AOSMD AOZ1605

AOZ1605
500 mA / 3 MHz EZBuck Regulator
General Description
Features
The AOZ1605 is a high-performance, easy-to-use Buck
regulator. The 3 MHz switching frequency, low quiescent
current and small package size make it an ideal choice
for portable applications. The AOZ1605 has a patented
light load mode architecture allowing up to 85% efficiency
at 1 mA load currents, enabling longer standby times in
battery operated systems.
 2.5 V to 5.5 V input voltage range
The AOZ1605 operates from a 2.5 V to 5.5 V input
voltage range and provides up to 500 mA of output
current with an output voltage adjustable down to 0.6 V.
 Up to 500 mA continuous output current
 30 A quiescent current
 0.05 A shutdown current
 Output voltage adjustable to 0.6 V
 Fixed output voltages available
 ± 1.5% initial accuracy
 3 MHz constant frequency operation
 Low drop-out operation: 100% duty cycle
 Cycle-by-cycle current-limit
The AOZ1605 is available in a tiny 2 mm x 2 mm 8-pin
DFN package and is rated over a -40 °C to +85 °C
ambient temperature range.
 Thermal overload protection
 Excellent load transient response
 Internal soft-start
 Tiny 2 mm x 2 mm DFN-8 package
Applications
 Smart phones
 Personal media players
 MP3 players
 Digital still cameras
 Wireless modems and LANs
 Portable USB devices
Typical Application
AOZ1605DI
VIN = 2.5V to 5.5V
IN
L1
1.0µH
VOUT = 500mA
LX
C1
10µF
R1
PGND
C2
10µF
FB
R2
Off On
Rev. 1.2 June 2012
EN
AGND
www.aosmd.com
Page 1 of 15
AOZ1605
Ordering Information
Part Number
Output
Voltage
Marking
Temperature
Range
Package
Environmental
AOZ1605DI
Adjustable
0
-40 °C to +85 °C
2 x 2 DFN-8
Green Product
AOS Green Products use reduced levels of Halogens, and are also RoHS compliant.
Please visit www.aosmd.com/media/AOSGreenPolicy.pdf for additional information.
Pin Configuration
PGND
1
8
LX
VIN
2
7
NC
AGND
NC
3
6
EN
AGND
4
5
FB
2mm x 2mm DFN-8 Package
(Top View)
Pin Description
Pin Number
Pin Name
1
PGND
2
VIN
Input Supply Pin
3, 7
NC
No Connect Pin
4
AGND
Analog Ground
5
FB
Feedback Input. Connect an external resistive voltage divider to FB to set the output voltage.
6
EN
Enable Input. The device is enabled when EN is high and disabled when EN is low.
8
LX
Switching Node
Pad
AGND
Analog Ground
Rev. 1.2 June 2012
Pin Function
Power Ground
www.aosmd.com
Page 2 of 15
AOZ1605
Absolute Maximum Ratings
Recommended Operating Conditions
Exceeding the Absolute Maximum Ratings may damage the
device.
The device is not guaranteed to operate beyond the
Maximum Recommended Operating Conditions.
Parameter
Rating
IN, EN, FB to AGND
Parameter
-0.3 V to +6 V
LX to AGND
Supply Voltage (VIN)
2.5 V to 5.5 V
-0.3 V to VIN + 0.3 V
Ambient Temperature (TA)
-40 °C to +85 °C
-0.3 V to +0.3 V
Junction Temperature (TJ)
Internally Limited
PGND to AGND
Junction Temperature (TJ)
+150 °C
Storage Temperature (TS)
-65 °C to +150 °C
Maximum Soldering Temperature (10s)
ESD Rating
Rating
(1)
Package Thermal Resistance
2 x 2 DFN-6 (JA)
55 °C/W
+300 °C
2 kV
Note:
1. Devices are inherently ESD sensitive, handling precautions are
required. Human body model rating: 1.5k in series with 100pF.
