AOSMD AOZ6115

AOZ6115
High Performance, Low RON,
SPST Analog Switch
General Description
Features
The AOZ6115 is a high performance single-pole
single-throw (SPST), low power, TTL-compatible bus
switch.
●
SOT23 and SC70 5-Lead Package
●
1.65V to 5.5V VCC operation
●
Low CON: 18pF
The AOZ6115 can handle analog and digital signals.
Signals with voltages up to VCC (1.65V to 5.5V) can be
transmitted in either direction.
When the Select pin is HIGH, A is connected to the output
B pin. The path that is open will have a high-impedance
state with respect to the output.
Applications
●
Audio and Video Signal Routing
●
Battery Operated Equipment
●
Communications Circuit
●
Relay Replacement
●
Power Routing
Typical Application
AOZ6115
IC
+
–
Rev. 2.2 February 2010
www.aosmd.com
Power Supply
Page 1 of 11
AOZ6115
Ordering Information
Part Number
Ambient Temperature Range
Package
Environmental
AOZ6115CI
AOZ6115HI
-40°C to +85°C
SOT23 5-Lead
SC70 5-Lead
RoHS Compliant
Green Product
AOS Green Products use reduced levels of Halogens, and are also RoHS compliant.
Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information.
Pin Configuration
Truth Table
Logic S Input
B
1
A
2
GND
3
5
4
VCC
Function
0
No Connection
1
A Connected to B
S
SOT23-5L/SC70-5L
(Top View)
Rev. 2.2 February 2010
www.aosmd.com
Page 2 of 11
AOZ6115
Absolute Maximum Ratings
Exceeding the Absolute Maximum ratings may damage the device.
Symbol
Parameter
VCC
Rating
Supply Voltage
-0.5V to +6V
(1)
Switch Voltage
VSW
-0.5V to VCC
(1)
VIN
Input Voltage
IIK
Minimum Input Diode Current(2)
-50mA
ISW
Switch Current
130mA
Peak Switch Current (Pulsed at 1ms, <10% Duty Cycle)
260mA
ISWPEAK
-0.5V to VCC
Storage Temperature Range
TSTG
-65°C to +150°C
Maximum Junction Temperature
TJ
300mW
Human Body Model (JESD22A-114E)
8000V
SOT23-5 Power Dissipation at 85°C
PD
ESD
+150°C
(3)
Recommend Operating Ratings
The device is not guaranteed to operate beyond the Maximum Operating Ratings.
Symbol
Parameter
Rating
VCC
Supply Voltage
VIN
Control Input Voltage(4)
0V to VCC
VSW
Switch Input Voltage
0V to VCC
TA
1.65V to +5.5V
Operating Temperature
-40°C to +85°C
Notes:
1. The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed.
2. Negative current should not exceed minimum negative value.
3. All leads welded or soldered to PC Board.
4. Unused inputs must be held HIGH or LOW. They may not float.
Rev. 2.2 February 2010
www.aosmd.com
Page 3 of 11
AOZ6115
Electrical Characteristics (Continued)
Unless otherwise indicated, specifications indicate a temperature range of -40°C to +85°C
Symbol
Parameter
Test Conditions
Min.
Typ.(1)
Max.
Units
DC CHARACTERISTICS
VIH
VIL
RON
Input Voltage High
Input Voltage Low
1.5
VCC = 4.5V to 5.5V
2.0
V
VCC = 2.7V to 3.6V
0.6
VCC = 4.5V to 5.5V
0.8
VCC = 2.7V, IOUT = 100mA, B = 1.5V
3.0
4.0
VCC = 4.5V, IOUT = 100mA, B = 3.5V
2.0
3.0
On Resistance
Flatness
VCC = 4.5V, IOUT = 100mA, B = 0V, 1V, 2V
0.8
Input Leakage Current
VIN = 0V or VCC
-1.0
IB(off)
Off Stage Switch Leakage
VCC = 5.5V, A = 1V, 4.5V, B = 4.5V, 1V
-100
IA(on)
On State Switch Leakage
