74VCXH16245 LOW VOLTAGE CMOS 16-BIT BUS TRANSCEIVER (3-STATE) WITH 3.6V TOLERANT INPUTS AND OUTPUTS ■ ■ ■ ■ ■ ■ ■ ■ ■ 3.6V TOLERANT INPUTS AND OUTPUTS HIGH SPEED: tPD = 2.5 ns (MAX.) at VCC = 3.0 to 3.6V tPD = 3.2 ns (MAX.) at VCC = 2.3 to 2.7V POWER-DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24 mA (MIN) at VCC = 3.0V |IOH| = IOL = 18 mA (MIN) at VCC = 2.3V OPERATING VOLTAGE RANGE: VCC (OPR) = 2.3V to 3.6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 16245 BUS HOLD PROVIDED ON BOTH SIDES LATCH-UP PERFORMANCE EXCEEDS 300mA ESD PERFORMANCE: HBM >2000V; MM > 200V T (TSSOP48 Package) ORDER CODES : 74VCXH16245T PIN CONNECTION DESCRIPTION The VCXH16245 is a low voltage CMOS 16-BIT BUS TRANSCEIVER (3-STATE) fabricated with sub-micron silicon gate and five layer metal wiring C2MOS technology. It is ideal for low power and very high speed 2.3 to 3.6V applications; it can be interfaced to 3.6V signal enviroment for both inputs and outputs. This IC is intended for two-way asynchronous communication beetwen data buses; the direction of data trasmission is determined by DIR input. The two enable inputs nG can be used to disable the device so that the buses are effectively isolated. Bus hold on data inputs is provided in order to eliminate te need for external pull-up or pull-down resistor. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. March 1999 1/9 74VCXH16245 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No IEC LOGIC SYMBOLS SYMBOL NAME AND FUNCT ION 1 1DIR 2, 3, 5, 6, 8, 9, 11, 12 1B0 to 1B7 Directional Control Data Inputs/Outputs 13, 14, 16, 17, 19, 20, 22, 23 2B0 to 2B7 Data Inputs/Outputs 24 2DIR Directional Control 25 2G Output Enabel Input 36, 35, 33, 32, 30, 29, 27, 26 2A0 to 2A7 Data Inputs/Outputs 47, 46, 44, 43, 41, 40, 38, 37 1A0 to 1A7 Data Inputs/Outputs 48 1G Output Enabel Input 4,10, 15, 21, 28, 34, 39, 45 GND Ground (0V) 7, 18, 31, 42 VCC Positive Supply Voltage TRUTH TABLE INPUT G OUT PUT A BUS L L OUTPUT INPUT A= B L H INPUT OUTPUT B= A H X Z Z Z X:”H” or ”L” Z: High impedance 2/9 F UNCTION DIR B BUS 74VCXH16245 ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply Voltage Value Unit -0.5 to + 4.6 V VI DC Input Voltage -0.5 to + 4.6 V VO DC Output Voltage (OFF state) -0.5 to + 4.6 V VO DC Output Voltage (High or Low State) (note1) -0.5 to VCC + 0.5 V IIK DC Input Diode Current - 50 mA IOK DC Output Diode Current (note2) ± 50 mA IO DC Output Source/Sink Current ± 50 mA DC VCC or Ground Current Per Supply Pin ± 100 mA 400 mW ICC orIGND PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) -65 to +150 o 300 o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. 