
0
0
0
SR[2:0]
EN
0
JD_EN1[3:0]
HPFAPP
EQ3D
000
GPIO1SEL[2:0]
000
JD_EN0[3:0]
HPFCUT[2:0]
ADC
OSR128
0
ADCR
POL
ADC
LPOL
100
0
EQ1C[1:0]
EQ1G[4:0]
12C
MODE
19
13
EQ2 – peak 1
EQ2BW
0
EQ2C[1:0]
EQ2G[4:0]
02C
20
14
EQ3 – peak 2
EQ3BW
0
EQ3C[1:0]
EQ3G[4:0]
02C
21
15
EQ4 – peak 3
EQ4BW
0
EQ4C[1:0]
EQ4G[4:0]
02C
22
16
EQ5 – high shelf
0
0
EQ5C[1:0]
EQ5G[4:0]
02C
24
18
DAC Limiter 1
LIMEN
25
19
DAC Limiter 2
0
0
27
1B
Notch Filter 1
NFU
NFEN
NFA0[13:7]
000
28
1C
Notch Filter 2
NFU
0
NFA0[6:0]
000
29
1D
Notch Filter 3
NFU
0
NFA1[13:7]
000
30
1E
Notch Filter 4
NFU
0
NFA1[6:0]
32
20
ALC control 1
33
21
ALC control 2
34
22
ALC control 3
LIMDCY[3:0]
ALCSEL
LIMLVL[2:0]
0
ALCMAX[2:0]
LIMATK[3:0]
032
LIMBOOST[3:0]
000
000
ALCMIN[2:0]
038
0
ALCHLD[3:0]
ALCLVL[3:0]
00B
ALC
ALCDCY[3:0]
ALCATK[3:0]
032
MODE
w
PD, Rev 4.3, May 2010
96
WM8983
Production Data
ADDR
B[15:9]
REGISTER
NAME
B8
B7
B6
B5
B4
B3
B2
B1
B0
DEF’T
VAL
D
E
C
H
E
X
35
23
Noise Gate
0
0
0
0
0
36
24
PLL N
0
0
0
0
PLLPRE
SCALE
37
25
PLL K 1
0
0
0
38
26
PLL K 2
PLLK[17:9]
093
39
27
PLL K 3
PLLK[8:0]
0E9
41
29
3D control
42
2A
43
2B
Beep control
44
2C
45
46
(HEX)
NGEN
000
NGTH[2:0]
008
PLLN[3:0]
00C
PLLK[23:18]
000
DEPTH3D[3:0]
OUT4 to ADC
OUT4_2ADCVOL[2:0]
OUT4_2
0
0
POB
LNR
DELEN
OUT1
CTRL
DEL
BEEPVOL[2:0]
BEEP
EN
000
LIP2
INPPGA
033
BYPL2
RMIX
BYPR2
LMIX
0
MUTER
PGA2IN
V
INVROUT2
Input ctrl
MBVSEL
0
R2_2
INPPGA
RIN2
INPPGA
RIP2
INPPGA
2D
Left INP PGA
gain ctrl
INPGAVU
INPPGA
ZCL
INPPGA
MUTEL
INPPGAVOLL[5:0]
010
2E
Right INP PGA
gain ctrl
INPGAVU
INPPGA
INPPGA
INPPGAVOLR[5:0]
010
ZCR
MUTER
0
L2_2
INPPGA
LIN2
INPPGA
47
2F
Left ADC Boost
ctrl
PGA
BOOSTL
0
L2_2BOOSTVOL[2:0]
0
AUXL2BOOSTVOL[2:0]
100
48
30
Right ADC Boost
ctrl
PGA
0
R2_2BOOSTVOL[2:0]
0
AUXR2BOOSTVOL[2:0]
100
BOOSTR
49
31
Output ctrl
50
32
Left mixer ctrl
0
0
DACL2
RMIX
AUXLMIXVOL[2:0]
DACR2
LMIX
OUT4
BOOST
AUXL2
OUT3
BOOST
SPK
BOOST
BYPLMIXVOL[2:0]
LMIX
TSDEN
VROI
002
BYPL2
DACL2
001
LMIX
LMIX
BYPR2
RMIX
DACR2
RMIX
51
33
Right mixer ctrl
52
34
LOUT1 (HP)
volume ctrl
OUT1VU
LOUT1
ZC
LOUT1
MUTE
LOUT1VOL[5:0]
039
53
35
ROUT1 (HP)
volume ctrl
OUT1VU
ROUT1
ZC
ROUT1
MUTE
ROUT1VOL[5:0]
039
54
36
LOUT2 (SPK)
volume ctrl
OUT2VU
LOUT2
ZC
LOUT2
MUTE
LOUT2VOL[5:0]
039
55
37
ROUT2 (SPK)
volume ctrl
OUT2VU
ROUT2
ROUT2
ROUT2VOL[5:0]
039
ZC
MUTE
OUT3
MUTE
0
0
OUT4_
2OUT3
BYPL2
OUT3
LMIX2
OUT3
LDAC2
OUT3
001
OUT4
OUT4
LMIX2
LDAC2
BYPR2
RMIX2
RDAC2
001
MUTE
ATTN
OUT4
OUT4
OUT4
OUT4
OUT4
AUXRMIXVOL[2:0]
56
38
OUT3 mixer ctrl
0
0
57
39
OUT4 (MONO)
mixer ctrl
0
OUT3_2
OUT4
59
3B
ALC Test Mode
61
3D
Bias Control
AUXR2
RMIX
BYPRMIXVOL[2:0]
000 0000
BIASCUT
ALCTST[1:0]
0000 0000
001
000
000
Table 70 WM8983 Register Map
w
PD, Rev 4.3, May 2010
97
WM8983
Production Data
REGISTER BITS BY ADDRESS
Notes:
1. Default values of N/A indicate non-latched data bits (e.g. software reset or volume update bits).
2. Register bits marked “s "Reser”ed" should not be changed from the default.
REGISTER
ADDRESS
BIT
LABEL
DEFAULT
DESCRIPTION
REFER TO
0 (00h)
[8:0]
RESET
N/A
Software reset
Resetting the
Chip
1 (01h)
8
BUFDCOPEN
0
Dedicated buffer for DC level shifting output
stages when in 1.5x gain boost configuration.
