Technical Document
LCD Specification
LCD Group
LS013B4DN01 LCD Module
Preliminary Product Specification
April 2009
96 × 96 Silver Reflective PNLC Memory LCD
Module featuring Zebra (elastomeric) connector,
50% reflectivity with 10:1 contrast.
No.
LCY-12T09302A
Date
April. 24th 2009
TECHNICAL LITERATURE
For
TFT-LCD Module
Model No. LS013B4DN01
Notice
The technical Literature is subject to change without any prior
notice for the purpose of product improvement.
Please contact Sharp or its representative before designing
your product based on this literature.
Mobile Liquid Crystal Display Group
SHARP CORPORATION
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
1
<<Precautions>>
NOTICE
○ These specification sheets are the proprietary product of SHARP CORPORATION ("SHARP") and include materials protected
under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic
or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP.
○ The application examples in these specification sheets are provided to explain the representative applications of the device and
are not intended to guarantee any industrial property right or other rights or license you to use them. SHARP assumes no
responsibility for any problems related to any industrial property right of a third party resulting from the use of the device.
○SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents
described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest
specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice.
Observe the following points when in using any device in this publication. SHARP takes no responsibility
for damage caused by improper use of the devices.
The devices in this publication are designed for use in general electronic equipment designs, such as:
・Personal computers
・Office automation
・Test and measurement equipment
・Telecommunication equipment
・Industrial control
・Audio visual and multimedia equipment
・Consumer electronics
The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are
used for equipment such as:
・Transportation control and safety equipment(i.e.,aircraft,trains,automobiles,etc.)
・Traffic signals
・Alarm equipment
○
・Gas leakage sensor breakers
・Various safety devices etc.
SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as:
・Military and space applications
・Nuclear power control equipment
・Medical equipment for life support
○ SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the
instructions and the precautions specified in these specification sheets.
○ Contact and consult with a SHARP sales representative for any questions about this device.
.
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
2
[For handling and system design]
(1) It is recommended to handle LCD panel with carefully, since this LCD panel is made of thin glass, dropping the module or
banging it against hard objects may cause cracks or fragmentation.
(2) Do not scratch the surface of the UV protection film as it is easily damaged.
(3) Water droplets on the UV protection film must be wiped off immediately as they may cause color changes, or other defects if
remained for a long time.
(4) If the cleaning of the surface of the LCD panel is necessary, wipe it swiftly with cotton or other soft cloth.
Do not use organic solvents as it damages the UV protection film.
(5) Do not hold or touch the part of single glass of LCD panel which has electric connection area, as electric circuits in LCD
panel may be damaged.
(6) Hold LCD with very carefully when placing LCD module into the system housing.
(7) LCD panel is susceptible to mechanical stress and even the slightest stress will cause a color change in background. So make
sure the LCD panel is placed on flat plane without any continuous twisting, bending or pushing stress.
(8) When carrying the LCD module, place it on the tray to protect from mechanical damage. It is recommended to use the
conductive trays to protect LCD panel from electrostatic discharge. Certain materials such as epoxy resin (amine’s hardener) or
silicone adhesive agent (de-alcohol or de-oxym) emits gas to which the UV protection film reacts (color change).
Check carefully that gas from materials used in system housing or packaging do not hart the UV protection film.
(9)Do not apply excessive stress or pressure to LCD module. Do not to use chloroprene rubber as it may affect on the reliability
of the electrical interconnection.
(10) As this LCD module contains components sensitive to electrostatic discharge, more than 200V, be sure to follow the
instructions in below.
① Operators
Operators must wear anti-static wears to prevent electrostatic charge up to and discharge from human body.
② Equipment and containers
Process equipment such as conveyer, soldering iron, working bench and containers may possibly generate electrostatic charge
up and discharge. Equipment must be grounded through 100Mohms resistance. Use ion blower.
③ Floor
Floor is an important part to leak static electricity which is generated from human body or equipment.
There is a possibility that the static electricity is charged to them without leakage in case of insulating floor, so the
electrostatic earth should be lower than the 1×108Ω.
④Humidity
Proper humidity of working room may reduce the risk of electrostatic charge up and discharge. Humidity should be kept over
50% all the time.
⑤Transportation/storage
Storage materials must be anti-static to prevent causing electrostatic discharge.
⑥Others
(11) Protective film is attached on the surface of the UV protection film on LCD panel to prevent scratches or other damages.
When removing this protective film, remove it slowly under proper anti-ESD control such as ion blower.
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
3
[For operating LCD module]
(1) Do not operate the LCD panel under outside of electrical specification. Otherwise LCD panel may be damaged.
