M I C R O T U N E™ MIXED DIGITAL AND ANALOG TV APPLICATIONS 404X SERIES RF TUNER MODULES APPLICATIONS • Set-top boxes • TV Sets • PC TV Boards FEATURES • Frequency range: 50 MHz to 860 MHz • NTSC and ATSC compatible • Integrated IF demodulator for analog video and audio • Baseband outputs for analog video and audio • Balanced IF output for digital applications • Improved adjacent channel performance for ATSC reception • All functions controlled by I C bus • TTL-Controlled switchable antenna inputs • Low noise figure • AFC byte readable through I C bus • Single 5V supply 2 2 Modules can be implemented with different sockets, filters, interfaces, connectors, and other customizable options within the same pinouts. The 404x Series RF Tuner Module is specifically designed for mixed digital and analog TV reception. This device combines the functions of both an analog multimedia front end and a digital tuner in a single unit. For reception of digitally modulated signals, a balanced IF output has a center frequency of 44 MHz. The IF outputs connect directly with an applicable external SAW filter. An AGC control input allows for external control of the output signal amplitude. This tuner covers a frequency range of 50 MHz to 860 MHz with a channel bandwidth of 6 MHz. The module’s hyperband tuner for analog TV reception covers the frequency range of 50 MHz to 860 MHz and contains an IF part with SAW filter, IF amplifier, and video and sound demodulators. The AF and CVBS signals are available at the audio and video output pins. A video buffer is built in for direct connection to a 75Ω input. For both digital and analog applications, the reception frequency range is divided into VHF low, VHF high, and UHF. Band selection and tuning are done completely via the I²C-bus. In addition, the AFC voltage generated by the IF demodulator is fed to an integrated A/D converter in the PLL IC and is readable via the I²C bus. A digital AFC function can be implemented. A DC/DC converter for 33V generation is built in, so that only a single supply voltage of 5V is required. Product Brief 404X SERIES RF TUNER MODULES PRODUCT BRIEF MIXED DIGITAL AND ANALOG TV APPLICATIONS FUNCTIONAL CHARACTERISTICS PARAMETER Frequency range for digital reception VHF Low VHF High UHF Frequency range for analog reception VHF Low (ch 02 to G) VHF High (ch H to W+26) UHF (ch W+27 to 69) Recommended take-over frequency VHF Low / VHF High UHF IF Frequency Digital modulation (center) Picture carrier Sound carrier Input impedance VHF/UHF Common IF Output Operating temperature Storage temperature Supply voltage MEASUREMENT UNIT 57 to 160 165 to 454 459 to 858 MHz MHz MHz 55.25 to 157.25 163.25 to 451.25 457.25 to 801.25 MHz MHz MHz 162 457 MHz MHz 44 45.75 41.25 MHz MHz MHz 75 75 0 to +60 -25 to +60 5 Ω, Unbalanced Ω, Balanced °C °C V 4040 FI5 404x Series Tuner Modules TUNER MODULE DATA PARAMETER VIDEO OUTPUT PARAMETER CVBS Output level Load impedance Video S/N: VHF UHF Noise limiting sensitivity for video S/N Frequency response 1 MHz 2 MHz 3 MHz 3.58 MHz Differential gain Differential phase C/L Gain C/L Delay MIN TYP MAX 0.8 1 75 46 45 1.2 Vp-p Ω dB dB 45 3 dBµV -1.5 -2 -4 -8 1.5 2 2 -1 10 5 20 50 dB dB dB dB %p-p °p-p % ns -50 -100 -15 -25 UNIT AUDIO OUTPUT PARAMETER Output level: MIN AC DC Output resistance Load impedance AF Level THD+N S/N Frequency response 40 Hz to 15 kHz 2.1 2.2 370 TYP 1.3 2.5 200 460 MAX 2.9 550 0.5 49 -1 1 UNIT Vp-p V Ω kΩ mV rms % dB dB 2ND IF OUTPUT PARAMETER AC Level of 4.5 MHz Load impedance MIN 50 0.5 TYP 120 MAX 4042 FI5 4041 FI5 Voltage gain (80 MHz to 862 MHz) Ch 02 to ch W+26 1 kHz Distance from carrier Noise figure Phase noise 1 kHz Distance from carrier VHF Low VHF High UHF 10 kHz Distance from carrier VHF Low VHF High UHF 100 kHz Distance from carrier VHF Low VHF High UHF VSWR (Antenna input) AGC Range VHF Low VHF High UHF IF Rejection VHF Low VHF High UHF Image rejection VHF Low VHF High (ch H to ch 13) VHF High (ch J to ch W+29) UHF RF Tilt RF Input level 1 dB Compression point VHF Low VHF High UHF CSO / CTB / IP3 Composite triple beat Composite second order beat IP3 (Two tone) MIN TYP 38 36 43 40 7 9 dB dB dB -68 -60 -57 -60 -55 -55 dBc/Hz dBc/Hz dBc/Hz -95 -85 -85 -80 -80 -80 dBc/Hz dBc/Hz dBc/Hz -110 -106 -103 2 -100 -100 -100 4 dBc/Hz dBc/Hz dBc/Hz 45 40 35 MAX UNIT 60 50 50 dB dB dB 50 60 60 dB dB dB 60 60 50 45 dB dB dB dB dB dBµV 2.5 110 45 80 80 80 85 82 84 2 dBµV dBµV dBµV >60 >60 >85 dB dB dBµV UNIT mVp-p Ω World Headquarters • Microtune, Inc., 2201 Tenth Street, Plano, TX 75074 • Tel: 972-673-1600, Fax: 972-673-1602, E-mail: [email protected], Web site: www.microtune.com European Headquarters • Microtune GmbH and Co. KG, Marie Curie Strasse 1, 85055 Ingolstadt / Germany • Tel: +49-841-9378-011, Fax: +49-8419378-010, Sales Tel: +49-841-9378-020, Sales Fax: +49-841-9378-024 Pan-Asian Headquarters • Microtune, Inc. - Hong Kong, Silvercord Tower 1, Room 503, 30 Canton Road, Kowloon, Hong Kong • Tel: +852-2378-8128, Fax: +852-2302-0756 For a detailed list of current sales representatives, visit our Web site at www.microtune.com. The information in this document is believed to be accurate and reliable. Microtune assumes no responsibility for any consequences arising from the use of this information, nor from any infringement of patents or the rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or other rights of Microtune. The information in this publication replaces and supersedes all information previously supplied, and is subject to change without notice. The customer is responsible for assuring that proper design and operating safeguards are observed to minimize inherent and procedural hazards. Microtune assumes no responsibility for applications assistance or customer product design. The devices described in this document are not authorized for use in medical, life-support equipment, or any other application involving a potential risk of severe property or environmental damage, personal injury, or death without prior express written approval of Microtune. Any such use is understood to be entirely at the user’s risk. Microtune, MicroTuner, MicroModule, and the Microtune logo are trademarks of Microtune, Inc. All other trademarks belong to their respective companies. This product is manufactured and protected by the following U.S. patents: 5,805,988; 5,739,730; 5,625,325; 5,737,035; 5,648,744; 5,717,730; 5,847,612; 6,104,242; 6,100,761; 6,144,402; and additional patents pending or filed. Entire contents Copyright © 2000 Microtune, Inc. PB-00019 Rev 1.3 — December 2000 Page 2 of 2