Electrical Characteristics
TA = 25 °C, VIN = 3.6 V, EN = IN, unless otherwise specified. Specifications in BOLD indicate a temperature range of
-40 °C to +85 °C.
Symbol
Parameter
Conditions
Min.
VIN
Input Voltage Range
2.5
VUV
Under-Voltage Lockout
2.11
Under-Voltage Lockout Hysteresis
IIN
Input Supply Current
IFB
Feedback Reference Voltage
2.3
5.5
V
2.49
V
mV
30
55
0.05
0.1
0.588
0.600
0.612
TA = -40 C to +85 °C, no load
0.585
0.600
0.615
Feedback Line Regulation
VIN = 2.5 V to 5.5 V
Feedback Load Regulation
0 to 500 mA load
Feedback Bias Current
V
%/V
-0.001
% / mA
0.01
0.1
1.2
VEN = 5.5 V
A
0.3
A
V
Enable Input Low Voltage
Enable Bias current
Units
TA = +25 °C, no load
Enable Input High Voltage
IEN
Max
100
EN = IN, VFB = 1 V, no load
EN = AGND
VFB
Typ.
0.4
V
0.01
0.1
A
3
3.75
MHz
OSCILLATOR
fSW
Switching Frequency
2.25
DMAX
Maximum Duty Cycle
100
T(ON)MIN
Minimum On-Time
%
60
ns
1.2
A
PROTECTION
ILIM+
Positive Current Limit
0.7
Thermal Shutdown Threshold
+145
°C
Thermal Shutdown Hysteresis
40
°C
OUTPUT STAGE
RDS(ON)P
PFET On Resistance
ILX = 50 mA sourcing
400
m
RDS(ON)N
NFET On Resistance
ILX = 50 mA sinking
250
m
LX Leakage Current
VEN = 0 V, VLX = 0 V or VIN, VIN = 5 V
Efficiency
VIN = 3.6 V, VOUT = 1.8 V, 200 mA load
Rev. 1.2 June 2012
www.aosmd.com
1
90
A
%
Page 3 of 15
AOZ1605
Output Voltage Selection for AOZ1605
The output voltage of the AOZ1605 ca be programmed
through the resistor network connected from Vout to
Feedback to Analog Ground. The resistor from FB to
Analog Ground should be 100 k to keep the current
drawn through this network below the 6 A quiencent
current level in PFM mode. The output voltage of the
adjustable AOZ1605 parts ranges from 0.6 V to 3.3 V.
The output voltage formula is:
Table 1. Output Voltage Resistor Selection Table for
Various Vout Voltages
Vout
(V)
R1
(k)
R2
(k)
L
(H)
Cin
(F)
Cout
(F)
C5
(pF)
0.6
0
100
1.0
10
10
100
1.1
83
100
1.0
10
10
100
R1
V OUT = V FB  -------- + 1
 R2

1.2
100
100
1.0
10
10
100
1.3
117
100
1.0
10
10
100
where;
1.5
150
100
1.0
10
10
100
VOUT = Output Voltage (V)
1.6
167
100
1.0
10
10
100
1.7
183
100
1.0
10
10
100
1.8
200
100
1.0
10
10
100
1.875
213
100
1.0
10
10
100
2.5
317
100
1.0
10
10
100
2.8
367
100
1.0
10
10
100
3.3
450
100
1.0
10
10
100
VFB = Feedback Voltage (0.6 V typical)
R1 = Feedback Resistor from Vout to FB ()
R2 = Feedback Resistor from FB to AGND ()
A 100 pF bypass capacitor C5 on the evaluation board,
in parallel with the feedback resistor from Vout to FB is
chosen for increased stability throughout the voltage
range.