(2) Do not operate the LCD panel under outside of specified driving timing chart. Otherwise LCD panel may not have proper
picture quality.
(3) A still image should be displayed less than two hours, if it is necessary to display still image longer than two hour, display
image data must be refreshed in order to avoid sticking image on LCD panel.
[Precautions for Storage]
(1) Do not expose the LCD module to direct sunlight or strong ultraviolet light for long periods. Store in a dark place.
(2) The liquid crystal material will solidify if stored below the rated storage temperature and
will become an isotropic liquid if
stored above the rated storage temperature, and may not retain its original properties. Only store the module at normal
temperature and humidity (25±5°C,60±10%RH) in order to avoid exposing the UV protection film to chronic humidity.
(3) Keeping Method
a. Don't keeping under the direct sunlight.
b. Keeping in the tray under the dark place.
SPEC
No.
LCY-12T09302A
MODEL
No.
PAGE
LS013B4DN01
4
[Other Notice]
(1) Do not operate or store the LCD module under outside of specified environmental conditions.
(2) As electrical impedance of power supply lines (VDD-VSS) are low when LCD module is working, place the de-coupling
capacitor near by LCD module as close as possible.
(3) Although the LCD panel has the UV protection film on the LCD panel surface, just in case, do not expose the LCD module to
direct sunlight or strong ultraviolet light for long periods.
(4) Do not disassemble the LCD module as it may cause permanent damage.
(5) Since the liquid crystal is injurious, do not put it into the eyes
or mouth. When liquid crystal sticks to hands, feet or clothes, wash it out immediately with soap.
(6) This LCD module does not contain nor use any ODS (1,1,1-Trichloroethane, CCL4) in all materials used, in all production
processes.
(7) Observe all other precautionary requirements in handling general electronic components.
[Precautions for Discarding Liquid Crystal Modules]
LCD panel: Dispose of as glass waste. This LCD module contains no harmful substances. The liquid crystal panel contains no
dangerous or harmful substances. The liquid crystal panel only contains an extremely small amount of liquid crystal
(approx.100mg) and therefore it will not leak even if the panel should break.
-Its median lethal dose (LD50) is greater than 2,000 mg/kg and a mutagenetic (Aims test: negative) material is employed.
SPEC
No.
LCY-12T09302A
MODEL
No.
LS013B4DN01
Contents
1. Outline ･･･････････････････････････････････････････････････････････････････････････P6
2. Characteristics ････････････････････････････････････････････････････････････････････P6
3.Mechanical Specification･････････････････････････････････････････････････････････････P6
4.Input terminal specification･･･････････････････････････････････････････････････････････P7
5.Absolute Maximum Rating･･･････････････････････････････････････････････････････････P8
6.Electrical Specification･･･････････････････････････････････････････････････････････････P8
7.Optical Chracteristics････････････････････････････････････････････････････････････････P18
8.LCD Module Outline Dimensions･････････････････････････････････････････････････････P20
9.External capacitor････････････････････････････････････････････････････････････････････P21
10.External power supply･･･････････････････････････････････････････････････････････････P22
11.Zebra Connector････････････････････････････････････････････････････････････････････P23
12.Packaging ･････････････････････････････････････････････････････････････････････････P24
13.Reliability test ････････････････････････････････････････････････････････････････････P26
PAGE
5
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
6
LS013B4DN01
1.Outline
This TFT-LCD module is a reflective active matrix memory liquid crystal display module
with CG silicone thin film transistor.
Module outline is indicated in Table 8-1.
2.Characteristics
・Reflective panel of white and black with aspect ratio of 1:1
・1.35” screen has 96x 96 resolusion.( 9216 pixels stripe array)
・Display control by serial data signal communication.
・Arbitrary line data renewable.
・1bit internal memory for data storage within the panel.
・Thin, light-weight and compact module with monolithic technology.
・Super low power consumption TFT panel.
・Zebra connecter
3．Mechanical Specification
Table 3-1
Item
Specification
unit
Screen size
1.35
Inch
Viewing Area
24 (H) × 24 (V)
mm
Dot configuration
96 (H) ×
Dot
Dot pitch
0.252 (H) × 0.252 (V)
mm
Pixel Array
Stripe Array
-
Outline Dimension
28.2 (W) × 32.34 (H) × 1.4 (D)
mm
Mass
3.6 (TYP）
g
Surface Hardness
3H
Pencil hardness
96 (V)
（Note） Detail dimension and tolerance are shown in fig. 8-1
SPEC
No.
MODEL
LCY-12T09302A
4．Input terminal names and functions
Table4-1
Terminal
Symbol
I／O
1
TEST1
2
TEST2
-
No.