VCC = 5.5V, A = 1V, 4.5V, B = floating
-20
RFLAT
IIN
On Resistance
VCC = 2.7V to 3.6V
V
Ω
Ω
1.0
µA
4
100
nA
1
20
nA
5.5
V
POWER SUPPLY
VCC
Power Supply Range
ICCQ
Quiescent Supply Current
VCC = 5.5V, VIN = 0V or VCC, IOUT = 0V
0.5
1
µA
ICCT
Increase in ICC per Input
VCC = 3.6V, VIN = 2.0V
3.3
10
µA
VCC = 5.5V, VIN = 2.4V
20
30
VCC = 2.7V to 3.6V
20
65
VCC = 4.5V to 5.5V
10
40
VCC = 2.7V to 3.6V
20
30
VCC = 4.5V to 5.5V
10
20
VCC = 2.7V to 3.6V
1
VCC = 4.5V to 5.5V
2
1.65
AC CHARACTERISTICS
tON
tOFF
Q
Turn-On Time
Turn-Off Time
Charge Injection
B = 1.5V, RL = 50Ω,
CL = 35pF
B = 1.5V, RL = 50Ω,
CL = 35pF
CL = 1.0nF, VGE = 0V,
RGEN = 0Ω
ns
ns
pC
ANALOG SWITCH CHARACTERISTICS
Off Isolation
RL = 50Ω, f = 1MHz
-70
dB
BW
-3dB Bandwidth
RL = 50Ω
300
MHz
THD
Total Harmonic
Distortion
VCC = 5V, RL = 600Ω, CL = 50pF,
f = 20Hz to 20kHz
0.005
%
2
pF
OIRR
CAPACITANCE
CIN
Control Pin Capacitance
VCC = 0V, f = 1MHz
COFF
B Port Off Capacitance
VCC = 4.5V, f = 1MHz
7.5
pF
CON
A Port Capacitance When
Switch Enable
VCC = 4.5V, f = 1MHz
18
pF
Note:
1. Typical values:
Rev. 2.2 February 2010
www.aosmd.com
Page 4 of 11
AOZ6115
AC Loading and Waveforms
Vcc
A
B
Control
Input
VOUT
RL
50Ω
t
Vcc
R = t F = 2.5nS
50%
0V
t OFF
CL
35pF
VOUT
Switch
Output
GND
0.9 x VOUT
0.9 x VOUT
0
t ON
Logic input waveform are inverted for switches with opposite
logic sense
CL Includes Fixture and Stray Capacitance
Figure 1. Turn-On/Turn-Off Timing
Vcc
R GEN
V GEN
A
B
Input
Control
VOUT
CL
VOUT
IN
Δ VOUT
OFF
OFF
ON
S
GND
IN
ON
OFF
OFF
Q = (ΔVOUT)(CL)
Figure 2. Charge Injection
Vcc
Vcc
Network Analyzer
Audio Analyzer
50Ω
600 Ω
BN
A
A
Source
Signal
BN
CL
Source
Signal
S
S
+
50Ω
+
GND
600 Ω
GND
CL Includes Fixture and Stray Capacitance
Figure 3. Bandwidth
Rev. 2.2 February 2010
Figure 4. Harmonic Distortion
www.aosmd.com
Page 5 of 11
AOZ6115
AC Loading and Waveforms (Continued)
Network
Analyzer
Vcc
VIN
B
VOUT
50 Ω
A
S
Vcc or 0V
+
50 Ω
Source
Signal
50Ω
GND
Figure 5. Off Isolation
Vcc
10nF
A
S
Capacitance
Meter
f = 1MHz
B
0V
or
Vcc
GND
Figure 6. ON/Off Capacitance Measurement
Rev. 2.2 February 2010
www.aosmd.com
Page 6 of 11
AOZ6115
Package Dimensions, SOT23-5L
Gauge Plane
Seating Plane
D
L2
e1
C
5
L
E E1
θ
1
e
b
A2
A
aaa
A1
RECOMMENDED LAND PATTERN
1.90
2.40
0.80
0.95
UNIT: mm
0.63
Dimensions in millimeters
Dimensions in inches
Symbols
A
A1
A2
Min.
—
0.00
0.70
Nom.
—
—
0.88
Max.
1.00
0.10
0.95
Symbols
A
A1
A2
Min.
—
0.00
0.028
Nom.
—
—
0.035
Max.
0.039
0.004
0.037
b
C
D
E
E1
0.35
0.10
2.80
2.60
1.50
0.40
0.13
2.90
2.80
1.60
0.50
0.20
3.00
3.00
1.70
b
C
D
E
E1
0.014
0.004
0.110
0.102
0.059
0.016
0.005
0.114
0.110
0.063
0.020
0.008
0.118
0.118
0.067
e
e1
L
L2
aaa
0.95 BSC
1.90 BSC
0.30
0.40
0.60
0.25 BSC
0.10
e
e1
L
L2
aaa
0.037 BSC
0.075 BSC
0.012 0.016 0.024
0.010 BSC
0.004
θ
0°
—
8°
θ
0°
—
8°
Notes:
1. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 5 mils.
2. Dimension "L" is measured in gauge plane.
3. Tolerance ±0.10mm (4 mil) unless otherwise specified
4. Refer to JEDEC MO-193C AB.
5. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact.