Rev. 1.2 June 2012
www.aosmd.com
Page 4 of 15
AOZ1605
Typical Performance Characteristics
Output Voltage vs. Supply Voltage
Output Voltage vs. Temperature
1.812
1.90
Vin = 5.0 V
Vout = 1.8 V
Vout = 1.8 V
Output Voltage (V)
Output Voltage (V)
1.810
1.808
1.806
1.804
1.802
1.85
Iout = 100 mA
1.80
300 mA
500 mA
1.75
Iout = 100 mA, 300 mA, 500 mA
1.800
1.798
3.5
4.0
4.5
5.0
Supply Voltage (V)
5.5
1.70
-25
6.0
-5
15
35
55
Temperature (°C)
75
95
Efficiency vs. Output Current
Output Voltage vs. Output Current
(Vout = 1.5 V, L = 1.0 µH)
1.812
100
Vin = 3.0 V
Efficiency (%)
1.808
1.806
1.804
1.802
90
Vin = 4.5 V
Vin = 3.6 V
80
70
Vin = 3.6 V
1.800
60
1.798
100
200
300
Output Current (mA)
400
500
1
10
100
Output Current (mA)
1000
Efficiency vs. Output Current
Efficiency vs. Output Current
(Vout = 2.5V, L = 1.0µH)
(Vout = 1.8 V, L = 1.0 µH)
100
100
Vin = 3.0 V
Vin = 2.7 V
90
Efficiency (%)
Efficiency (%)
Output Voltage (V)
Vout = 1.8 V
Vin = 5.0 V
1.810
Vin = 4.5 V
80
Vin = 3.6 V
90
Vin = 4.5 V
Vin = 3.6 V
80
70
70
60
60
1
Rev. 1.2 June 2012
10
100
Output Current (mA)
1000
www.aosmd.com
1
10
100
Output Current (mA)
1000
Page 5 of 15
AOZ1605
Typical Performance Characteristics (Continued)
Efficiency vs. Output Current
Switching Frequency vs. Temperature
(Vout = 3.3V, L = 1.0µH)
3.20
100
3.15
Vin = 5.0 V
3.10
90
Frequency (MHz)
Efficiency (%)
Vin = 4.5 V
Vin = 5.0 V
80
70
3.05
Vin = 3.6 V
3.00
2.95
Vin = 4.5 V
2.90
2.85
2.80
60
1
10
100
Output Current (mA)
1000
2.75
-25
-5
15
35
55
Temperature (°C)
Load Transient Response
Load Transient Response
VOUT = 1.8V (PWM Mode)
VOUT = 1.8V (PFM Mode, 0.5mA to 50mA)
VSW
VSW
2V/div
50mV/div
AC Coupled
VOUT
95
75
2V/div
50mV/div
AC Coupled
VOUT
400mA
IOUT
200mA
50mA
IOUT
VIN = 3.6V, VOUT = 1.8V
5mA
VIN = 3.6V, VOUT = 1.8V
100μs/div
100μs/div
Load Transient Response
Mode Change by Load Transients
VOUT = 1.8V (PFM Mode, 0.5mA to 50mA)
VOUT = 1.8V (PFM to PWM Mode)
VSW
2V/div
VOUT
50mV/div
AC Coupled
VSW
2V/div
IL
500mA/div
VOUT
100mV/div
AC Coupled
50mA
IOUT
5mA
VIN = 3.6V, VOUT = 1.8V
VIN = 3.6V, VOUT = 1.8V
100μs/div
Rev. 1.2 June 2012
300mA
IOUT
5mA
100μs/div
www.aosmd.com
Page 6 of 15
AOZ1605
Typical Performance Characteristics (Continued)
Mode Change by Load Transients
Startup into PFM Mode
VOUT = 1.8V (PWM to PFM Mode)
VOUT = 1.8V (Output Current = 5mA)
VSW
2V/div
IL
500mA/div
VOUT
100mV/div
AC Coupled
300mA
IOUT
VSW
2V/div
VOUT
1V/div
EN
2V/div
5mA
100μs/div
100μs/div
Startup into PWM Mode
Steady State PWM Mode
VOUT = 1.8V (Output Current = 500mA)
VOUT = 1.8V (Output Current = 500mA)
VSW
2V/div
VSW
2V/div
VOUT
1V/div
IL
500mA/div
EN
2V/div
VOUT
20mV/div
100μs/div
Rev. 1.2 June 2012
200ns/div
www.aosmd.com
Page 7 of 15
AOZ1605
Block Diagram
VIN
C1
3 MHz
Oscillator
ENABLE
UVLO
Thermal
Shutdown
Output
Logic
Control
+
Isense
Amp
–
L1
LX
VOUT
COUT
PGND
+
Ilimit
Comp
–
+
–
FB
+
Error
Amp
–
PFM
Master
Logic
VREF
600mV
PWM
R1
R2
+
–
Operation
The AOZ1605 has a patented light load mode
architecture allowing up to 85% efficiency at 1 mA load
currents, enabling longer standby times in battery
operated systems.