LS013B4DN01
Function
Test terminal
Test terminal
3
SCLK
INPUT
Serial clock signal
4
SI
INPUT
Serial Data input signal
5
SCS
INPUT
Chip select signal
6
EXTCOMIN
INPUT
External COM inversion signal input (H: enable)
7
DISP
INPUT
Display ON/OFF signal
8
VDDA
POWER
Power supply (Analog)
9
VDD
POWER
Power supply (Digital)
10
EXTMODE
INPUT
COM inversion select terminal
11
VSS
POWER
GND(Digital)
12
VSSA
TEST3
TEST4
POWER
-
GND(Analog)
13
14
Test terminal
Test terminal
PAGE
7
Remark
【Remark4-1】
【Remark4-1】
【Remark4-3】
【Remark4-2】
【Remark4-1】
【Remark4-1】
【Remark4-1】TEST terminal: OPEN these test terminals.
【Remark4-2】When it’s ”H”, EXTCOMIN signal is enable. And when it’s ”L” ,serial input flag is enable.
“H”mode; connect the EXTMODE toVDD, ”L” mode; connect the EXTMODE to VSS.
【Remark4-3】The display ON/OFF signal is only for display. Data in the memory will be saved at the time of ON/OFF.
When it’s ”H”, data in the memory will display, when it’s ”L”, white color will diaplay and data in the memory will be
saved.
4-2）Recommended circuit;
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
8
LS013B4DN01
5．Absolute maximum rating
Table5-1 （GND＝0V）
Item
Power
supply
voltage
Analog
Logic
Symbol
MIN.
MAX.
Unit
VDDA
-0.3
＋5.8
V
VDD
-0.3
＋5.8
V
[Remark5-1]
VDD
V
[Remark5-2]
Input signal voltage(high)
Input signal voltage(low)
-0.3
Strage Temperature
Operation Temperature
panel surface)
(at
Remark
V
Tstg
-30
＋80
℃
[Remark5-3,4]
Topr1
-20
＋70
℃
[Remark5-5]
[Remark5-1] Applies to EXTMODE.
[Remark5-2] Applies to SCLK, SI, SCS, DISP, EXTCOMIN.
[Remark5-3] Do not exceed this temperature in any parts of module.
[Remark5-4] Maximum wet bulb temperature is 57℃ or lower. No condensation is allowed.
Cndensation will cause electeical leak and may cause the module to not meet this specification.
[Remark5-5] Operating temperature is the temperature that guarantees only the operation.
For contrast, response time, and other display quality determination, use Ta＝＋25℃.
6．Electrical characteristics
6-1）TFT LCD panel Drive
Table6-1 Recommended operating Condition
Item
Power supply
Input signal voltage
Input leak current
VSS(GND)＝0V、Ta＝＋25℃
symbol
MIN.
TYP.
MAX.
Unit
VDDA
＋4.8
＋5.0
＋5.5
V
Logic
VDD
＋4.8
＋5.0
＋5.5
V
[Remark6-1]
Hi
VIH
＋2.70
＋3.00
※VDD
V
[Remark6-2]
Lo
VIL
VSS
VSS
VSS+0.15
V
Hi
IOH
-
-
TBD
uA
[Remark6-2]
VI=3V
Lo
IOL
-
-
TBD
uA
[Remark6-2]
VI=0V
Analog
※ Lower 3V is recommended, and it’s lower than the VDD voltage.
[Remark6-1] Applies to EXTMODE＝”H”
[Remark6-2] Applies to SCLK, SI, SCS, DISP, EXTCOMIN.
Remark
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
6-2）Power supply sequence
[On sequence] * All on start up System
①5V start up
②Initializes memory data within pixel
T2 : more than 1V
Initialize with D2 "all clear flag" or display all white.
③To cancel latch initialization for TCOM.
T3 : more than 30us
The period of canceling COM latch circuit for initialization by using DISP signal.
④TCOM polarity initialization
T4: more than 30us
The period of initialization for TCOM polarity by EXTCOMIN signal.
[Normal operation]
Duration of normal driving.
[Off sequence]
⑤Initializes memory data within pixel
⑥The period of initialization for VA, VB, and VCOM
⑦5V shut down
Normal operation
On Sequence
①
②
T1
T2
T5 : more than 1V
T6 : more than 1V
③※1 ④※1
T3
T4
Off Sequence
⑤
⑥
⑦
T5
T6
T7
VDD/VDDA (5V)
GND
GND
DISP
GND
GND
EXTCOMIN
GND
SCS
GND
※2
Normal operation
※2
GND
Others
GND
※2
Normal operation
※2
GND
Normal operation
GND
※Detail description for signal timing is shown the digital timing chart and the AC timing chart.