0 = Buffer disabled
Analogue
Outputs
7
OUT4MIXEN
0
OUT4 mixer enable
0=disabled
6
OUT3MIXEN
0
OUT3 mixer enable
0=disabled
1=enabled
Power
Management
5
PLLEN
0
PLL enable
0=PLL off
1=PLL on
Master Clock
and Phase
Locked Loop
(PLL)
4
MICBEN
0
Microphone Bias Enable
Input Signal
Path
1 = Buffer enabled (required for 1.5x gain boost)
Power
Management
1=enabled
0 = OFF (high impedance output)
1 = ON
3
BIASEN
0
2
BUFIOEN
0
1:0
VMIDSEL
00
Power
Management
Analogue amplifier bias control
0=disabled
1=enabled
Power
Management
Unused input/output tie off buffer enable
0=disabled
1=enabled
Reference string impedance to VMID pin
(Determines startup time):
Power
Management
00 = off (250kΩ VMID to AGND1)
01 = 100kΩ
10 = 500kΩ
11 = 10kΩ total (for fast start-up)
2 (02h)
8
ROUT1EN
0
Power
Management
ROUT1 output enable
0=disabled
1=enabled
Power
Management
7
LOUT1EN
0
LOUT1 output enable
0=disabled
6
SLEEP
0
0 = normal device operation
1 = residual current reduced in device standby
mode
Power
Management
5
BOOSTENR
0
Right channel Input BOOST enable
Power
Management
1=enabled
0 = Boost stage OFF
1 = Boost stage ON
4
BOOSTENL
0
Left channel Input BOOST enable
0 = Boost stage OFF
1 = Boost stage ON
w
Power
Management
PD, Rev 4.3, May 2010
98
WM8983
Production Data
REGISTER
ADDRESS
BIT
3
LABEL
INPPGAENR
DEFAULT
0
DESCRIPTION
REFER TO
Right channel input PGA enable
Power
Management
0 = disabled
1 = enabled
2
INPPGAENL
0
1
ADCENR
0
Left channel input PGA enable
0 = disabled
Power
Management
1 = enabled
Enable ADC right channel:
0 = ADC disabled
1 = ADC enabled
R3 (03h)
Analogue to
Digital
Converter
(ADC)
0
ADCENL
0
Enable ADC left channel:
0 = ADC disabled
1 = ADC enabled
Analogue to
Digital
Converter
(ADC)
8
OUT4EN
0
OUT4 enable
0 = disabled
Power
Management
7
OUT3EN
0
6
LOUT2EN
0
LOUT2 enable
0 = disabled
5
ROUT2EN
0
ROUT2 enable
0 = disabled
1 = enabled
Power
Management
0
Reserved
Analogue
Outputs
1 = enabled
OUT3 enable
0 = disabled
Power
Management
1 = enabled
Power
Management
1 = enabled
4
3
RMIXEN
0
Right output channel mixer enable:
0 = disabled
1 = enabled
Analogue
Outputs
2
LMIXEN
0
Left output channel mixer enable:
0 = disabled
1 = enabled
Analogue
Outputs
1
DACENR
0
Right channel DAC enable
Analogue
Outputs
0 = DAC disabled
1 = DAC enabled
0
DACENL
0
Left channel DAC enable
0 = DAC disabled
1 = DAC enabled
4 (04h)
8
BCP
0
BCLK polarity
0=normal
1=inverted
7
LRP
0
LRC clock polarity
0=normal
6:5
WL
10
Word length
00=16 bits
Analogue
Outputs
Digital Audio
Interfaces
Digital Audio
Interfaces
1=inverted
Digital Audio
Interfaces
01=20 bits
10=24 bits
11=32 bits
w
PD, Rev 4.3, May 2010
99
WM8983
REGISTER
ADDRESS
Production Data
BIT
4:3
LABEL
FMT
DEFAULT
10
DESCRIPTION
REFER TO
Digital Audio
Interfaces
Audio interface Data Format Select:
00=Right Justified
01=Left Justified
10=I2S format
11= DSP/PCM mode
2
DLRSWAP
0
Controls whether DAC data appears in ‘right’ or
‘left’ phases of LRC clock:
0=DAC data appear in ‘left’ phase of LRC
Digital Audio
Interfaces
1=DAC data appears in ‘right’ phase of LRC
1
ALRSWAP
0
Controls whether ADC data appears in ‘right’ or
‘left’ phases of LRC clock:
Digital Audio
Interfaces
0=ADC data appear in ‘left’ phase of LRC
1=ADC data appears in ‘right’ phase of LRC
0
5 (05h)
MONO
8:6
0
Selects between stereo and mono device
operation:
0=Stereo device operation
1=Mono device operation. Data appears in ‘left’
phase of LRC
Digital Audio
Interfaces
000
Reserved
5
WL8
0
Companding Control 8-bit mode
0=off
1=device operates in 8-bit mode
Digital Audio
Interfaces
4:3
DAC_COMP
00
DAC companding
00=off (linear mode)
01=reserved
Digital Audio
Interfaces
10=μ-law
11=A-law
2:1
ADC_COMP
00
Digital Audio
Interfaces
ADC companding
00=off (linear mode)
01=reserved
10=μ-law
11=A-law
6 (06h)
0
LOOPBACK
0
Digital loopback function
0=No loopback
1=Loopback enabled, ADC data output is fed
directly into DAC data input.
Digital Audio
Interfaces
8
CLKSEL
1
Controls the source of the clock for all internal
operation:
0=MCLK
Digital Audio
Interfaces
7:5
MCLKDIV
010
1=PLL output
Sets the scaling for either the MCLK or PLL
clock output (under control of CLKSEL)
Digital Audio
Interfaces
000=divide by 1
001=divide by 1.5
010=divide by 2
011=divide by 3
100=divide by 4
101=divide by 6
110=divide by 8
111=divide by 12
w
PD, Rev 4.3, May 2010
100
WM8983
Production Data
REGISTER
ADDRESS
BIT
4:2
LABEL
BCLKDIV
DEFAULT
000
DESCRIPTION
REFER TO
Configures the BCLK output frequency, for use
Digital Audio
when the chip is master over BCLK.
000=divide by 1 (BCLK=MCLK)
001=divide by 2 (BCLK=MCLK/2)
Interfaces
010=divide by 4
011=divide by 8
100=divide by 16
101=divide by 32
110=reserved
111=reserved
1
0
0
MS
0
Reserved
Sets the chip to be master over LRC and BCLK
0=BCLK and LRC clock are inputs
1=BCLK and LRC clock are outputs generated
by the WM8978 (MASTER)
7 (07h)
3:1
SR
000
Approximate sample rate (configures the
coefficients for the internal digital filters):
Digital Audio
Interfaces
Audio Sample
Rates
000=48kHz
001=32kHz
010=24kHz
011=16kHz
100=12kHz
101=8kHz
110-111=reserved
0
SLOWCLKEN
0
Slow clock enable. Used for both the jack insert
detect debounce circuit and the zero cross
timeout.
