HYMD116G7258-H/L 16Mx72 Registered DDR SDRAM DIMM PRELIMINARY DESCRIPTION Hynix HYMD116G7258-H/L series is registered 184-pin double data rate Synchronous DRAM Dual In-Line Memory Modules (DIMMs) which are organized as 16Mx72 high-speed memory arrays. Hynix HYMD116G7258-H/L series consists of nine 16Mx8 DDR SDRAM in 400mil TSOP II packages on a 184pin glass-epoxy substrate. Hynix HYMD116G7258-H/L series provide a high performance 8-byte interface in 5.25" width form factor of industry standard. It is suitable for easy interchange and addition. Hynix HYMD116G7258-H/L series is designed for high speed of up to 133MHz and offers fully synchronous operations referenced to both rising and falling edges of differential clock inputs. While all addresses and control inputs are latched on the rising edges of the clock, Data, Data strobes and Write data masks inputs are sampled on both rising and falling edges of it. The data paths are internally pipelined and 2-bit prefetched to achieve very high bandwidth. All input and output voltage levels are compatible with SSTL_2. High speed frequencies, programmable latencies and burst lengths allow variety of device operation in high performance memory system. Hynix HYMD116G7258-H/L series incorporates SPD(serial presence detect). Serial presence detect function is implemented via a serial 2,048-bit EEPROM. The first 128 bytes of serial PD data are programmed by Hynix to identify DIMM type, capacity and other the information of DIMM and the last 128 bytes are available to the customer. FEATURES • 128MB (16M x 72) Registered DDR DIMM based on 16Mx8 DDR SDRAM • JEDEC Standard 184-pin dual in-line memory module (DIMM) • Error Check Correction (ECC) Capability • Registered inputs with one-clock delay • Phase-lock loop (PLL) clock driver to reduce loading • 2.5V +/- 0.2V VDD and VDDQ Power supply • All inputs and outputs are compatible with SSTL_2 interface • Fully differential clock operations (CK & /CK) with 100MHz/125MHz/133MHz • Programmable CAS Latency 2 / 2.5 supported • Programmable Burst Length 2 / 4 / 8 with both sequential and interleave mode • Internal four bank operations with single pulsed RAS • Auto refresh and self refresh supported • 4096 refresh cycles / 64ms ORDERING INFORMATION Part No. Power Suppy Clock Frequency HYMD116G7258-H VDD=2.5V VDDQ=2.5V 133MHz (*DDR266B) HYMD116G7258-L 100MHz (*DDR200) Interface Form Factor SSTL_2 184pin Registered DIMM 5.25 x 1.25 x 0.15 inch * JEDEC Defined Specifications compliant This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev.1.3/Apr.01 HYMD116G7258-H/L PIN DESCRIPTION Pin Pin Description Pin Pin Description CK0, /CK1 Differential Clock Inputs VDDQ DQs Power Supply /CS0 Chip Select Input VSS Ground CKE0 Clock Enable Input VREF Reference Power Supply /RAS, /CAS, /WE Commend Sets Inputs VDDSPD Power Supply for SPD A0 ~ A11 Address SA0~SA2 E2PROM Address Inputs BA0, BA1 Bank Address SCL E2PROM Clock DQ0~DQ63 Data Inputs/Outputs SDA E2PROM Data I/O CB0~CB7 Data Strobe Inputs/Outputs WP Write