The AOZ1605 is a high efficiency step down DC-DC buck
converter that operates typically at 3 MHz fixed Pulse
Width Modulation (PWM) at medium to heavy load
currents. The AOZ1605 can deliver a constant voltage
from a single Li-Ion battery with an input voltage rail from
2.5 Volts to 5.5 Volts. Using a voltage mode architecture
with synchronous rectification, the AOZ1605 has the
ability to deliver up 500 mA of continuous current
Rev. 1.2 June 2012
depending on the input voltage, output voltage, ambient
temperature and inductor chosen.
There are two modes of operations depending on the
current consumption, PFM (Pulse Frequency
Modulation) and PWM (Pulse Width Modulation).
For ultra-low current the device operates in the PFM
mode to obtain high efficiency that is characteristic of
the PFM mode. The device operates in the PWM mode
when the output current exceed the load current of
approximately 100 mA or higher.
Additional feature include under voltage lockout,
over current protection, thermal shutdown and soft-start.
www.aosmd.com
Page 8 of 15
AOZ1605
Inductor Selection
There are two main considerations when choosing an
inductor; the inductor should not saturate, and the
inductor current ripple should be small enough to achieve
the desire output voltage ripple. A 1 H inductor with a
saturation current of at least 1 A is recommended for the
AOZ1605 full load application. For maximum efficiency,
the inductor’s resistance (DCR) should be as low as
possible. For given input and output voltage, inductance
and switching frequency together decide the inductor
ripple current, which is,
VO 
VO 
I L = -----------   1 – ---------
V IN
fL 
The input ripple voltage can be approximated by
equation below:
VO  VO
IO

V IN = -----------------   1 – ---------  --------V IN V IN
f  C IN 
Since the input current is discontinuous in a buck
converter, the current stress on the input capacitor is
another concern when selecting the capacitor. For a buck
circuit, the RMS value of input capacitor current can be
calculated by:
VO 
VO 
I CIN_RMS = I O  ---------  1 – ---------
V IN 
V IN
The peak inductor current is:
if we let m equal the conversion ratio:
I L
I Lpeak = I O + -------2
VO
-------- = m
V IN
High inductance gives low inductor ripple current
but requires larger size inductor to avoid saturation.
Low ripple current reduces inductor core losses.
It also reduces RMS current through inductor and
switches, which results in less conduction loss.
Usually, peak to peak ripple current on inductor is
designed to be 20% to 30% of output current.
When selecting the inductor, make sure it is able to
handle the peak current without saturation even at the
highest operating temperature.
The inductor takes the highest current in a buck circuit.
The conduction loss on inductor need to be checked for
thermal and efficiency requirements.
The relationship between the input capacitor RMS
current and voltage conversion ratio is calculated and
shown in Figure 1 below. It can be seen that when VO is
half of VIN, CIN is under the worst current stress. The
worst current stress on CIN is 0.5 x IO.
0.5
0.4
ICIN_RMS(m) 0.3
IO
0.2
0.1
Surface mount inductors in different shape and styles are
available from Coilcraft, Elytone and Murata. Shielded
inductors are small and radiate less EMI noise. But they
cost more than unshielded inductors. The choice
depends on EMI requirement, price and size.