Analogue
Outputs
0 = slow clock disabled
1 = slow clock enabled
8 (08h)
5:4
OPCLKDIV
00
General
Purpose
Input/Output
(GPIO)
PLL Output clock division ratio
00=divide by 1
01=divide by 2
10=divide by 3
11=divide by 4
3
2:0
GPIO1POL
GPIO1SEL
[2:0]
0
000
0=Non inverted
1=Inverted
General
Purpose
Input/Output
(GPIO)
CSB/GPIO1 pin function select:
000= input (CSB/jack detection: depending on
MODE setting)
General
Purpose
Input/Output
(GPIO)
GPIO1 Polarity invert
001= reserved
010=Temp ok
011=Amute active
100=PLL clk o/p
101=PLL lock
110=logic 0
111=logic 1
w
PD, Rev 4.3, May 2010
101
WM8983
REGISTER
ADDRESS
9 (09h)
Production Data
BIT
LABEL
8:7
DEFAULT
DESCRIPTION
REFER TO
00
Reserved
Jack Detection Enable
0=disabled
1=enabled
Output
Switching
(Jack Detect)
Pin selected as jack detection input
Output
Switching
(Jack Detect)
6
JD_EN
0
5:4
JD_SEL
00
00 = GPIO1
01 = GPIO2
10 = GPIO3
11 = Reserved
3:0
10 (0Ah)
8:7
6
SOFTMUTE
0
Reserved
00
Reserved
0
Softmute enable:
0=Disabled
Output
Switching
(Jack Detect)
Output Signal
Path
1=Enabled
5:4
00
Reserved
Power
Management
3
DACOSR128
0
DAC oversample rate select
0 = 64x (lowest power)
2
AMUTE
0
Automute enable
0 = Amute disabled
1
DACPOLR
0
0
DACPOLL
0
Left DAC output polarity:
0 = non-inverted
1 = inverted (180 degrees phase shift)
Output Signal
Path
8
DACVU
N/A
DAC left and DAC right volume do not update
until a 1 is written to DACVU (in reg 11 or 12)
Digital to
Analogue
Converter
(DAC)
7:0
DACVOLL
11111111
Left DAC Digital Volume Control
Digital to
Analogue
Converter
(DAC)
1 = 128x (best SNR)
Output Signal
Path
1 = Amute enabled
Output Signal
Path
Right DAC output polarity:
0 = non-inverted
1 = inverted (180 degrees phase shift)
11 (0Bh)
0000 0000 = Digital Mute
0000 0001 = -127dB
0000 0010 = -126.5dB
... 0.5dB steps up to
1111 1111 = 0dB
12 (0Ch)
8
DACVU
N/A
DAC left and DAC right volume do not update
until a 1 is written to DACVU (in reg 11 or 12)
Output Signal
Path
7:0
DACVOLR
11111111
Right DAC Digital Volume Control
0000 0000 = Digital Mute
Output Signal
Path
0000 0001 = -127dB
0000 0010 = -126.5dB
... 0.5dB steps up to
1111 1111 = 0dB
w
PD, Rev 4.3, May 2010
102
WM8983
Production Data
REGISTER
ADDRESS
13 (0Dh)
BIT
LABEL
8
7:4
JD_EN1
DEFAULT
DESCRIPTION
REFER TO
0
Reserved
0000
Output enabled when selected jack detection
input is logic 1
[4]= OUT1_EN_1
[5]= OUT2_EN_1
[6]= OUT3_EN_1
Output
Switching
(Jack Detect)
[7]= OUT4_EN_1
3:0
14 (0Eh)
JD_EN0
0000
Output enabled when selected jack detection
input is logic 0.
[0]= OUT1_EN_0
[1]= OUT2_EN_0
[2]= OUT3_EN_0
[3]= OUT4_EN_0
High Pass Filter Enable
0=disabled
1=enabled
Analogue to
Digital
Converter
(ADC)
8
HPFEN
1
7
HPFAPP
0
Select audio mode or application mode
0=Audio mode (1st order, fc = ~3.7Hz)
1=Application mode (2nd order, fc = HPFCUT)
Analogue to
Digital
Converter
(ADC)
6:4
HPFCUT
000
Application mode cut-off frequency
Analogue to
Digital
Converter
(ADC)
See table 14 for details
3
ADCOSR
128
2
1
ADCRPOL
0
ADC oversample rate select
0 = 64x (lowest power)
1 = 128x (best SNR)
0
Reserved
0
ADC right channel polarity adjust:
0=normal
Power
Management
Analogue to
Digital
Converter
(ADC)
1=inverted
0
ADCLPOL
0
Analogue to
Digital
Converter
(ADC)
ADC left channel polarity adjust:
0=normal
1=inverted
15 (0Fh)
8
ADCVU
N/A
ADC left and ADC right volume do not update
until a 1 is written to ADCVU (in reg 16 or 17)
Analogue to
Digital
Converter
(ADC)
7:0
ADCVOLL
11111111
Left ADC Digital Volume Control
0000 0000 = Digital Mute
0000 0001 = -127dB
Analogue to
Digital
Converter
(ADC)
0000 0010 = -126.5dB
... 0.5dB steps up to
1111 1111 = 0dB
16 (10h)
Output
Switching
(Jack Detect)
8
ADCVU
N/A
ADC left and ADC right volume do not update
until a 1 is written to ADCVU (in reg 16 or 17)
Analogue to
Digital
Converter
(ADC)
7:0
ADCVOLR
11111111
Right ADC Digital Volume Control
0000 0000 = Digital Mute
Analogue to
Digital
Converter
(ADC)
0000 0001 = -127dB
0000 0010 = -126.5dB
... 0.5dB steps up to
1111 1111 = 0dB
w
PD, Rev 4.3, May 2010
103
WM8983
REGISTER
ADDRESS
18 (12h)
Production Data
BIT
8
LABEL
EQ3DMODE
7
19 (13h)
DEFAULT
DESCRIPTION
1
0 = Equaliser and 3D Enhancement applied to
ADC path
1 = Equaliser and 3D Enhancement applied to
DAC path
0
Reserved
6:5
EQ1C
4:0
EQ1G
01100
8
EQ2BW
0
20 (14h)
Output Signal
Path
EQ Band 1 Gain Control. See Table 38 for
details.
Output Signal
Path
EQ Band 2 Bandwidth Control
Output Signal
Path
0
Reserved
Output Signal
Path
6:5
EQ2C
01
EQ Band 2 Centre Frequency:
00=230Hz
01=300Hz
10=385Hz
11=500Hz
Output Signal
Path
4:0
EQ2G
01100
EQ Band 2 Gain Control. See Table 38 for
details.
Output Signal
Path
8
EQ3BW
0
EQ Band 3 Bandwidth Control
Output Signal
Path
0=narrow bandwidth
1=wide bandwidth
7
21 (15h)
Output Signal
Path
EQ Band 1 Cut-off Frequency:
00=80Hz
01=105Hz
10=135Hz
11=175Hz
0=narrow bandwidth
1=wide bandwidth
7
REFER TO
0
Reserved
Output Signal
Path
6:5
EQ3C
01
EQ Band 3 Centre Frequency:
00=650Hz
01=850Hz
10=1.1kHz
11=1.4kHz
Output Signal
Path
4:0
EQ3G
01100
EQ Band 3 Gain Control. See Table 38 for
details.
Output Signal
Path
8
EQ4BW
0
EQ Band 4 Bandwidth Control
0=narrow bandwidth
Output Signal
Path
1=wide bandwidth
7
22 (16h)
0
Reserved
Output Signal
Path
6:5
EQ4C
01
EQ Band 4 Centre Frequency:
00=1.8kHz
01=2.4kHz
10=3.2kHz
11=4.1kHz
Output Signal
Path
4:0
EQ4G
01100
EQ Band 4 Gain Control. See Table 38 for
details.
