DATA SHEET SEMICONDUCTOR SF801F~SF807F VOLTAGE RANGE 50 to 600 Volts 8.0 Amperes ITO-220AC Unit:inch(mm) .185(4.8) MAX FEATURES .406(10.3)MAX .130(3.3) MAX .134(3.4)DIA .113(3.0)DIA .112(2.85) .100(2.55) • Low forward voltage drop .272(6.9) .248(6.3) • High current capability • High reliability .606(15.4) .583(14.8) • High surge current capability • Good for switching mode application • High temperature soldering : 260OC / 10 seconds at terminals .161(4.1) MAX • Pb free product at available : 99% Sn above meet RoHS environment substance directive request MECHANICAL DATA .114(2.9) .098(2.5) .055(1.4) MAX .032(0.8) MAX .035(0.9) MAX .543(13.8) .512(13.0) • Case: Molded plastic .100(2.55) .100(2.55) • Epoxy: UL 94V-0 rate flame retardant • Lead: Lead solderable per MIL-STD-202, method 208 guranteed • Polarity: As Marked • Mounting position: Any • Weight: 2.24 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25°C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. SF801F SF802F SF803F SF804F SF805F SF806F SF807F Maximum Recurre nt Peak Reverse V oltage TYPE NUMBER 50 100 150 200 300 400 600 V Maximum RMS Voltage 35 70 105 140 210 320 420 V Maximum DC Blo cking Voltage 50 100 150 200 300 400 600 V Maximum Average Forward Rect if ied Current .375"(9.5mm) Lead Length at Tc=100 °C Peak For ward Surge Current , 8.3 ms single half s ine-wave super imposed on rated load (J EDEC method) Maximum I nstantaneous Forward Vol tage at 8.0A 8.0 A 125 A 0.95 Maxi mum DC Reverse Current Tc=25 °C 1.30 1.70 10 at Rated DC Block ing Vol tage Tc=100 °C 35 Typi cal Junction Capaci tance (Note 2) Operating and Storage Temperature Range TJ, TSTG V µA 500 Maximum Reverse Recovery Time (Note 1) UNITS µA 50 nS 50 pF -55 +150 °C NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. http://www.yeashin.com 1 REV.02 20110725 RATINGS AND CHARACTERISTIC CURVES SF801F~SF807F FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC trr 10Ω NONINDUCTIVE ( ) (+) D.U.T. 25Vdc (approx.) PULSE GENERATOR (NOTE 2) ( ) 1Ω NONINDUCTIVE | | | | | | | | +0.5A 0 -0.25A AVERAGE FORWARD CURRENT,(A) 50Ω NONINDUCTIVE (+) OSCILLISCOPE (NOTE 1) -1.0A NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 1cm 2. Rise Time= 10ns max., Source Impedance= 50 ohms. SET TIME BASE FOR 12 10 8 Single Phase 6 Half Wave 60Hz Resistive Or Inductive Load 4 2 0 0 25 50 75 100 125 150 175 CASE TEMPERATURE,( C) 50 / 10ns / cm FIG.3-TYPICAL FORWARD FIG.4-TYPICAL REVERSE CHARACTERISTICS CHARACTERISTICS 1000 REVERSE LEAKAGE CURRENT, (µA) 10 60 300 V-4 00V V-2 1.0 0V 00V 3.0 100 INSTANTANEOUS FORWARD CURRENT,(A) 50 Tj=25 C Pulse Width 300us 1% Duty Cycle 0.1 .01 .4 .6 .8 1.0 1.2 1.4 1.6 100 10 Tc=25 C 1.0 0.1 1.8 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FORWARD VOLTAGE,(V) FIG.6-TYPICAL JUNCTION CAPACITANCE FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 175 125 JUNCTION CAPACITANCE,(pF) PEAK FORWARD SURGE CURRENT,(A) Tc=100 C 100 75 Tj=25 C 8.3ms Single Half Sine Wave 50 JEDEC method 25 150 125 100 75 50 25 0 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz http://www.yeashin.com .01 .05 .1 .5 1 5 10 REVERSE VOLTAGE (V) 2 REV.02 20110725 50 100