2.1x0.7 mm RIGHT ANGLE SMD CHIP LED LAMP APJA2107SURC Features HYPER RED Description 2.1mmx0.7mm RIGHT ANGLE SMT LED, 1.3mm THICKNESS. The Hyper Red source color devices are made LOW POWER CONSUMPTION. with DH InGaAlP on GaAs substrate Light Emitting WIDE VIEWING ANGLE. Diode. IDEAL FOR BACKLIGHT AND INDICATOR. VARIOUS COLORS AND LENS TYPES AVAILABLE. PACKAGE : 2000PCS / REEL. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD1025 REV NO: V.5 DATE: JUN/29/2005 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN PAGE: 1 OF 5 ERP:1203001551 Selection Guide Part No. Dice HYPER RED (InGaAlP) APJA2107SURC Iv (mcd) @ 20mA Lens Type WATER CLEAR Viewing Angle Min. Typ. 2θ θ1/2 70 200 120° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device λpeak Peak Wavelength Hyper Red λD Dominant Wavelength ∆λ1/2 Typ. Max. Units Test Conditions 640 nm IF=20mA Hyper Red 628 nm IF=20mA Spectral Line Half-width Hyper Red 27 nm IF=20mA C Capacitance Hyper Red 45 pF VF=0V;f=1MHz VF Forward Voltage Hyper Red 1.9 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units 170 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Power dissipation Reverse Voltage Operating/Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1025 REV NO: V.5 DATE: JUN/29/2005 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN PAGE: 2 OF 5 ERP:1203001551 Hyper Red APJA2107SURC SPEC NO: DSAD1025 REV NO: V.5 DATE: JUN/29/2005 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN PAGE: 3 OF 5 ERP:1203001551 APJA2107SURC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAD1025 REV NO: V.5 DATE: JUN/29/2005 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN PAGE: 4 OF 5 ERP:1203001551 PACKING & LABEL SPECIFICATIONS APJA2107SURC SPEC NO: DSAD1025 REV NO: V.5 DATE: JUN/29/2005 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN PAGE: 5 OF 5 ERP:1203001551