Front Back AGGP.25F.07.0060A Specification Part No. AGGP.25F.07.0060A Product Name 25mm Two Stage GPS-Glonass- GNSS Active Patch Antenna Module with Front-end Saw Filter Features Industry leading GPS~GLONASS antenna performance 25.1*25.1*7.4mm (Ground Plane) 60mm Ø1.13 IPEX MHFI (U.FL) 28dB LNA Wide Input Voltage 1.8V to 5.5V Low Power Consumption RoHS Compliant SPE-12-8-015/B/SS | page 1 of 11 1. Introduction The AGGP.25F GPS – Glonass- GNSS active patch antenna (along with the AGGP.35 model) is the best choice to use as an embedded antenna with the latest generation of GPS-Glonass -GNSS receivers. The AGGP.25F aslo includes a two stage LNA and a front-end SAW filter to reduce out of band noise such as from nearby cellular transceiver, and improve probability of the wireless device passing radiated spurious emissions certification. It utliizes a 25.1*25.1*4mm advanced wide-band ceramic patch antenna with optimized gain, radiation patttern and axial ratio at GPS and Glonass centre frequencies. Produced in TS16949 automotive quality approved facility and 100% tested for gain (S21), return loss (S11) to ensure total consistency of performance. Cable type, length and connectors can be customized and samples offered according to requirement, subject to minimum order quantities in production. Taoglas also offers custom tuning service based on minimum order quantities, contact your local regional sales office for details. The AGGP.25F consists of 2 functional blocks – the LNA and also the patch antenna. ANTENNA SAW Filter LNA LNA SPE-12-8-015/B/SS | page 2 of 11 2. Specification 2.1 Patch Antenna Parameter Specification Frequency 1574~1610MHz Gain @ Zenith 1575.42MHz 1.5 dBic Typ. @ Zenith 1602MHz +0 dBic Typ. @ Zenith Polarization RHCP Axial Ratio 3.0dB max @ Zenith Patch Dimension 25.1*25.1*4mm 2.2 LNA Parameter Specification Frequency 1574~1610MHz Outer Band Attenuation 1592±140MHz 15dB min. Output Impedance 50Ω Output VSWR 2.0 Max Pout at 1dB Gain Compression point Typ. -2dBm Min. -6dBm LNA Gain, Power Consumption and Noise Figure Voltage LNA Gain (Typ) Power Consumption (mA) Typ Noise Figure Typ Min. 1.8V 22dB 5mA 2.6dB Typ. 3.0V 28dB 10mA 2.6dB Max. 5.5V 31dB 23mA 2.9dB 2.3 Cable* & Connector Parameter Specification RF Cable Coaxial Cable Ø 1.13 ± 0.1mm, length 60 ± 2.5mm Connector IPEX MHFI (U.FL) SPE-12-8-015/B/SS | page 3 of 11 3. LNA Gain and Out Band Rejection @3.0V Tr1 S21 Log Mag 10.00dB/ Ref 0.000dB [F2 smo] Tr1 S22 SWR 1.000/ Ref 1.000 [F2 smo] 40.00 >2 1.6100000 GHz 27.949 dB 2 30.00 1 20.00 3 10.00 4 0.000 6 1 -10.00 5 -20.00 7 -30.00 -40.00 -50.00 2 -60.00 6 4 1 Center 1.592 GHz Ch1 Ch1 Ch1 Ch1 Ch1 Ch1 Ch1 Ch1 Ch1 Ch1 Ch1 Tr1 Tr1 Tr1 Tr1 Tr1 Tr1 Tr1 Tr2 Tr2 Tr2 Tr2 S21 S21 S21 S21 S21 S21 S21 S22 S22 S22 S22 1 >2 3 4 5 6 7 1 2 3 4 1 3 IFBW 1 kHz 1.5740000 1.6100000 1.5920000 1.5420000 1.6420000 1.4920000 1.6920000 1.5740000 1.6100000 1.5920000 1.5420000 GHz GHz GHz GHz GHz GHz GHz GHz GHz GHz GHz 28.186 27.949 