※1 The order of ③ and ④ can be set as being reversed, in this case, TCOM polarity inversion timing which can be controlled
by EXTCOMIN doesn't work during DISP="L".
※2 Setup value for initialization of data within pixel memory
To refer the timing chart of all clear mode section 6-5-4.
[Remark] Precaustions at ehte time of power on and power off.
Remark 1)When power on , VDDand VDDA are same timem or VDD should be faster than the VDDA.
Remark 2) When power off, VDD and VDDA are same time or VDDA shoud be faster than the VDD.
9
SPEC
No.
MODEL
LCY-12T09302A
6-3）Input signal characteristics
Table6-3-1
No.
PAGE
VDDA=＋5.0V、VDD=＋5.0V、GND=0V、Ta=25℃
Item
Symbol
MIN
TYP
MAX
Unit
Frame frequency
fSCS
1
-
60
Hz
Clock frequency
fSCLK
1
2
MHz
Vertical Interval
tV
16.66
-
1000
ms
COM Frequency
fCOM
0.5
-
30
Hz
Table 6-3-2
10
LS013B4DN01
Remark
VDDA=＋5.0V、VDD=＋5.0V、GND=0V、Ta=25℃
Item
Symbol
MIN
TYP
MAX
Unit
SCS Rising time
trSCS
-
-
50
ns
SCS Falling Time
tfSCS
-
-
50
ns
SCS High duration
twSCSH
68
-
-
us
[Remark 6-4]
12
-
-
us
[Remark 6-5]
(1)
-
-
us
SCS Low duration
twSCSL
SCS set up time
tsSCS
(3)
-
-
us
SCS hold time
thSCS
(1)
-
-
us
SI frequency
fSI
-
0.5
1
MHz
SI Rising time
trSI
-
-
50
ns
SI Folling time
tfSI
-
-
50
ns
SI set up time
tsSI
(120)
-
-
ns
SI hold time
thSI
(125)
-
-
ns
SCLK Rising time
trSCLK
-
-
50
ns
SCLK Folling time
tfSCLK
-
-
50
ns
SCLK High duration
twSCLKH
200
450
-
ns
SCLK Low duration
twSCLKL
200
450
-
ns
EXTCOMIN signal freequency
fEXTCOMIN
1
60
Hz
EXTCOMIN signal rising time
trEXTCOMIN
-
-
50
ns
EXTCOMIN signal folling time
tfEXTCOMIN
-
-
50
ns
EXTCOMIN signalHigh duration
thlEXTCOMIN
1
DISP Rising time
trDISP
-
-
50
ns
DISP Folling time
tfDISP
-
-
50
ns
us
( ) is tentative valure.
[Remark6-4] Data renew mode.
[Remark6-5] Display mode.
[Remark6-6] Adjust EXTCOMIN frequency to be lower than the frame frequency.
Remark
[Remark6-6]
SPEC
No.
MODEL
LCY-12T09302A
SCS、SI、SCLK Signal
SCS
No.
PAGE
twSCSL
twSCSH
90%
90%
50%
10%
trSCS
tsSCS
SI
10%
thSCS
90%
90%
10%
10%
10%
trSI
tfSI
tsSI
SCLK
thSI
twSCLKH twSCLKL
50%
90% 90%
trSCLK
twEXTCOMINH
90%
50%
10%
10%
trEXTCOMIN
tfEXTCOMIN
DISP Signal
DISP
90%
90%
10%
10%
trDISP
90%
50%
tfSCLK
EXTCOMIN Signal
90%
50%
10%
10%
EXTCOMIN
11
LS013B4DN01
tfDISP
※SCS,SI,SCLK、DISP: 3V Amplitude
EXTCOMIN : 5V amplitude.
50%
twEXTCOMINL
50%
50%
10%
tfSCS
50%
SPEC
No.
MODEL
LCY-12T09302A
6-4）Power consumption (Average)
Table6-4
Item
Symbol
No.
PAGE
12
LS013B4DN01
Ta＝25℃
MIN
TYP
MAX
unit
Remark
Condition1
15
uW
[Remark6-6]
Condition2
30
uW
[Remark6-6]
＊Condition1
Display mode (No display data update)
Common AC Driving with VDD=5V, VDDA=5V, fSCLK=1MHz, fSCS=１Hz, Display pattern: Vertical stripe display
＊Condition 2
Data Renew mode (With display data update: 1Hz)
Common AC Driving with VDD=5V, VDDA=5V, fSCLK=1MHz, fSCS=１Hz, Display pattern: Vertical stripe display
[Remark6-6] This is the average power in normal condition, not the peak power for COM driving.
