EVERLIGHT 12-23C-R6GHBHC-A01

Technical Data Sheet
Full Color Chip LED (Chip LED with Right Angle Lens)
12-23C/R6GHBHC-A01/2C
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Multi-color type.
․Pb-free.
․The product itself will remain within RoHS compliant version.
Descriptions
․The 12-23C SMD LED is much smaller
than lead frame type components, thus
enable smaller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Chip
Emitted Color
Type
Material
R6
AlGaInP
Brilliant Red
GH
InGaN
Brilliant Green
BH
InGaN
Blue
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Resin Color
Water Clear
Rev.1
Page: 1 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Package Outline Dimensions
3.0
2.0
Blue
Green
2
1.0
3
4
Red
Anode mark
1
0.40
1.50
0.50
R1.0
4
0.40
4
3
3
2
1
1
2
Note: The tolerances unless mentioned is ±0.1mm,Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 2 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Absolute Maximum Ratings (Ta=25℃
℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
R6:25
Forward Current
IF
GH:25
mA
BH:25
R6:60
Peak Forward Current
IFP
(Duty 1/10 @1KHz)
GH:100
mA
BH:100
R6:60
Power Dissipation
Pd
GH:95
mW
BH:95
R6:2000
Electrostatic Discharge (HBM)
ESD
GH:150
V
BH:150
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +90
℃
Soldering Temperature
Tsol
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 3 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Electro-Optical Characteristics (Ta=25℃
℃)
Parameter
Luminous Intensity
Viewing Angle
Symbol
Iv
Min.
Typ.
R6
63
90
GH
125
180
BH
32
50
-----
100
2θ1/2
R6
Peak Wavelength
Dominant Wavelength
Spectrum Radiation
Bandwidth
Forward Voltage
λp
λd
GH
VF
-----
518
468
R6
624
-----
525
BH
470
R6
20
△Λ GH
-----
35
mcd
-----
deg
-----
nm
-----
nm
-----
nm
25
R6
2.0
2.4
3.3
3.9
3.3
3.9
GH
-----
GH
Condition
IF=20mA
V
10
R6
IR
-----
BH
BH
Reverse Current
Unit
632
BH
GH
Max.
-----
-----
BH
50
μA
VR=5V
50
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 4 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Typical Electro-Optical Characteristics Curves
R6
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 5 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Typical Electro-Optical Characteristics Curves
GH
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 6 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Typical Electro-Optical Characteristics Curves
BH
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 7 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Label explanation
CAT: Luminous Intensity Rank
Pb
EVERLIGHT
HUE: Dom. Wavelength Rank
CPN :
P N : XXXXXXXXXXXXX
REF: Forward Voltage Rank
RoHS
XXXXXXXXXXXXX
CAT : XXX
HUE : XXX
REF : XXX
QTY : XXX
LOT NO : XXXXXXXXXX
Reference : XXXXXXXX
MADE IN TAIWAN
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 8 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Label
Aluminum moistue-proof bag
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Desiccant
Rev.1
Label
Page: 9 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level:90%
LTPD:10%
Test
Sample
Hours/Cycles
Size
No.
Items
Test Condition
1
Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec.
6 Min.
22 PCS.
0/1
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles
22 PCS.
0/1
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles
22 PCS.
0/1
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
2
3
High Temperature
Storage
Low Temperature
Storage
4
5
Ac/Re
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/ 85% RH
1000 Hrs.
22 PCS.
0/1
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 10 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 11 of 12
Prepared by: Haizheng Gao
12-23C/R6GHBHC-A01/2C
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of the
hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No.
Prepared date: 30-Jun-2011
Rev.1
Page: 12 of 12
Prepared by: Haizheng Gao