EVERLIGHT 19-223-R6BHC-A05-2T

Technical Data Sheet
Chip LED with Bi-Color (Multi-Color)
19-223/R6BHC-A05/2T
Feature
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Multi-color type.
․Pb-free.
․The product itself will remain within RoHS compliant version.
Descriptions
․The 19-223 SMD LED is much smaller
than lead frame type components, thus
enable smaller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Type
Chip
Material
Emitted Color
R6
AlGaInP
Brilliant Red
BH
InGaN
Blue
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Resin Color
Water Clear
Rev. 2
Page: 1 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Package Outline Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 2 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
Peak Forward Current
(Duty 1/10 @1KHz)
IFP
Power Dissipation
Pd
Electrostatic Discharge (HBM)
ESD
R6:2000
BH:150
V
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +90
℃
Soldering Temperature
Tsol
R6:25
BH:25
R6:60
BH:100
R6:60
BH:95
mA
mA
mW
Reflow Soldering : 260 ℃ for 10 sec.
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
Hand Soldering : 350 ℃ for 3 sec.
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 3 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Electro-Optical Characteristics (Ta=25℃)
Parameter
Luminous Intensity
Symbol
Iv
Viewing Angle
Peak Wavelength
Min.
Typ.
Max.
R6
72.0
----
180
BH
36.0
----
72.0
-----
130
-----
deg
-----
nm
2θ1/2
λp
R6
----BH
Dominant
Wavelength
λd
R6
BH
Spectrum Radiation
Bandwidth
△λ
----
468
625
470
IR
-----
R6
1.7
2.0
2.4
BH
2.7
3.3
3.7
-----
-----
R6
IF=20mA
nm
nm
15
BH
Forward Voltage
mcd
-------
Condition
20
R6
----VF
Reverse Current
----
632
Unit
BH
10
50
V
μA
VR=5V
Notes:
1.Tolerance of Luminous Intensity ±11%
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 4 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Bin Range Of Luminous Intensity
R6
Bin
Min
Max
Q
72.0
112
R
112
180
Bin
Min
Max
N2
36.0
45.0
P1
45.0
57.0
P2
57.0
72.0
Unit
Condition
mcd
IF =20mA
Unit
Condition
mcd
IF =20mA
BH
Notes:
1.Tolerance of Luminous Intensity ±11%
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 5 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Typical Electro-Optical Characteristics Curves
R6
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 6 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Typical Electro-Optical Characteristics Curves
BH
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 7 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Label explanation
CAT: Luminous Intensity Rank
Pb
EVERLIGHT
CPN :
P N : XXXXXXXXXXXXX
HUE: Dom. Wavelength Rank
RoHS
REF: Forward Voltage Rank
XXXXXXXXXXXXX
CAT : XXX
HUE : XXX
REF : XXX
QTY : XXX
LOT NO : XXXXXXXXXX
Reference : XXXXXXXX
MADE IN TAIWAN
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 8 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Label
Aluminum moisture-proof bag
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Desiccant
Rev. 2
Label
Page: 9 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level:90%
LTPD:10%
Test
Sample
Hours/Cycles
Size
No.
Items
Test Condition
1
Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec.
6 Min.
22 PCS.
0/1
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles
22 PCS.
0/1
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles
22 PCS.
0/1
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
2
3
4
5
High Temperature
Storage
Low Temperature
Storage
Ac/Re
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/ 85%RH
1000 Hrs.
22 PCS.
0/1
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 10 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 11 of 12
Prepared by : Cheng Dejiang
19-223/R6BHC-A05/2T
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within
once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Everlight Electronics Co., Ltd.
Device No:DSE-0001563
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
http://www.everlight.com
Prepared date:22-May-2008
Rev. 2
Page: 12 of 12
Prepared by : Cheng Dejiang