29.044 9.0245 -10.035 4.4105 -14.431 1.0816 1.1855 1.2488 1.3486 2 5 7 Span 400 MHz 5/16 Cor dB dB dB dB dB dB dB SPE-12-8-015/B/SS | page 4 of 11 4. LNA Noise Figure @3.0V Mkr1 1.592 GHz 2.558 dB 30.030 dB 19.00 NFIG Scale/ 2.000 dB 1 -1.000 40.00 1 GAIN Scale/ 5.000 dB -10.00 Center 1.57400 GHz BW 4 MHz Tcold 296.50 K Avgs Off Points 11 Att 0/ - - dB Stop 1.61000 GHz Loss Off Corr 5. Total Specification (through Antenna, LNA, Cable and Connector) Parameter Specification Frequency 1574~1610MHz Gain at 90° 1575.42MHz: 26.5 ± 3dBic 1602MHz: 28 ± 3dBic Output Impedance 50Ω Polarization RHCP Output VSWR Max 2.0 Operation Temperature -40°C to + 85°C Storage Temperature -40°C to + 85°C Relative Humidity 40% to 95% Input Voltage Min. 1.8V, Typ. 3.0V, Max. 5V Antenna 25.1*25.1*7.4mm SPE-12-8-015/B/SS | page 5 of 11 6. Radiation Patterns 6.1 1575.42MHz XZ & YZ Plane 0 2 -5 -10 -15 -20 -25 -30 -35 -40 90 270 -45 180 Pattern Model No. Test Mode Freq (MHz) Max Gain(dBi) Min Gain(dBi) Avg. Gain(dBi) Source Polar. 1 AGGP.25F.07.0060A XZ 1575.42 -1.41 / 343.00 -5.88 / 82.00 -3.32 V+H 2 AGGP.25F.07.0060A YZ 1575.42 -1.09 / 0.00 -5.80 / 99.00 -2.76 V+H SPE-12-8-015/B/SS | page 6 of 11 6.2 1602MHz XZ &YZ Plane 0 5 0 -5 -10 -15 -20 -25 -30 -35 -40 90 270 -45 180 Pattern Model No. Test Mode Freq (MHz) Max Gain(dBi) Min Gain(dBi) Avg. Gain(dBi) Source Polar. 1 AGGP.25F.07.0060A XZ 1602.00 0.28 / 338.00 -12.36 / 99.00 -2.49 V+H 2 AGGP.25F.07.0060A YZ 1602.00 0.19 / 0.00 -2.17 / 260.00 -0.91 V+H SPE-12-8-015/B/SS | page 7 of 11 7. Plugs Usage Precautions 7.I Mating / unmating (1) To disconnect connectors, insert the end portion of I-PEX under the connector flanges and pull off vertically, in the direction of the connector mating axis. Coaxial Cable (2) To mate the connectors, the mating axes of both connectors must be aligned and the connectors can be mated. The “click” will confirm fully mated connection. Do not attempt to insert on an extreme angle. 2 PLUG 1 Pulling Tool P/N : 90192-001 RECEPTACLE 7.2 Pull forces on the cable after connectors are mated After the connectors are mated, do not apply a load to the cable in excess of the values indicated in the diagram below. 2N MAX. PLUG 4N MAX. 2N MAX. RECE Coaxial Cable SPE-12-8-015/B/SS | page 8 of 11 IPEX MHFI B B IPEX MHF 1 C Top C2 Amend Shielding Case Drawing Sandy 2011/12/27 Sandy 2012/01/31 Sandy Kiwi Sandy Sandy Sandy 2011/11/23 2011/9/6 2011/12/27 2011/11/21 2012/01/31 "A" B AGGP.25F Top C Amend Logo Placement AGGP.25F 8. Technical Drawing E3 ALL Initial Design ALL Initial Design E3 Amend Logo Placement E2 Add LOGO C2 Amend Shielding Case Drawing A A IPEX MHFI B Top "A" B Side AP.10E B Side Bottom Side C Bottom C Bottom "A" Finish P/N Name Material NOTE: 1.Soldered area 1 AGGP.25F Patch(25*25*4.2mm) AGGP.25F Ceramic Clear 2.Shielding case area Name P/N Material Finish QTY FEP 2 1.13 Coaxial Cable Gray OD.113.CM 3.All material must be RoHS compliant. 