ICP-2010 Exportable Voice Grade Channel Processor Features ● OOK, FSK, VFT, PSK, QAM Modems ● Complete Fax processing, including Group 3 and V.17 ● R.101A/B, 2400/1200 bps Strapping ● Async, Bisync, HDLC, SDLC, X.25, SNA, DDCMP, IPARS Protocols ● ASCII-7, ASCII-8, EBCDIC, Baudot Coding ● Analog and PCM E1/T1 Inputs ● PC-based Control Software (standard) Description The ICP-2010 is processor. With can be used as additional DSP simultaneously. M/A-COM’s newest exportable Voice Grade Channel an altogether new DSP board design, the ICP-2010 a single channel processor or configured with one (ICP-2110) to process two voice grade channels The ICP-2010 performs demodulation, demultiplexing, bit stream synchronization and back-end processing for most commercially available modem and voice frequency telegraphy (VFT) signals, as well as complete Group 3 and V.17 FAX signals. In addition, the ICP2010 can generate the modem and VFT signals that it is designed to process. Two analog inputs are available on the ICP-2010, and M/A-COM’s Dual Mode E1/T1 daughter card is used to provide PCM Level 1 input to the ICP-2010. The ICP-2010 comes standard with M/A-COM’s Control Monitor Software for PC-based applications. All of these new features represent the next generation in Voice Grade Channel Processing from M/A-COM’s Communication Technologies Center. Specifications Signal Set V.21, V.22, V.22bis, V.23, V.26A/B/bis/ter, V.27bis/ter, V.29, V.32 Bell 103, 113, 201, 202, 212, 214 V.22bis full-duplex Group 3 and V.17 FAX (to 9.6 kpbs) Multiplexing Formats R.101A/B Strapping Bit Stream Protocols Async, Bisync, HDLC, SDLC, X.25, SNA, DDCMP, IPARS, MNP-4, Binary, BER Diagnostic Display Outputs 2 analog outputs generally used for "X-Y" displays. Power Requirements 85-264 VAC 47-440Hz or 120-364 VDC 9 watts dissipation (ICP-2010) NEMA standard polarized three-prong connector Electromechanical Specifications Standard Chassis 19" wide rack-mountable 2U-high Fan-cooled 10 pounds Trimline Chassis Ruggedized Chassis Half-rack 1U-high 300 cubic inches (8.5" x 20.5" x 1.72") 8 pounds Character Sets ASCII-7, ASCII-8, EBCDIC, Baudot Compression Protocols MNP-5 FAX Coding 1D, 2D and ECM External Inputs 4 kHz analog input 4 kHz low-pass filtered inputs via stereo CODEC BNC female PCM E1/T1 3-lug Triax connector 75 or 120 Ohm selectable CCITT G.732 or DS1 T1D3 formats External Outputs 4 kHz analog input 4 kHz low-pass filtered outputs via stereo CODEC BNC female PCM E1/T1 3-lug Triax connector 75 or 120 Ohm selectable CCITT G.732 or DS1 T1D3 formats Control Interface, Data Output RS-232 Data Link Control (DLC) Interface (control and data) 38.4 kbps Direct Modem Output (clock and data) as well as SCP (Standard Character Protocol) data available on second serial port Temperature Range Operating temperature between 0 and +50° C Storage temperature between -40 and +85° C Cooled exclusively by convection (trimline chassis) Specifications are subject to change without notice. Ordering Information ICP-2010-01 Single VGC Processor Standard Chassis ICP-2010-02 Single VGC Processor Trimline Chassis ICP-2110-01 Dual VGC Processor Standard Chassis ICP-2110-02 Dual VGC Processor Trimline Chassis ICP Control Monitor Included with ICP-2010 orders Contact M/A-COM Communication Technologies Center for further information on ordering and delivery. Warranty This product is warranted for one year, except for damage caused by accident or misuse, provided it is returned for repair to the factory. COMMUNICATION TECHNOLOGIES CENTER 1011 PAWTUCKET BOULEVARD: P.O. BOX 3295 LOWELL, MA 01853-3295 TEL: (508) 442-5000 FAX: (508) 442-4988 V2.00