MX23L1610 3.3 Volt 16-Mbit (2M x 8 / 1M x 16) Mask ROM ORDER INFORMATION FEATURES • Bit organization - 2M x 8 (byte mode) - 1M x 16 (word mode) • Fast access time - 105ns (max.)@3.3V±10% - 100ns (max.)@3.3V±5% • Current - Operating:25mA - Standby:15uA • Supply voltage - 3.0V ~ 3.6V • Package - 44 pin SOP (500mil) - 42 pin DIP (600mil) - 48 pin TSOP (20mm x 12mm) Package MX23L1610MC-10 100ns 44 pin SOP MX23L1610MC-11 105ns 44 pin SOP MX23L1610MC-12 120ns 44 pin SOP MX23L1610MC-15 150ns 44 pin SOP MX23L1610PC-10 100ns 42 pin PDIP MX23L1610PC-11 105ns 42 pin PDIP MX23L1610PC-12 120ns 42 pin PDIP MX23L1610PC-15 150ns 42 pin PDIP MX23L1610TC-10 100ns 48 pin TSOP MX23L1610TC-11 105ns 48 pin TSOP MX23L1610TC-12 120ns 48 pin TSOP MX23L1610TC-15 150ns 48 pin TSOP MX23L1610RC-10 100ns 48 pin TSOP MX23L1610RC-11 105ns 48 pin TSOP 42 PDIP 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 NC A19 A8 A9 A10 A11 A12 A13 A14 A15 A16 BYTE VSS D15/A-1 D7 D14 D6 D13 D5 D12 D4 VCC A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE VSS OE D0 D8 D1 D9 D2 D10 D3 D11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 (Reverse type) MX23L1610 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 MX23L1610 NC A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE VSS OE D0 D8 D1 D9 D2 D10 D3 D11 Access (Reverse type) PIN CONFIGURATION 44 SOP Part No. 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 A19 A8 A9 A10 A11 A12 A13 A14 A15 A16 BYTE VSS D15/A-1 D7 D14 D6 D13 D5 D12 D4 VCC MX23L1610RC-12 120ns 48 pin TSOP MX23L1610RC-15 150ns 48 pin TSOP (Reverse type) (Reverse type) MX23L1610TI-12* 48 pin TSOP *Note:Temperature: -40~85°C PIN DESCRIPTION Symbol A0~A19 D0~D14 D15/A-1 CE OE Byte VCC VSS NC P/N:PM0243 Pin Function Address Inputs Data Outputs D15 (Word Mode)/ LSB Address (Byte Mode) Chip Enable Input Output Enable Input Word/ Byte Mode Selection Power Supply Pin Ground Pin No Connection REV. 2.1, JAN. 18, 2000 1 This Material Copyrighted by Its Respective Manufacturer 120ns MX23L1610 48 TSOP (Normal Type) BYTE A16 A15 A14 A13 A12 A11 A10 A9 A8 A19 VSS NC A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 TSOP (Reverse Type) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 MX23L1610 (Normal Type) VSS VSS D15/A-1 D7 D14 D6 D13 D5 D12 D4 VCC VCC NC D11 D3 D10 D2 D9 D1 D8 D0 OE VSS VSS VSS VSS D15/A-1 D7 D14 D6 D13 D5 D12 D4 VCC VCC NC D11 D3 D10 D2 D9 D1 D8 D0 OE VSS VSS 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 MX23L1610 (Reverse Type) BYTE A16 A15 A14 A13 A12 A11 A10 A9 A8 A19 A21 A20 A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE MODE SELECTION CE OE Byte D15/A-1 D0~D7 D8~D15 Mode Power H X X X High Z High Z - Stand-by L H X X High Z High Z - Active L L H Output D0~D7 D8~D15 Word Active L L L Input D0~D7 High Z Byte Active Word/ Byte Output Buffer BLOCK DIAGRAM