Output Signal
Path
0
Reserved
Output Signal
Path
8:7
6:5
EQ5C
01
EQ Band 5 Cut-off Frequency:
00=5.3kHz
01=6.9kHz
10=9kHz
11=11.7kHz
Output Signal
Path
4:0
EQ5G
01100
EQ Band 5 Gain Control. See Table 38 for
details.
Output Signal
Path
w
PD, Rev 4.3, May 2010
104
WM8983
Production Data
REGISTER
ADDRESS
24 (18h)
25 (19h)
27 (1Bh)
BIT
LABEL
DEFAULT
DESCRIPTION
REFER TO
Enable the DAC digital limiter:
0=disabled
1=enabled
DAC Limiter Decay time (per 6dB gain change)
for 44.1kHz sampling. Note that these will scale
with sample rate:
0000=750us
0001=1.5ms
0010=3ms
0011=6ms
0100=12ms
0101=24ms
0110=48ms
0111=96ms
1000=192ms
1001=384ms
1010=768ms
Output Signal
Path
Output Signal
Path
8
LIMEN
0
7:4
LIMDCY
0011
3:0
LIMATK
0010
DAC Limiter Attack time (per 6dB gain change)
for 44.1kHz sampling. Note that these will scale
with sample rate.
0000=94us
0001=188s
0010=375us
0011=750us
0100=1.5ms
0101=3ms
0110=6ms
0111=12ms
1000=24ms
1001=48ms
1010=96ms
1011 to 1111=192ms
00
6:4
LIMLVL
000
3:0
LIMBOOST
0000
Reserved
Programmable signal threshold level
(determines level at which the DAC limiter starts
to operate)
000=-1dB
001=-2dB
010=-3dB
011=-4dB
100=-5dB
101 to 111=-6dB
DAC Limiter volume boost (can be used as a
stand alone volume boost when LIMEN=0):
0000=0dB
0001=+1dB
0010=+2dB
… (1dB steps)
1011=+11dB
1100=+12dB
1101 to 1111=reserved
8
NFU
0
Notch filter update. The notch filter values used
internally only update when one of the NFU bits
is set high.
Analogue to
Digital
Converter
(ADC)
7
NFEN
0
Notch filter enable:
0=Disabled
1=Enabled
Analogue to
Digital
Converter
(ADC)
6:0
NFA0[13:7]
0000000
Notch Filter a0 coefficient, bits [13:7]
Analogue to
Digital
Converter
(ADC)
8:7
w
Output Signal
Path
Output Signal
Path
Output Signal
Path
PD, Rev 4.3, May 2010
105
WM8983
REGISTER
ADDRESS
28 (1Ch)
Production Data
BIT
8
LABEL
NFU
7
29 (1Dh)
REFER TO
0
Notch filter update. The notch filter values used
internally only update when one of the NFU bits
is set high.
Analogue to
Digital
Converter
(ADC)
0
Reserved
NFA0[6:0]
0000000
Notch Filter a0 coefficient, bits [6:0]
Analogue to
Digital
Converter
(ADC)
8
NFU
0
Notch filter update. The notch filter values used
internally only update when one of the NFU bits
is set high.
Analogue to
Digital
Converter
(ADC)
0
Reserved
6:0
NFA1[13:7]
0000000
Notch Filter a1 coefficient, bits [13:7]
Analogue to
Digital
Converter
(ADC)
8
NFU
0
Notch filter update. The notch filter values used
internally only update when one of the NFU bits
is set high.
Analogue to
Digital
Converter
(ADC)
7
32 (20h)
DESCRIPTION
6:0
7
30 (1Eh)
DEFAULT
0
Reserved
6:0
NFA1[6:0]
0000000
Notch Filter a1 coefficient, bits [6:0]
Analogue to
Digital
Converter
(ADC)
8:7
ALCSEL
00
ALC function select:
Input Limiter/
Automatic
Level Control
(ALC)
00=ALC off
01=ALC right only
10=ALC left only
11=ALC both on
6
5:3
ALCMAXGAIN
0
Reserved
111
Set Maximum Gain of PGA
111=+35.25dB
110=+29.25dB
101=+23.25dB
100=+17.25dB
Input Limiter/
Automatic
Level Control
(ALC)
011=+11.25dB
010=+5.25dB
001=-0.75dB
000=-6.75dB
2:0
ALCMINGAIN
000
Set minimum gain of PGA
000=-12dB
001=-6dB
010=0dB
011=+6dB
Input Limiter/
Automatic
Level Control
(ALC)
100=+12dB
101=+18dB
110=+24dB
111=+30dB
33 (21h)
7:4
ALCHLD
0000
ALC hold time before gain is increased.
0000 = 0ms
0001 = 2.67ms
0010 = 5.33ms
… (time doubles with every step)
1111 = 43.691s
w
Input Limiter/
Automatic
Level Control
(ALC)
PD, Rev 4.3, May 2010
106
WM8983
Production Data
REGISTER
ADDRESS
34 (22h)
BIT
LABEL
DEFAULT
3:0
ALCLVL
1011
8
ALCMODE
0
DESCRIPTION
REFER TO
ALC target – sets signal level at ADC input
1111 : -1.5dBFS
1110 : -1.5dBFS
1101 : -3dBFS
1100 : -4.5dBFS
...... (-1.5dB steps)
0001 : -21dBFS
0000 : -22.5dBFS
Input Limiter/
Automatic
Level Control
(ALC)
Determines the ALC mode of operation:
Input Limiter/
Automatic
Level Control
(ALC)
0=ALC mode
1=Limiter mode
7:4
ALCDCY
[3:0]
0011
Decay (gain ramp-up) time
(ALCMODE ==0)
Per step
Per 6dB
90% of range
0000
410us
3.3ms
24ms
0001
820us
6.6ms
48ms
0010
1.64ms
13.1ms
192ms
Input Limiter/
Automatic
Level Control
(ALC)
… (time doubles with every step)
1010
or
higher
0011
420ms
3.36s
24.576s
Decay (gain ramp-up) time
(ALCMODE ==1)
Per step
Per 6dB
90% of range
0000
90.8us
726.4us
5.26ms
0001
181.6us
1.453ms
10.53ms
0010
363.2us
2.905ms
21.06ms
… (time doubles with every step)
1010
3:0
ALCATK
0010
93ms
744ms
5.39s
ALC attack (gain ramp-down) time
(ALCMODE == 0)
0000
Per step
Per 6dB
90% of range
104us
832us
6ms
0001
208us
1.664ms
12ms
0010
416us
3.328ms
24.1ms
Input Limiter/
Automatic
Level Control
(ALC)
… (time doubles with every step)
1010
or
higher
0010
106ms
852ms
6.18s
ALC attack (gain ramp-down) time
(ALCMODE == 1)
Per step
Per 6dB
90% of range
0000
22.7us
182.4us
1.31ms
0001
45.4us
363.2us
2.62ms
0010
90.8us
726.4us
5.26ms
… (time doubles with every step)
1010
35 (23h)
8:4
3
NGEN
w
23.2ms
186ms
00000
Reserved
0
ALC Noise gate function enable
1 = enable
0 = disable
1.348s
Input Limiter/
Automatic
Level Control
(ALC)
PD, Rev 4.3, May 2010
107
WM8983
REGISTER
ADDRESS
Production Data
BIT
2:0
LABEL
NGTH
DEFAULT
000
DESCRIPTION
REFER TO
Input Limiter/
Automatic
Level Control
(ALC)
ALC Noise gate threshold:
000=-39dB
001=-45dB
010=-51db
… (6dB steps)
111=-81dB
36 (24h)
8:5
4
0000
PLL
0
PRESCALE
Reserved
Master Clock
and Phase
Locked Loop
(PLL)
0 = MCLK input not divided (default)
1 = Divide MCLK by 2 before input to PLL
PLLN[3:0]
1000
Integer (N) part of PLL input/output frequency
ratio. Use values greater than 5 and less than
13.