1) IO absolute maximum rating must be observed 2) VO < GND, VO > VCC RECOMMENDED OPERATING CONDITIONS Symbol Parameter Value Unit Supply Voltage 2.3 to 3.6 V VI Input Voltage -0.3 to 3.6 V VO Output Voltage (OFF state) 0 to 3.6 V VO Output Voltage (High or Low State) 0 to VCC V VCC IOH, IOL High or Low Level Output Current (VCC = 3.0 to 3.6V) ± 24 mA IOH, IOL High or Low Level Output Current (VCC = 2.3 to 2.7V) ± 18 mA Top dt/dv Operating Temperature: Input Transition Rise or Fall Rate (V CC = 3.0V) (note 1) -40 to+85 0 to 10 o C ns/V 1) VIN from0.8V to 2.0V, VCC = 3.0V 3/9 74VCXH16245 DC SPECIFICATIONS (2.7V < VCC ≤ 3.6V unless otherwise specified) Symb ol Parameter Test Co nditi ons VIH High Level Input Voltage VIL Low Level Input Voltage VOH High Level Output Voltage Min. IO=-100 µA VCC-0.2 IO=-12 mA 2.2 IO=-18 mA 2.4 3.0 IO=-24 mA 2.2 2.7 to 3.6 IO=100 µA 0.2 IO=12 mA 0.4 IO=18 mA 0.4 IO=24 mA 0.55 VI = VIH or VIL VI = VIH or VIL 3.0 3.0 II(HOLD) Input Leakage Current Input Hold Current IOZ 3 State Output Leakage Current Ioff Power Off Leakage Current ICC Quiescent Supply Current ∆ICC ICC incr. per input V 0.8 2.7 to 3.6 2.7 II Max. 2.0 2.7 to 3.6 3.0 Low Level Output Voltage Un it o 2.7 VOL Value -40 to 85 C V CC (V) 2.7 to 3.6 3 V ±5 VI = VCC orGND VI = 0.8 V 75 VI = 2 V -75 V V µA µA 3.6 VI = 0 to 3.6 V ±500 2.7 to 3.6 VI = VIH orVIL VO = 0 to 3.6V ±10 µA 0 VI orVO = 0 to 3.6V 10 µA 2.7 to 3.6 VI = VCC orGND 20 VI orVO = VCC to 3.6 V ±20 750 µA 2.7 to 3.6 VIH = VCC -0.6V µA DC SPECIFICATIONS (2.3V < VCC ≤ 2.7V unless otherwise specified) Symb ol Parameter Test Co nditi ons VIH High Level Input Voltage VIL Low Level Input Voltage VOH High Level Output Voltage Min. IO=-100 µA VI = VIH or VIL 2.3 VOL Low Level Output Voltage 2.3 to 2.7 2.3 2.3 II II(HOLD) 4/9 Input Leakage Current Input Hold Current IOZ 3 State Output Leakage Current Ioff Power Off Leakage Current ICC Quiescent Supply Current 2.3 to 2.7 2.3 Max. V 0.7 2.3 to 2.7 2.3 Un it 1.6 2.3 to 2.7 2.3 Value -40 to 85 o C V CC (V) VI = VIH or VIL V VCC-0.2 IO=-6 mA 2.0 IO=-12 mA 1.8 IO=-18 mA 1.7 V IO=100 µA 0.2 IO=12 mA 0.4 IO=18 mA 0.6 ±5 VI = VCC orGND VI = 0.7 V 45 VI = 1.7 V -45 V µA µA 2.3 to 2.7 VI = VIH orVIL VO = 0 to 3.6V ±10 µA 0 VI orVO = 0 to 3.6V 10 µA 2.3 to 2.7 VI = VCC orGND 20 VI orVO = VCC to 3.6 V ±20 µA 74VCXH16245 DYNAMIC SWITCHING CHARACTERISTICS (Ta = 25oC, Input tr = tf = 2.0ns, CL = 30pF) Symb ol Parameter Test Con dition s Value VOLP VOLV VOHV Dynamic Peak Low Voltage Quiet Output (note 1, 3) 2.5 Dynamic Valley Low Voltage Quiet Output (note 1, 3) 2.5 Dynamic Valley High Voltage Quiet Output (note 2, 3) 2.5 Un it o T A = 25 C V CC (V) Min . 