Protect Flag DQS0~DQS8 Data Strobe Inputs/Outputs VDDID VDD Identification Flag DM0~8 Data-in Mask DU Do not Use VDD Power Supply NC No Connection /RESET Reset Enable FETEN FET Enable PIN ASSIGNMENT Pin Name Pin Name Pin Name Pin Name Pin Name Pin 1 VREF 32 A5 62 VDDQ 93 VSS 124 VSS 154 Name /RAS 2 DQ0 33 DQ24 63 /WE 94 DQ4 125 A6 155 DQ45 3 VSS 34 VSS 64 DQ41 95 DQ5 126 DQ28 156 VDDQ 4 DQ1 35 DQ25 65 /CAS 96 VDDQ 127 DQ29 157 /CS0 5 DQS0 36 DQS3 66 VSS 97 DM0 128 VDDQ 158 /CS1* 6 DQ2 37 A4 67 DQS5 98 DQ6 129 DM3 159 DM5 7 VDD 38 VDD 68 DQ42 99 DQ7 130 A3 160 VSS 8 DQ3 39 DQ26 69 DQ43 100 VSS 131 DQ30 161 DQ46 DQ47 9 NC 40 DQ27 70 VDD 101 NC 132 VSS 162 10 /RESET 41 A2 71 NC 102 NC 133 DQ31 163 NC 11 VSS 42 Vss 72 DQ48 103 A13* 134 CB4 164 VDDQ 12 DQ8 43 A1 73 DQ49 104 VDDQ 135 CB5 165 DQ52 13 DQ9 44 CB0 74 VSS 105 DQ12 136 VDDQ 166 DQ53 NC, FETEN* 14 DQS1 45 CB1 75 DU 106 DQ13 137 CK0 167 15 VDDQ 46 VDD 76 DU 107 DM1 138 /CK0 168 VDD 16 DU 47 DQS8 77 VDDQ 108 VDD 139 VSS 169 DM6 17 DU 48 A0 78 DQS6 109 DQ14 140 DM8 170 DQ54 18 VSS 49 CB2 79 DQ50 110 DQ15 141 A10 171 DQ55 19 DQ10 50 VSS 80 DQ51 111 CKE1* 142 CB6 172 VDDQ 20 DQ11 51 CB3 81 VSS 112 VDDQ 143 VDDQ 173 NC 21 CKE0 52 BA1 82 VDDID 113 BA2* 144 CB7 174 DQ60 22 VDDQ 83 DQ56 114 DQ20 175 DQ61 23 DQ16 53 DQ32 84 DQ57 115 A12* 145 VSS 176 VSS 24 DQ17 54 VDDQ 85 VDD 116 VSS 146 DQ36 177 DM7 25 DQS2 55 DQ33 86 DQS7 117 DQ21 147 DQ37 178 DQ62 26 VSS 56 DQS4 87 DQ58 118 A11 148 VDD 179 DQ63 27 A9 57 DQ34 88 DQ59 119 DM2 149 DM4 180 VDDQ 28 DQ18 58 VSS 89 VSS 120 VDD 150 DQ38 181 SA0 29 A7 59 BA0 90 WP 121 DQ22 151 DQ39 182 SA1 30 VDDQ 60 DQ35 91 SDA 122 A8 152 VSS 183 SA2 31 DQ19 61 DQ40 92 SCL 123 DQ23 153 DQ44 184 VDDSPD Key key * These are not used on this module but may be used for other module in 184pin DIMM family Rev.1.3/Apr.01 2 HYMD116G7258-H/L FUNCTIONAL BLOCK DIAGRAM . /RCS0 DQS0 DM0 DQS4 DM4 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 /CS DQS D0 DQS1 DM1 DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DM I/O I/O I/O I/O I/O I/O I/O I/O 0 1 2 3 4 5 6 7 DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 DM I/O I/O I/O I/O I/O I/O I/O I/O 0 1 2 3 4 5 6 7 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DM I/O I/O I/O I/O I/O I/O I/O I/O 0 1 2 3 4 5 6 7 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DM I/O I/O I/O I/O I/O I/O I/O I/O /CS 0 1 2 3 4 5 6 7 DQS D1 DQS2 DM2 /CS DM I/O I/O I/O I/O I/O I/O I/O I/O /CS 0 1 2 3 4 5 6 7 DQS D2 DQS3 DM3 D5 /CS DQS D6 DQS7 DM7 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CB0 CB1 CB2 CB3 CB4 CB5 CB6 CB7 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /CS DQS D3 DQS8 DM8 /CS DQS D7 Serial PD /CS DQS D8 SCL WP 47 K VDDSPD VDDQ VDD VREF VSS R E G /RCS0 -->/CS : SDRAMs D0-D8 RBA0-RBA1 -->BA0-BA1 : SDRAMs D0 - D8 RA0 -R A11 -->A0 - A11 : SDRAMs D0 - D8 /RRAS --> /RAS : SDRAMs D0 - D8 /RCAS --> /CAS : SDRAMs D0 - D8 RCKE0 --> CKE : SDRAMs D0 - D8 /RWE --> /WE : SDRAMs D0 - D8 /RESET /PCK CK0, /CK0 --------- PLL* * Wire per clock loading table/wiring diagrams Rev.1.3/Apr.01 DQS DQS6 DM6 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 PCK D4 DQS5 DM5 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 /CS0 BA0-BA1 A0-A11 /RAS /CAS CKE0 /WE DQS VDDID A0 A1 A2 SA0 SA1 SA2 . .