000
Reserved
5:0
PLLK[23:18]
01100
Fractional (K) part of PLL1 input/output
frequency ratio (treat as one 24-digit binary
number).
Master Clock
and Phase
Locked Loop
(PLL)
38 (26h)
8:0
PLLK[17:9]
010010011
Fractional (K) part of PLL1 input/output
frequency ratio (treat as one 24-digit binary
number).
Master Clock
and Phase
Locked Loop
(PLL)
39 (27h)
8:0
PLLK[8:0]
011101001
Fractional (K) part of PLL1 input/output
frequency ratio (treat as one 24-digit binary
number).
Master Clock
and Phase
Locked Loop
(PLL)
41 (29h)
8:4
00000
Reserved
0000
Stereo depth
0000: 0% (minimum 3D effect)
0001: 6.67%
3:0
37 (25h)
8:6
3:0
DEPTH3D
Master Clock
and Phase
Locked Loop
(PLL)
3D Stereo
Enhancement
....
1110: 93.3%
1111: 100% (maximum 3D effect)
42 (2Ah)
8:6
OUT4_2ADCVOL
000
Controls the OUT4 to ADC input boost stage:
000 = Path disabled (disconnected)
001 = -12dB gain
010 = -9dB gain
Analogue
Outputs
011 = -6dB gain
100 = -3dB gain
101 = +0dB gain
110 = +3dB gain
111 = +6dB gain
5
OUT4_2LNR
0
Analogue
Outputs
OUT4 to L or R ADC input
0 = Right ADC input
1 = Left ADC input
43 (2Bh)
8
BYPL2RMIX
0
Left bypass path (from the Left channel input
PGA stage) to right output mixer
Analogue
Outputs
0 = not selected
1 = selected
7
BYPR2LMIX
6
w
0
Right bypass path (from the right channel input
PGA stage) to Left output mixer
0 = not selected
1 = selected
Analogue
Outputs
0
Reserved
Analogue
Outputs
PD, Rev 4.3, May 2010
108
WM8983
Production Data
REGISTER
ADDRESS
BIT
LABEL
DEFAULT
DESCRIPTION
REFER TO
5
MUTERPGA2INV
0
Mute input to INVROUT2 mixer
Analogue
Outputs
4
INVROUT2
0
Mute input to INVROUT2 mixer
Analogue
Outputs
3:1
BEEPVOL
000
AUXR input to ROUT2 inverter gain
Analogue
Outputs
000 = -15dB
...
111 = +6dB
0
44 (2Ch)
8
BEEPEN
MBVSEL
0
0
1 = enable AUXR beep input
Analogue
Outputs
Microphone Bias Voltage Control
0 = 0.9 * AVDD
Input Signal
Path
0 = mute AUXR beep input
1 = 0.65 * AVDD
7
0
Reserved
6
R2_2INPPGA
0
Connect R2 pin to right channel input PGA
positive terminal.
0=R2 not connected to input PGA
1=R2 connected to input PGA amplifier positive
terminal (constant input impedance).
Input Signal
Path
5
RIN2INPPGA
1
Connect RIN pin to right channel input PGA
negative terminal.
Input Signal
Path
0=RIN not connected to input PGA
1=RIN connected to right channel input PGA
amplifier negative terminal.
4
RIP2INPPGA
1
Input Signal
Path
Connect RIP pin to right channel input PGA
amplifier positive terminal.
0 = RIP not connected to input PGA
1 = right channel input PGA amplifier positive
terminal connected to RIP (constant input
impedance)
3
2
L2_2INPPGA
0
Reserved
0
Connect L2 pin to left channel input PGA
positive terminal.
Input Signal
Path
0=L2 not connected to input PGA
1=L2 connected to input PGA amplifier positive
terminal (constant input impedance).
1
LIN2INPPGA
1
Connect LIN pin to left channel input PGA
negative terminal.
0=LIN not connected to input PGA
1=LIN connected to input PGA amplifier negative
terminal.
Input Signal
Path
0
LIP2INPPGA
1
Connect LIP pin to left channel input PGA
amplifier positive terminal.
Input Signal
Path
0 = LIP not connected to input PGA
1 = input PGA amplifier positive terminal
connected to LIP (constant input impedance)
45 (2Dh)
8
INPPGAU
N/A
INPPGAVOLL and INPPGAVOLR volume do not
update until a 1 is written to INPPGAUPDATE (in
reg 45 or 46)
Input Signal
Path
7
INPPGAZCL
0
Left channel input PGA zero cross enable:
0=Update gain when gain register changes
1=Update gain on 1st zero cross after gain
register write.
Input Signal
Path
6
INPPGAMUTEL
0
Mute control for left channel input PGA:
Input Signal
Path
0=Input PGA not muted, normal operation
1=Input PGA muted (and disconnected from the
following input BOOST stage).
w
PD, Rev 4.3, May 2010
109
WM8983
REGISTER
ADDRESS
Production Data
BIT
5:0
LABEL
INPPGAVOLL
DEFAULT
010000
DESCRIPTION
REFER TO
Input Signal
Path
Left channel input PGA volume
000000 = -12dB
000001 = -11.25db
.
010000 = 0dB
.
111111 = 35.25dB
46 (2Eh)
8
INPPGAU
N/A
INPPGAVOLL and INPPGAVOLR volume do not
update until a 1 is written to INPPGAUPDATE (in
reg 45 or 46)
Input Signal
Path
7
INPPGAZCR
0
Right channel input PGA zero cross enable:
Input Signal
Path
0=Update gain when gain register changes
1=Update gain on 1st zero cross after gain
register write.
6
INPPGAMUTER
0
Mute control for right channel input PGA:
0=Input PGA not muted, normal operation
1=Input PGA muted (and disconnected from the
following input BOOST stage).
Input Signal
Path
5:0
INPPGAVOLR
010000
Right channel input PGA volume
000000 = -12dB
000001 = -11.25db
Input Signal
Path
.
010000 = 0dB
.
111111 = +35.25dB
47 (2Fh)
8
PGABOOSTL
7
6:4
L2_2BOOSTVOL
1
Boost enable for left channel input PGA:
0 = PGA output has +0dB gain through input
BOOST stage.
1 = PGA output has +20dB gain through input
BOOST stage.