Rev. 2.2 February 2010
www.aosmd.com
Page 7 of 11
AOZ6115
Tape and Reel Dimensions, SOT23-5L
Tape
P2
P1
D1
D0
E1
K0
E2
E
B0
A0
P0
Feeding Direction
Unit: mm
Package
A0
B0
K0
D0
D1
E
E1
E2
P0
P1
P2
T
SOT23-5/6L
LP
3.15
±0.10
3.20
±0.10
1.40
±0.10
1.50
±0.05
1.00
+0.10 / -0
8.00
±0.30
1.75
±0.10
3.50
±0.05
4.00
±0.10
4.00
±0.10
2.00
±0.05
0.23
±0.03
Reel
W1
S
K
R
M
N
J
H
Unit: mm
Tape Size
Reel Size
M
N
8mm
ø177.8
ø177.8
Max.
55.0
Min.
W1
H
8.4
13.0
+1.50 / -0.0 +0.5 / -0.2
S
K
R
J
1.5
Min
10.1
Min.
12.7
4.0
±0.1
Leader/Trailer and Orientation
Trailer Tape
300mm min.
Rev. 2.2 February 2010
Components Tape
Orientation in Pocket
www.aosmd.com
Leader Tape
500mm min.
Page 8 of 11
AOZ6115
Package Dimensions, SC70-5L
Gauge Plane
L1
D
θ
L
E1
E
θ1
e
R
c
e1
A2
A
.010mm
b
A1
Dimensions in millimeters
RECOMMENDED LAND PATTERN
0.65
0.975
0.65
1.95
0.35
Symbols
A
A1
A2
b
c
D
E
e
e1
E1
Min.
0.90
0.00
0.7
0.15
0.08
L
L1
R
θ
0.26
Nom.
0.95
—
0.9
0.22
0.127
2.10 BSC
2.30 BSC
0.65 BSC
1.30 BSC
1.30 BSC
Max.
1.10
0.10
1.00
0.30
0.20
0.40
0.46
2.54 BSC
0.1
—
—
0
4
8
Dimensions in inches
Symbols
A
A1
A2
b
c
D
E
e
e1
E1
Min.
0.035
0.00
0.028
0.006
0.003
L
L1
R
θ
0.010
Nom. Max.
0.037 0.043
—
0.004
0.035 0.039
0.008 0.012
0.005 0.008
0.083 BSC
0.091 BSC
0.026 BSC
0.051 BSC
0.051 BSC
0.015 0.018
0.01 BSC
0.004
—
—
0
4
8
Notes:
1. All dimensions are in millimeters.
θ1
7 NOM
θ1
7 NOM
2. Dimensions are inclusive of plating
3. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 3 mils each.
4. Die is facing up for mold and facing down for trim/form; i.e., reverse trim/form.
5. Dimension L is measured in gauge plane.
6. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact.
Rev. 2.2 February 2010
www.aosmd.com
Page 9 of 11
AOZ6115
Tape and Reel Dimensions, SC70-5L
Carrier Tape
P1
D1
P2
T
E1
E2
E
B0
K0
A0
D0
P0
Feeding Direction
UNIT: mm
Package
SC-70, 6L
(8mm)
A0
2.40
±0.10
B0
2.40
±0.10
K0
1.19
±0.10
D0
1.00
Min.
D1
1.55
±0.05
E
8.00
±0.30
Reel
E1
1.75
±0.10
E2
3.50
±0.05
P0
4.00
±0.10
P1
4.00
±0.10
P2
2.00
±0.05
T
0.25
±0.05
W1
S
G
N
M
K
V
R
H
W
W
Tape Size Reel Size
M
N
8mm
ø180
ø180.00 ø60.50 9.00
±0.30
±0.50
W1
11.40
±1.00
H
K
ø13.00
10.60
+0.50/-0.20
S
2.00
±0.50
G
ø9.00
R
5.00
V
18.00
Leader/Trailer and Orientation
Trailer Tape
300mm min. or
75 empty pockets
Rev. 2.2 February 2010
Components Tape
Orientation in Pocket
www.aosmd.com
Leader Tape
500mm min. or
125 empty pockets
Page 10 of 11
AOZ6115
Part Marking
A R2D
11
AOZ6115CI
Assembly Lot Code
Week & Year Code
Part Number Code
Assembly Location Code
AOZ6115HI
Assembly Lot Code
C 2D
Part Number Code
Week & Year Code
Assembly Location Code
This datasheet contains preliminary data; supplementary data may be published at a later date.
Alpha & Omega Semiconductor reserves the right to make changes at any time without notice.
LIFE SUPPORT POLICY
ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS.
As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant into
the body or (b) support or sustain life, and (c) whose
failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of
the user.
Rev. 2.2 February 2010
2. A critical component in any component of a life
support, device, or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
www.aosmd.com
Page 11 of 11