Allow margin in power supply. Use of capacitor is recommended for VDD+VDDA.
(If VDD and VDDA are separate, use of capacitor on each is recommended.)
6-5）Input Signal Timing Chart
6-5-1 Data Renew Mode (1 line)
Renews data on one specified line. (M0=”H”, M2=”L”)
twSCSL
twSCSH
SCS
thSCS
tsSCS
SI
M0 M1 M2 DMYDMYDMYDMYDMY AG0 AG1 AG2 AG3 AG4 AG5 AG6 DMY D1
tsSI
thSI
twSCLKL
D2
D3
D4
D93 D94 D95 D96
DUMMY DATA(don't care)
twSCLKH
SCLK
Mode selection period
(3ck+5ckDMY)
Gate line address period
(7ck+1ckDMY)
Data writing period
(96ck)
Data transfer period
(16ck)
・M0：Mode flag: If M0 is "H". -> Data refresh mode "Pixel data will be updated" . If M0 is "L" -> Display mode "Pixel data is held.
・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output. If M1 is "L" then VCOM="L" is output. In addition, if EXTMODE is set as "H", M1 set value doesn't matter.
・M2：All flags are cleared. If M2 is "L" then all flags are cleared.
When all clear are needed, refer to "all clear timing chart"
・D1 - D96：Display data: If D* is "L" then Black display can be appeared, if D* is "H" then White display can be appeared
※In terms of Data writing period
Data has been stored in 1st latch block of Binary driver on
Panel.
・DUMMY DATA： Dummy data. Don't care but "L" is recommended
※In term of Data transfer period
The data which has been stored in 1st latch block is
transferred to pixel memory.
Renews data on one specified line. (M0=”H”, M2=”L”)
※Refer to 6-6) Input Signal and Display for gate line address setting.
※M1:
Frame inversion flag is enabled when EXTMODE=”L”.
※When SCS becomes L, M0 and M2 are cleared.
※In renew mode (When M2=”H”) do “All Clear”, and set P1 through P96 as L.
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
13
LS013B4DN01
6-5-2 Data Renew Mode
Updates multiple line data. (M0=”H”, M2=”L”)
twSCSH
SCS
tsSCS
SI
M0
tsSI
M1
M2
DMY
thSI
DMY
DMY
DMY
twSCLKL
DMY
AG0
AG1
AG2
AG3
AG4
AG5
AG6
DMY
D1
D2
D3
D4
D93
D94
D95
D96
DUMMY DATA(don't care)
AG0
AG1
AG5
AG6
DMY
D1
twSCLKH
SCLK
Gate line address period
(7ck+1ckDMY)
GL1
Mode selection period
(3ck+5ckDMY)
Data transfer period
(96ck)
Data transfer period
(8ck(Dummy)+7ck(address)+1ck(Dummy)=16ck)
GL2
twSCSH
twSCSL
thSCS
D95
D96
DUMMY DATA(don't care)
AG0
AG1
AG4
AG5
AG6
Data transfer period
(8ck(Dymmy)+7ck(address)+1ck(Dummy)=16ck)
GL(n)th line
GL(n-1)th Line
DMY
D1
D2
D94
D95
D96
Data writing period
(96ck)
DUMMY DAT A(don't care)
Data transfer period
(16ck)
・M0：Mode flag: If M0 is "H" then Data refresh mode "Pixel data will be updated, If M0 is "L" then display mode "Pixel data is held"
・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output. If M1 is "L" then VCOM="L" is output.
In addition, if EXTMODE is set as "H", M1 set value doesn't matter.
・M2：All flags are cleared. If M2 is L then all flags are cleared.
When all clear are needed, refer to "all clear timing chart"
・D1 - D96：Display data: If D* is "L" then Black display can be appeared, if D* is "H" then White display can be appeared
・DUMMY DATA： Dummy data. Don't care but "L" is recommended
※In terms of Data writing period
Data has been stored in 1st latch block of Binary driver on Panel.
※In term of Data transfer period
As an example, the 1st latch block in binary driver which stored the data of 1st gate line"GL1"output the data to GL1 and store the data
for 2nd gateline"GL2" at same time.
※Refer to 6-6) Input Signal and Display for gate line address setting.
※Input data continuously.
※M1:
Frame inversion flag is enabled when EXTMODE=”L”.
※When SCS becomes L, M0 and M2 are cleared.
※In renew mode (When M2=”H”) do “All Clear”, and set P1 through P96 as L.
