ACDC 400 Watts SDL Series xppower.com • Single & Dual Outputs • Up to 700 W Peak Power • Fan Fail & Power Good Signals • Variable Speed Fan • Low Leakage Current Option • Fits 1U Applications • 3 Year Warranty Specification Input General 90-264 VAC 47-63 Hz 6 A at 90 VAC, 2.5 A at 230 VAC Max 70 A at 230 VAC, 35 A at 115 VAC, cold start Power Factor • EN61000-3-2 class A, >0.9 Earth Leakage Current • <1.5 mA at 264 VAC, option ‘-L’ 500 µA at 240 VAC Input Protection • T8 A/250 V fuse Input Voltage Input Frequency Input Current Inrush Current • • • • Output • See tables • ±5% on V1 (V2 of dual output models will track by same % of adjustment) Initial Set Accuracy • ±1% Minimum Load • 1% on single output models, 10% on both output of dual output models in order to maintain ripple & noise and regulation specifications Start Up Delay • 1.5 s max at 115 VAC Start Up Rise Time • 50 ms typical Hold Up Time • 16 ms min at 75% of full load at 115 VAC Line Regulation • ±0.5% Load Regulation • ±1% for single outputs, ±3% V1, ±7% V2 for dual outputs (except PD0512 version: ±5% on V1 and ±10% on V2) Over/Undershoot • 5% max Transient Response • ±5% max deviation, recovery to within 1% in 500 µs for a 50% load change Ripple & Noise • 1% pk-pk (see note 3) Overvoltage Protection • <130% on V1 recycle AC input to reset Overload Protection • 110-140% Short Circuit Protection • Trip & restart, auto recovery Fan Supply • <5V at 300mA with 1% load rising to 1213 V at 300mA with full load. Not available on ‘-F’ & ‘-E’ versions with built-in fans Remote On / Off • Applying short circuit between inhibit pin and signal return turns output off. Output Voltage Output Voltage Trim Efficiency Isolation Switching Frequency Power Density Signals MTBF • Single output: 88% typical Dual Output: 85% typical at 230 V & full load • 3000 VAC Input to Output, 1500 VAC Input to Ground, 250 VDC Output to Ground • PFC, 68 kHz PFC, PWM: 55 kHz for single output, & PD1224, 48 kHz for other parts. • 11.11 W/In3 • Fan Fail & Power Good • >100 kHrs to MIL-HDBK-217F, at 25 °C GB Environmental Operating Temperature • 0 °C to +70 °C, derate at 2.5%/°C from +50 °C to +70 °C Storage Temperature • -20 °C to +85 °C Operating Humidity • 5-90%, non-condensing Cooling • ‘-F’ & ‘-E’ versions have built-in variable speed fans, all other models require 15 CFM Operating Altitude • 3000 m Vibration • 5-50 Hz, acceleration 7.35 ms2 on 3 axes EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals • EN55022 Level B conducted & radiated • EN61000-3-2 class A EN61000-3-2 class C for loads ≥30% • EN61000-3-3 • EN61000-4-2, level 3 Perf Criteria A • EN61000-4-3, 3 V/m Perf Criteria A • EN61000-4-4, level 2 Perf Criteria A • EN61000-4-5, installation class 3 Perf Criteria A • EN61000-4-6, 3V Perf Criteria A • EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms Perf Criteria A, B, B • UL60950-1, CSA C22.2 No. 60950-1, EN60950-1 Output Power Forced Air Convection Cooled Cooled 400 W 220 W 400 W 220 W 400 W 220 W 400 W 220 W 400 W 220 W 400 W 220 W 400 W 220 W 400 W 220 W 400 W 220 W 320 W 180 W 320 W 180 W 320 W 180 W 400 W 200 W Voltage 12 15 18 24 28 36 48 54 60 +5 +5 +5 +12 V V V V V V V V V V V V V Output 1 Current Forced Air Convection 33.33 A 18.33 A 26.67 A 14.67 A 22.22 A 12.22 A 16.67 A 9.17 A 14.29 A 7.86 A 11.11 A 