= . . . . . =. . .. = = SDA SPD D0 - D8 D0 - D8 D0 - D8 D0 - D8 Strap:see Note 4 Notes: 1. DQ-to-I/O wiring may be changed within a byte 2. DQ/DQS/DM/CKE/CS relationships must be maintained as shown. 3. DQ/DQS resistors should be 22 Ohms. 4. VDDID strap connections(for memory device VDD, VDDQ); Strap out :(open) : VDD=VDDQ Strap In (Vss) : VDD=VDDQ 5. SDRAM placement alternates btw the back and front sides for the DIMM 6. Address and control resistors should be 22 Ohms 3 HYMD116G7258-H/L ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Ambient Temperature TA 0 ~ 70 o C Storage Temperature TSTG -55 ~ 125 o C VIN, VOUT -0.5 ~ 3.6 V VDD -0.5 ~ 3.6 V VDDQ -0.5 ~ 3.6 V Output Short Circuit Current IOS 50 mA Power Dissipation PD 9 W TSOLDER 260 / 10 Voltage on Any Pin relative to VSS Voltage on V DD relative to VSS Voltage on V DDQ relative to VSS Soldering Temperature / Time Unit o C / Sec Note : Operation at above absolute maximum rating can adversely affect device reliability DC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS=0V) Parameter Symbol Min Typ. Max Unit Power Supply Voltage VDD 2.3 2.5 2.7 V Power Supply Voltage VDDQ 2.3 2.5 2.7 V Input High Voltage VIH VREF + 0.15 - VDDQ + 0.3 V Input Low Voltage VIL -0.3 - VREF - 0.15 V Termination Voltage VTT VREF - 0.04 VREF VREF + 0.04 V Reference Voltage VREF 0.49*VDDQ 0.5*VDDQ 0.51*VDDQ V Note 1 2 3 Note : 1. V DDQ must not exceed the level of VDD. 2. V IL (min) is acceptable -1.5V AC pulse width with < 5ns of duration. 3. The value of VREF is approximately equal to 0.5VDDQ. AC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS=0V) Parameter Symbol Min Input High (Logic 1) Voltage, DQ, DQS and DM signals VIH(AC) VREF + 0.31 Input Low (Logic 0) Voltage, DQ, DQS and DM signals VIL(AC) Input Differential Voltage, CK and /CK inputs VID(AC) Input Crossing Point Voltage, CK and /CK inputs VIX(AC) Max Unit Note V VREF - 0.31 V 0.7 VDDQ + 0.6 V 1 0.5*V DDQ-0.2 0.5*VDDQ+0.2 V 2 Note : 1. VID is the magnitude of the difference between the input level on CK and the input on /CK. 2. The value of VIX is expected to equal 0.5*V DDQ of the transmitting device and must track variations in the DC level of the same. Rev.1.3/Apr.01 4 HYMD116G7258-H/L AC OPERATING TEST CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS=0V) Parameter Value Unit Reference Voltage VDDQ x 0.5 V Termination Voltage VDDQ x 0.5 V AC Input High Level Voltage (VIH, min) VREF + 0.31 V AC Input Low Level Voltage (VIL, max) VREF - 0.31 V Input Timing Measurement Reference Level Voltage VREF V Output Timing Measurement Reference Level Voltage VTT V Input Signal maximum peak swing 1.5 V Input minimum Signal Slew Rate 1 V/ns Termination Resistor (RT) 50 Ω Series Resistor (RS) 25 Ω Output Load Capacitance for Access Time Measurement (CL) 30 pF Rev.1.3/Apr.01 5 HYMD116G7258-H/L CAPACITANCE (TA=25oC, f=100MHz ) Parameter Pin Symbol Min Max Unit Input Capacitance A0 ~ A11, BA0, BA1 CIN1 5 12 pF Input Capacitance RAS, CAS, WE CIN2 5 12 pF Input Capacitance CKE0 CIN3 5 12 pF Input Capacitance CS0 CIN4 5 12 pF Input Capacitance CK0, CK0 CIN5 5 12 pF Input Capacitance DM0 ~ DM8 CIN6 10 13 pF Data Input / Output Capacitance DQ0 ~ DQ63, DQS0 ~ DQS8 CIO1 10 13 pF Data Input / Output Capacitance CB0 ~ CB7 CIO2 10 13 pF Note : 1. VDD=min. to max., VDDQ=2.3V to 2.7V, VODC=VDDQ/2, VOpeak-to-peak=0.2V 2. Pins not under test are tied to GND. 3. These values are guaranteed by design and are tested on a sample basis only. OUTPUT LOAD CIRCUIT VTT VTT RT=50Ω R T=50Ω Output RS=25Ω Zo=50Ω VREF CL=30pF Rev.1.3/Apr.01 6 HYMD116G7258-H/L DC CHARACTERISTICS I (TA=0 to 70oC, Voltage referenced to VSS = 0V) Parameter Symbol Min. Max Unit Note Input Leakage Current ILI -5 5 uA 1 Output Leakage Current ILO -5 5 uA 2 Output High Voltage VOH VTT + 0.76 - V IOH = -15.2mA Output Low Voltage VOL - VTT - 0.76 V IOL = +15.2mA Note : 1. VIN=0 to 3.6V, All other pins are not tested under VIN=0V 2. DOUT is disabled, VOUT=0 to 2.7V 3. These values are device characteristics. DC CHARACTERISTICS II (TA=0 to 70oC, Voltage referenced to VSS=0V) Parameter Symbol Test Condition Operating Current Speed Unit -H -L IDD0 One bank; Active - Precharge; tRC=tRC(min); tCK=tCK(min); DQ,DM and DQS inputs changing twice per clock cycle; address and control inputs changing once per clock cycle TBD TBD mA Operating Current IDD1 One bank; Active - Read - Precharge; Burst Length=2; tRC=tRC(min); tCK=tCK(min); address and control inputs changing once per clock cycle 1260 1170 mA Precharge Power Down Standby Current IDD2P All banks idle; Power down mode; CKE=Low, tCK=tCK(min) Idle Standby Current IDD2F CS=High, All banks idle; tCK=tCK(min); CKE=High; address and control inputs changing once per clock cycle. VIN=VREF for DQ, DQS and DM Active Power Down Standby Current IDD3P One bank active; Power down mode; CKE=Low, tCK=tCK(min) 225 mA IDD3N /CS=HIGH; CKE=HIGH; One bank; Active-Precharge; tRC=tRAS(max); tCK=t CK(min); DQ, DM, and DQS inputs changing twice per clock cycle; Address and other control inputs changing once per clock cycle 450 mA Active Standby Current Rev.1.3/Apr.01 180 320 Note mA 280 mA 7 HYMD116G7258-H/L DC CHARACTERISTICS II (TA=0 to 70oC, Voltage referenced to VSS = 0V) Parameter Operating Current Operating Current Symbol Test Condition IDD4R IDD4W Speed -H -L Burst=2; Reads; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK=tCK(min); IOUT=0mA TBD TBD Burst=2; Writes; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK=tCK(min); DQ, DM, and DQS inputs changing twice per clock cycle TBD TBD Auto Refresh Current IDD5 tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz, 10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh Self Refresh Current IDD6 CKE=<0.2V; External clock on; tCK=tCK(min) Operating Current - Four Bank Operation IDD7 Four bank