4.0x3.0mm RIGHT ANGLE SMD CHIP LED LAMP APEKA4030SURC HYPER RED Description Features 4.0mmx3.0mm RIGHT ANGLE SMT LED, 2.65mm The Hyper Red source color devices are made THICKNESS. with DH InGaAlP on GaAs substrate Light Emitting Diode. LOW POWER CONSUMPTION. WIDE VIEWING ANGLE. IDEAL FOR BACKLIGHT AND INDICATOR. PACKAGE :500PCS / REEL. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD1184 REV NO: V.2 DATE: JUN/30/2005 PAGE: 1 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000024 Selection Guide Part No. Dice HYPER RED (InGaAlP) APEKA4030SURC Iv (mcd) @ 20mA Lens Type WATER CLEAR Viewing Angle Min. Typ. 2θ θ1/2 70 250 90° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device λpeak Peak Wavelength Hyper Red λD Dominant Wavelength ∆λ1/2 Typ. Max. Units Test Conditions 640 nm IF=20mA Hyper Red 628 nm IF=20mA Spectral Line Half-width Hyper Red 27 nm IF=20mA C Capacitance Hyper Red 45 pF VF=0V;f=1MHz VF Forward Voltage Hyper Red 1.9 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 170 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating/Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1184 REV NO: V.2 DATE: JUN/30/2005 PAGE: 2 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000024 Hyper Red APEKA4030SURC SPEC NO: DSAD1184 REV NO: V.2 DATE: JUN/30/2005 PAGE: 3 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000024 APEKA4030SURC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) SPEC NO: DSAD1184 REV NO: V.2 DATE: JUN/30/2005 PAGE: 4 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000024 PACKING & LABEL SPECIFICATIONS APEKA4030SURC Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAD1184 REV NO: V.2 DATE: JUN/30/2005 PAGE: 5 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000024