6.11 A 8.33 A 4.58 A 7.41 A 4.07 A 6.67 A 3.67 A 30.00 A 15.00 A 30.00 A 15.00 A 30.00 A 15.00 A 20.83 A 12.50 A Output 2 Current Forced Air Convection Voltage Peak(1) 58.33 A 46.77 A 38.89 A 29.17 A 25.00 A 19.44 A 14.58 A 12.96 A 11.61 A 36.00 A 36.00 A 36.00 A 20.00 A +12 +24 +48 +24 V V V V 20.83 10.42 5.21 10.42 A A A A 13.33 6.67 3.33 8.33 A A A A Model Number Peak(1) 20.00 10.00 5.00 10.00 A A A A SDL400PS12 SDL400PS15(4) SDL400PS18(4) SDL400PS24 SDL400PS28(4) SDL400PS36 SDL400PS48 SDL400PS54(4) SDL400PS60(4) SDL400PD0512(4) SDL400PD0524(4) SDL400PD0548(4) SDL400PD1224 Notes 1. Peak load can be taken for 500 µs. Average power not to exceed nominal power. 2. Add suffix ‘-L’ to model number for optional 500 µA leakage current(4) 3. Ripple & noise is measured using 0.1 µF ceramic capacitor in parallel with 22 µF electrolytic and 20 MHz bandwidth. 4. Available for OEM quantities, contact Sales. Mechanical Options • • • • If no suffix is added to the model number the unit is a U-channel, convection-cooled ratings apply or external fan cooling required (15 CFM). Add suffix ‘-E’ to the model number for an end fan cover (forced air cooled ratings apply). Add suffix ‘-F’ to the model number for a top fan cover (forced air cooled ratings apply). Add suffix ‘-C’ to the model number for a U-channel with vented cover. Convection cooled ratings apply or external fan cooling required (15 CFM). • Add suffix ‘D’ to the model number for MOLEX connector for OEM quantities, contact Sales. Mechanical Details Enclosed with End Fan (‘ E’ Option) PIN 1 PG RTN FF INH 12.70 (0.50) A FAN1 + - 25.40 (1.00) PIN 13 PIN 7 PIN 12 PIN 6 76.20 (3.00) PIN 10 PIN 9 PIN 8 PIN 7 PIN 6 PIN 5 PIN 4 PIN 3 PIN 2 PIN 1 PIN 4 PIN 3 PIN 2 PIN 1 PG RTN FF INH A A: Mounting hole 6 Places M4 x 0.7 PIN 11 PIN 5 CN1 FAN1 + - 12.70 (0.50) Option D Molex mating part No. 09-91-1600 (16 PINS) (PINS 11,13 & 15 NOT USED) 177.80 (7.01) TERMINAL BLOCK 7PINS 9.5mm CENTER Pin A 25.40 (1.00) A 101.60 (4.00) 25.40 (1.00) Signal Connector mating part is JST XHP-4 Crimp terminals SXH-002T-P0.6 All dimensions are in inches (mm) Weight: 800 g (1.76 lbs) Tolerance: ±0.012 in (±0.3 mm) 40.64 (1.60) CN2 A A CN1 101.60 (4.00) 101.60 (4.00) Max screw terminal torque: 15.7 lbs-in (1.8 Nm) Max screw mount hole penetration : 0.16 (4.0) 1 2 3 4 5 6 7 8 9 10 11 12 13 PIN CONNECTIONS Standard Molex (Option D) Single Dual Single Dual Vout Vout1 Vout Vout1 Vout Rtn Vout Vout1 Rtn Rtn Vout Vout1 Rtn Vout2 Vout Rtn Ground Ground Vout Rtn Neutral Neutral Rtn Rtn Live Live Rtn Rtn Rtn Rtn Rtn Vout2 Rtn Vout2 Ground Ground Neutral Neutral Live Live ACDC SDL400 Models and Ratings Enclosed with Top Fan (‘ F’ Option) p g 54.39 (2.14) 39.30 (1.55) 54.45±0.30 (2.15±0.012) CN2 A PIN 13 PIN 7 PIN 12 PIN 6 PIN 11 76.20 (3.00) PIN 5 PIN 10 PIN 9 PIN 8 PIN 7 PIN 6 PIN 5 PIN 4 PIN 3 PIN 2 PIN 1 PIN 4 PIN 3 PIN 2 PIN 1 CN1 PG RTN FF INH A A FAN1 + - Option D Molex mating part No. 09-91-1600 (16 PINS) (PINS 11,13 & 15 NOT USED) TERMINAL BLOCK 7PINS 9.5mm CENTER PIN 152.40±0.30 (6.00±0.012) A A 1 2 3 4 5 6 7 8 9 10 11 12 13 25.40 (1.00) 39.30 (1.55) Pin 101.60 (4.00) 25.40 (1.00) Signal Connector mating part is JST XHP-4 Crimp terminals SXH-002T-P0.6 All dimensions are in inches (mm) Weight: 770 g (1.70 lbs) Tolerance: ±0.012 in (±0.3 mm) A: Mounting hole 