0
Reserved
000
Controls the L2 pin to the left channel input
boost stage:
Input Signal
Path
Input Signal
Path
000=Path disabled (disconnected)
001=-12dB gain through boost stage
010=-9dB gain through boost stage
…
111=+6dB gain through boost stage
3
2:0
AUXL2BOOSTVOL
0
Reserved
000
Controls the auxilliary amplifer to the left channel
input boost stage:
Input Signal
Path
000=Path disabled (disconnected)
001=-12dB gain through boost stage
010=-9dB gain through boost stage
…
111=+6dB gain through boost stage
48 (30h)
8
PGABOOSTR
7
w
1
Boost enable for right channel input PGA:
0 = PGA output has +0dB gain through input
BOOST stage.
1 = PGA output has +20dB gain through input
BOOST stage.
0
Reserved
Input Signal
Path
PD, Rev 4.3, May 2010
110
WM8983
Production Data
REGISTER
ADDRESS
BIT
6:4
LABEL
R2_2BOOSTVOL
DEFAULT
000
DESCRIPTION
REFER TO
Input Signal
Path
Controls the R2 pin to the right channel input
boost stage:
000=Path disabled (disconnected)
001=-12dB gain through boost stage
010=-9dB gain through boost stage
…
111=+6dB gain through boost stage
3
2:0
AUXR2BOOSTVOL
0
Reserved
000
Controls the auxilliary amplifer to the right
channel input boost stage:
000=Path disabled (disconnected)
Input Signal
Path
001=-12dB gain through boost stage
010=-9dB gain through boost stage
…
111=+6dB gain through boost stage
49 (31h)
8:7
00
Reserved
6
DACL2RMIX
0
Left DAC output to right output mixer
0 = not selected
5
DACR2LMIX
0
Right DAC output to left output mixer
0 = not selected
3
OUT3BOOST
0
Analogue
Outputs
1 = selected
Analogue
Outputs
1 = selected
Analogue
Outputs
Output 3 Gain
0 = OUT3 output gain = -1;
DC = AVDD1 / 2
1 = OUT3 output gain = +1.5
DC = 1.5 x AVDD1 / 2
4
OUT4BOOST
0
Analogue
Outputs
Output 4 Gain
0 = OUT4 output gain = -1;
DC = AVDD1 / 2
1 = OUT4 output gain = +1.5
DC = 1.5 x AVDD1 / 2
2
SPKBOOST
0
Analogue
Outputs
Speaker Gain
0 = speaker gain = -1;
DC = AVDD1 / 2
1 = speaker gain = +1.5;
DC = 1.5 x AVDD1 / 2
1
TSDEN
1
Analogue
Outputs
Thermal Shutdown Enable
0 : thermal shutdown disabled
1 : thermal shutdown enabled
0
VROI
0
VREF (AVDD/2 or 1.5xAVDD/2) to analogue
output resistance
Analogue
Outputs
0: approx 1kΩ
1: approx 30 kΩ
50 (32h)
8:6
AUXLMIXVOL
000
Aux left channel input to left mixer volume
control:
Analogue
Outputs
000 = -15dB
001 = -12dB
…
101 = 0dB
110 = +3dB
111 = +6dB
5
AUXL2LMIX
0
Left Auxilliary input to left channel output mixer:
0 = not selected
Analogue
Outputs
1 = selected
w
PD, Rev 4.3, May 2010
111
WM8983
REGISTER
ADDRESS
Production Data
BIT
4:2
LABEL
BYPLMIXVOL
DEFAULT
000
DESCRIPTION
REFER TO
Left bypass volume control to output channel
mixer:
Analogue
Outputs
000 = -15dB
001 = -12dB
…
101 = 0dB
110 = +3dB
111 = +6dB
1
BYPL2L
0
MIX
Left bypass path (from the left channel input
boost output) to left output mixer
0 = not selected
Analogue
Outputs
1 = selected
0
DACL2L
MIX
1
8:6
AUXRMIXVOL
000
Analogue
Outputs
Left DAC output to left output mixer
0 = not selected
1 = selected
51 (33h)
Aux right channel input to right mixer volume
control:
Analogue
Outputs
000 = -15dB
001 = -12dB
…
101 = 0dB
110 = +3dB
111 = +6dB
5
AUXR2RMIX
0
Right Auxilliary input to right channel output
mixer:
0 = not selected
1 = selected
Analogue
Outputs
4:2
BYPRMIXVOL
000
Right bypass volume contol to output channel
mixer:
Analogue
Outputs
000 = -15dB
001 = -12dB
…
101 = 0dB
110 = +3dB
111 = +6dB
1
BYPR2RMIX
0
Right bypass path (from the right channel input
boost output) to right output mixer
Analogue
Outputs
0 = not selected
1 = selected
Analogue
Outputs
0
DACR2RMIX
1
Right DAC output to right output mixer
0 = not selected
8
OUT1VU
N/A
LOUT1 and ROUT1 volumes do not update until
a 1 is written to OUT1VU (in reg 52 or 53)
Analogue
Outputs
7
LOUT1ZC
0
Headphone volume zero cross enable:
1 = Change gain on zero cross only
Analogue
Outputs
6
LOUT1MUTE
0
Left headphone output mute:
0 = Normal operation
1 = selected
52 (34h)
0 = Change gain immediately
Analogue
Outputs
1 = Mute
w
PD, Rev 4.3, May 2010
112
WM8983
Production Data
REGISTER
ADDRESS
BIT
5:0
LABEL
LOUT1VOL
DEFAULT
111001
DESCRIPTION
REFER TO
Analogue
Outputs
Left headphone output volume:
000000 = -57dB
...
111001 = 0dB
...
111111 = +6dB
53 (35h)
8
OUT1VU
N/A
LOUT1 and ROUT1 volumes do not update until
a 1 is written to OUT1VU (in reg 52 or 53)
Analogue
Outputs
7
ROUT1ZC
0
Headphone volume zero cross enable:
1 = Change gain on zero cross only
Analogue
Outputs
6
ROUT1MUTE
0
Right headphone output mute:
0 = Normal operation
5:0
ROUT1VOL
111001
0 = Change gain immediately
Analogue
Outputs
1 = Mute
Analogue
Outputs
Right headphone output volume:
000000 = -57dB
...
111001 = 0dB
...
111111 = +6dB
54 (36h)
8
OUT2VU
N/A
LOUT2 and ROUT2 volumes do not update until
a 1 is written to OUT2VU (in reg 54 or 55)
Analogue
Outputs
7
LOUT2ZC
0
Speaker volume zero cross enable:
1 = Change gain on zero cross only
0 = Change gain immediately
Analogue
Outputs
6
LOUT2MUTE
0
Left speaker output mute:
0 = Normal operation
1 = Mute
Analogue
Outputs
5:0
LOUT2VOL
111001
Left speaker output volume:
000000 = -57dB
...
Analogue
Outputs
111001 = 0dB
...
111111 = +6dB
55 (37h)
8
OUT2VU
N/A
LOUT2 and ROUT2 volumes do not update until
a 1 is written to OUT2VU (in reg 54 or 55)
Analogue
Outputs
7
ROUT2ZC
0
Speaker volume zero cross enable:
Analogue
Outputs
1 = Change gain on zero cross only
0 = Change gain immediately
6
ROUT2MUTE
0
Analogue
Outputs
Right speaker output mute:
0 = Normal operation
1 = Mute
5:0
ROUT2VOL
111001
Analogue
Outputs
Right speaker output volume:
000000 = -57dB
...