A0/(A-1) A19 Address Buffer Memory Array Page Decoder Page Buffer D0 D15/(D7) CE BYTE OE P/N:PM0243 REV. 2.1, JAN. 18, 2000 2 This Material Copyrighted by Its Respective Manufacturer MX23L1610 ABSOLUTE MAXIMUM RATINGS Item Voltage on any Pin Relative to VSS Ambient Operating Temperature Storage Temperature Symbol VIN Topr Tstg Ratings -0.3V to 4.3V 0°C to 70°C -65°C to 125°C Note: Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, inputs may undershoot VSS to -1.3V for periods of up to 20ns. Maximum DC voltage on input or I/O pins is VCC+0.5V. During voltage transitions, input may overshoot VCC to VCC+2.0V for periods of up to 20ns. DC CHARACTERISTICS (Ta = 0°C ~ 70°C, VCC = 3.0V~3.6V) Item Output High Voltage Output Low Voltage Input High Voltage Symbol VOH VOL VIH MIN. 2.3V 2.1V MAX. 0.4V VCC+0.3V* Input Low Voltage Input Leakage Current Output Leakage Current Operating Current Standby Current (TTL) Standby Current (cmos) Input Capacitance Output Capacitance VIL ILI ILO ICC1 ISTB1 ISTB2 CIN COUT -0.3V - 0.2 x VCC 5uA 5uA 25mA 0.5mA 15uA 10pF 10pF P/N:PM0243 0V, VCC 0V, VCC tRC = 120ns, all output open CE = VIH CE>VCC-0.2V Ta = 25°C, f = 1MHZ Ta = 25°C, f = 1MHZ REV. 2.1, JAN. 18, 2000 3 This Material Copyrighted by Its Respective Manufacturer Conditions IOH = -400uA IOL = 1.6mA MAX. number:VCC+0.3V is under normal operation mode, and VCC+0.7V is under non-operating mode MX23L1610 AC CHARACTERISTICS (Ta = 0°C ~ 70°C, VCC = 3.0V~3.6V) Item Symbol 23L1610-10 23L1610-11 23L1610-12 23L1610-15 Read Cycle Time tRC MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. 100ns - 105ns - 120ns - 150ns - Address Access Time tAA - 100ns - 105ns - 120ns - 150ns Chip Enable Access Time tACE - 100ns - 105ns - 120ns - 150ns Output Enable Time tOE - 50ns - 55ns - 60ns - 70ns Output Hold After Address tOH 0ns - 0ns - 0ns - 0ns - Output High Z Delay tHZ - 20ns - 20ns - 20ns - 20ns Note:Output high-impedance delay (tHZ) is measured from OE or CE going high, and this parameter guaranteed by design over the full voltage and temperature operating range - not tested. AC Test Conditions Input Pulse Levels Input Rise and Fall Times Input Timing Level Output Timing Level Output Load 0.4V~ 2.4V 10ns 1.4V 1.4V See Figure IOH (load)=-0.4mA DOUT IOL (load)=1.6mA C<100pF Note:No output loading is present in tester load board. Active loading is used and under software programming control. TIMING DIAGRAM Output loading capacitance includes load board's and all stray capacitance. RANDOM READ ADD ADD ADD ADD tRC tACE CE OE tOE tAA DATA tOH VALID VALID tHZ VALID Note: CE, OE are enable. P/N:PM0243 REV. 2.1, JAN. 18, 2000 4 This Material Copyrighted by Its Respective Manufacturer MX23L1610 PACKAGE INFORMATION 42-PIN PLASTIC DIP(600 mil) ITEM MILLIMETERS INCHES A 52.54 max. 2.070 max. B 0.76 [REF] .030 [REF] C 2.54 [TP] .100 [TP] D .46 [Typ.] .018 [Typ.] E 50.76 2.000 F 1.27 [Typ.] .050 [Typ.] G 3.30 ± . 