6 Places M4 x 0.7 25.40 (1.00) A 12.70 (0.50) FAN1 + - CN1 101.60±0.30 (4.00±0.012) 12.70 (0.50) 101.60 (4.00) PG RTN FF INH 38.10 (1.50) PIN 1 Max screw terminal torque: 15.7 lbs-in (1.8 Nm) Max screw mount hole penetration : 0.16 (4.0) CONNECTIONS Standard Molex (Option D) Single Dual Single Dual Vout Vout1 Vout Vout1 Vout Rtn Vout Vout1 Rtn Rtn Vout Vout1 Rtn Vout2 Vout Rtn Ground Ground Vout Rtn Neutral Neutral Rtn Rtn Live Live Rtn Rtn Rtn Rtn Rtn Vout2 Rtn Vout2 Ground Ground Neutral Neutral Live Live UChannel PIN 1 38.10 (1.50) PG RTN FF INH FAN1 + - 25.40 (1.00) 12.70 (0.50) A 38.10 (1.50) CN2 A PIN 7 PIN 13 PIN 6 PIN 12 PIN 11 PIN 5 PIN 10 PIN 9 PIN 8 PIN 7 PIN 6 PIN 5 PIN 4 PIN 3 PIN 2 PIN 1 PIN 4 PIN 3 PIN 2 PIN 1 PG RTN FF INH A A A: Mounting hole 6 Places M4 x 0.7 CN1 101.60 (4.00) 101.60 (4.00) 76.20 (3.00) CN1 FAN1 + - 12.70 (0.50) Option D Molex mating part No. 09-91-1600 (16 PINS) (PINS 11,13 & 15 NOT USED) 152.40 (6.00) TERMINAL BLOCK 7PINS 9.5mm CENTER A A 25.40 (1.00) ACDC SDL400 Mechanical Details 101.60 (4.00) 25.40 (1.00) Signal Connector mating part is JST XHP-4 Fan Connector mating part is JST XHP-2, Crimp terminals SXH-002T-P0.6 All dimensions are in inches (mm) Weight: 680 g (1.50 lbs) Tolerance: ±0.012 in (±0.3 mm) Max screw terminal torque: 15.7 lbs-in (1.8 Nm) Max screw mount hole penetration : 0.16 (4.0) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 PIN CONNECTIONS Standard Molex (Option D) Single Dual Single Dual Vout Vout1 Vout Vout1 Vout Rtn Vout Vout1 Rtn Rtn Vout Vout1 Rtn Vout2 Vout Rtn Ground Ground Vout Rtn Neutral Neutral Rtn Rtn Live Live Rtn Rtn Rtn Rtn Rtn Vout2 Rtn Vout2 Ground Ground Neutral Neutral Live Live UChannel with cover (‘ C’ Option) 38.10 (1.50) PIN 1 FAN1 + - 25.40 (1.00) PIN 13 PIN 7 PIN 12 PIN 6 B PIN 11 76.20 (3.00) PIN 5 PIN 10 PIN 9 PIN 8 PIN 7 PIN 6 PIN 5 PIN 4 PIN 3 PIN 2 PIN 1 PIN 4 PIN 3 PIN 2 PIN 1 PG RTN FF INH A 39.90 (1.57) CN2 A A A: Mounting hole 6 Places M4 x 0.7 101.60 (4.00) 12.70 (0.50) A PG RTN FF INH 101.60 (4.00) CN1 CN1 FAN1 + - A 25.40 (1.00) A 101.60 (4.00) 25.40 (1.00) Signal Connector mating part is JST XHP-4 Fan Connector mating part is JST XHP-2, Crimp terminals SXH-002T-P0.6 All dimensions are in inches (mm) Weight: 720 g (1.59 lbs) Tolerance: ±0.012 in (±0.3 mm) Max screw terminal torque: 15.7 lbs-in (1.8 Nm) Max screw mount hole penetration : 0.16 (4.0) 39.90 (1.57) Option D Molex mating part No. 09-91-1600 (16 PINS) (PINS 11,13 & 15 NOT USED) TERMINAL BLOCK 7PINS 9.5mm CENTER 152.40 (6.00) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 PIN CONNECTIONS Standard Molex (Option D) Single Dual Single Dual Vout Vout1 Vout Vout1 Vout Rtn Vout Vout1 Rtn Rtn Vout Vout1 Rtn Vout2 Vout Rtn Ground Ground Vout Rtn Neutral Neutral Rtn Rtn Live Live Rtn Rtn Rtn Rtn Rtn Vout2 Rtn Vout2 Ground Ground Neutral Neutral Live Live Application Notes Power Good Remote On / Off +5 V OUTPUT ON INH 1K CN1 POWER GOOD PG (5V or open) PSU RTN OUTPUT OFF (0V or short) CN1 RTN POWER NOT GOOD Sink current = 6 mA Source current = 1 mA Note: 1. Applying <0.3 V or short between the pins turns the output OFF. 2. Applying >4.5 V or open circuit between the pins turns output ON. Fan Fail FAN FAILED FF Open collector signal, maximum rating 28 VDC/5 mA CN1 RTN FAN OK 07-May-13 ACDC SDL400 Mechanical Details