3.3 3.3 3.3 T yp. VIL = 0 V VIH = VCC 0.6 VIL = 0 V VIH = VCC -0.6 VIL = 0 V VIH = VCC 1.9 Max. V 0.8 V -0.8 V 2.2 1) Number ofoutputs defined as ”n”. Measured with”n-1” outputs switching from HIGH to LOW or LOW t o HIGH. The remaining output is measured in the LOW state. 2) Number ofoutputs defined as ”n”. Measured with”n-1” outputs switching from HIGH to LOW or LOW t o HIGH. The remaining output is measured in the HIGH state. 3) Parameters guaranteed by design. AC ELECTRICAL CHARACTERISTICS (CL = 30 pF, RL = 500 Ω, Input tr = tf = 2.0 ns) Symb ol Parameter V CC (V) Test Con dition Waveform tPLH tPHL Propagation Delay Time 2.3 to 2.7 3.0 to 3.6 tPZL tPZH Output Enable Time tPLZ tPHZ Output Disable Time 2.3 to 2.7 3.0 to 3.6 2.3 to 2.7 tOSLH tOSHL Output to Output Skew Time (note 1, 2) Value -40 to 85 o C 1 2 2 3.0 to 3.6 2.3 to 2.7 3.0 to 3.6 Min. 1.0 0.8 Max. 3.2 2.5 1.0 0.8 1.0 4.9 3.8 4.2 0.8 3.7 0.5 0.5 Un it ns ns ns ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any twooutputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = |tPLHm - tPLHn|, tOSHL = |tPHLm - tpHLn|) 2) Parameter guaranteed by design CAPACITIVE CHARACTERISTICS Symb ol Parameter Test Co nditi ons Valu e Un it o T A = 25 C V CC (V) Min. T yp. 4 Max. Input Capacitance 2.5 or 3.3 VIN = 0V or VCC COUT Output Capacitance 2.5 or 3.3 VIN = 0V or VCC 8 pF CPD Power Dissipation Capacitance (note 1) 2.5 or 3.3 fIN = 10MHz VIN = 0V or VCC 28 pF CIN pF 1) CPD isdefined as the value of the IC’sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. Average operting current can be obtained by the following equation. I CC(opr) = CPD • VCC • fIN + ICC/16 (per circuit) 5/9 74VCXH16245 TEST CIRCUIT T EST SW IT CH tPLH , tPHL Open tPZL , tPLZ (VCC = 3.0 to 3.6V) 6V tPZL , tPLZ (VCC = 2.3 to 2.7V ) 2VCC tPZH , tPHZ GND CL = 30 pF or equivalent (includes jigand probe capacitance) RL = R1 = 500Ω orequivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM SYMBOL VALUES Symbo l VIH 6/9 V CC 3.0 to 3.6V 2.3 to 2.7V 2.7V VCC VM 1.5V VCC/2 VX VOL + 0.3V VOL + 0.15V VY VOH - 0.3V VOH - 0.15V 74VCXH16245 WAVEFORM 1: PROPAGATION DELAYS (f=1MHz; 50% duty cicle) WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cicle) 7/9 74VCXH16245 TSSOP48 MECHANICAL DATA mm DIM. MIN. inch TYP. MAX. A MIN. 1.1 MAX. 0.433 A1 0.05 0.10 0.15 0.002 0.004 0.006 A2 0.85 0.9 0.95 0.335 0.354 0.374 b 0.17 0.27 0.0067 0.011 c 0.09 0.20 0.0035 0.0079 D 12.4 12.5 12.6 0.408 0.492 0.496 E 7.95 8.1 8.25 0.313 0.319 0.325 E1 6.0 6.1 6.2 0.236 0.240 0.244 e 0.5 BSC 0.0197 BSC K 0o 4o 8o 0o 4o 8o L 0.50 0.60 0.70 0.020 0.024 0.028 A A2 A1 b K e E1 PIN 1 IDENTIFICATION 1 L E c D 8/9 TYP. 74VCXH16245 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics 1999 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com . 9/9