D2
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
6-5-3 Display mode
Maintains data in the memory(Maitain the current display)(M0=”L”、M2＝”L”)
tV
twSCSH
twSCSL
SCS
thSCS
tsSCS
M0
SI
tsSI
M1
M2
DUMMY DATA(don't care)
M0
M1
thSI
SCLK
Mode selection
period
(3ck)
Data transfer period
(More than 13ck)
・M0：Mode flag: If M0 is "L" then display mode "Pixel data is held",
If M0 is "H" then Data refresh mode "Pixel data will be updated.
・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output.
If M1 is "L" then VCOM="L" is output.
In addition, if EXTMODE is set as "H", M1 set value doesn't matter.
・M2：All flags are cleared. If M2 is L then all flags are cleared.
When all clear are needed, refer to "all clear timing chart"
・DUMMY DATA： Dummy data. Don't care but "L" is recommended
※M1:
Frame inversion flag is enabled when EXTMODE=”L”.
※When SCS becomes L, M0 and M2 are cleared.
M2
DUMMY DATA(don't care)
14
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
15
LS013B4DN01
6-5-4 All Clear mode
Clear data in the pixel and the memory data and displays white color. (M0=”L”、M2＝”H”)
tV
twSCSH
twSCSL
SCS
thSCS
tsSCS
M0
SI
tsSI
M1
M2
DUMMY DATA(don't care)
M0
M1
thSI
SCLK
Mode selection
period
(3ck)
Data transfer period
(More than 13ck)
・M0：Mode flag: If M0 is "L" then display mode "Pixel data is held",
If M0 is "H" then Data refresh mode "Pixel data will be updated.
・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output.
If M1 is "L" then VCOM="L" is output.
In addition, if EXTMODE is set as "H", M1 set value doesn't matter.
・M2：All flags are cleared. If M2 is L then all flags are cleared.
When all clear are needed, refer to "all clear timing chart"
・DUMMY DATA： Dummy data. Don't care but "L" is recommended
※M1:
Frame inversion flag is enabled when EXTMODE=”L”.
※When SCS becomes L, M0 and M2 are cleared.
M2
DUMMY DATA(don't care)
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
16
6-5-5 COM Inversion
There are two signals, one is COM signal with serial Input(EXTMODE=”L”)
and other is external COM signal input (EXTMODE=”H”).
EXTMODE="L"
SCS
M0
SI
M1 M2
※1
M0
M1 M2
※1
M0
M1 M2
※1
COM
fCOM
※2
※2
・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output. If M1 is "L" then VCOM="L" is output.
※1：LC inversion has been changed by M1 flag statement.
※2：The periods of plus polarity and minus polarity should be same length as much as possible.
EXTMODE="H"
SCS
fEXTCOMIN
twEXTCOMIN
EXTCOMIN
COMZ
※1
※1
※1
COM
fCOM
※2
※2
※1：LC inversion polarity has been set by the rising timing of EXTCOMIN in internal circuit block as COMZ signal,
and when SCS become falling timing, LC inversion has been activated as COM signal.
※2：The period of EXTCOMIN should be constant.
Truth table of COM
＜EXTMODE="L"＞
COM
EXTCOMIN
反転前
L
L
H
H
＜EXTMODE="H"＞
反転後
反転前
Depend on
status of M1
EXTCOMIN
反転後
COMZ
反転前
COMZ
反転後
L
L
L
H
H
L
H
L
H
H
H
L
In rising timing of EXTMODE,
internal signal "COMZ" is inverted.
L
H
COM
SCS="L" SCS="H"
L
Qn-1
H
Qn-1
※Qn-1：COM has been changed polarity when SCS meet falling edge.
(COMZ status has been fixed by signal SCS)
SPEC
No.
MODEL
LCY-12T09302A
6-6）Input Signal and Display, Gate address(Line) Setting
Data position in display〔H,V〕
Up
P1,L1
P2,L1
P1,L2
P2,L2
P3,L1
P96, L1
P1,L3
Display
side up
P96,L96
P1,L96
ライン
Line
L1
L2
L3
・
・
・
L94
L95
L96
Gate
line address setting
ゲートラインアドレス設定
AG0
H
L
H
・
・
・
L
H
L
AG1
L
H
H
・
・
・
H
H
L
AG2
L
L
L
・
・
・
H
H
L
AG3
L
L
L
・
・
・
H
H
L
AG4
L
L
L
・
・
・
H
H
L
AG5
L
L
L
・
・
・
L
L
H
AG6
L
L
L
・
・
・
H
H
H
No.
LS013B4DN01
PAGE
17
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
18
LS013B4DN01
7．Optical characteristics
Table 7-1
Ta=25℃
Item
Viewing angle
CR≧5
Symbol
MAX.
unit
θ21,θ22
TBD
°(degree)
V
θ11
TBD
°(degree)
θ12
TBD
°(degree)
CR.