interleaving with BL=4, Refer to the following page for detailed test condition Rev.1.3/Apr.01 - Continued- Unit Note mA 2880 Normal 18 mA Low Power 9 mA TBD mA 8 HYMD116G7258-H/L AC CHARACTERISTICS (AC operating conditions unless otherwise noted) Parameter Symbol -H(DDR266B) -L(DDR200) Min Max Min Max Unit Row Cycle Time tRC 65 - 70 - ns Auto Refresh Row Cycle Time tRFC 75 - 80 - ns Row Active Time tRAS 48 120K 50 120K ns Active to Read with Auto Precharge Delay tRAP tRASBL/2 x t CK - tRASBL/2 x tCK - ns Row Address to Column Address Delay tRCD 20 - 20 - ns Row Active to Row Active Delay tRRD 15 - 15 - ns Column Address to Column Address Delay tCCD 1 - 1 - CK tRP 20 - 20 - ns Last Data-In to Precharge Delay Time (Write Recovery Time) tDPL 15 - 20 - ns Last Data-In to Read Command tDRL 1 - 1 - CK Auto Precharge Write Recovery + Precharge Time tDAL 5 - 4 - CK 7.5 15 10 15 ns 10 15 10 15 ns Row Precharge Time System Clock Cycle Time CL = 2.5 CL = 2 tCK Note 16 15 Clock High Level Width tCH 0.45 0.55 0.45 0.55 CK Clock Low Level Width tCL 0.45 0.55 0.45 0.55 CK Data-Out edge to Clock edge Skew tAC -0.75 0.75 -0.8 0.8 ns DQS-Out edge to Clock edge Skew tDQSCK -0.75 0.75 -0.8 0.8 ns DQS-Out edge to Data-Out edge Skew tDQSQ - 0.5 - 0.6 ns Data-Out hold time from DQS tQH tHPmin -t QHS - tHPmin -t QHS - ns 1, 10 Clock Half Period tHP tCH/L min - tCH/L min - ns 1,9 Data Hold Skew Factor tQHS - 0.75 - 1 ns 10 Valid Data Output Window tDV Data-out high-impedance window from CK, /CK tHZ -1.2 0.8 ns Data-out low-impedance window from CK, /CK tLZ -1.2 0.8 ns Input Setup Time (fast slew rate) tIS 0.9 - 1.2 - ns 2,3,5,6 Input Hold Time (fast slew rate) tIH 0.9 - 1.2 - ns 2,3,5,6 Input Setup Time (slow slew rate) tIS 1.0 - 1.2 - ns 2,4,5,6 Input Hold Time (slow slew rate) tIH 1.0 - 1.2 - ns 2,4,5,6 tIPW 2.2 ns 6 tDQSH 0.35 Input Pulse Width Write DQS High Level Width Rev.1.3/Apr.01 tQH-t DQSQ tQH-tDQSQ ns - 0.35 - CK 9 HYMD116G7258-H/L AC CHARACTERISTICS (AC operating conditions unless otherwise noted) Parameter Symbol - continued - -H(DDR266B) -L(DDR200) Min Max Min Max Unit Note Write DQS Low Level Width tDQSL 0.35 - 0.35 - CK Clock to First Rising edge of DQS-In tDQSS 0.75 1.25 0.75 1.25 CK Data-In Setup Time to DQS-In (DQ & DM) tDS 0.5 - 0.6 - ns 6,7, 11~13 Data-in Hold Time to DQS-In (DQ & DM) tDH 0.5 - 0.6 - ns 6,7, 11~13 DQ & DM Input Pulse Width tDIPW 1.75 - 2 - ns Read DQS Preamble Time tRPRE 0.9 1.1 0.9 1.1 CK Read DQS Postamble Time tRPST 0.4 0.6 0.4 0.6 CK Write DQS Preamble Setup Time tWPRES 0 - 0 - CK Write DQS Preamble Hold Time tWPREH 0.25 - 0.25 - CK Write DQS Postamble Time tWPST 0.4 0.6 0.4 0.6 CK Mode Register Set Delay tMRD 2 - 2 - CK Exit Self Refresh to Any Execute Command tXSC 200 - 200 - CK Average Periodic Refresh Interval tREFI - 15.6 - 15.6 us 8 Note : 1. This calculation accounts for tDQSQ(max), the pulse width distortion of on-chip circuit and jitter. 