Input Capacitor
The input capacitor must be connected to the VIN pin and
PGND pin of AOZ1605 to maintain steady input voltage
and filter out the pulsing input current. The voltage rating
of input capacitor must be greater than maximum input
voltage plus ripple voltage. For greater capacitor
performance, the working capacitance voltage should be
twice Vin.
Rev. 1.2 June 2012
0
0
0.5
m
1
Figure 3. ICIN vs. Voltage Conversion Ratio
For reliable operation and best performance, the input
capacitors must have current rating higher than ICIN_RMS
at worst operating conditions. Ceramic capacitors are
preferred for input capacitors because of their low ESR
and high current rating. When selecting ceramic
capacitors, X5R or X7R type dielectric ceramic
capacitors should be used for their better temperature
and voltage characteristics. Note that the ripple current
rating from capacitor manufactures are based on certain
amount of life time. Further de-rating may be necessary
in practical design.
www.aosmd.com
Page 9 of 15
AOZ1605
Output Capacitor
The output capacitor is selected based on the DC output
voltage rating, output ripple voltage specification and
ripple current rating.
The selected output capacitor must have a higher rated
voltage specification than the maximum desired output
voltage including ripple. De-rating needs to be
considered for long term reliability.
Output ripple voltage specification is another important
factor for selecting the output capacitor. In a buck
converter circuit, output ripple voltage is determined by
inductor value, switching frequency, output capacitor
value and ESR. It can be calculated by the equation
below:
1
V O = I L   ESR CO + -------------------------

8fC 
O
Usually, the ripple current rating of the output capacitor
is a smaller issue because of the low current stress.
When the buck inductor is selected to be very small
and inductor ripple current is high, output capacitor could
be overstressed.
Thermal Shutdown
In most applications the AOZ1605 does not dissipate
much heat due to its high efficiency. But in an application
where the AOZ1605 is running at high ambient
temperature with low supply voltage and high duty cycle,
the heat dissipated may exceed the maximum junction
temperature. If the junction temperature reaches
approximately 140 °C (typical), the internal High Side
and Low Side MOSFET switching is disabled until the
temperature on the die has sufficiently fallen below
105°C. The device remains in thermal shutdown until the
junction temperature falls below the thermal shutdown
hysteresis.
where,
Undervoltage Lockout
CO is output capacitor value and
The undervoltage lockout circuit prevents the device from
malfunctioning at low input voltages and from excessive
discharge of the battery by disabling the output stage of
the converter. The AOZ1605 will resume normal
operation when the input supply voltage rises high
enough to properly function. The undervoltage lockout
threshold is typically 2.3 Volts.
ESRCO is the Equivalent Series Resistor of output capacitor.
When low ESR ceramic capacitor is used as output
capacitor, the impedance of the capacitor at the switching
frequency dominates. Output ripple is mainly caused by
capacitor value and inductor ripple current. The output
ripple voltage calculation can be simplified to:
Soft Start
1
V O = I L  ------------------------8fC
O
If the impedance of ESR at switching frequency
dominates, the output ripple voltage is mainly decided by
capacitor ESR and inductor ripple current. The output
ripple voltage calculation can be further simplified to:
V O = I L  ESR CO
For lower output ripple voltage across the entire
operating temperature range, X5R or X7R dielectric type
of ceramic, or other low ESR tantalum are recommended
to be used as output capacitors.
In a buck converter, output capacitor current is
continuous. The RMS current of output capacitor is
decided by the peak to peak inductor ripple current. It can
be calculated by:
I L
I CO_RMS = ---------12
Rev. 1.2 June 2012
The AOZ1605 has a soft-start circuit that limits the
inrush current during startup. Soft start is activated when
EN goes from logic low to logic high after Vin reaches 2.3
Volts.
Over Current Protection (OCP)
The sensed inductor current signal is also used for over
current protection. Since the AOZ1605 employs peak
current mode control, the COMP pin voltage is
proportional to the peak inductor current. The COMP pin
voltage is limited to be between 0.4 V and 2.5 V
internally. The peak inductor current is automatically
limited cycle by cycle.