Reflecivity ratio
Panel
Chromaticity
TYP.
H
Contrast ratio
Response time
MIN.
5
Remark
[Remark7-1]
10
[Remark7-2､3]
R
50
%
[remark7-3]
Rise
τr
50
ms
[Remark 7-3,4]
Fall
τd
50
ms
White
x
0.313
y
0.338
[Remark7-3]
ٛ [Remark7-3] Optical characteristics measurement equipment.
Figure 7-2 is for contrast ratio, reflectivity ratio, and panel chromaticity measurement, and figure 7-3 is for response time
measurement. Both are to be conducted in a dark or room equipment to a dark room
Measurement equipment (LCD-5200)
Measurement equipment (CM-2002)
Normal line
Normal line
Light receiver
Light receiver
Light source
Light source
-30°
Integrating
sphere
LCD panel
LCD panel
Display center
Fig7-2 Contrast ratio, Reflection ratio, Panel chromaticity of white
Display center
Fig7-3 response time
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
[Remark7-1] Defintion of Viewint Angle
Normal
Δθ22
Δθ11
Δθ12
Δθ21
6 o’clock
[Remark7-2] Defintion of Contrast Retio
Reflection intensity in white display
Contrast ratio(CR) ＝
Reflection intensity in black display
[Remark7-4] Respons time (Change in reflection ratio)
It’s difined by the time change of optical receiver output when signal is input to display white or black
White
Black
White
100%
Photo detector output
90%
10%
0%
τｒ
Time
τｄ
19
SPEC
No.
MODEL
LCY-12T09302A
8．Module outline
1.35 Inch（96×96） Monochromatic zebra connector specifications
Fig8-1
Fig 8-2
No.
LS013B4DN01
external form drawing
PAGE
20
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
9. External capacitor
Fig.9-1 External capacitor recommendation capacity value
＜Recommended capacity value＞
C1：DISP- VSS: rank B
0.1uF Ceramic capacitor
C2：VDDA- VSS: rank B 1uF
C3：VDD- VSS: rank B
Ceramic capacitor
1uF Ceramic capacitor
[Remark] The recommedation capacity of an external capacitor is shown. Finally, determine a capacity value
after performing evaluation sufficient by your system.
(More bigger capacity value is selectable.)
21
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
22
LS013B4DN01
10. External Power Supply Circuit
10-1An external power supply circuit is necessary to drive the Pixel Memory LCD with the 3V battery.
Table 1-1 shows power supply IC of the recommendation.
Table 1-1
Maker
SII
National Semiconductor
Model Number
Note
S-8821
Charge pump type
LM2750
Charge pump type
Refer to specifications of each power supply IC for a detailed specification.
Set the constant value after it evaluating it sufficiently by an actual application when you use it.
10-2. Electrical specification
Table 2-1
Vin [V]
Vout
min
max
min
typ
max
Iout
[A]
S-8821
2.8
5.0
4.9
5.0
5.1
0.04
LM2750
2.7
5.6
4.8
5.0
5.2
0.04
Model Number
Refer to specifications of each power supply IC for a detailed specification.
Set the constant value after it evaluating it sufficiently by an actual application when you use it.
10-3. Reference circuit
The reference circuit is shown below.
S-8821
LM2750
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
11．Zebra connector
Contact Resistance ：lower than 20Ω
【Recommended zebra connector】
・ Please select one from these two types.
① Shin-Etsu Polymer: MS-G type
Recommended size L：27.7±0.25mm W：1.8±0.1mm H：2.3±0.1mm P：0.1mm
② Shin-Etsu Polymer: GB-U type
Recommended size L：27.3±0.6mm W：1.7±0.2mm H：2.3±0.2mm P：0.1mm
The zebra connector placement position
1．MS-G Specifications（A figure of reference）
Fig 11-1
2．GB-U Specifications（A figure of reference）
Fig11-2
23
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
24
LS013B4DN01
12. Packaging
12-1）Serial number .( ink-jet print)
Show an indication point in a figure of external form dimensions of fig 12-1.
Model number
Print structure
LS013B4DN01
Display
side up
9312AD00001FA
ABC
D
Serial number specifications
A：a single figure of the year
B：month(1,2....9,X,Y,Z)
C：day
D：serial numbeｒ
Fig 12-1
Serial number print position
Back
side up
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
LS013B4DN01
12-2）Forwarding form
①Piling number of cartons : Max 12
Package quality in a carton: 1,000pcs
②Conditions for storage.
・Temperature： 0～40℃
・Humidity： 60%RH or less (at 40℃) No dew condensation at low temperature and high humidity.
