HS2A-HS2M 2.0AMP. High Efficient Surface Mount Rectifiers SMB/DO-214AA .083(2.10) .077(1.95) .147(3.73) .137(3.48) Features Glass passivated junction chip. For surface mounted application Low forward voltage drop Low profile package Built-in stain relief, ideal for automatic placement Fast switching for high efficiency High temperature soldering: o 260 C/10 seconds at terminals Plastic material used carries Underwriters Laboratory Classification 94V0 .187(4.75) .167(4.25) .012(.31) .006(.15) .103(2.61) .078(1.99) .012(.31) .006(.15) .056(1.41) .035(0.90) .008(.20) .004(.10) .209(5.30) .201(5.10) Mechanical Data Dimensions in inches and (millimeters) Cases: Molded plastic Terminals: Pure tin plated, lead free Polarity: Indicated by cathode band Packing: 12mm tape per Weight: 0.093 gram Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol HS Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 2.0A Maximum DC Reverse Current @ T A =25 oC at Rated DC Blocking Voltage @ T A=125 oC Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Maximum Thermal Resistance (Note 3) Operating Temperature Range V RRM V RMS V DC 2A HS 2B HS 2D HS 2F HS 2G HS 2J HS 2K HS 2M 50 35 50 400 200 300 400 600 800 1000 70 140 210 280 420 560 700 100 200 300 400 600 800 1000 V V V I(AV) 2.0 A IFSM 50 A VF 1.0 1.3 5.0 150 IR Trr Cj R θJA TJ 1.7 50 50 75 30 80 -55 to +150 -55 to +150 Storage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A Notes: 2. Measured at 1 MHz and Applied V R =4.0 Volts. 3.Mounted on P.C.Board with 0.4” x 0.4” (10mm x 10mm) Copper Pad Area. http://www.luguang.cn Units mail:[email protected] V uA uA nS pF o C/W o C o C HS2A-HS2M 2.0AMP. High Efficient Surface Mount Rectifiers RATINGS AND CHARACTERISTIC CURVES (HS2A THRU HS2M) FIG.2- TYPICAL REVERSE CHARACTERISTICS FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1000 2.5 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) 3.0 2.0 1.5 1.0 0.5 0 0 25 50 75 100 125 150 175 O LEAD TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT Tj=100 0C 100 10 Tj=25 0C 1 0.1 60 50 20 40 60 80 100 120 140 8.3ms Single Half Sine Wave JEDEC Method 40 30 FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 10 10 10 20 50 100 FIG.4- TYPICAL JUNCTION CAPACITANCE 175 150 125 100 HS HS 50 2J- 2A- HS 2G 0.1 0.01 HS -HS2 75 1 HS 2G 5 NUMBER OF CYCLES AT 60Hz M 2 1 HS2 A-HS 2D 0 2M HS2J JUNCTION CAPACITANCE.(pF) 0 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) INSTANTANEOUS FORWARD CURRENT. (A) PEAK FORWARD SURGE CURRENT. (A) 70 25 0 0.1 0.001 0.2 0.5 1 2 5 10 20 50 100 200 500 1000 0 0.2 0.4 REVERSE VOLTAGE. (V) 0.6 0.8 1.0 FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms http://www.luguang.cn 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm mail:[email protected] 1.2 1.4