EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 0805 Package Chip LED (1.1mm Height) 17-21/GHC-YR1S2/3T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within ROHS complaintVersion. Descriptions ․The 17-21 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 17-21/GHC-YR1S2/3T Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 Chip Material Emitted Color InGaN Brilliant Green http://www.everlight.com Prepared date:18-Aug-2005 Rev. 1 Lens Color Water Clear Page: 1 of 10 Prepared by:Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 17-21/GHC-YR1S2/3T Package Outline Dimensions - + Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 http://www.everlight.com Prepared date:18-Aug-2005 Rev. 1 Page: 2 of 10 Prepared by:Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 17-21/GHC-YR1S2/3T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40~ +90 ℃ ESD 150 V Pd 110 mW IFP 100 mA Electrostatic Discharge(HBM) Power Dissipation Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 ℃ for 10 sec. Soldering Temperature Tsol Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Luminous Intensity Iv 112 Viewing Angle 2θ1/2 ----- Peak Wavelength λp Dominant Wavelength Typ. Max. Unit 285 mcd 140 ----- deg ----- 518 ----- nm λd 520 ----- 535 nm Spectrum Radiation Bandwidth △λ ----- 35 ----- nm Forward Voltage VF ----- 3.3 3.7 V Reverse Current IR ----- ----- 50 μA Condition IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.10V Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 http://www.everlight.com Prepared date:18-Aug-2005 Rev. 1 Page: 3 of 10 Prepared by:Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 17-21/GHC-YR1S2/3T Bin Range Of Dom. Wavelength Groups Y Bin Min Max X 520 525 Y 525 530 Z 530 535 Unit Condition nm IF=20mA Bin Range Of Luminous Intensity Bin Min Max R1 112 140 R2 140 180 S1 180 225 S2 225 285 Unit Condition mcd IF=20mA Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 http://www.everlight.com Prepared date:18-Aug-2005 Rev. 1 Page: 4 of 10 Prepared by:Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 17-21/GHC-YR1S2/3T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 http://www.everlight.com Prepared date:18-Aug-2005 Rev. 1 Page: 5 of 10 Prepared by:Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 17-21/GHC-YR1S2/3T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank xxxxxx xxxxxx REF: Forward Voltage Rank RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 http://www.everlight.com Prepared date:18-Aug-2005 Rev. 1 Page: 6 of 10 Prepared by:Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 17-21/GHC-YR1S2/3T Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm. Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 Desiccant http://www.everlight.com Prepared date:18-Aug-2005 Label Rev. 1 Page: 7 of 10 Prepared by:Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 17-21/GHC-YR1S2/3T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 http://www.everlight.com Prepared date:18-Aug-2005 Rev. 1 Page: 8 of 10 Prepared by:Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 17-21/GHC-YR1S2/3T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90% RH or less. 2.3 After opening the package : The LEDs should be kept at 30℃ or less and 60% RH or less(Floor life). However, it's recommended that the LEDs should be used within 168 hours (7 days) after opening the package. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 http://www.everlight.com Prepared date:18-Aug-2005 Rev. 1 Page: 9 of 10 Prepared by:Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 17-21/GHC-YR1S2/3T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No.；SZ DSE-171-G11 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date:18-Aug-2005 Rev. 1 Page: 10 of 10 Prepared by:Meng Yali