111001 = 0dB
...
111111 = +6dB
56 (38h)
8:7
6
OUT3MUTE
5:4
w
00
Reserved
0
0 = Output stage outputs OUT3 mixer
1 = Output stage muted – drives out VMID. Can
be used as VMID buffer in this mode.
00
Reserved
Analogue
Outputs
PD, Rev 4.3, May 2010
113
WM8983
REGISTER
ADDRESS
Production Data
BIT
3
LABEL
OUT4_2OUT3
DEFAULT
0
DESCRIPTION
REFER TO
Analogue
Outputs
OUT4 mixer output to OUT3
0 = disabled
1= enabled
2
BYPL2OUT3
0
1
LMIX2OUT3
0
0
LDAC2OUT3
1
Left DAC output to OUT3
0 = disabled
0
Reserved
0
OUT3 mixer output to OUT4
0 = disabled
Analogue
Outputs
Left ADC input to OUT3
0 = disabled
1= enabled
Analogue
Outputs
Left DAC mixer to OUT3
0 = disabled
1= enabled
Analogue
Outputs
1= enabled
57 (39h)
8
7
OUT3_2OUT4
Analogue
Outputs
1 = enabled
6
OUT4MUTE
0
5
OUT4ATTN
0
0 = Output stage outputs OUT4 mixer
1 = Output stage muted – drives out VMID. Can
be used as VMID buffer in this mode.
Analogue
Outputs
0 = OUT4 normal output
Analogue
Outputs
1 = OUT4 attenuated by 6dB
4
LMIX2OUT4
0
Left DAC mixer to OUT4
0 = disabled
1= enabled
Analogue
Outputs
3
LDAC2OUT4
0
Left DAC to OUT4
0 = disabled
1= enabled
Analogue
Outputs
2
BYPR2OUT4
0
Right ADC input to OUT4
0 = disabled
1= enabled
Analogue
Outputs
1
RMIX2OUT4
0
Right DAC mixer to OUT4
Analogue
Outputs
0 = disabled
1= enabled
0
RDAC2OUT4
1
Right DAC output to OUT4
0 = disabled
1= enabled
59 (3Bh)
8:2
1:0
0000000
ALCTST
00
Reserved
ALC Test Mode
00 = disabled
11 = enabled
61 (3Dh)
8
BIASCUT
0
Analogue
Outputs
Global bias control
ALC Test
Mode
Bias Control
0 = normal
1 = 0.5x
7:0
w
00000000
Reserved
PD, Rev 4.3, May 2010
114
WM8983
Production Data
DIGITAL FILTER CHARACTERISTICS
PARAMETER
TEST CONDITIONS
MIN
+/- 0.025dB
0
TYP
MAX
UNIT
ADC Filter
Passband
-6dB
0.454fs
0.5fs
Passband Ripple
+/- 0.025
Stopband
Stopband Attenuation
dB
0.546fs
f > 0.546fs
-60
Group Delay
dB
21/fs
ADC High Pass Filter
High Pass Filter Corner
Frequency
-3dB
3.7
-0.5dB
10.4
-0.1dB
21.6
Hz
DAC Filter
Passband
+/- 0.035dB
0
-6dB
0.454fs
0.5fs
Passband Ripple
+/-0.035
Stopband
Stopband Attenuation
Group Delay
dB
0.546fs
f > 0.546fs
-55
dB
29/fs
Table 71 Digital Filter Characteristics
TERMINOLOGY
1.
Stop Band Attenuation (dB) – the degree to which the frequency spectrum is attenuated (outside audio band)
2.
Pass-band Ripple – any variation of the frequency response in the pass-band region
w
PD, Rev 4.3, May 2010
115
WM8983
Production Data
DAC FILTER RESPONSES
3.05
0
3
-20
2.95
-40
Response (dB)
Response (dB)
20
-60
-80
-100
2.9
2.85
2.8
2.75
-120
2.7
-140
2.65
2.6
-160
0
0.5
1
1.5
2
0
2.5
0.05
0.1
0.15
Figure 54 DAC Digital Filter Frequency Response
(128xOSR)
0.25
0.3
0.35
0.4
0.45
0.5
0.45
0.5
Figure 55 DAC Digital Filter Ripple (128xOSR)
3.05
20
0
3
-20
2.95
-40
Response (dB)
Response (dB)
0.2
Frequency (fs)
Frequency (fs)
-60
-80
-100
2.9
2.85
2.8
2.75
-120
2.7
-140
2.65
2.6
-160
0
0.5
1
1.5
2
0
2.5
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
Frequency (fs)
Frequency (fs)
Figure 56 DAC Digital Filter Frequency Response (64xOSR)
Figure 57 DAC Digital Filter Ripple (64xOSR)
ADC FILTER RESPONSES
0.2
0
0.15
0.1
Response (dB)
Response (dB)
-20
-40
-60
-80
0.05
0
-0.05
-0.1
-100
-0.15
-0.2
-120
0
0.5
1
1.5
2
Frequency (Fs)
Figure 58 ADC Digital Filter Frequency Response
w
2.5
3
0
0.1
0.2
0.3
0.4
0.5
Frequency (Fs)
Figure 59 ADC Digital Filter Ripple
PD, Rev 4.3, May 2010
116
WM8983
Production Data
HIGHPASS FILTER
The WM8983 has a selectable digital highpass filter in the ADC filter path. This filter has two modes,
audio and applications. In audio mode the filter is a 1st order IIR with a cut-off of around 3.7Hz. In
applications mode the filter is a 2nd order high pass filter with a selectable cut-off frequency.
5
0
-5
Response (dB)
-10
-15
-20
-25
-30
-35
-40
0
5
10
15
20
25
30
35
40
45
Frequency (Hz)
Figure 60 ADC Highpass Filter Response, HPFAPP=0
10
10
0
0
-10
-20
Response (dB)
Response (dB)
-10
-20
-30
-30
-40
-50
-40
-60
-50
-70
-80
-60
0
200
400
600
800
1000
1200
0
200
400
600
800
1000
1200
Frequency (Hz)
Frequency (Hz)
Figure 61 ADC Highpass Filter Responses (48kHz),
Figure 62 ADC Highpass Filter Responses (24kHz),
HPFAPP=1, all cut-off settings shown.
HPFAPP=1, all cut-off settings shown.
10
0
-10
Response (dB)
-20
-30
-40
-50
-60
-70
-80
-90
0
200
400
600
800
1000
1200
Frequency (Hz)
Figure 63 ADC Highpass Filter Responses (12kHz),
HPFAPP=1, all cut-off settings shown.
w
PD, Rev 4.3, May 2010
117
WM8983
Production Data
5-BAND EQUALISER
15
15
10
10
5
5
Magnitude (dB)
Magnitude (dB)
The WM8983 has a 5-band equaliser which can be applied to either the ADC path or the DAC path.
