LUGUANG ES1D

ES1A-ES1J
1.0 AMPS. Surface Mount Super Fast Rectifiers
SMA/DO-214AC
Features
Glass passivated junction chip
For surface mounted application
Low profile package
Built-in strain relief,
Ideal for automated placement
Easy pick and place
Super fast recovery time for high efficiency
Glass passivated chip junction
High temperature soldering:
O
260 C/10 seconds at terminals
Plastic material used carries Underwriters
Laboratory Classification 94V-0
Mechanical Data
Cases: Molded plastic
Terminals: Pure tin plated, lead free.
Polarity: Indicated by cathode band
Packing: 12mm tape
Weight: 0.064 gram
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25 OC ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Symbol ES ES ES ES ES ES ES ES
Type Number
Units
1A 1B 1C 1D 1F 1G 1H 1J
Maximum Recurrent Peak Reverse Voltage
V
VRRM 50 100 150 200 300 400 500 600
35
70
105
140
210
280
350
420
Maximum RMS Voltage
V
VRMS
Maximum DC Blocking Voltage
VDC
Maximum Average Forward Rectified Current
See Fig. 1
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
Maximum Instantaneous Forward Voltage
@ 1.0A
50
100 150 200 300 400 500 600
I(AV)
1.0
A
IFSM
30
A
VF
0.95
1.3
o
Maximum DC Reverse Current @ TA =25 C
o
at Rated DC Blocking Voltage @ TA=100 C
IR
Maximum Reverse Recovery Time ( Note 1 )
Trr
Typical Junction Capacitance ( Note 2 )
Maximum Thermal Resistance (Note 3)
Operating Temperature Range
Cj
RθJA
RθJL
TJ
1.7
V
5.0
100
35
10
uA
uA
nS
pF
8
85
35
-55 to +150
-55 to +150
Storage Temperature Range
TSTG
1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
Notes:
2. Measured at 1 MHz and Applied VR=4.0 Volts
3. P.C.B. Mounted on 0.2 x 0.2” (5.0 x 5.0mm) Copper Pad Area.
http://www.luguang.cn
V
mail:[email protected]
o
C /W
o
C
C
o
ES1A-ES1J
1.0 AMPS. Surface Mount Super Fast Rectifiers
RATINGS AND CHARACTERISTIC CURVES (ES1A THRU ES1J)
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
FIG.2- TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
50
1.2
0
80
90
100
110
120
130
140
150
o
LEAD TEMPERATURE. ( C)
-D
1G
1A
ES
1F
-1
J
0.2
1
1H
0.4
ES
0.6
10
ES
RESISTIVE OR
INDUCTIVE LOAD
0.2X0.2"(5.0X5.0mm)
COPPER PAD AREAS
0.8
INSTANTANEOUS FORWARD CURRENT. (A)
AVERAGE FORWARD CURRENT. (A)
0
Tj=25 C
PULSE WIDTH-300 S
1% DUTY CYCLE
1.0
0.1
30
8.3ms Single Half Sine Wave
o
(JEDEC Method) at TL=120 C
25
0.01
0.4
0.8
1.0
1.2
1.4
1.6
1.8
20
15
10
FIG.5- TYPICAL REVERSE CHARACTERISTICS
1000
5.0
100
10
1
NUMBER OF CYCLES AT 60Hz
FIG.4- TYPICAL JUNCTION CAPACITANCE
14
JUNCTION CAPACITANCE.(pF)
0.6
FORWARD VOLTAGE. (V)
Tj=25 0C
f=1.0MHz
Vsig=50mVp-p
12
ES1
10
ES
8.0
1F
A-
D
-J
6.0
INSTANTANEOUS REVERSE CURRENT. ( A)
PEAK FORWARD SURGE CURRENT. (A)
FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
100
Tj=125 0C
10
Tj=85 0C
Tj=25 0C
0.1
4.0
2.0
0
1
0
0.01
100
10
0
REVERSE VOLTAGE. (V)
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
10W
NONINDUCTIVE
trr
+0.5A
(-)
DUT
(+)
50Vdc
(approx)
(-)
PULSE
GENERATOR
(NOTE 2)
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
0
-0.25A
(+)
-1.0A
1cm
SET TIME BASE FOR
5/ 10ns/ cm
Version: B07
http://www.luguang.cn
mail:[email protected]