When the output is shorted to ground under fault
conditions, the inductor current decays very slow during
a switching cycle because of VO = 0 V. To prevent
catastrophic failure, a secondary current limit is designed
inside the AOZ1605. The measured inductor current is
compared against a preset voltage which represents the
current limit, approximately 1 A. When the output current
is more than current limit, the high side switch will be
turned off. The converter will initiate a soft start once the
over-current condition disappears.
www.aosmd.com
Page 10 of 15
AOZ1605
Enable
The EN pin of the AOZ1605 is active high. Connect the
EN pin to VIN if enable function is not used. Pull it to
ground will disable the AOZ1605. Do not leave it open.
The voltage on EN pin must be above 2 V to enable
the AOZ1605. When voltage on EN pin falls below 0.6 V,
the AOZ1605 is disabled. If an application circuit requires
the AOZ1605 to be disabled, an open drain or open
collector circuit should be used to interface to EN pin.
Low Drop Out Operation
The AOZ1605 can operate at 100% duty cycle. In this
state, the high side p-channel MOSFET is always on.
This will allow the output to follow the input voltage as it
drops below the regulation voltage.
Thermal Management and Layout
Considerations
In the AOZ1605 buck regulator circuit, high pulsing
current flows through two circuit loops. The first loop
starts from the input capacitors, to the VIN pin, to the
LX pin, to the filter inductor, to the output capacitor and
load, and then return to the input capacitor through
ground. Current flows in the first loop when the high side
switch is on. The second loop starts from inductor, to the
output capacitors and load, to the low side NMOSFET.
Current flows in the second loop when the low side
NMOSFET is on.
In PCB layout, minimizing the two loops area reduces the
noise of this circuit and improves efficiency. A ground
plane is strongly recommended to connect input
capacitor, output capacitor, and PGND pin of the
AOZ1605.
In the AOZ1605 buck regulator circuit, the major power
dissipating components are the AOZ1605 and the output
inductor. The total power dissipation of converter circuit
can be measured by input power minus output power.
P total_loss = V IN  I IN – V O  I O
The power dissipation of inductor can be approximately
calculated by output current and DCR of inductor.
P inductor_loss = IO2  R inductor  1.1
The actual junction temperature can be calculated with
power dissipation in the AOZ1605 and thermal
impedance from junction to ambient.
T junction =  P total_loss – P inductor_loss    JA
The maximum junction temperature of AOZ1605 is
140 ºC, which limits the maximum load current capability.
Please see the thermal de-rating curves for maximum
load current of the AOZ1605 under different ambient
temperature.
The thermal performance of the AOZ1605 is strongly
affected by the PCB layout. Extra care should be taken
by users during design process to ensure that the IC will
operate under the recommended environmental
conditions.
Rev. 1.2 June 2012
www.aosmd.com
Page 11 of 15
AOZ1605
The AOZ1605 is an exposed pad DFN-8 package.
Several layout tips are listed below for the best electric
and thermal performance.
1. The exposed pad is connected to PGND. Connect a
large copper plane to this pad to help thermal
dissipation.
2. Do not use thermal relief connection from the VIN pin
and the PGND pin. Pour a maximized copper area to
the PGND pin and the VIN pin to help thermal
dissipation.
4. A ground plane is preferred. If a ground plane is not
used, separate PGND from AGND and connect them
only at one point to avoid the PGND pin noise
coupling to the AGND pin.
5. Make the current trace from LX pin to L to Co to
PGND as short as possible.
6. Pour copper planes on all unused board area and
connect them to stable DC nodes, like VIN, GND
or VOUT.
7. Keep sensitive signal traces away from the LX pin.
3. Input capacitor should be connected as close as
possible to the VIN pin and the PGND pin. For optimal performance of the device, place bulk capacitor
and de-coupling capacitor no further than 50 mils
from the device.