The plots from Figure 64 to Figure 77 show the frequency responses of each filter with a sampling
frequency of 48kHz, firstly showing the different cut-off/centre frequencies with a gain of ±12dB, and
secondly a sweep of the gain from -12dB to +12dB for the lowest cut-off/centre frequency of each
filter.
0
-5
-5
-10
-10
-15
-1
10
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
-15
-1
10
5
Figure 64 EQ Band 1 Low Frequency Shelf Filter Cut-offs
15
15
10
10
5
5
0
-5
-10
-10
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
5
Figure 66 EQ Band 2 – Peak Filter Centre Frequencies,
EQ2BW=0
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
5
0
-5
-15
-1
10
10
Figure 65 EQ Band 1 Gains for Lowest Cut-off Frequency
Magnitude (dB)
Magnitude (dB)
0
-15
-1
10
Figure 67
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
5
EQ Band 2 – Peak Filter Gains for Lowest
Cut-off Frequency, EQ2BW=0
15
10
Magnitude (dB)
5
0
-5
-10
-15
-2
10
10
-1
10
0
1
10
Frequency (Hz)
10
2
10
3
10
4
Figure 68 EQ Band 2 – EQ2BW=0, EQ2BW=1
w
PD, Rev 4.3, May 2010
118
WM8983
15
15
10
10
5
5
Magnitude (dB)
Magnitude (dB)
Production Data
0
0
-5
-5
-10
-10
-15
-1
10
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
5
Figure 69 EQ Band 3 – Peak Filter Centre Frequencies,
EQ3BW=0
-15
-1
10
Figure 70
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
5
EQ Band 3 – Peak Filter Gains for Lowest
Cut-off Frequency, EQ3BW=0
15
10
Magnitude (dB)
5
0
-5
-10
-15
-2
10
10
-1
10
0
1
10
Frequency (Hz)
10
2
10
3
10
4
Figure 71 EQ Band 3 – EQ3BW=0, EQ3BW=1
w
PD, Rev 4.3, May 2010
119
Production Data
15
15
10
10
5
5
Magnitude (dB)
Magnitude (dB)
WM8983
0
0
-5
-5
-10
-10
-15
-1
10
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
-15
-1
10
5
Figure 72 EQ Band 4 – Peak Filter Centre Frequencies,
EQ3BW=0
Figure 73
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
5
EQ Band 4 – Peak Filter Gains for Lowest
Cut-off Frequency, EQ4BW=0
15
10
Magnitude (dB)
5
0
-5
-10
-15
-2
10
10
-1
10
0
1
10
Frequency (Hz)
10
2
10
3
10
4
15
15
10
10
5
5
Magnitude (dB)
Magnitude (dB)
Figure 74 EQ Band 4 – EQ3BW=0, EQ3BW=1
0
0
-5
-5
-10
-10
-15
-1
10
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
5
Figure 75 EQ Band 5 High Frequency Shelf Filter Cut-offs
w
-15
-1
10
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
5
Figure 76 EQ Band 5 Gains for Lowest Cut-off Frequency
PD, Rev 4.3, May 2010
120
WM8983
Production Data
Figure 77 shows the result of having the gain set on more than one channel simultaneously. The
blue traces show each band (lowest cut-off/centre frequency) with ±12dB gain. The red traces show
the cumulative effect of all bands with +12dB gain and all bands -12dB gain, with EqxBW=0 for the
peak filters.
20
15
Magnitude (dB)
10
5
0
-5
-10
-15
-1
10
10
0
10
1
2
10
Frequency (Hz)
10
3
10
4
10
5
Figure 77 Cumulative Frequency Boost/Cut
w
PD, Rev 4.3, May 2010
121
WM8983
Production Data
APPLICATIONS INFORMATION
RECOMMENDED EXTERNAL COMPONENTS
Figure 78 External Component Diagram
w
PD, Rev 4.3, May 2010
122
WM8983
Production Data
PACKAGE DIAGRAM
FL: 32 PIN QFN PLASTIC PACKAGE 5 X 5 X 0.9 mm BODY, 0.50 mm LEAD PITCH
DM044.B
D
DETAIL 1
D2
32
25
L
1
24
4
EXPOSED
GROUND 6
PADDLE
A
INDEX AREA
(D/2 X E/2)
E2
17
E
8
16
2X
15
9
b
B
e
1
bbb M C A B
2X
aaa C
aaa C
TOP VIEW
BOTTOM VIEW
ccc C
A3
A
0.08 C
C
SEATING PLANE
5
DETAIL 2
A3
R = 0.3MM x 45o
A1
SIDE VIEW
EXPOSED
GROUND
PADDLE
DETAIL 1
G
b
Exposed lead
DETAIL 2
3.05
Dimensions (mm)
NOM
MAX
NOTE
0.85
0.90
0.02
0.05
0.203 REF
0.30
0.25
1
5.00 BSC
3.10
3.15
2
5.00 BSC
3.10
3.15
2
0.35
0.50 BSC
0.625
0.40
Symbols
A
A1
A3
b
D
D2
E
E2
e
G
L
aaa
bbb
ccc
REF:
MIN
0.80
0
0.20
3.05
0.45
Tolerances of Form and Position
0.15
0.10
0.10
JEDEC, MO-220, VARIATION VHHD-5.
NOTES:
1. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.15 mm AND 0.30 mm FROM TERMINAL TIP.
2. FALLS WITHIN JEDEC, MO-220, VARIATION VHHD-5.
3. ALL DIMENSIONS ARE IN MILLIMETRES.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JEDEC 95-1 SPP-002.
5. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
6. REFER TO APPLICATION NOTE WAN_0118 FOR FURTHER INFORMATION REGARDING PCB FOOTPRINTS AND QFN PACKAGE SOLDERING.
7. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE.
w
PD, Rev 4.3, May 2010
123
WM8983
Production Data
IMPORTANT NOTICE
Wolfson Microelectronics plc (“Wolfson”) products and services are sold subject to Wolfson’s terms and conditions of sale,
delivery and payment supplied at the time of order acknowledgement.
Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the
right to make changes to its products and specifications or to discontinue any product or service without notice. Customers
should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current.
Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty.
Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation.
In order to minimise risks associated with customer applications, the customer must use adequate design and operating
safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer
product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for
such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product.
Wolfson’s products are not intended for use in life support systems, appliances, nuclear systems or systems where
malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage.
Any use of products by the customer for such purposes is at the customer’s own risk.
Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other
intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or
services might be or are used. Any provision or publication of any third party’s products or services does not constitute
Wolfson’s approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document
belong to the respective third party owner.
Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is
accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is
not liable for any unauthorised alteration of such information or for any reliance placed thereon.
Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in
this datasheet or in Wolfson’s standard terms and conditions of sale, delivery and payment are made, given and/or
accepted at that person’s own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any
reliance placed thereon by any person.
ADDRESS:
Wolfson Microelectronics plc
Westfield House
26 Westfield Road
Edinburgh
EH11 2QB
United Kingdom
Tel :: +44 (0)131 272 7000
Fax :: +44 (0)131 272 7001
Email :: [email protected]
w
PD, Rev 4.3, May 2010
124