ASP-149118-01 REVISION CL "A" R2.30 (4 PLCS) CL "A" NOT RELEASED FOR PRODUCTION TRUE R1.30 (8 PLCS) 8.000 USE FOR QUOTING, PRELIMINARY DESIGN, PROTOTYPING AND INFORMATIONAL PURPOSES ONLY 0.10 -W28.00±0.10 -Z14.82 -X- 13.62 14.00 CL 26.00 0.70 (2 PLCS) "B" 0.10 CL -Y- 3.00 (2 PLCS) 8.87±0.10 M1.60 x 0.35 THRU (2 PLCS) 9.874 18.12 4.50 "B" R1.00 (TYP) 32.49 3.24 (TYP) R0.50 (TYP) 13.87 8.50 11.25 SEE NOTE 2 C2 R1.50 (TYP) 26.63 M1.6 x 0.35 3.80 (2 PLCS) 0.10 W X Y 5° C1 2.400 (2 PLCS) 0.10 W X Y 6.0 (TYP) 29.31 24.75 26.91 M1.6 x 0.35 4.50 (2 PLCS) NOTES: 1. REPRESENTS A CRITICAL DIMENSION. 2. SAMTEC SHALL APPEAR ON SURFACE SHOWN, APPROXIMATELY 3. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN 0.05 OFF THE SURFACE OF THE PART. 4. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE FREE OF SCRATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES. 5. PARTS TO BE PACKAGED IN TRAYS. 6. ALL DRAFT MUST BE WITHIN TOLERANCES. 7. PARTS TO BE SHOT BLASTED. 8. DIMENSION TO BE ADJUSTABLE IN THE DIE. C UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS. TOLERANCES ARE: DECIMALS X.X: 0.3 X.XX: 0.13 X.XXX: 0.025 ANGLES 2 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING MATERIAL: ZAMAK 3 PLATING: Cu: 0.008 - 0.015 mm [.0003 - .0006 in.] UNDERPLATE Ni: 0.003 - 0.008 mm [.0001 - .0003 in.] MAX GATE VESTIGE: 0.13 MAX FLASH ALLOWED: 0.08 SHEET SCALE: 2:1 F:\DWG\SW\Newprod\Pt635mm\HyperTransport\ASP-149118-01.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: [email protected] code: 55322 DESCRIPTION: DWG. NO. 0.635MM EDGE MOUNT PCB CAGE ASP-149118-01 BY: VICKY Z 12/09/2009 SHEET 1 OF 2 REVISION 0 28.00 REF -X- 26.70 0.10 X Z 30° 1.54 25.83±0.05 0.10 X C3 3.483 'D' 6.631 1.95 (TYP) 1.00 (TYP) 'E' 1.75 (TYP) 'C' SECTION "A"-"A" 1.000 C4 0.10 X SECTION "B"-"B" 0.20 9.874 REF 20° 0.39 45° C7 C5 4.85±0.05 (TYP) 0.10 Z 2.35±0.05 (TYP) (SEE NOTE 8) 2.00 25.83 REF 0.09 REF 1.50 R0.40 (TYP) C6 5.75±0.05 (TYP) 0.10 Z 1.55 DETAIL 'E' SCALE 8 : 1 DETAIL 'D' SCALE 8 : 1 DETAIL 'C' SCALE 4 : 1 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. SHEET SCALE: 2:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: [email protected] code: 55322 DESCRIPTION: DWG. NO. F:\DWG\SW\Newprod\Pt635mm\HyperTransport\ASP-149118-01.SLDDRW 0.635MM EDGE MOUNT PCB CAGE ASP-149118-01 BY: VICKY Z 12/09/2009 SHEET 2 OF 2