2. Data sampled at the rising edges of the clock : A0~A11, BA0~BA1, CKE, CS, RAS, CAS, WE. 3. For command/address input slew rate >=1.0V/ns 4. For command/address input slew rate >=0.5V/ns and <1.0V/ns This derating table is used to increase tIS/tIH in case where the input slew-rate is below 0.5V/ns. Input Setup / Hold Slew-rate Derating Table. Input Setup / Hold Slew-rate Delta tIS Delta tIH V/ns ps ps 0.5 0 0 0.4 +50 0 0.3 +100 0 5. CK, /CK slew rates are >=1.0V/ns 6. These parameters guarantee device timing, but they are not necessarily tested on each device, and they may be guaranteed by design or tester correlation. 7. Data latched at both rising and falling edges of Data Strobes(LDQS/UDQS) : DQ, LDM/UDM. 8. Minimum of 200 cycles of stable input clocks after Self Refresh Exit command, where CKE is held high, is required to complete Self Refresh Exit and lock the internal DLL circuit of DDR SDRAM. 9. Min(tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for tCL and tCH). 10. tHP = minimum half clock period for any given cycle and is defined by clock high or clock low(tCH, tCL). tQHS consists of tDQSQmax, the pulse width distortion of on-chip clock circuits, data pin to pin skew and output pattern effects and p-channel to n-channel variation of the output drivers. Rev.1.3/Apr.01 10 HYMD116G7258-H/L 11.This derating table is used to increase tDS/tDH in case where the input slew-rate is below 0.5V/ns. Input Setup / Hold Slew-rate Derating Table. Input Setup / Hold Slew-rate Delta tDS Delta tDH V/ns ps ps 0.5 0 0 0.4 +75 +75 0.3 +150 +150 12. I/O Setup/Hold Plateau Derating. This derating table is used to increase tDS/tDH in case where the input level is flat below VREF +/-310mV for a duration of up to 2ns. I/O Input Level Delta tDS Delta tDH mV ps ps +280 +50 +50 13. I/O Setup/Hold Delta Inverse Slew Rate Derating. This derating table is used to increase tDS/tDH in case where the DQ and DQS slew rates differ. The Delta Inverse Slew Rate is calculated as (1/SlewRate1)-(1/SlewRate2). For example, if slew rate1=0.5V/ns and Slew Rate2=0.4V/n then the Delta Inverse Slew Rate=-0.5ns/V. (1/SlewRate1)-(1/SlewRate2) Delta tDS Delta tDH ns/V ps ps 0 0 0 +/-0.25 +50 +50 +/- 0.5 +100 +100 14. DQS, DM and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transi tions through the DC region must be monotonic. 15. tDAL=(tDPL / tCK ) + (tRP / tCK ). For each of the terms above, if not already an integer, round to the next highest integer. tCK is equal to the actual system clock cycle time. Example: For DDR266B at CL=2.5 and tCK = 7.5 ns, tDAL=(15 ns / 7.5 ns) + (20 ns / 7.5 ns)=(2.00) + (2.67) Round up each non-integer to the next highest integer: = (2) + (3), tDAL = 5 clocks 16. For the parts which do not has internal RAS lockout circuit, Active to Read with Auto precharge delay should be tRAS BL/2 x tCK. Rev.1.3/Apr.01 11 HYMD116G7258-H/L SIMPLIFIED COMMAND TRUTH TABLE A10/ AP Command CKEn-1 CKEn CS RAS CAS WE Extended Mode Register Set H X L L L L OP code 1,2 Mode Register Set H X L L L L OP code 1,2 H X H X X X L H H H X 1 H X L L H H H X L H L H CA H X L H L L CA H X L L H L X Read Burst Stop H X L H