ATC HIGH POWER RESISTIVE Surface Mount Chip Resistors Style CS Top View Style CS1 and Style CW General Specifications • Resistance: 100 Ω standard, (other Ω values available) • Resistive Tolerance: ±2% standard • Temperature Coefficient: <150 ppm/˚C Bottom View L LT • Substrate Material: Aluminum Nitride • Lead-Free, RoHS Compliant T T • Resistive Elements: Proprietary Thin Film • Terminals: Silver over Nickel L WT W • Reliability: MIL-PRF-55342 WT W L T WT LT LA Capacitance ±.010 ±.010 ±.005 ±.005 ±.005 ±.005 (pF) CS12010TxxxxG CS12525TxxxxG CS13725TxxxxG CS13737TxxxxG .100 .245 .250 .370 .200 .245 .375 .370 .040 .040 .040 .040 .090 .120 .120 .360 .030 .040 .050 .050 .095 .110 .195 .195 W LT LA • Tape and Reel Specifications: See Page 39 of the full Resistive Products Catalog ATC Part Number* Style CW Overcoat Side View • Operating Temp Range: -55 to +150˚C PRODUCTS Power Max** (Watts) .95 pF 1.85 pF 3.0 pF 3.5 pF 10W 20W 30W 40W ATC Part Number* W ±.010 L ±.010 T ±.005 WT ±.005 LT ±.005 Power Max** (Watts) CW12010TxxxxG .100 .200 .040 .090 .030 4W CW12525TxxxxG .245 .245 .040 .120 .040 6W CW13725TxxxxG .250 .375 .040 .120 .050 8W CW13737TxxxxG .370 .370 .040 .360 .050 10W * xxxx denotes Ohm value. ** Test Condition: Chip soldered to a via patch on a 30-mil-thick Rogers RO4350 board; Land surfaces at 100° C; maximum rated power applied. Specification: The resistance of the film shall change no more than 0.5% during and after a 1000-hr. Burn-in per Mil-PRF-55342. Power Derating ATC Part Number Code CS1 2010 T xxxx J TR Power Dissipation 100% 80 Case Style 60 Packaging TR - Tape & Reel BK - Plastic Carrier Tolerance See table below. Value Case Size Rated Safe Operating Range 40 Termination 20 Resistive Tolerances 0 -50˚C -25˚C 0˚C +25˚C +50˚C 75˚C 100˚C 125˚C 150˚C Heat Sink Temperature (C) Code G (%) J (%) Tol. ±2 ±5 Sales of ATC products are subject to the terms and conditions contained in American Technical Ceramics Corp. Terms and Conditions of Sale (ATC document #001-992 Rev. B 12/05). Copies of these terms and conditions will be provided upon request. They may also be viewed on ATC's website at www.atceramics.com/productfinder/default.asp. Click on the link for Terms and Conditions of Sale. ATC has made every effort to have this information as accurate as possible. However, no responsibility is assumed by ATC for its use, nor for any infringements of rights of third parties which may result from its use. ATC reserves the right to revise the content or modify its product without prior notice. © 2012 American Technical Ceramics Corp. All Rights Reserved. A M E R I C A N ATC North America [email protected] Excerpt from ATC # 001-944; Rev. R, 11/13 T E C H N I C A L C E R A M I C S ATC Europe [email protected] ATC Asia [email protected] www.at c er am ic s .c om