・Atmosphere：Harmful gas, such as acid or alkali which bites electronic
components and/or wires, must not be detected.
・Period
: about 3 months
・Opening of the package
: In order to prevent the LCD module from breakdown by electrostatic charge,
please control the room humidity over 50%RH and open the package taking
sufficient countermeasures against electrostatic charges, such as earth, etc.
12-3）Packaging
fig 12-2 Packege Form
25
SPEC
No.
MODEL
LCY-12T09302A
No.
PAGE
26
LS013B4DN01
13. Reliability Test Conditions
13-1 Reliability test items
Table13-1
Test Item
1
2
3
Test condition
High temperature storage test
Ta=80℃
240h
Low temperature storage test
Ta=35℃
240h
High temperature and high humidity
Tp=40℃/95%RH
240h
240h
Remark
operating test
4
High temperature operating test
Tp=70℃
5
Low temperature operating test
Tp=-20℃
6
Shock test
Ta=-30℃(1h)～+80℃(1h) / 5 cycle
7
Electro static discharge test
±200V、200pF(0Ω) each terminai: 1 time
240h
[Remark] Ta = Ambient temperature, Tp = Panel temperature
[Check items] In the standard condition, there shall be no practical problems that may affect the
display function.
13-2 Panel surface stress spesification
Panel surface stress spesification has been defined as a parameter “Force of stress [N]” without no picture failer.
Load testing： Minimum 120[N]
Test condition :
Test stracture
Press point
Press Jig
Press speed
Support
：LCD panel with UV protection film
：Center of LCD panel
：φ10mm column
：1mm／minute
：fixed on stage
Press time ：5 seconds after achievement of the press strength, then reless it.
Technical Document
LCD Specification
LCD Group
NORTH AMERICA
Sharp Microelectronics of the Americas
5700 NW Pacific Rim Blvd.
Camas, WA 98607, U.S.A.
Phone: (1) 360-834-8700
Fax: (1) 360-834-8903
www.sharpsma.com
TAIWAN
Sharp Electronic Components
(Taiwan) Corporation
8F-A, No. 16, Sec. 4, Nanking E. Rd.
Taipei, Taiwan, Republic of China
Phone: (886) 2-2577-7341
Fax: (886) 2-2577-7326/2-2577-7328
CHINA
Sharp Microelectronics of China
(Shanghai) Co., Ltd.
28 Xin Jin Qiao Road King Tower 16F
Pudong Shanghai, 201206 P.R. China
Phone: (86) 21-5854-7710/21-5834-6056
Fax: (86) 21-5854-4340/21-5834-6057
Head Office:
No. 360, Bashen Road,
Xin Development Bldg. 22
Waigaoqiao Free Trade Zone Shanghai
200131 P.R. China
Email: [email protected]
EUROPE
Sharp Microelectronics Europe
Division of Sharp Electronics (Europe) GmbH
Sonninstrasse 3
20097 Hamburg, Germany
Phone: 49 (0)180 507 35 07
Fax: (49) 40-2376-2232
www.sharpsme.com
JAPAN
Sharp Corporation
Electronic Components & Devices
22-22 Nagaike-cho, Abeno-Ku
Osaka 545-8522, Japan
Phone: (81) 6-6621-1221
Fax: (81) 6117-725300/6117-725301
www.sharp-world.com
SINGAPORE
Sharp Electronics (Singapore) PTE., Ltd.
438A, Alexandra Road, #05-01/02
Alexandra Technopark,
Singapore 119967
Phone: (65) 271-3566
Fax: (65) 271-3855
HONG KONG
Sharp-Roxy (Hong Kong) Ltd.
Level 26, Tower 1, Kowloon Commerce Centre,
No. 51, Kwai Cheong Road, Kwai Chung,
New Territories, Hong Kong
Phone: (852) 28229311
Fax: (852) 28660779
www.sharp.com.hk
Shenzhen Representative Office:
Room 602-603, 6/F.,
International Chamber of Commerce Tower,
168 Fuhua Rd. 3, CBD,
Futian District, Shenzhen 518048,
Guangdong, P.R. China
Phone: (86) 755-88313505
Fax: (86) 755-88313515
KOREA
Sharp Electronic Components
(Korea) Corporation
RM 501 Geosung B/D, 541
Dohwa-dong, Mapo-ku
Seoul 121-701, Korea
Phone: (82) 2-711-5813 ~ 8
Fax: (82) 2-711-5819
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for
limitations on special applications. See Limited Warranty for SHARP’s product warranty.
The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE,
ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in
any way, for any incidental or consequential economic or property damage.