H L X 1 Auto Refresh H H L L L H X 1 Entry H L L L L H Exit L H H X X X L H H H Entry H L H X X X L H H H H X X X L H H H 1 H X X X 1 L V V V Device Deselect No Operation Bank Active Read Read with Autoprecharge Write Write with Autoprecharge Precharge All Banks Precharge selected Bank Self Refresh Precharge Power Down Mode Active Power Down Mode Exit L H Entry H L Exit L H X ADDR RA BA V L H L H V V Note 1 1 1,3 1 1,4 H X 1,5 L V 1 1 X 1 1 X X 1 1 1 1 ( H=Logic High Level, L=Logic Low Level, X=Don’t Care, V=Valid Data Input, OP Code=Operand Code, NOP=No Operation ) Note : 1. DM states are Don’t Care. Refer to below Write Mask Truth Table. 2. OP Code(Operand Code) consists of A0~A 11 and BA0~BA1 used for Mode Registering duing Extended MRS or MRS. Before entering Mode Register Set mode, all banks must be in a precharge state and MRS command can be issued after tRP period from Prechagre command. 3. If a Read with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented to activated bank until CK(n+BL/2+tRP). 4. If a Write with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented to activated bank until CK(n+BL/2+1+tDPL+tRP). Last Data-In to Prechage delay(tDPL) which is also called Write Recovery Time (tWR) is needed to guarantee that the last data has been completely written. 5. If A10/AP is High when Row Precharge command being issued, BA0/BA1 are ignored and all banks are selected to be precharged. Rev.1.3/Apr.01 12 HYMD116G7258-H/L PACKAGE DIMENSIONS Front Side 133.35 5.25 131.35 5.171 128.95 10.0 .394 Register PLL 4.24 .167 (2X)4.00 .157 5.077 43.18 1.7 Register Rev.1.3/Apr.01 17.80 .700 (2) 0 2.5 0.098 3.0 .118 1.27+/-0.10 0.050+/-0.004 13 SERIAL PRESENCE DETECT SPD SPECIFICATION (16Mx72 DDR SDRAM Registered DIMM) Rev.0.1 / Apr.01 HYMD116G7258-H/L 16Mx72 DDR SDRAM Registered DIMM Based on 16Mx8 DDR SDRAM with SSTL_2, 4Banks & 4K Refresh SERIAL PRESENCE DETECT Bin Sort : K(DDR266A@CL=2), H(DDR266B@CL=2.5), L(DDR200@CL=2) Function Supported Byte# Function Description 0 Number of Bytes written into serial memory at module manufacturer 1 Total number of Bytes in SPD device 2 Fundamental memory type 3 Number of row address on this assembly K H Hexa Value L K H 128 Bytes 80h 256 Bytes 08h 07h 12 0Ch 1 1 4 Number of column address on this assembly 10 0Ah Number of physical banks on DIMM 1Bank 01h 6 Module data width 72 Bits 48h 7 Module data width (continued) - 00h 8 Module voltage Interface levels(VDDQ) DDR SDRAM cycle time at CAS Latency=2.5(tCK) 10 DDR SDRAM access time from clock at CL=2.5 (tAC) 11 Module configuration type 12 Refresh rate and type 13 Primary DDR SDRAM width 14 Error checking DDR SDRAM data width 15 Minimum clock delay for back-to-back random column address(tCCD) 16 Burst lengths supported 17 Number of banks on each DDR SDRAM 18 CAS latency supported 19 CS latency 20 WE latency 21 DDR SDRAM module attributes 22 DDR SDRAM device attributes : General 23 DDR SDRAM cycle time at CL=2.0(tCK) SSTL 2.5V 7.5ns 7.5ns +/-0.75ns +/-0.75ns 04h 10ns 75h 75h A0h 2 +/-0.8ns 