25 .130 ± .010 H .51 [REF] .020 [REF] I 3.94 ±. 25 .155 ± .010 J 5.33 max. .210 max. K 15.22 ± .25 .600 ± .010 L 13.97± .25 .550 ± .010 .25 [Typ.] .010 [Typ.] M NOTE: 42 22 21 1 A K L I H F D Each lead centerline is located within .25 mm[.01 inch] of its true position [TP] at maximum material condition. C J G B 0~15¡ M E 44-PIN PLASTIC SOP ITEM MILLIMETERS INCHES A 28.70 max. 1.130 max. B 1.10 [REF] .043 [REF] C 1.27 [TP] .050 [TP] D .40 ± .10 [Typ.] .016 ± .004 [Typ.] E .010 min. .004 min. F 3.00 max. .118 max. G 2.80 ± .13 .110 ± .005 H 16.04 ± .30 .631 ± .012 I 12.60 .496 J 1.72 .068 K .15 ± .10 [Typ.] .006 ± .004 [Typ.] L .80 ± .20 .031 ± .008 44 23 1 22 H A I G J F K E D C B L NOTE: Each lead centerline is located within .25 mm[.01 inch] of its true position [TP] at maximum material condition. P/N:PM0243 REV. 2.1, JAN. 18, 2000 5 This Material Copyrighted by Its Respective Manufacturer MX23L1610 PACKAGE INFORMATION 48-PIN PLASTIC TSOP ITEM MILLIMETERS INCHES A 20.0 ± .20 .787 ± .008 B 18.40 ± .10 .724 ± .004 C 12.20 max. .480 max. D 0.15 [Typ.] .006 [Typ.] E .80 [Typ.] .031 [Typ.] F .20 ± .10 .008 ±.004 G .30 ± .10 .012 ± .004 H .50 [Typ.] .020 [Typ.] I .45 max. .018 max. J 0 ~ .20 0 ~ .008 K 1.00 ± .10 .039 ± .004 L 1.27 max. .050 max. M .50 .020 0 ~ 5° .500 A N NOTE: B C N M K L D E F G H I J Each lead centerline is located within .25 mm[.01 inch] of its true position [TP] at maximum material condition. P/N:PM0243 REV. 2.1, JAN. 18, 2000 6 This Material Copyrighted by Its Respective Manufacturer MX23L1610 REVISION HISTORY REVISION 1.9 2.0 2.1 DESCRIPTION 1. Package Type:Add 42-PDIP package type. 2. DC Characteristics:The input low voltage VIL Max. value is changed as 0.2xVCC instead of 0.8V. 3. AC Characteristics:The output high Z delay is changed as 20ns instead of 70ns. 4. Add 105ns speed grade. 5. Add 100ns speed grade @3.3V±5% 6. AC Test Conditions:The output timing level is changed as 1.4V instead of 0.8V and 2.0V. AC CHARACTERISTICS tOH 10ns-->0ns Typing error correction P/N:PM0243 DATE JUN/11/1998 P4 P1 FEB/01/1999 JAN/18/2000 REV. 2.1, JAN. 18, 2000 7 This Material Copyrighted by Its Respective Manufacturer PAGE MX23L1610 MACRONIX INTERNATIONAL CO., LTD. HEADQUARTERS: TEL:+886-3-578-6688 FAX:+886-3-563-2888 EUROPE OFFICE: TEL:+32-2-456-8020 FAX:+32-2-456-8021 JAPAN OFFICE: TEL:+81-44-246-9100 FAX:+81-44-246-9105 SINGAPORE OFFICE: TEL:+65-348-8385 FAX:+65-348-8096 TAIPEI OFFICE: TEL:+886-2-509-3300 FAX:+886-2-509-2200 MACRONIX AMERICA, INC. TEL:+1-408-453-8088 FAX:+1-408-453-8488 CHICAGO OFFICE: TEL:+1-847-963-1900 FAX:+1-847-963-1909 http : //www.macronix.com MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 8 This Material Copyrighted by Its Respective Manufacturer