Figure 2. AOZ1605 (DFN-8) PCB Layout
Rev. 1.2 June 2012
www.aosmd.com
Page 12 of 15
AOZ1605
Package Dimensions, DFN 2x2, 8L
B
D
C A B
bbb
A
8
b
e
8
R
aaa C
2x
E
Pin#1 Identification
Option 1
E1
L
1
D1
1
a a a C 2x
BOTTOM VIEW
TOP VIEW
8
ccc C
A C
C
A1
ddd C
Pin#1 Identification
Option 2
seating
plan
SIDE VIEW
Chamfer 0.2x45°
1
BOTTOM VIEW
RECOMMENDED LAND PATTERN
0.50
Dimensions in millimeters
0.25
0.25
0.85
0.90
1.70
0.30
1.50
UNIT: mm
Symbols
A
A1
b
c
D
D1
E
E1
e
Min.
0.70
0.00
0.18
L
R
aaa
bbb
ccc
ddd
0.20
1.90
1.35
1.90
0.75
Nom.
0.75
0.02
0.25
0.20 REF
2.00
1.50
2.00
0.90
0.50 BSC
Max.
0.80
0.05
0.30
0.30
0.20
0.15
0.10
0.10
0.08
0.40
2.10
1.60
2.10
1.00
Dimensions in inches
Symbols
A
A1
b
c
D
D1
E
E1
e
Min.
0.028
0.000
0.007
Nom. Max.
0.030 0.031
0.001 0.002
0.010 0.012
0.008 REF
0.075 0.079 0.083
0.053 0.059 0.063
0.075 0.079 0.083
0.030 0.035 0.039
0.020 BSC
L
R
aaa
bbb
ccc
ddd
0.008
0.012
0.008
0.006
0.004
0.004
0.003
0.016
Notes:
1. Dimensioning and tolerancing conform to ASME Y14.5M-1994.
2. Controlling dimension is in millimeter, converted inch dimensions are not necessarily exact.
3. Dimension b applies to matellized terminal and is measured between 0.10mm and 0.30mm from the terminal tip.
If the terminal has the optional radius on the other end of the terminal, the dimension b should not be measured
in that radius area.
4. Coplanarity ddd applies to the terminals and all other bottom surface metallization.
Rev. 1.2 June 2012
www.aosmd.com
Page 13 of 15
AOZ1605
Tape and Reel Dimensions, DFN 2x2, 8L
Carrier Tape
SECTION A--A
FEEDING DIRECTION
UNIT: MM
Package
A0
B0
DFN 2x2
2.25
±0.05
2.25
±0.05
D0
K0
D1
E
E1
E2
P0
P1
P2
1.00 1.50 1.00
8.00 1.75
±0.05 ±0.10 ±0.25 ±0.30 ±0.10
-0.10
3.50 4.00
±0.05 ±0.10
4.00 2.00
±0.10 ±0.05
M
N
W1
W2
H
S
K
Ø177.8
MAX.
53.6
MIN.
8.4
+2.5
-0.0
14.4
MAX.
13.0
+0.5
-0.3
1.5
MIN.
10.1
MIN.
T
0.254
±0.02
Reel
UNIT: MM
Tape Size
8mm
Reel Size
Ø177.8
Leader/Trailer and Orientation
Rev. 1.2 June 2012
www.aosmd.com
Page 14 of 15
AOZ1605
Part Marking
AOZ1605DI
(2x2 DFN-8)
Part Number
AG O A
Y W LT
Year Code
Assembly Location
Option Code
Assembly Lot
Week Code
This datasheet contains preliminary data; supplementary data may be published at a later date.
Alpha & Omega Semiconductor reserves the right to make changes at any time without notice.
LIFE SUPPORT POLICY
ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS.
As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant into
the body or (b) support or sustain life, and (c) whose
failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of
the user.
Rev. 1.2 June 2012
2. A critical component in any component of a life
support, device, or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
www.aosmd.com
Page 15 of 15