EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 1206 Package Chip LED with Inner Lens 11-21/GHC-YT1U2/2T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. Descriptions ․The 11-21 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. ․Indoor signboard use. Device Selection Guide Part No. 11-21/GHC-YT1U2/2T Chip Material InGaN Emitted Color Lens Color Brilliant Green Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Rev.1.0 Page: 1 of 10 Prepared by: Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 11-21/GHC-YT1U2/2T Package Outline Dimensions - + Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Rev.1.0 Page: 2 of 10 Prepared by: Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 11-21/GHC-YT1U2/2T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Unit VR Rating 5 Reverse Voltage Forward Current IF 30 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol 260 (for 5 second) ℃ Electrostatic Discharge ESD 150 V Power Dissipation Pd 110 mW 100 mA Peak Forward Current IFP (Duty 1/10 @1KHz) V Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 285 ----- 715 mcd Peak Wavelength λp ----- 518 ----- nm Dominant Wavelength λd ----- 525 ----- nm Spectrum Radiation Bandwidth △λ ----- 35 ----- nm Viewing Angle 2θ1/2 ----- 60 ----- deg Forward Voltage VF 3.50 4.30 ----- V Reverse Current IR ----- ----- 50 μA Condition IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Rev.1.0 Page: 3 of 10 Prepared by: Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 11-21/GHC-YT1U2/2T Bin Rang Of Dom. Wavelength Group Bin Min Max Unit Condition Y X Y Z 520 525 530 525 530 535 nm IF=20mA Bin Rang Of Luminous Intensity Bin Min Max Unit Condition T1 T2 U1 U2 285 360 450 565 360 450 565 715 mcd IF=20mA Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Rev.1.0 Page: 4 of 10 Prepared by: Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 11-21/GHC-YT1U2/2T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Rev.1.0 Page: 5 of 10 Prepared by: Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 11-21/GHC-YT1U2/2T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Rev.1.0 Page: 6 of 10 Prepared by: Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 11-21/GHC-YT1U2/2T Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Desiccant Rev.1.0 Label Page: 7 of 10 Prepared by: Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 11-21/GHC-YT1U2/2T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Rev.1.0 Page: 8 of 10 Prepared by: Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 11-21/GHC-YT1U2/2T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Rev.1.0 Page: 9 of 10 Prepared by: Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 11-21/GHC-YT1U2/2T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-111-G03 Prepared date: 08-02-04 Rev.1.0 Page: 10 of 10 Prepared by: Kenny Wang