75h 75h 80h 2 A0h A0h 2 75h 80h 2 ECC 02h 15.6us & Self refresh 80h x8 08h x8 08h 1 CLK 01h 2,4,8 0Eh 4 Banks 04h 2, 2.5 0Ch 0 01h 1 02h Registered Address and control inputs PLL 26h +/-0.2Voltage tolerance 7.5ns 10ns +/-0.75ns +/-0.75ns 00h 10ns 75h +/-0.8ns 75h 24 DDR SDRAM access time from clock at CL=2.0(tAC) 25 DDR SDRAM cycle time at CL=1.5(tCK) - 00h 26 DDR SDRAM access time from clock at CL=1.5(tAC) - 00h 27 Minimum row precharge time(tRP) 20ns 20ns 20ns 50h 50h 50h 28 Minimum row activate to row active delay(tRRD) 15ns 15ns 15ns 3Ch 3Ch 3Ch 29 Minimum RAS to CAS delay(tRCD) 20ns 20ns 20ns 50h 50h 50h 30 Minimum active to precharge time(tRAS) 45ns 45ns 50ns 2Dh 2Dh 32h 31 Module row density 32 Command and address signal input setup time(tIS) 0.9ns 0.9ns 1.2ns 90h 90h C0h 33 Command and address signal input hold time(tIH) 0.9ns 0.9ns 1.2ns 90h 90h C0h 34 Data signal input setup time(tDS) 0.5ns 0.5ns 0.6ns 50h 50h 60h 35 Data signal input hold time(tDH) 0.5ns 0.5ns 0.6ns 50h 50h 60h Rev.0.1 / Apr.01 Note DDR SDRAM 5 9 L 128MB 2 2 20h HYMD116G7258-H/L 16Mx72 DDR SDRAM Registered DIMM SERIAL PRESENCE DETECT(continued) Function Supported Byte # 36~61 Function Description K Superset information(may be used in future) 62 SPD Revision code 63 Checksum for Bytes 0~62 64 Manufacturer JEDEC ID Code 65~71 H L Hexa Value K - 89h Hynix JEDEC ID B4h - 00h Hynix(Korea Area) HSA(United States Area) HSE(Europe Area) HSJ(Japan Area) Singapore Asia Area 0*h 1*h 2*h 3*h 4*h 5*h 73 Manufacture part number(Hynix Memory Module) H 48h 74 -------- Manufacture part number(Hynix Memory Module) Y 59h 75 -------- Manufacture part number(Hynix Memory Module) M 4Dh 76 Manufacture part number (DDR SDRAM) D 44h 77 Manufacture part number(Memory density) 1 31h 78 Manufacture part number(Module Depth) 1 31h 36h 79 ------- Manufacture part number(Module Depth) 6 80 Manufacture part number(Module type) G 47h 81 Manufacture part number(Data width) 7 37h 82 -------Manufacture part number(Data width) 2 32h Manufacture part number(Refresh, # of Bank.) Manufacture part number(Component configuration) 85 Manufacture part number(Hyphen) 86 Manufacture part number(Minimum cycle time) 87~90 5(4K refresh,4Bank) 35h 8 38h ‘-’ K H 7Ah ADh Manufacturing location 83 Note 00h - 72 84 L 00h Initial release --------- Manufacturer JEDEC ID Code H 6 2Dh L 4Bh 48h 4Ch Manufacture part number(T.B.D) Blank 91 Manufacture revision code(for Component) Blank 20h 92 Manufacture revision code (for PCB) 0 30h 93 Manufacturing date(week) - - 3 94 20h Manufacturing date(Year) - - 3 95~98 Module serial number - - 4 99~127 Manufacturer specific data (may be used in future) Undefined 00h 5 128~255 Open for customer use Undefined 00h 5 Note : 1. 2. 3. 4. 5. 6. The bank address is excluded These value is based on the component specification These bytes are programmed by code of date week & date year These bytes apply to Hynix’s own Module Serial Number system These bytes undefined and coded as ‘00h’ Refer to Hynix web site Rev.0.1 / Apr.01