1 AGGP.25F NOTE: Finish Clear Patch (25*25*4.2mm) 1 Finish P/N AGGP.25F Name Material Ceramic QTY Name P/N Material QTY NOTE: NOTE: 4.The connector orientation has a fixed 1.Soldered area 1. Soldered area IPEX MHF1 Connector Gold 1.Soldered area 1 AGGP.25F Patch(25*25*4.2mm) 3 Brass IPEX.MHFI.113 AGGP.25F Ceramic Clear 1 AP.10E Patch(10*10*4mm) AP.10E 1 2 Ceramic FEP Clear 1.13 Coaxial Cable OD.113.CM Gray1 1 positioncase tocase the antenna as per drawing. 2.Shielding case area 2.Shielding area 2. Shielding area 2 1.13 Coaxial Cable OD.113.CM FEP Gray 1 3.All material must bebeRoHS 4 PCB Green FR4 0.8tGold1 material mustbe RoHScompliant. compliant. FEP Coaxial Cable Gray MHF1 Connector OD.081.CM IPEX.MHFI.113 Brass 1 3. All3.All material must RoHS compliant. 2 3 0.81IPEX 4.The 4.Theconnector connectororientation orientationhas hasa afixed fixed IPEX MHF1 Connector Gold 1 3 IPEX.MHFI.113 Brass 4. The connector orientation has a fixed Tin Plated 5 Shielding Case IPEX.MHFI.113 (Tin)SPTE position MHF1 Brass 1 positiontotothe theantenna antennaasasper perdrawing. drawing. 3 4 IPEX PCB FR4Gold 0.8t Green 1 position to the antenna as per drawing. 4 PCB Green 1 FR4 0.8t Tin (SPTE) 4 5 Shielding Case Tin Plated 1 Shielding Case (Tin)SPTE Tin Plated 1 5 5 PCB Shielding Case (Tin)SPTE FR4 0.5t Tin Plated Green 1 1 TW Design Centre This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas. TW Design Centre This drawing and its inherent design concepts are property Taoglas. Not to TW of Design Centre be copied or given to third parties without the written consent of Taoglas. This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas. SPE-12-8-015/B/SS | page 9 of 11 QTY 1 1 1 1 1 8.1 Connector Drawing IPEX MHFI Top A ALL Initial Design B E3 C C2 Amend Logo Placement Amend Shielding Case Drawin "A" B Side Bottom SPE-12-8-015/B/SS | page 10 of 11 5 包裝規格 9. 5.1 每個 tray 放置 60 天線 【60pcs antennas per tray】 Packaging 5.2 每 6 個 tray 包裝成 1 組, 【Stack up 6 trays together】 5.3 每箱放置 3 組 tray,總共 1080pcs 天線 Packaged in plastic tray with foam comparment in tray contains 2 pcs of AGGP.25F 【3 sets per box. i.e.1080pcs antenna Each per box.】 60 pcs of antenna per tray 5.4 包裝時須注意不可壓到天線,裝入需平整不可雜亂 【Antenna should be placed flat and neat, packing without pressing or damage the antenna】 5.5 清點每 tray 數量不可短缺 【Confirm the quantity in each tray】 AGGP.25F AGGP.25F 6 trays together in one section Tray 箱子 3 sections per carton 1080 pcs of antenna per carton Taoglas makes no warranties based on the product descriptions at any time accuracy or completeness of the contents without notice. of this document and reserves the rightTOLERANCES to Taoglas reserves UNLESS OTHER SPECIFIED ON： all rights to this document make changes to specifications and and the information X＝± X.X＝± X.XX＝ ANGLES＝± HOLEDIA＝± SCALE： xxxx UNIT：mm DRAWN BY: jason CHECKED BY: Jimmy DESIGNED BY: Jimmy APPROVED BY: Jimmy contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright © Taoglas Ltd. SPE-12-8-015/B/SS | page 11 of 11